New Al4C3-containing Al-Ti-C master alloys (Al-0.6Ti-1C and Al-1Ti-1C) were developed by introducing Ti element into Al-C melt using melt reaction method,in which most of the TiC particles distribute around Al4C3 part...New Al4C3-containing Al-Ti-C master alloys (Al-0.6Ti-1C and Al-1Ti-1C) were developed by introducing Ti element into Al-C melt using melt reaction method,in which most of the TiC particles distribute around Al4C3 particles. It is believed that most of the C firstly reacts with Al melt and form Al4C3 particles by the reaction Al(l)+C(s)→Al4C3(s),and after adding Ti into the Al-C melt,the size of Al4C3 particles is decreased and the distribution of Al4C3 is improved through the reaction Ti(solute)+Al4C3(s)→ TiC(s)+Al(l). With the addition of 1% Al-1Ti-1C master alloy,the average grain size of AZ31 is reduced sharply from 850 μm to 200 μm,and the grain morphology of α-Mg transits from a fully-developed equiaxed dendritic structure to a petal-like shape. Al-C-O-Mn-Fe compounds are proposed to be potent nucleating substrates for primary Mg. Appropriate addition of Ti is believed to increase the grain refinement efficiency of Al4C3-containing Al-Ti-C master alloys in AZ31 alloy.展开更多
A new polymer named polyferrocarbosilane(PFCS) was prepared from polydimethylsilane and ferrocene. The spinnability of this polymer can be tailored by controlling the content of ferrocene in the polymer. The prepared ...A new polymer named polyferrocarbosilane(PFCS) was prepared from polydimethylsilane and ferrocene. The spinnability of this polymer can be tailored by controlling the content of ferrocene in the polymer. The prepared polymer was spun into a continuous polymer fiber that was subsequently cured in air and heat-treated finally in N2 up to 1 350 ℃ for conversion into Si-Fe-C-O fibers. The resulted Si-Fe-C-O fibers display low specific resistance and magnetic property due to the existence of Fe, which also reduces the specific resistance significantly to 10-2Ω·cm at room temperature when the amount of ferrocene in feed is as low as 3.0% (mass fraction). The resulted Si-Fe-C-O fibers, with C/Si molar ratio of about 1.3 and the maximum Fe content of about 2.0% (mole fraction), are composed of β-SiC and small amount of Fe3Si-like crystalline and have an average tensile strength of about 2.0 GPa.展开更多
基金Project(50625101) supported by the National Natural Science Foundation for Distinguished Young Scholars of ChinaProject(106103) supported by Key Project of Science and Technology Research of Ministry of Education of China
文摘New Al4C3-containing Al-Ti-C master alloys (Al-0.6Ti-1C and Al-1Ti-1C) were developed by introducing Ti element into Al-C melt using melt reaction method,in which most of the TiC particles distribute around Al4C3 particles. It is believed that most of the C firstly reacts with Al melt and form Al4C3 particles by the reaction Al(l)+C(s)→Al4C3(s),and after adding Ti into the Al-C melt,the size of Al4C3 particles is decreased and the distribution of Al4C3 is improved through the reaction Ti(solute)+Al4C3(s)→ TiC(s)+Al(l). With the addition of 1% Al-1Ti-1C master alloy,the average grain size of AZ31 is reduced sharply from 850 μm to 200 μm,and the grain morphology of α-Mg transits from a fully-developed equiaxed dendritic structure to a petal-like shape. Al-C-O-Mn-Fe compounds are proposed to be potent nucleating substrates for primary Mg. Appropriate addition of Ti is believed to increase the grain refinement efficiency of Al4C3-containing Al-Ti-C master alloys in AZ31 alloy.
文摘A new polymer named polyferrocarbosilane(PFCS) was prepared from polydimethylsilane and ferrocene. The spinnability of this polymer can be tailored by controlling the content of ferrocene in the polymer. The prepared polymer was spun into a continuous polymer fiber that was subsequently cured in air and heat-treated finally in N2 up to 1 350 ℃ for conversion into Si-Fe-C-O fibers. The resulted Si-Fe-C-O fibers display low specific resistance and magnetic property due to the existence of Fe, which also reduces the specific resistance significantly to 10-2Ω·cm at room temperature when the amount of ferrocene in feed is as low as 3.0% (mass fraction). The resulted Si-Fe-C-O fibers, with C/Si molar ratio of about 1.3 and the maximum Fe content of about 2.0% (mole fraction), are composed of β-SiC and small amount of Fe3Si-like crystalline and have an average tensile strength of about 2.0 GPa.