纳米C-S-H/PCE对蒸养UHPC力学性能增强机理研究

目前超高性能混凝土(UHPC)制品的力学性能有待进一步提升,采用纳米C-S-H/PCE对UHPC进行增强在理论上是一种可行的技术途径。本文研究了蒸养条件下掺入以聚羧酸(PCE)为分散剂的纳米水化硅酸钙(C-S-H/PCE)对UHPC力学性能的影响,通过测试水化热、水化产物、微观形貌和孔结构等对其机理进行了分析。结果表明,掺入3.0%(质量分数)纳米C-S-H/PCE可以显著提高蒸养UHPC的抗压强度和抗折强度。掺入纳米C-S-H/PCE可以促进UHPC的早期水化,生成更多的水化硅酸钙(C-S-H)凝胶,使水化放热温峰增高,并缩短达到水化温峰的时间。掺入纳米C-S-H/PCE可有效改善蒸养UHPC的孔结构,在掺量为3.0%(质量分数)时总孔隙率最小,有害孔比例最低。该研究可为纳米C-S-H/PCE在蒸养UHPC中的应用提供参考。

10℃条件下纳米C-S-H掺量对水泥早期水化的影响

目的探究10℃条件下不同掺量纳米C-S-H对水泥早期水化进程及强度发展的影响,并分析其早强剂作用机理。方法通过溶液共沉淀法制备纳米C-S-H悬浮液,将其掺入到普通硅酸盐水泥中,在10℃条件下进行养护,分析其对水泥凝结时间、抗折强度、抗压强度的影响;通过XRD、TG等检测手段分析水泥的水化进程及对水化产物的影响。结果掺入0.05%纳米C-S-H,可使水泥初凝时间缩短9.9%,终凝时间缩短10.4%;24 h时抗折强度和抗压强度分别提高了34%和33.5%。纳米C-S-H的掺入造成水泥3 d抗折强度略有降低。水化产物中Ca(OH)2质量分数在12 h、16 h和24 h时较参比样分别提高了17.6%、21.3%和29.6%。结论在10℃条件下,纳米C-S-H的加入能够有效促进C 3S和C 2S的水化过程,形成更多的水化产物,从而缩短水泥凝结时间,提高24 h内水泥砂浆强度,28 d强度没有显著降低。

Characterization, preparation, and reuse of metallic powders for laser powder bed fusion: a review

Laser powder bed fusion(L-PBF) has attracted significant attention in both the industry and academic fields since its inception, providing unprecedented advantages to fabricate complex-shaped metallic components. The printing quality and performance of L-PBF alloys are infuenced by numerous variables consisting of feedstock powders, manufacturing process,and post-treatment. As the starting materials, metallic powders play a critical role in infuencing the fabrication cost, printing consistency, and properties. Given their deterministic roles, the present review aims to retrospect the recent progress on metallic powders for L-PBF including characterization, preparation, and reuse. The powder characterization mainly serves for printing consistency while powder preparation and reuse are introduced to reduce the fabrication costs.Various powder characterization and preparation methods are presented in the beginning by analyzing the measurement principles, advantages, and limitations. Subsequently, the effect of powder reuse on the powder characteristics and mechanical performance of L-PBF parts is analyzed, focusing on steels, nickel-based superalloys, titanium and titanium alloys, and aluminum alloys. The evolution trends of powders and L-PBF parts vary depending on specific alloy systems, which makes the proposal of a unified reuse protocol infeasible. Finally,perspectives are presented to cater to the increased applications of L-PBF technologies for future investigations. The present state-of-the-art work can pave the way for the broad industrial applications of L-PBF by enhancing printing consistency and reducing the total costs from the perspective of powders.

Alloy design for laser powder bed fusion additive manufacturing:a critical review

Metal additive manufacturing(AM)has been extensively studied in recent decades.Despite the significant progress achieved in manufacturing complex shapes and structures,challenges such as severe cracking when using existing alloys for laser powder bed fusion(L-PBF)AM have persisted.These challenges arise because commercial alloys are primarily designed for conventional casting or forging processes,overlooking the fast cooling rates,steep temperature gradients and multiple thermal cycles of L-PBF.To address this,there is an urgent need to develop novel alloys specifically tailored for L-PBF technologies.This review provides a comprehensive summary of the strategies employed in alloy design for L-PBF.It aims to guide future research on designing novel alloys dedicated to L-PBF instead of adapting existing alloys.The review begins by discussing the features of the L-PBF processes,focusing on rapid solidification and intrinsic heat treatment.Next,the printability of the four main existing alloys(Fe-,Ni-,Al-and Ti-based alloys)is critically assessed,with a comparison of their conventional weldability.It was found that the weldability criteria are not always applicable in estimating printability.Furthermore,the review presents recent advances in alloy development and associated strategies,categorizing them into crack mitigation-oriented,microstructure manipulation-oriented and machine learning-assisted approaches.Lastly,an outlook and suggestions are given to highlight the issues that need to be addressed in future work.

Influence of heat treatment on microstructure,mechanical and corrosion behavior of WE43 alloy fabricated by laser-beam powder bed fusion

Magnesium(Mg)alloys are considered to be a new generation of revolutionary medical metals.Laser-beam powder bed fusion(PBF-LB)is suitable for fabricating metal implants withpersonalized and complicated structures.However,the as-built part usually exhibits undesirable microstructure and unsatisfactory performance.In this work,WE43 parts were firstly fabricated by PBF-LB and then subjected to heat treatment.Although a high densification rate of 99.91%was achieved using suitable processes,the as-built parts exhibited anisotropic and layeredmicrostructure with heterogeneously precipitated Nd-rich intermetallic.After heat treatment,fine and nano-scaled Mg24Y5particles were precipitated.Meanwhile,theα-Mg grainsunderwent recrystallization and turned coarsened slightly,which effectively weakened thetexture intensity and reduced the anisotropy.As a consequence,the yield strength and ultimate tensile strength were significantly improved to(250.2±3.5)MPa and(312±3.7)MPa,respectively,while the elongation was still maintained at a high level of 15.2%.Furthermore,the homogenized microstructure reduced the tendency of localized corrosion and favoredthe development of uniform passivation film.Thus,the degradation rate of WE43 parts was decreased by an order of magnitude.Besides,in-vitro cell experiments proved their favorable biocompatibility.

Microstructure evolution and strengthening mechanism of high -performance powder metallurgy TA15 titanium alloy by hot rolling

Hot deformation of sintered billets by powder metallurgy(PM)is an effective preparation technique for titanium alloys,which is more significant for high-alloying alloys.In this study,Ti–6.5Al–2Zr–Mo–V(TA15)titanium alloy plates were prepared by cold press-ing sintering combined with high-temperature hot rolling.The microstructure and mechanical properties under different process paramet-ers were investigated.Optical microscope,electron backscatter diffraction,and others were applied to characterize the microstructure evolution and mechanical properties strengthening mechanism.The results showed that the chemical compositions were uniformly dif-fused without segregation during sintering,and the closing of the matrix craters was accelerated by increasing the sintering temperature.The block was hot rolled at 1200℃ with an 80%reduction under only two passes without annealing.The strength and elongation of the plate at 20–25℃ after solution and aging were 1247 MPa and 14.0%,respectively,which were increased by 24.5%and 40.0%,respect-ively,compared with the as-sintered alloy at 1300℃.The microstructure was significantly refined by continuous dynamic recrystalliza-tion,which was completed by the rotation and dislocation absorption of the substructure surrounded by low-angle grain boundaries.After hot rolling combined with heat treatment,the strength and plasticity of PM-TA15 were significantly improved,which resulted from the dense,uniform,and fine recrystallization structure and the synergistic effect of multiple slip systems.

纳米C-S-H的合成及其对普通硅酸盐水泥早期水化的影响

为提高水泥基材料的早期强度,制备了纳米C-S-H悬浮液,并通过XRD和Zeta电位对其组成和粒度分布、稳定性进行了分析。通过水化放热、热重分析和扫描电子显微镜扫描电镜(SEM)研究了纳米C-S-H对硅酸盐水泥早期强度发展、水化放热、水化产物的影响。结果表明:合成了具有半结晶结构的稳定的纳米C-S-H悬浮液。纳米C-S-H的加入促进了C3S的水化,尤其是在前24 h,并使水泥的水化诱导期明显缩短。含有0.05%纳米C-S-H砂浆的8 h、16 h和24 h抗压强度分别提高了176.0%、145.6%和43.9%,与此同时,砂浆的3 d抗压强度没有明显减少。

Influence of layer thickness on formation quality,microstructure,mechanical properties,and corrosion resistance of WE43 magnesium alloy fabricated by laser powder bed fusion

Laser powder bed fusion(L-PBF)of Mg alloys has provided tremendous opportunities for customized production of aeronautical and medical parts.Layer thickness(LT)is of great significance to the L-PBF process but has not been studied for Mg alloys.In this study,WE43 Mg alloy bulk cubes,porous scaffolds,and thin walls with layer thicknesses of 10,20,30,and 40μm were fabricated.The required laser energy input increased with increasing layer thickness and was different for the bulk cubes and porous scaffolds.Porosity tended to occur at the connection joints in porous scaffolds for LT40 and could be eliminated by reducing the laser energy input.For thin wall parts,a large overhang angle or a small wall thickness resulted in porosity when a large layer thicknesses was used,and the porosity disappeared by reducing the layer thickness or laser energy input.A deeper keyhole penetration was found in all occasions with porosity,explaining the influence of layer thickness,geometrical structure,and laser energy input on the porosity.All the samples achieved a high fusion quality with a relative density of over 99.5%using the optimized laser energy input.The increased layer thickness resulted to more precipitation phases,finer grain sizes and decreased grain texture.With the similar high fusion quality,the tensile strength and elongation of bulk samples were significantly improved from 257 MPa and 1.41%with the 10μm layer to 287 MPa and 15.12%with the 40μm layer,in accordance with the microstructural change.The effect of layer thickness on the compressive properties of porous scaffolds was limited.However,the corrosion rate of bulk samples accelerated with increasing the layer thickness,mainly attributed to the increased number of precipitation phases.

Integrated high-performance and accurate shaping technology of low-cost powder metallurgy titanium alloys: A comprehensive review

The practical engineering applications of powder metallurgy (PM) Ti alloys produced through cold compaction and pressure-less sintering are impeded by poor sintering densification, embrittlement caused by excessive O impurities, and severe sintering deforma-tion resulting from the use of heterogeneous powder mixtures. This review presents a summary of our previous work on addressing the above challenges. Initially, we proposed a novel strategy using reaction-induced liquid phases to enhance sintering densification. Near- complete density (relative density exceeding 99%) was achieved by applying the above strategy and newly developed sintering aids. By focusing on the O-induced embrittlement issue, we determined the onset dissolution temperature of oxide films in the Ti matrix. On the basis of this finding, we established a design criterion for effective O scavengers that require reaction with oxide films before their dissol-ution. Consequently, a ductile PM Ti alloy was successfully obtained by introducing 0.3wt% NdB6 as the O scavenger. Lastly, a powder- coating strategy was adopted to address the sintering deformation issue. The ultrafine size and shell-like distribution characteristics of coating particles ensured rapid dissolution and homogeneity in the Ti matrix, thereby facilitating linear shrinkage during sintering. As a result, geometrically complex Ti alloy parts with high dimensional accuracy were fabricated by using the coated powder. Our fundament-al findings and related technical achievements enabled the development of an integrated production technology for the high-performance and accurate shaping of low-cost PM Ti alloys. Additionally, the primary engineering applications and progress in the industrialization practice of our developed technology are introduced in this review.

Role of heterogenous microstructure and deformation behavior in achieving superior strength-ductility synergy in zinc fabricated via laser powder bed fusion

Zinc(Zn)is considered a promising biodegradable metal for implant applications due to its appropriate degradability and favorable osteogenesis properties.In this work,laser powder bed fusion(LPBF)additive manufacturing was employed to fabricate pure Zn with a heterogeneous microstructure and exceptional strength-ductility synergy.An optimized processing window of LPBF was established for printing Zn samples with relative densities greater than 99%using a laser power range of 80∼90 W and a scanning speed of 900 mm s−1.The Zn sample printed with a power of 80 W at a speed of 900 mm s−1 exhibited a hierarchical heterogeneous microstructure consisting of millimeter-scale molten pool boundaries,micrometer-scale bimodal grains,and nanometer-scale pre-existing dislocations,due to rapid cooling rates and significant thermal gradients formed in the molten pools.The printed sample exhibited the highest ductility of∼12.1%among all reported LPBF-printed pure Zn to date with appreciable ultimate tensile strength(∼128.7 MPa).Such superior strength-ductility synergy can be attributed to the presence of multiple deformation mechanisms that are primarily governed by heterogeneous deformation-induced hardening resulting from the alternative arrangement of bimodal Zn grains with pre-existing dislocations.Additionally,continuous strain hardening was facilitated through the interactions between deformation twins,grains and dislocations as strain accumulated,further contributing to the superior strength-ductility synergy.These findings provide valuable insights into the deformation behavior and mechanisms underlying exceptional mechanical properties of LPBF-printed Zn and its alloys for implant applications.

Microstructure and thermal properties of dissimilar M300–CuCr1Zr alloys by multi-material laser-based powder bed fusion

Multi-material laser-based powder bed fusion (PBF-LB) allows manufacturing of parts with 3-dimensional gradient and additional functionality in a single step. This research focuses on the combination of thermally-conductive CuCr1Zr with hard M300 tool steel.Two interface configurations of M300 on CuCr1Zr and CuCr1Zr on M300 were investigated. Ultra-fine grains form at the interface due to the low mutual solubility of Cu and steel. The material mixing zone size is dependent on the configurations and tunable in the range of0.1–0.3 mm by introducing a separate set of parameters for the interface layers. Microcracks and pores mainly occur in the transition zone.Regardless of these defects, the thermal diffusivity of bimetallic parts with 50vol% of CuCr1Zr significantly increases by 70%–150%compared to pure M300. The thermal diffusivity of CuCr1Zr and the hardness of M300 steel can be enhanced simultaneously by applying the aging heat treatment.

Fabrication and characterization of multi-scale coated boron powders with improved combustion performance:A brief review

Boron has high mass and volume calorific values,but it is difficult to ignite and has low combustion efficiency.This literature review summarizes the strategies that are used to solve the above-mentioned problems,which include coatings of boron by using fluoride compounds,energetic composites,metal fuels,and metal oxides.Coating techniques include recrystallization,dual-solvent,phase transfer,electrospinning,etc.As one of the effective coating agents,the fluorine compounds can react with the oxide shell of boron powder.In comparison,the energetic composites can effectively improve the flame temperature of boron powder and enhance the evaporation efficiency of oxide film as a condensed product.Metals and metal oxides would react with boron powder to form metal borides with a lower ignition point,which could reduce its ignition temperature.

Danggui Shaoyao powder improves hepatic lipid metabolism in atherosclerosis mice via PPARγ-LXRα-ABCA1 pathway regulation

Objective:To observe the effects of Danggui Shaoyao powder(DSP)on hepatic lipid metabolism and further explore its mechanism of action by peroxisome proliferator-activated receptor(PPARγ)-liver X receptor(LXRα)-adenosine triphosphate(ATP)-binding cassette transporter A1(ABCA1)pathway regulation.Methods: Eight C57BL/6J male mice were selected as the control group,and 24 ApoE^(−/−)male mice were randomly divided into the atherosclerosis model(AS)group,atorvastatin calcium(AC)group,and DSP group(n=8 each group).To establish an AS model,ApoE^(−/−)mice were fed a high-fat diet for 16 weeks.Pathologic changes in the aortic vasculature and liver were identified using Oil Red O staining.Triglyceride(TG),cholesterol(TC),and low-density lipoprotein cholesterol(LDL-C)levels were determined in the livers using a single-reagent GPO-PAP method.Fluorescence quantitative polymerase chain reaction and western blot were used to observe and evaluate the mRNA and protein expression of the PPARγ-LXRα-ABCA1 intermediates in the liver.Results: After 16 weeks of a high-fat diet,ApoE^(−/−)mice showed more Oil Red O staining in the aorta and liver compared to the CONT group.Compared to the AS group,the DSP and AC treatment reduced aortic plaque and hepatic lipid deposition to varying degrees.Furthermore,DSP significantly reduced the hepatic lipid area in ApoE^(−/−)mice(P<.001)and decreased the levels of TG,TC,and LDL-C in liver(P<.001,P=.027,P<.001,respectively).DSP also significantly increased the levels of PPARγ,LXRα,ABCA1,and ABCG1 mRNA expression,as well as the PPARγ,LXRα,ABCA1,and ABCG1 protein expression in liver.Conclusion: DSP improved hepatic lipid metabolism via PPARγ-LXRα-ABCA1 pathway modulation for AS treatment.

Ballistic performance of titanium-based layered composites made using blended elemental powder metallurgy and hot isostatic pressing

Metal matrix composites tiles based on Ti-6Al-4V(Ti64)alloy,reinforced with 10,20,and 40(vol%)of either TiC or TiB particles were made using press-and-sinter blended elemental powder metallurgy(BEPM)and then bonded together into 3-layer laminated plates using hot isostatic pressing(HIP).The laminates were ballistically tested and demonstrated superior performance.The microstructure and properties of the laminates were analyzed to determine the effect of the BEPM and HIP processing on the ballistic properties of the layered plates.The effect of porosity in sintered composites on further diffusion bonding of the plates during HIP is analyzed to understand the bonding features at the interfaces between different adjacent layers in the laminate.Exceptional ballistic performance of fabricated structures was explained by a significant reduction in the residual porosity of the BEPM products by their additional processing using HIP,which provides an unprecedented increase in the hardness of the layered composites.It is argued that the combination of the used two technologies,BEPM and HIP is principally complimentary for the materials in question with the abilities to solve the essential problems of each used individually.

Wet tissue adhesive polymeric powder hydrogels for skeletal muscle regeneration

Volumetric muscle loss(VML)frequently results from traumatic incidents and can lead to severe functional disabilities.Hydrogels have been widely employed for VML tissue regeneration,which are unfortunately ineffective because of the lack of intimate contact with injured tissue for structural and mechanical support.Adhesive hydrogels allow for strong tissue connections for wound closure.Nevertheless,conventional adhesive hydrogels exhibit poor tissue adhesion in moist,bleeding wounds due to the hydration layer at the tissue–hydrogel interfaces,resulting in insufficient performance.In this study,we developed a novel,biocompatible,wet tissue adhesive powder hydrogel consisting of dextran-aldehyde(dex-ald)and gelatin for the regeneration of VML.This powder absorbs the interfacial tissue fluid and buffer solution on the tissue,spontaneously forms a hydrogel,and strongly adheres to the tissue via various molecular interactions,including the Schiff base reaction.In particular,the powder composition with a 1:4 ratio of dex-ald to gelatin exhibited optimal characteristics with an appropriate gelation time(258 s),strong tissue adhesion(14.5 kPa),and stability.Dex-ald/gelatin powder hydrogels presented strong adhesion to various organs and excellent hemostasis compared to other wet hydrogels and fibrin glue.A mouse VML injury model revealed that the dex-ald/gelatin powder hydrogel significantly improved muscle regeneration,reduced fibrosis,enhanced vascularization,and decreased inflammation.Consequently,our wet-adhesive powder hydrogel can serve as an effective platform for repairing various tissues,including the heart,muscle,and nerve tissues.

C-S-H凝胶无定型纳米孔隙中NaCl蒸发结晶分子动力学分析

氯化钠(NaCl)干湿循环结晶会对水泥混凝土材料产生破坏,现有试验方法存在局限性,很难从纳米尺度对盐结晶破坏机理进行研究。因此本文采用分子动力学方法,针对水泥水化主要微观产物水化硅酸钙(C-S-H)凝胶,研究NaCl在C-S-H凝胶无定型孔隙中蒸发结晶过程和结晶破坏机理。结果表明,本文构建的C-S-H凝胶无定型模型更接近于低密度的C-S-H凝胶模型,NaCl在这个模型孔隙中蒸发结晶遵循两步成核机制,蒸发结晶后的NaCl晶体填充C-S-H凝胶纳米孔隙,会显著降低C-S-H凝胶整体抗拉变形能力,使C-S-H凝胶变脆,这一结论为解释C-S-H凝胶在蒸发结晶作用下产生破坏的现象提供了依据。

Shock Raman spectra and structural transformation of powdered TKX-50 by the plate impact experiments combined with real-time Raman detection

As an energetic material of great interest,the work capacity of dihydroxylammonium 5,5’-bistetrazole-1,1’-diolate(TKX-50)has been questioned recently.Although some research groups have explored the reasons for the low working ability of TKX-50,the plane impact experiment on powdered TKX-50 is obviously closer to the practical application,and the conclusions based on this are more guiding.Hence,we performed shock Hugoniot measurements of powdered TKX-50 between 5.65 and 16.29 GPa.The plane impact experiments of powdered TKX-50 were carried out and the shocked Raman spectra were collected.By Raman spectroscopy analysis,a new peak of powdered TKX-50 was found between19.47 GPa and 24.96 GPa,which may be caused by decomposition/phase transition and was related with the low work capacity.

Fuel recycling feedback control via real-time boron powder injection in EAST with full metal wall

A feedback control of fuel recycling via real-time boron powder injection,addressing the issue of continuously increasing recycling in long-pulse plasma discharges,has been successfully developed and implemented on EAST tokamak.The feedback control system includes four main parts:the impurity powder dropper(IPD),a diagnostic system measuring fuel recycling level represented by D_(α)emission,a plasma control system(PCS)implementing the Proportional Integral Derivative(PID)algorithm,and a signal converter connecting the IPD and PCS.Based on this control system,both active control and feedback control experiments have recently been performed on EAST with a full metal wall.The experimental results show that the fuel recycling can be gradually reduced to lower level as PCS control voltage increases.In the feedback control experiments,it is also observed that the D_(α)emission is reduced to the level below the target D_(α)value by adjusting boron injection flow rate,indicating successful implementation of the fuel recycling feedback control on EAST.This technique provides a new method for fuel recycling control of long pulse and high parameter plasma operations in future fusion devices.

Lactose-free milk powder can effectively relieve diarrhea symptoms in weaning SD rats and children

Diarrhea has become the leading cause of illness and death among infants and young children in developing countries.Clinically,patients with diarrhea showed damaged intestinal epithelial villi,usually accompanied by lactase deficiency.In this study,we evaluated the therapeutic effects of lactose-free milk powder on rats and children with diarrhea.Antibiotic-associated diarrhea(AAD)model was established by gavage with antibiotic mixture in SD rats,followed by administration of milk powder containing lactose or not.The results showed that lactose-free milk powder ameliorated A AD-related diarrhea symptoms,and accelerated the recovery from diarrhea.And 16S sequencing results indicated lactose-free milk powder contributed to increase theα-andβ-diversity of intestinal flora,and restore the intestinal microbiota disorder.In conclusion,our data demonstrate that lactose-free milk powder could alleviate diarrhea by restoring gut microbiota and intestinal barrier function.

Oxygen variation in titanium powder and metal injection molding

The control of oxygen is paramount in achieving high-performance titanium(Ti)parts by powder metallurgy such as metal in-jection molding(MIM).In this study,we purposely selected the Ti and Ti-6Al-4V powders as the reference materials since these two are the most representative Ti materials in the industry.Herein,hydride-dehydride(HDH)Ti powders were pre-oxidized to examine the ef-fect of oxygen variation on the characteristics of oxide layer on the particle surface and its resultant color feature.The results indicate that the thickness and Ti oxide level(Ti^(0)→Ti^(4+))of the oxide layer on the HDH Ti powders increased as the oxygen content increased,lead-ing to the transition of color appearance from grey,brown to blue.This work aids in the powder feedstock selection at the initial stage in powder metallurgy.In addition,the development of oxygen content was comprehensively studied during the MIM process using the gas-atomized(GA)Ti-6Al-4V powders.Particularly,the oxygen variation in the form of oxide layer,the change of oxygen content in the powders,and the relevant parts were investigated during the processes of kneading,injection,debinding,and sintering.The oxygen vari-ation was mainly concentrated in the sintering stage,and the content increased with the increase of sintering temperature.The variation of oxygen content during the MIM process demonstrates the crucial role of powder feedstock and sintering stage in controlling oxygen con-tent.This work provides a piece of valuable information on oxygen detecting,control,and manipulation for the powder and processing in the industry of Ti and its alloys by powder metallurgy.