The wettability and bonding in Ni/Ti(C, N) systems with multiple carbide additions were studied by sessile drop technique and vacuum brazing technique, respectively. The phase characterizations of substrates and fract...The wettability and bonding in Ni/Ti(C, N) systems with multiple carbide additions were studied by sessile drop technique and vacuum brazing technique, respectively. The phase characterizations of substrates and fracture surfaces were conducted by XRD. The microstructures at metal/ceramic interfaces and fracture surfaces were observed via SEM in back scattered mode and second electron mode, respectively. Furthermore, an X-ray energy-dispersive spectrometer (EDS) attached to SEM was used to study the elements diffusion in interfacial regions. The results reveal that diffusion and dissolution mechanism controlled reactive wetting takes place in the system in high temperature wetting. Results also show that the contact angles decrease with multiple carbide additions, and the effect of multiple carbide additions is stronger than that of single additions. The contact angle reaches the lowest value in the lowest TiC content case. The enhancement of the wettability is due to alloying procedure during high tempe展开更多
Based on ANSYS FEM software, the distribution of residual stress in the diffusion bonding joints between Ti（ C,N） metallic ceramic/interlayer/4OCr steel was calculated and experimentally ver^ed. The results showed t...Based on ANSYS FEM software, the distribution of residual stress in the diffusion bonding joints between Ti（ C,N） metallic ceramic/interlayer/4OCr steel was calculated and experimentally ver^ed. The results showed that the trend on the distribution of residual stress field in the joints was not changed with the use of interlayer. The maximum residual stress was always located in metallic ceramic with area ranging from 1 mm to 4 mm to the interlayer. The maximum residual stress in the joints was also affected by diffusion temperature. The satellite pulse current during the initial stage on diffusion bonding can promote the formation of liquid film at the interface, by which diffusion temperature and loading pressure can be greatly decreased. The crack initiation was easily produced at the corner of Ti （ C, N） metallic ceramic close to the interlayer. If a higher residual stress produced in the joints, the crack was propagated into the whole ceramic.展开更多
基金The authors wish to acknowledge the financial support from the National Natural Science Foundation of Chinathe Natural Science Foundation of Anhui Provincethe Project of Key Teachers of University of Education Ministry of China under contract No.50072003,No.03044902 and No.GG-805-10359-1840,respectively.
文摘The wettability and bonding in Ni/Ti(C, N) systems with multiple carbide additions were studied by sessile drop technique and vacuum brazing technique, respectively. The phase characterizations of substrates and fracture surfaces were conducted by XRD. The microstructures at metal/ceramic interfaces and fracture surfaces were observed via SEM in back scattered mode and second electron mode, respectively. Furthermore, an X-ray energy-dispersive spectrometer (EDS) attached to SEM was used to study the elements diffusion in interfacial regions. The results reveal that diffusion and dissolution mechanism controlled reactive wetting takes place in the system in high temperature wetting. Results also show that the contact angles decrease with multiple carbide additions, and the effect of multiple carbide additions is stronger than that of single additions. The contact angle reaches the lowest value in the lowest TiC content case. The enhancement of the wettability is due to alloying procedure during high tempe
基金The authors are grateful to the financial support for this research from National Natural Science Foundation of China （Grant No. 51175259） , Jiangsu Science and Technology Planning Project （No. BK2011494） and University Science Research Project of Jiangsu Province （ 11KJAd30005 ）.
文摘Based on ANSYS FEM software, the distribution of residual stress in the diffusion bonding joints between Ti（ C,N） metallic ceramic/interlayer/4OCr steel was calculated and experimentally ver^ed. The results showed that the trend on the distribution of residual stress field in the joints was not changed with the use of interlayer. The maximum residual stress was always located in metallic ceramic with area ranging from 1 mm to 4 mm to the interlayer. The maximum residual stress in the joints was also affected by diffusion temperature. The satellite pulse current during the initial stage on diffusion bonding can promote the formation of liquid film at the interface, by which diffusion temperature and loading pressure can be greatly decreased. The crack initiation was easily produced at the corner of Ti （ C, N） metallic ceramic close to the interlayer. If a higher residual stress produced in the joints, the crack was propagated into the whole ceramic.
