Hydrogenated amorphous carbon coatings, deposited by low pressure plasma to minimize the wear of C100 steel components, were optimized and characterized. In order to ensure good adhesion of the films to the steel surf...Hydrogenated amorphous carbon coatings, deposited by low pressure plasma to minimize the wear of C100 steel components, were optimized and characterized. In order to ensure good adhesion of the films to the steel surface, a thin Ti interlayer was deposited, by magnetron sputtering, before the plasma deposition. The chemical characterization of the deposits was performed by means of RAMAN, XPS, RBS and ERDA analysis, while nanoindentation, nanoscratch and nanowear tests allowed to estimating the tribomechanical properties of the deposits, with the aim of evaluating their scuff-resistance. It was found that the optimized plasma deposited hydrogenated amorphous carbon coatings were well adherent to C100 steel and increased more than 70% its surface hardness.展开更多
The corrosion behavior of C100 steel in simulated environments with high H2S and CO2 content was studied through high-temperature and high-pressure autoclave, and the HaS stress corrosion cracking （SSC） resistance o...The corrosion behavior of C100 steel in simulated environments with high H2S and CO2 content was studied through high-temperature and high-pressure autoclave, and the HaS stress corrosion cracking （SSC） resistance of C100 steel was evaluated by SSC tests. Scanning electron microscopy （SEM）, transmission electron microscope （TEM） and X-ray diffraction （XRD） technique were employed to characterize the corrosion products and the metal matrix. The results indicate that all of the corrosion products in this investigation are mainly composed of different types of iron sulfide such as Fe0.95S, FeS0.9, F0.985S, Fe7S8 and FeS, and the absence of iron carbonate in the corrosion scales suggests that the corrosion process is governed by H2S corrosion. The corrosion rate decreases in the initial stage and then increases with the enhancement of the temperature. There exists a minimum corrosion rate at about 110 ℃. Under the partial pressure of H2S lower than 9 MPa, the corrosion rate decreases with the increase of P112S While over 9 MPa, a higher P112S will result in a faster corrosion process. When the applied stress is 72%, 80% and 85% of actual yield strength （AYS）, all tested specimens show no crack, which reveals a superior SSC resistance.展开更多
文摘Hydrogenated amorphous carbon coatings, deposited by low pressure plasma to minimize the wear of C100 steel components, were optimized and characterized. In order to ensure good adhesion of the films to the steel surface, a thin Ti interlayer was deposited, by magnetron sputtering, before the plasma deposition. The chemical characterization of the deposits was performed by means of RAMAN, XPS, RBS and ERDA analysis, while nanoindentation, nanoscratch and nanowear tests allowed to estimating the tribomechanical properties of the deposits, with the aim of evaluating their scuff-resistance. It was found that the optimized plasma deposited hydrogenated amorphous carbon coatings were well adherent to C100 steel and increased more than 70% its surface hardness.
基金Funded by Key National Science&Technology Specific Projects(No.2008ZX05017-002)
文摘The corrosion behavior of C100 steel in simulated environments with high H2S and CO2 content was studied through high-temperature and high-pressure autoclave, and the HaS stress corrosion cracking （SSC） resistance of C100 steel was evaluated by SSC tests. Scanning electron microscopy （SEM）, transmission electron microscope （TEM） and X-ray diffraction （XRD） technique were employed to characterize the corrosion products and the metal matrix. The results indicate that all of the corrosion products in this investigation are mainly composed of different types of iron sulfide such as Fe0.95S, FeS0.9, F0.985S, Fe7S8 and FeS, and the absence of iron carbonate in the corrosion scales suggests that the corrosion process is governed by H2S corrosion. The corrosion rate decreases in the initial stage and then increases with the enhancement of the temperature. There exists a minimum corrosion rate at about 110 ℃. Under the partial pressure of H2S lower than 9 MPa, the corrosion rate decreases with the increase of P112S While over 9 MPa, a higher P112S will result in a faster corrosion process. When the applied stress is 72%, 80% and 85% of actual yield strength （AYS）, all tested specimens show no crack, which reveals a superior SSC resistance.
