Temperature Research of Permanent Magnet Brushless DC Motor for Electric Balanced Vehicle

A power system structure composed of a brushless DC motor and a cycloidal reducer for electric balanced vehicle has been proposed, and the temperature of important components in this structure would be discussed. The loss generated by the cycloid reducer is negligible, it’s only need to analyze the thermal field of motor. Since the temperature change will affect the material properties of the target motor, the electromagnetic and temperature fields, involved in the motor, are selected for coupling calculation to determine whether the final temperature distribution can meet the requirements of vehicle for use.

Simulation Research of Fault Model of Detecting Rotor Dynamic Eccentricity in Brushless DC Motor Based on Motor Current Signature Analysis

基于Ansoft／Maxwell设置动态偏心故障，建立求解电机电感和磁链的有限元模型，通过仿真，证明了将感应电机动态偏心故障的特征频率经过简化后，同样适用于无刷直流电动机。基于Ansoft／Simplorer建立无刷直流电动机系统的仿真模型。在电机稳态运行下，对定子电流进行傅里叶分析，研究并建立基于定子电流监测动态偏心故障的仿真模型：动态偏心故障与特征频率的关系、动态偏心故障程度与特征频率幅值的关系。进而研究了无刷直流电动机稳态运行时转速波动对偏心故障监测的影响。仿真结果表明，转子偏心程度加大，特征频率的幅值增加。

Analysis of the Magnetic Flux Density, the Magnetic Force and the Torque in a 3D Brushless DC Motor

As permanent magnet motors and generators produce torque, vibration occurs through the small air gap due to the alternating magnetic forces created by the rotating permanent magnets and the current switching of the coils. The magnetic force can be calculated from the flux density by finite element methods and the Maxwell stress tensor in cy-lindrical coordinates. In this paper the magnetic flux density, the magnetic force and the torque of a real three dimen-sional brushless DC motor are simulated using Maxwell 3 D V 11.1.

EFFECTIVE DOUBLE LOOP CONTROL FOR A SQUARE WAVE BRUSHLESS DC MOTOR

A new type of brushless DC motor has been developed by using a square wave rare earth permanent magnet synchronous motor with its double loop control circuit. The double loop control scheme of the drive system yields a combination of desired characteristics including simplified control structure, small ripple torque, high speed accuracy, wide operating speed range, and fast dynamic response. Experimental results confirm excellent characteristics of the motor.

An Advance Commutation Control Method for Low Torque Ripple of Brushless DC Motors

该文给出一种优化的无刷直流电动机变母线电压六拍控制方法。既解决了传统六拍控制策略中由于绕组电感所造成的电流滞后问题,又改善了由于换相所造成的电流脉动问题。该方法是通过在每两拍之间插入一小段缓冲区来实现的,该缓冲区使下一拍将要切入的电流提前切入,同时使当前拍将要切出的电流延迟切出。通过确定缓冲区的起始位置,即超前换相角的大小,保证每一拍所对应的相电流的中心和反电动势的中心重合。通过选取缓冲区开关器件PWM调制的占空比,降低电机运行过程中的换相转矩脉动。该文方法只需根据负载大小选取超前换相角,一旦选定适用于所有转速。文中给出了该方法的理论推导过程和实验验证波形,从实验结果可以发现,电流滞后被消除,换相电流脉动显著减小,电机的利用率得到提高。

Anti-reverse rotation startup method for sensorless brushless DC motor

In order to start up the brushless DC motor （BLDCM） without reverse rotation and smoothly switch the running state of the motor, a novel startup and smoothly switching method for a sensodess BLDCM is presented. Based on the saturation effect of the stator iron, six short voltage pulses are applied to determine the initial rotor position and the rotor can be found within 60°. After that, a series of short and long voltage pulses are used to accelerate the motor and the variation of the response current is utilized to detect the rotor position dynamically. When the motor reaches a certain speed at which the back-electromotive force （EMF） method can be applied, all the power devices are turned off and the running state of the motor is smoothly switched at the moment determined by the relationship between the terminal voltage waveform and the commutation phases. The experimental results verify the feasibility and validity of the proposed method.

A neural network-based commutation optimization strategy and drive system design for brushless DC motor

An optimized commutation method based on backpropagation(BP)neural network is proposed to resolve the low stability and high-power consumption caused by inaccurate commutation point prediction in conventional commutation strategy during acceleration and deceleration.This article also builds a complete brushless DC motor drive system based on the GD32F103 micro control unit(MCU),with an Artix-7 XC7A35T field programmable gate array(FPGA)to meet the performance requirements of neural network calculation for real-time motor commutation control.Experimental results show that the proposed optimization strategy can effectively improve the system stability during system acceleration and deceleration,and reduce the current spikes generated during speed chan-ges.The system power consumption is reduced by about 11.7%on average.

New Method to Restrain Pumping Voltage of Braking Procedure for Brushless DC Motor of Electric Armored Vehicle

In order to restrain the high pumping voltage of braking procedure which is harmful to the system of electric armored vehicle. Based on the analysis of pumping voltage of the braking procedure, the relation between pumping voltage and PWM ratio is derived and a new digital control method to restrain the pumping voltage by changing PWM ratio is put forward. Because the capacitance is decreased effectively, the volume of controller is reduced and the performance to price ratio is improved. The results of computer simulation and experiment proved that this method is feasible and valid.

Design and implementation of a position sensorless control method for brushless DC motors

Because brushless direct current(BLDC) motors have the advantages of a compact size, high power density, high efficiency, and long operating life time, they are widely used in many industrial products and electric traction systems. It is known that the BLDC motors have no brushes for commutation. They are commutated with electronically commutation. So, the rotor position information of the BLDC motors must be known to understand which winding will be energized according to the energizing sequence. In most of the existing BLDC motor drivers, rotor position information is detected by Hall effect sensors. This kind of mechanical position sensors will bring additional connections and costs, reliability decrease and noise increase. In order to improve the control performance and extend the range of speed regulation for BLDC motors, a position sensorless control method is proposed in this paper. In the proposed control method, rotor position information of the BLDC motors is detected from the back electromagnetic forces(back-EMFs) which are estimated by an unknown-input observer with line to line currents and line to line voltages. For the purpose of verifying the effectiveness of the proposed control method, a model is built and simulated on the Matlab/Simulink platform. The simulation results show that the speed regulation performance of BLDC motors is improved compared with using Hall effect sensors. At the same time, the reliability of the BLDC motors is improved and the costs of them are reduced because the position sensor is eliminated.

Robust Control Strategy for the Speed Control of Brushless DC Motor

Brushless DC motor ( BLDCM) speed servo system is multivariable,nonlinear and strong coupling. The parameter variation, the cogging torque and the load disturbance easily influence its performance. Therefore,it is difficult to achieve superior performance by using the conventional PID controller. To solve the deficiency,the paper represents the algorithm of active-disturbance rejection control ( ADRC) based on back-propagation ( BP) neural network. The ADRC is independent on accurate system and its extended-state observer can estimate the disturbance of the system accurately. However,the parameters of Nonlinear Feedback ( NF) in ADRC are difficult to obtain. So in this paper,these parameters are self-turned by the BP neural network. The simulation and experiment results indicate that the ADRC based on BP neural network can improve the performances of the servo system in rapidity,control accuracy,adaptability and robustness.

Highly Effective Brushless DC Motor in Which Unidirectional Current Flows in

Authors developed a highly effective brushless DC motor with a simple operation principle. If the operation principle of the motor is simple, a drive circuit will also become simple and its production cost will be lower. From the above fact, Minato motor was noticed. In this motor, a unidirectional current flows in the electromagnets. In other words, unidirectional windings are used. In this motor, only strong repulsive force is utilized when a permanent magnet of a rotor and an electromagnet of a stator are adjacent. Hence, torque constant becomes higher and the efficiency of the motor is high. However, an effective value of the electromagnetic current increases because a large current flows in a short period. Therefore, copper loss increases and the efficiency of the motor decreases. In order to solve above defects, a new motor is proposed. From the experiment, it is clarified that the efficiency of the proposed motor is higher than that of the commercial motors.

Comparative Study between the PID Regulator and the Fuzzy Regulator Applied to the Operation of a Brushless DC Motor

This paper presents the results of research on speed regulation of a brushless DC motor. This is mainly a comparative study between a PID regulator and a fuzzy regulator applied to the operation of this type of engine in order to find the best control. The BLDC engine must operate under various speed and load conditions with improved performance and robust and complex speed control. Because of this complexity, the traditional PID command encounters difficulties in controlling the speed of a BLDC. Another control technique is currently developing and is producing good results. This is the fuzzy controller that handles process control problems, that is, managing a process based on a given set point per action on the variables that describe the process. To achieve the desired results, the brushless DC machine model will be studied. With the model obtained, both types of regulator will be tested. A synthesis of the observed comparison results will enable a conclusion to be drawn on the performance of the two types of regulators driving a BLDC (Brushless DC).

High temperature brushless DC motor system and its operation mode control

The high temperature (175 ℃) operation of a motor spells out special requirements for control algorithms, materials and elements. The stability of motor characteristic is guaranteed by the digital control strategy. Constant velocity operation is achieved by phase locked loop (PLL), and constant power operation is achieved by a current restricting circuit. A motor for constant speed and constant power operation has been built and the speed control system is tuned by MATLAB simulation. Experimental and simulation results for operation mode control of brushless DC motor are presented.

Analysis of Torque Ripple of Permanent Magnet Brushless DC Motor

Torque tripple has significant effect on performance of permanent magnet brushless DC motor. This paper presents a mathematical model built for such a motor, the analysis of torque tripple for a brushless DC motor with sinusoidal flux distribution, which is verified by torque tripple experiments run with a test motor, and equations developed for torque tripple resulting from different sator current errors.

Sensorless Control of Four-Switch Inverter for Brushless DC Motor Drive and Its Simulation

The major function of this proposed research is to control the speed of the brushless DC motor with sensor less control for four-switch three phase inverter. This proposed system is simplified the topological structure of the conventional six-switch three phase inverter. In this proposed method, a new structure of four-switch three phase inverter [1] with reduced number of switches for system is introduced to reduce the mechanical commutation, switching losses that occur in the six-switch method. The proposed inverter fed brushless DC motor used in sensorless control schemes which is used for sensing positioning signals. To improve sensor less control performance, four-switch electronic commutation modes based proportional intergral controller scheme is implemented. In this four-switch three phase inverter reduction of switches, low cost control and saving of hall sensor were incorporated. The feasibility of the proposed sensor less control four-switch three phase inverter fed brushless DC motor drive is implemented, analysed using MATLAB/SIMULINK, effective simulation results have been validated out successfully.

Solar PV System for Energy Conservation Incorporating an MPPT Based on Computational Intelligent Techniques Supplying Brushless DC Motor Drive

This paper proposes an effective Maximum Power Point Tracking (MPPT) controller being incorporated into a solar Photovoltaic system supplying a Brushless DC (BLDC) motor drive as the load. The MPPT controller makes use of a Genetic Assisted Radial Basis Function Neural Network based technique that includes a high step up Interleaved DC-DC converter. The BLDC motor combines a controller with a Proportional Integral (PI) speed control loop. MATLAB/Simulink has been used to construct the dynamic model and simulate the system. The solar Photovoltaic system uses Genetic Assisted-Radial Basis Function-Neural Network (GA-RBF-NN) where the output signal governs the DC-DC boost converters to accomplish the MPPT. This proposed GA-RBF-NN based MPPT controller produces an average power increase of 26.37% and faster response time.

Steering Control of Wheeled Armored Vehicle with Brushless DC Motor

Considering the steering characters of one type of wheeled armored vehicle, a brushless direct current （DC） motor is adapted as the actuator for steering control. After investigating the known algorithms, one kind of algorithm, which combines the fuzzy logic control with the self-adapting PID control and the startup and pre-hrake control, is put forward. Then a test-bed is constructed, and an experiment is conducted. The result of experiment confirms the validity of this algorithm in steering control of wheeled armored vehicle with brushless DC motor.

Adaptive Internal Model Control of a DC Motor Drive System Using Dynamic Neural Network

This work concerns the study of problems relating to the adaptive internal model control of DC motor in both cases conventional and neural. The most important aspects of design building blocks of adaptive internal model control are the choice of architectures, learning algorithms, and examples of learning. The choice of parametric adaptation algorithm for updating elements of the conventional adaptive internal model control shows limitations. To overcome these limitations, we chose the architectures of neural networks deduced from the conventional models and the Levenberg-marquardt during the adjustment of system parameters of the adaptive neural internal model control. The results of this latest control showed compensation for disturbance, good trajectory tracking performance and system stability.

基于DCS-惯性权重组合的柔性机械臂运动轨迹控制系统研究

为了有效调控机械臂运动幅度,避免柔性机械臂实际运动轨迹与目标轨迹发生较大的偏差,设计一种基于分散控制系统(DCS)-惯性权重组合的柔性机械臂运动轨迹控制系统,它是一个集合了计算机、通信、显示和控制的计算机系统,该系统由过程控制和过程监控。通过DCS算法控制监测对象行为幅度并计算柔性机械臂惯性权重,利用DCS-惯性权重组合求解素数控制指标的具体数值,实现了对柔性机械臂运动轨迹控制系统的软件设计。实验结果表明,DCS-惯性权重组合算法作用下的机械臂末端坐标在横轴、纵轴、空间轴方向上的运动幅值均可以被控制在10个单位长度之内,并且在0.52 s内进入机械臂运动轨迹最佳控制状态,运动轨迹差值最大仅为0.01 rad,验证了该系统具备可行性和有效性。

Analysis of torque-current characteristic of brushless DC motor driven by three-phase H-bridge

Presents the simulation and analysis of the steady state characteristic of a brushless DC motor studies the torque current characteristic of the motor as well and discusses the design of a current measure circuit for torque controlling.