The dynamic optimal interpolation(DOI)method is a technique based on quasi-geostrophic dynamics for merging multi-satellite altimeter along-track observations to generate gridded absolute dynamic topography(ADT).Compa...The dynamic optimal interpolation(DOI)method is a technique based on quasi-geostrophic dynamics for merging multi-satellite altimeter along-track observations to generate gridded absolute dynamic topography(ADT).Compared with the linear optimal interpolation(LOI)method,the DOI method can improve the accuracy of gridded ADT locally but with low computational efficiency.Consequently,considering both computational efficiency and accuracy,the DOI method is more suitable to be used only for regional applications.In this study,we propose to evaluate the suitable region for applying the DOI method based on the correlation between the absolute value of the Jacobian operator of the geostrophic stream function and the improvement achieved by the DOI method.After verifying the LOI and DOI methods,the suitable region was investigated in three typical areas:the Gulf Stream(25°N-50°N,55°W-80°W),the Japanese Kuroshio(25°N-45°N,135°E-155°E),and the South China Sea(5°N-25°N,100°E-125°E).We propose to use the DOI method only in regions outside the equatorial region and where the absolute value of the Jacobian operator of the geostrophic stream function is higher than1×10^(-11).展开更多
Missing value is one of the main factors that cause dirty data.Without high-quality data,there will be no reliable analysis results and precise decision-making.Therefore,the data warehouse needs to integrate high-qual...Missing value is one of the main factors that cause dirty data.Without high-quality data,there will be no reliable analysis results and precise decision-making.Therefore,the data warehouse needs to integrate high-quality data consistently.In the power system,the electricity consumption data of some large users cannot be normally collected resulting in missing data,which affects the calculation of power supply and eventually leads to a large error in the daily power line loss rate.For the problem of missing electricity consumption data,this study proposes a group method of data handling(GMDH)based data interpolation method in distribution power networks and applies it in the analysis of actually collected electricity data.First,the dependent and independent variables are defined from the original data,and the upper and lower limits of missing values are determined according to prior knowledge or existing data information.All missing data are randomly interpolated within the upper and lower limits.Then,the GMDH network is established to obtain the optimal complexity model,which is used to predict the missing data to replace the last imputed electricity consumption data.At last,this process is implemented iteratively until the missing values do not change.Under a relatively small noise level(α=0.25),the proposed approach achieves a maximum error of no more than 0.605%.Experimental findings demonstrate the efficacy and feasibility of the proposed approach,which realizes the transformation from incomplete data to complete data.Also,this proposed data interpolation approach provides a strong basis for the electricity theft diagnosis and metering fault analysis of electricity enterprises.展开更多
As a branch of quantum image processing,quantum image scaling has been widely studied.However,most of the existing quantum image scaling algorithms are based on nearest-neighbor interpolation and bilinear interpolatio...As a branch of quantum image processing,quantum image scaling has been widely studied.However,most of the existing quantum image scaling algorithms are based on nearest-neighbor interpolation and bilinear interpolation,the quantum version of bicubic interpolation has not yet been studied.In this work,we present the first quantum image scaling scheme for bicubic interpolation based on the novel enhanced quantum representation(NEQR).Our scheme can realize synchronous enlargement and reduction of the image with the size of 2^(n)×2^(n) by integral multiple.Firstly,the image is represented by NEQR and the original image coordinates are obtained through multiple CNOT modules.Then,16 neighborhood pixels are obtained by quantum operation circuits,and the corresponding weights of these pixels are calculated by quantum arithmetic modules.Finally,a quantum matrix operation,instead of a classical convolution operation,is used to realize the sum of convolution of these pixels.Through simulation experiments and complexity analysis,we demonstrate that our scheme achieves exponential speedup over the classical bicubic interpolation algorithm,and has better effect than the quantum version of bilinear interpolation.展开更多
In this study,a wavelet multi-resolution interpolation Galerkin method(WMIGM)is proposed to solve linear singularly perturbed boundary value problems.Unlike conventional wavelet schemes,the proposed algorithm can be r...In this study,a wavelet multi-resolution interpolation Galerkin method(WMIGM)is proposed to solve linear singularly perturbed boundary value problems.Unlike conventional wavelet schemes,the proposed algorithm can be readily extended to special node generation techniques,such as the Shishkin node.Such a wavelet method allows a high degree of local refinement of the nodal distribution to efficiently capture localized steep gradients.All the shape functions possess the Kronecker delta property,making the imposition of boundary conditions as easy as that in the finite element method.Four numerical examples are studied to demonstrate the validity and accuracy of the proposedwavelet method.The results showthat the use ofmodified Shishkin nodes can significantly reduce numerical oscillation near the boundary layer.Compared with many other methods,the proposed method possesses satisfactory accuracy and efficiency.The theoretical and numerical results demonstrate that the order of theε-uniform convergence of this wavelet method can reach 5.展开更多
The purpose of this paper is to investigate the spatial interpolation of rainfall variability with deterministic and geostatic inspections in the Prefecture of Kilkis (Greece). The precipitation data where recorded fr...The purpose of this paper is to investigate the spatial interpolation of rainfall variability with deterministic and geostatic inspections in the Prefecture of Kilkis (Greece). The precipitation data where recorded from 12 meteorological stations in the Prefecture of Kilkis for 36 hydrological years (1973-2008). The cumulative monthly values of rainfall were studied on an annual and seasonal basis as well as during the arid-dry season. In the deterministic tests, the I.D.W. and R.B.F. checks were inspected, while in the geostatic tests, Ordinary Kriging and Universal Kriging respectively. The selection of the optimum method was made based on the least Root Mean Square Error (R.M.S.E.), as well as on the Mean Error (M.E.), as assessed by the cross validation analysis. The geostatical Kriging also considered the impact of isotropy and anisotropy across all time periods of data collection. Moreover, for Universal Kriging, the study explored spherical, exponential and Gaussian models in various combinations. Geostatistical techniques consistently demonstrated greater reliability than deterministic techniques across all time periods of data collection. Specifically, during the annual period, anisotropy was the prevailing characteristic in geostatistical techniques. Moreover, the results for the irrigation and seasonal periods were generally comparable, with few exceptions where isotropic methods yielded lower (R.M.S.E.) in some seasonal observations.展开更多
This paper introduces the definition of the Orthogonal Type Node Configuration and discusses the corresponding multivariate Lagrange, Hermite and Birkhoff interpolation problems in high dimensional space R s(s>2). ...This paper introduces the definition of the Orthogonal Type Node Configuration and discusses the corresponding multivariate Lagrange, Hermite and Birkhoff interpolation problems in high dimensional space R s(s>2). This node configuration can be considered to be a kind of extension of the Cross Type Node Configuration , in R 2 to high dimensional spaces. And the Mixed Type Node Configuration in R s(s>2) is also discussed in this paper in an example.展开更多
We construct general structures of one and two variable interpolation function, without depending on the existence of divided difference or inverse differences, and we also discuss the block based osculatory interpola...We construct general structures of one and two variable interpolation function, without depending on the existence of divided difference or inverse differences, and we also discuss the block based osculatory interpolation in one variable case. Clearly, our method offers marly flexible interpolation schemes for choices. Error terms for the interpolation are determined and numerical examples are given to show the effectlveness of the results.展开更多
Randomness and fluctuations in wind power output may cause changes in important parameters(e.g.,grid frequency and voltage),which in turn affect the stable operation of a power system.However,owing to external factors...Randomness and fluctuations in wind power output may cause changes in important parameters(e.g.,grid frequency and voltage),which in turn affect the stable operation of a power system.However,owing to external factors(such as weather),there are often various anomalies in wind power data,such as missing numerical values and unreasonable data.This significantly affects the accuracy of wind power generation predictions and operational decisions.Therefore,developing and applying reliable wind power interpolation methods is important for promoting the sustainable development of the wind power industry.In this study,the causes of abnormal data in wind power generation were first analyzed from a practical perspective.Second,an improved complete ensemble empirical mode decomposition with adaptive noise(ICEEMDAN)method with a generative adversarial interpolation network(GAIN)network was proposed to preprocess wind power generation and interpolate missing wind power generation sub-components.Finally,a complete wind power generation time series was reconstructed.Compared to traditional methods,the proposed ICEEMDAN-GAIN combination interpolation model has a higher interpolation accuracy and can effectively reduce the error impact caused by wind power generation sequence fluctuations.展开更多
This paper investigates the optimal Birkhoff interpolation and Birkhoff numbers of some function spaces in space L∞[-1,1]and weighted spaces Lp,ω[-1,1],1≤p<∞,with w being a continuous integrable weight function...This paper investigates the optimal Birkhoff interpolation and Birkhoff numbers of some function spaces in space L∞[-1,1]and weighted spaces Lp,ω[-1,1],1≤p<∞,with w being a continuous integrable weight function in(-1,1).We proved that the Lagrange interpolation algorithms based on the zeros of some polynomials are optimal.We also show that the Lagrange interpolation algorithms based on the zeros of some polynomials are optimal when the function values of the two endpoints are included in the interpolation systems.展开更多
The bivariate interpolation in two dimensional space R2 is more complicated than that in one dimensional space R, because there is no Haar space of continuous functions in R2. Therefore, the bivariate interpolation ha...The bivariate interpolation in two dimensional space R2 is more complicated than that in one dimensional space R, because there is no Haar space of continuous functions in R2. Therefore, the bivariate interpolation has not a unique solution for a set of arbitrary distinct pairwise points. In this work, we suggest a type of basis which depends on the points such that the bivariate interpolation has the unique solution for any set of distinct pairwise points. In this case, the matrix of bivariate interpolation has the semi inherited factorization.展开更多
As a part of quantum image processing, quantum image scaling is a significant technology for the development of quantum computation. At present, most of the quantum image scaling schemes are based on grayscale images,...As a part of quantum image processing, quantum image scaling is a significant technology for the development of quantum computation. At present, most of the quantum image scaling schemes are based on grayscale images, with relatively little processing for color images. This paper proposes a quantum color image scaling scheme based on bilinear interpolation, which realizes the 2^(n_(1)) × 2^(n_(2)) quantum color image scaling. Firstly, the improved novel quantum representation of color digital images(INCQI) is employed to represent a 2^(n_(1)) × 2^(n_(2)) quantum color image, and the bilinear interpolation method for calculating pixel values of the interpolated image is presented. Then the quantum color image scaling-up and scaling-down circuits are designed by utilizing a series of quantum modules, and the complexity of the circuits is analyzed.Finally, the experimental simulation results of MATLAB based on the classical computer are given. The ultimate results demonstrate that the complexities of the scaling-up and scaling-down schemes are quadratic and linear, respectively, which are much lower than the cubic function and exponential function of other bilinear interpolation schemes.展开更多
High-resolution underwater digital elevation models(DEMs)are important for water and soil conservation,hydrological analysis,and river channel dredging.In this work,the underwater topography of the Panjing River in Sh...High-resolution underwater digital elevation models(DEMs)are important for water and soil conservation,hydrological analysis,and river channel dredging.In this work,the underwater topography of the Panjing River in Shanghai,China,was measured by an unmanned surface vessel.Five different interpolation methods were used to generate the underwater DEM and their precision and applicability for different underwater landforms were analyzed through cross-validation.The results showed that there was a positive correlation between the interpolation error and the terrain surface roughness.The five interpolation methods were all appropriate for the survey area,but their accuracy varied with different surface roughness.Based on the analysis results,an integrated approach was proposed to automatically select the appropriate interpolation method according to the different surface roughness in the surveying area.This approach improved the overall interpolation precision.The suggested technique provides a reference for the selection of interpolationmethods for underwater DEMdata.展开更多
In this paper, a general family of derivative-free n + 1-point iterative methods using n + 1 evaluations of the function and a general family of n-point iterative methods using n evaluations of the function and only o...In this paper, a general family of derivative-free n + 1-point iterative methods using n + 1 evaluations of the function and a general family of n-point iterative methods using n evaluations of the function and only one evaluation of its derivative are constructed by the inverse interpolation with the memory on the previous step for solving the simple root of a nonlinear equation. The order and order of convergence of them are proved respectively. Finally, the proposed methods and the basins of attraction are demonstrated by the numerical examples.展开更多
General interpolation formulae for barycentric interpolation and barycen- tric rational Hermite interpolation are established by introducing multiple parameters, which include many kinds of barycentric interpolation a...General interpolation formulae for barycentric interpolation and barycen- tric rational Hermite interpolation are established by introducing multiple parameters, which include many kinds of barycentric interpolation and barycentric rational Her- mite interpolation. We discussed the interpolation theorem, dual interpolation and special cases. Numerical example is given to show the effectiveness of the method.展开更多
In this paper, we obtain a properly posed set of nodes for interpolation on a sphere. Moreover it is applied to construct properly posed set of nodes for Lagrange interpolation on the trivariate polynomial space of to...In this paper, we obtain a properly posed set of nodes for interpolation on a sphere. Moreover it is applied to construct properly posed set of nodes for Lagrange interpolation on the trivariate polynomial space of total degree n.展开更多
In this paper, a new derivative free trust region method is developed based on the conic interpolation model for the unconstrained optimization. The conic interpolation model is built by means of the quadratic model f...In this paper, a new derivative free trust region method is developed based on the conic interpolation model for the unconstrained optimization. The conic interpolation model is built by means of the quadratic model function, the collinear scaling formula, quadratic approximation and interpolation. All the parameters in this model are determined by objective function interpolation condition. A new derivative free method is developed based upon this model and the global convergence of this new method is proved without any information on gradient.展开更多
Due to the deficiency of sliding Lagrange polynomial interpolation, the author proposes a new interpolation method, which considers the physical character of satellite movement in coordinate transformation and reasona...Due to the deficiency of sliding Lagrange polynomial interpolation, the author proposes a new interpolation method, which considers the physical character of satellite movement in coordinate transformation and reasonable selection of interpolation function. Precision of the two methods is compared by a numerical example. The result shows that the new method is superior to the sliding Lagrange polynomial interpolation in interpolation and extrapolation, especially in extrapolation that is over short time spans.展开更多
In this paper, we use a univariate multiquadric quasi-interpolation scheme to solve the one-dimensional nonlinear sine-Gordon equation that is related to many physical phenomena. We obtain a numerical scheme by using ...In this paper, we use a univariate multiquadric quasi-interpolation scheme to solve the one-dimensional nonlinear sine-Gordon equation that is related to many physical phenomena. We obtain a numerical scheme by using the derivative of the quasi-interpolation to approximate the spatial derivative and a difference scheme to approximate the temporal derivative. The advantage of the obtained scheme is that the algorithm is very simple so that it is very easy to implement. The results of numerical experiments are presented and compared with analytical solutions to confirm the good accuracy of the presented scheme.展开更多
With Newton's interpolating formula, we construct a kind of block based Newton-like blending osculatory interpolation.The interpolation provides us many flexible interpolation schemes for choices which include the ex...With Newton's interpolating formula, we construct a kind of block based Newton-like blending osculatory interpolation.The interpolation provides us many flexible interpolation schemes for choices which include the expansive Newton's polynomial inter- polation as its special case. A bivariate analogy is also discussed and numerical examples are given to show the effectiveness of the interpolation.展开更多
Aiming at the problem of low accuracy of interpolation error calculation of existing NURBS curves, an approximate method for the distance between a point and a NURBS interpolation curve is proposed while satisfying th...Aiming at the problem of low accuracy of interpolation error calculation of existing NURBS curves, an approximate method for the distance between a point and a NURBS interpolation curve is proposed while satisfying the accuracy of the solution. Firstly, the minimum parameter interval of the node vector corresponding to the data point under test in the original data point sequence is determined, and the parameter interval is subdivided according to the corresponding step size, and the corresponding parameter value is obtained. Secondly, the distance from the measured point to the NURBS curve is calculated, and the nearest distance is found out. The node interval is subdivided again on one side of the nearest distance. Finally, the distance between the data point to be measured and each subdivision point is calculated again, and the minimum distance is taken as the interpolation error between the point and the NURBS curve. The simulation results of actual tool position data show that this method can more accurately obtain the error of spatial NURBS interpolation curve.展开更多
基金supported by National Natural Science Foundation of China under Grants 42192531 and 42192534the Special Fund of Hubei Luojia Laboratory(China)under Grant 220100001the Natural Science Foundation of Hubei Province for Distinguished Young Scholars(China)under Grant 2022CFA090。
文摘The dynamic optimal interpolation(DOI)method is a technique based on quasi-geostrophic dynamics for merging multi-satellite altimeter along-track observations to generate gridded absolute dynamic topography(ADT).Compared with the linear optimal interpolation(LOI)method,the DOI method can improve the accuracy of gridded ADT locally but with low computational efficiency.Consequently,considering both computational efficiency and accuracy,the DOI method is more suitable to be used only for regional applications.In this study,we propose to evaluate the suitable region for applying the DOI method based on the correlation between the absolute value of the Jacobian operator of the geostrophic stream function and the improvement achieved by the DOI method.After verifying the LOI and DOI methods,the suitable region was investigated in three typical areas:the Gulf Stream(25°N-50°N,55°W-80°W),the Japanese Kuroshio(25°N-45°N,135°E-155°E),and the South China Sea(5°N-25°N,100°E-125°E).We propose to use the DOI method only in regions outside the equatorial region and where the absolute value of the Jacobian operator of the geostrophic stream function is higher than1×10^(-11).
基金This research was funded by the National Nature Sciences Foundation of China(Grant No.42250410321).
文摘Missing value is one of the main factors that cause dirty data.Without high-quality data,there will be no reliable analysis results and precise decision-making.Therefore,the data warehouse needs to integrate high-quality data consistently.In the power system,the electricity consumption data of some large users cannot be normally collected resulting in missing data,which affects the calculation of power supply and eventually leads to a large error in the daily power line loss rate.For the problem of missing electricity consumption data,this study proposes a group method of data handling(GMDH)based data interpolation method in distribution power networks and applies it in the analysis of actually collected electricity data.First,the dependent and independent variables are defined from the original data,and the upper and lower limits of missing values are determined according to prior knowledge or existing data information.All missing data are randomly interpolated within the upper and lower limits.Then,the GMDH network is established to obtain the optimal complexity model,which is used to predict the missing data to replace the last imputed electricity consumption data.At last,this process is implemented iteratively until the missing values do not change.Under a relatively small noise level(α=0.25),the proposed approach achieves a maximum error of no more than 0.605%.Experimental findings demonstrate the efficacy and feasibility of the proposed approach,which realizes the transformation from incomplete data to complete data.Also,this proposed data interpolation approach provides a strong basis for the electricity theft diagnosis and metering fault analysis of electricity enterprises.
基金Project supported by the Scientific Research Fund of Hunan Provincial Education Department,China (Grant No.21A0470)the Natural Science Foundation of Hunan Province,China (Grant No.2023JJ50268)+1 种基金the National Natural Science Foundation of China (Grant Nos.62172268 and 62302289)the Shanghai Science and Technology Project,China (Grant Nos.21JC1402800 and 23YF1416200)。
文摘As a branch of quantum image processing,quantum image scaling has been widely studied.However,most of the existing quantum image scaling algorithms are based on nearest-neighbor interpolation and bilinear interpolation,the quantum version of bicubic interpolation has not yet been studied.In this work,we present the first quantum image scaling scheme for bicubic interpolation based on the novel enhanced quantum representation(NEQR).Our scheme can realize synchronous enlargement and reduction of the image with the size of 2^(n)×2^(n) by integral multiple.Firstly,the image is represented by NEQR and the original image coordinates are obtained through multiple CNOT modules.Then,16 neighborhood pixels are obtained by quantum operation circuits,and the corresponding weights of these pixels are calculated by quantum arithmetic modules.Finally,a quantum matrix operation,instead of a classical convolution operation,is used to realize the sum of convolution of these pixels.Through simulation experiments and complexity analysis,we demonstrate that our scheme achieves exponential speedup over the classical bicubic interpolation algorithm,and has better effect than the quantum version of bilinear interpolation.
基金supported by the National Natural Science Foundation of China (No.12172154)the 111 Project (No.B14044)+1 种基金the Natural Science Foundation of Gansu Province (No.23JRRA1035)the Natural Science Foundation of Anhui University of Finance and Economics (No.ACKYC20043).
文摘In this study,a wavelet multi-resolution interpolation Galerkin method(WMIGM)is proposed to solve linear singularly perturbed boundary value problems.Unlike conventional wavelet schemes,the proposed algorithm can be readily extended to special node generation techniques,such as the Shishkin node.Such a wavelet method allows a high degree of local refinement of the nodal distribution to efficiently capture localized steep gradients.All the shape functions possess the Kronecker delta property,making the imposition of boundary conditions as easy as that in the finite element method.Four numerical examples are studied to demonstrate the validity and accuracy of the proposedwavelet method.The results showthat the use ofmodified Shishkin nodes can significantly reduce numerical oscillation near the boundary layer.Compared with many other methods,the proposed method possesses satisfactory accuracy and efficiency.The theoretical and numerical results demonstrate that the order of theε-uniform convergence of this wavelet method can reach 5.
文摘The purpose of this paper is to investigate the spatial interpolation of rainfall variability with deterministic and geostatic inspections in the Prefecture of Kilkis (Greece). The precipitation data where recorded from 12 meteorological stations in the Prefecture of Kilkis for 36 hydrological years (1973-2008). The cumulative monthly values of rainfall were studied on an annual and seasonal basis as well as during the arid-dry season. In the deterministic tests, the I.D.W. and R.B.F. checks were inspected, while in the geostatic tests, Ordinary Kriging and Universal Kriging respectively. The selection of the optimum method was made based on the least Root Mean Square Error (R.M.S.E.), as well as on the Mean Error (M.E.), as assessed by the cross validation analysis. The geostatical Kriging also considered the impact of isotropy and anisotropy across all time periods of data collection. Moreover, for Universal Kriging, the study explored spherical, exponential and Gaussian models in various combinations. Geostatistical techniques consistently demonstrated greater reliability than deterministic techniques across all time periods of data collection. Specifically, during the annual period, anisotropy was the prevailing characteristic in geostatistical techniques. Moreover, the results for the irrigation and seasonal periods were generally comparable, with few exceptions where isotropic methods yielded lower (R.M.S.E.) in some seasonal observations.
文摘This paper introduces the definition of the Orthogonal Type Node Configuration and discusses the corresponding multivariate Lagrange, Hermite and Birkhoff interpolation problems in high dimensional space R s(s>2). This node configuration can be considered to be a kind of extension of the Cross Type Node Configuration , in R 2 to high dimensional spaces. And the Mixed Type Node Configuration in R s(s>2) is also discussed in this paper in an example.
基金The Grant (11RC05) of Scienti/fic Research Foundation for Talents of Hefei Universitythe Grant (11KY06ZR) of Scientific Research Foundation Hefei University+1 种基金the Key Project Foundation (KJ2008A027) of the Department of Education of Anhui Provincethe Project Foundation (KJ2010B182,KJ2011B152, KJ2011B137) of the Department of Education of Anhui Province
文摘We construct general structures of one and two variable interpolation function, without depending on the existence of divided difference or inverse differences, and we also discuss the block based osculatory interpolation in one variable case. Clearly, our method offers marly flexible interpolation schemes for choices. Error terms for the interpolation are determined and numerical examples are given to show the effectlveness of the results.
基金We gratefully acknowledge the support of National Natural Science Foundation of China(NSFC)(Grant No.51977133&Grant No.U2066209).
文摘Randomness and fluctuations in wind power output may cause changes in important parameters(e.g.,grid frequency and voltage),which in turn affect the stable operation of a power system.However,owing to external factors(such as weather),there are often various anomalies in wind power data,such as missing numerical values and unreasonable data.This significantly affects the accuracy of wind power generation predictions and operational decisions.Therefore,developing and applying reliable wind power interpolation methods is important for promoting the sustainable development of the wind power industry.In this study,the causes of abnormal data in wind power generation were first analyzed from a practical perspective.Second,an improved complete ensemble empirical mode decomposition with adaptive noise(ICEEMDAN)method with a generative adversarial interpolation network(GAIN)network was proposed to preprocess wind power generation and interpolate missing wind power generation sub-components.Finally,a complete wind power generation time series was reconstructed.Compared to traditional methods,the proposed ICEEMDAN-GAIN combination interpolation model has a higher interpolation accuracy and can effectively reduce the error impact caused by wind power generation sequence fluctuations.
基金supported by National Natural Science Foundation of China(11871006,11671271)。
文摘This paper investigates the optimal Birkhoff interpolation and Birkhoff numbers of some function spaces in space L∞[-1,1]and weighted spaces Lp,ω[-1,1],1≤p<∞,with w being a continuous integrable weight function in(-1,1).We proved that the Lagrange interpolation algorithms based on the zeros of some polynomials are optimal.We also show that the Lagrange interpolation algorithms based on the zeros of some polynomials are optimal when the function values of the two endpoints are included in the interpolation systems.
文摘The bivariate interpolation in two dimensional space R2 is more complicated than that in one dimensional space R, because there is no Haar space of continuous functions in R2. Therefore, the bivariate interpolation has not a unique solution for a set of arbitrary distinct pairwise points. In this work, we suggest a type of basis which depends on the points such that the bivariate interpolation has the unique solution for any set of distinct pairwise points. In this case, the matrix of bivariate interpolation has the semi inherited factorization.
基金the National Natural Science Foundation of China (Grant No. 6217070290)Shanghai Science and Technology Project (Grant Nos. 21JC1402800 and 20040501500)。
文摘As a part of quantum image processing, quantum image scaling is a significant technology for the development of quantum computation. At present, most of the quantum image scaling schemes are based on grayscale images, with relatively little processing for color images. This paper proposes a quantum color image scaling scheme based on bilinear interpolation, which realizes the 2^(n_(1)) × 2^(n_(2)) quantum color image scaling. Firstly, the improved novel quantum representation of color digital images(INCQI) is employed to represent a 2^(n_(1)) × 2^(n_(2)) quantum color image, and the bilinear interpolation method for calculating pixel values of the interpolated image is presented. Then the quantum color image scaling-up and scaling-down circuits are designed by utilizing a series of quantum modules, and the complexity of the circuits is analyzed.Finally, the experimental simulation results of MATLAB based on the classical computer are given. The ultimate results demonstrate that the complexities of the scaling-up and scaling-down schemes are quadratic and linear, respectively, which are much lower than the cubic function and exponential function of other bilinear interpolation schemes.
基金supported by the NationalNatural Science Foundation of China(Grant No.42102318)the Program for Professor of Special Appointment(Eastern Scholar)at Shanghai Institutions of Higher Learning.
文摘High-resolution underwater digital elevation models(DEMs)are important for water and soil conservation,hydrological analysis,and river channel dredging.In this work,the underwater topography of the Panjing River in Shanghai,China,was measured by an unmanned surface vessel.Five different interpolation methods were used to generate the underwater DEM and their precision and applicability for different underwater landforms were analyzed through cross-validation.The results showed that there was a positive correlation between the interpolation error and the terrain surface roughness.The five interpolation methods were all appropriate for the survey area,but their accuracy varied with different surface roughness.Based on the analysis results,an integrated approach was proposed to automatically select the appropriate interpolation method according to the different surface roughness in the surveying area.This approach improved the overall interpolation precision.The suggested technique provides a reference for the selection of interpolationmethods for underwater DEMdata.
文摘In this paper, a general family of derivative-free n + 1-point iterative methods using n + 1 evaluations of the function and a general family of n-point iterative methods using n evaluations of the function and only one evaluation of its derivative are constructed by the inverse interpolation with the memory on the previous step for solving the simple root of a nonlinear equation. The order and order of convergence of them are proved respectively. Finally, the proposed methods and the basins of attraction are demonstrated by the numerical examples.
基金supported by the grant of Key Scientific Research Foundation of Education Department of Anhui Province, No. KJ2014A210
文摘General interpolation formulae for barycentric interpolation and barycen- tric rational Hermite interpolation are established by introducing multiple parameters, which include many kinds of barycentric interpolation and barycentric rational Her- mite interpolation. We discussed the interpolation theorem, dual interpolation and special cases. Numerical example is given to show the effectiveness of the method.
文摘In this paper, we obtain a properly posed set of nodes for interpolation on a sphere. Moreover it is applied to construct properly posed set of nodes for Lagrange interpolation on the trivariate polynomial space of total degree n.
基金This work was supported by the National Natural Science Foundation of China(10071037)
文摘In this paper, a new derivative free trust region method is developed based on the conic interpolation model for the unconstrained optimization. The conic interpolation model is built by means of the quadratic model function, the collinear scaling formula, quadratic approximation and interpolation. All the parameters in this model are determined by objective function interpolation condition. A new derivative free method is developed based upon this model and the global convergence of this new method is proved without any information on gradient.
基金supported by the PhD Excellence Fund of Information Engineering University(S201307)
文摘Due to the deficiency of sliding Lagrange polynomial interpolation, the author proposes a new interpolation method, which considers the physical character of satellite movement in coordinate transformation and reasonable selection of interpolation function. Precision of the two methods is compared by a numerical example. The result shows that the new method is superior to the sliding Lagrange polynomial interpolation in interpolation and extrapolation, especially in extrapolation that is over short time spans.
基金supported by the State Key Development Program for Basic Research of China (Grant No 2006CB303102)Science and Technology Commission of Shanghai Municipality,China (Grant No 09DZ2272900)
文摘In this paper, we use a univariate multiquadric quasi-interpolation scheme to solve the one-dimensional nonlinear sine-Gordon equation that is related to many physical phenomena. We obtain a numerical scheme by using the derivative of the quasi-interpolation to approximate the spatial derivative and a difference scheme to approximate the temporal derivative. The advantage of the obtained scheme is that the algorithm is very simple so that it is very easy to implement. The results of numerical experiments are presented and compared with analytical solutions to confirm the good accuracy of the presented scheme.
基金Supported by the Key Project Foundation of the Department of Education of Anhui Province(No.KJ2008A027)the Project Foundation of the Department of Education of Anhui Province(No.KJ2010B182)
文摘With Newton's interpolating formula, we construct a kind of block based Newton-like blending osculatory interpolation.The interpolation provides us many flexible interpolation schemes for choices which include the expansive Newton's polynomial inter- polation as its special case. A bivariate analogy is also discussed and numerical examples are given to show the effectiveness of the interpolation.
文摘Aiming at the problem of low accuracy of interpolation error calculation of existing NURBS curves, an approximate method for the distance between a point and a NURBS interpolation curve is proposed while satisfying the accuracy of the solution. Firstly, the minimum parameter interval of the node vector corresponding to the data point under test in the original data point sequence is determined, and the parameter interval is subdivided according to the corresponding step size, and the corresponding parameter value is obtained. Secondly, the distance from the measured point to the NURBS curve is calculated, and the nearest distance is found out. The node interval is subdivided again on one side of the nearest distance. Finally, the distance between the data point to be measured and each subdivision point is calculated again, and the minimum distance is taken as the interpolation error between the point and the NURBS curve. The simulation results of actual tool position data show that this method can more accurately obtain the error of spatial NURBS interpolation curve.