CBN/Cu-Sn-Ti(CBN: cubic boron nitride) composites are prepared by active brazing sintering at 1123 K,1173 K, 1223 K and 1273 K, respectively. The effects of brazing temperature on the wettability, interfacial characte...CBN/Cu-Sn-Ti(CBN: cubic boron nitride) composites are prepared by active brazing sintering at 1123 K,1173 K, 1223 K and 1273 K, respectively. The effects of brazing temperature on the wettability, interfacial characteristics, and elemental distribution variations are fully investigated. When the brazing temperature is below 1223 K, completely uncoated and/or partially coated CBN particles with sharp edges can still be observed, and the reaction layer, mainly composed of Ti N and Ti B2, appears to be thin and uneven.When the brazing temperature is 1223 K, all CBN particles are completely coated, suggesting that adequate wetting has taken place. Besides, as Ti diffuses thoroughly and enriches the interface, the reaction layer, filled primarily by Ti N, Ti B2 and Ti B, becomes thicker(about 1.30 μm), more uniform, stable and continuous. Further increasing the temperature to 1273 K is unnecessary or even harmful as the reaction layer thickness undergoes negligible change yet some tiny micro-cracks appear on the interface, which may likely deteriorate the grinding capability of the final brazing products.展开更多
In order to develop the high-efficiency and precision machining technique of TiCp/Ti - 6Al-4V particulate reinforced titanium matrix composites （PTMCs）, high-speed grinding experiments were conducted using the singl...In order to develop the high-efficiency and precision machining technique of TiCp/Ti - 6Al-4V particulate reinforced titanium matrix composites （PTMCs）, high-speed grinding experiments were conducted using the single-layer electroplated cubic boron nitride （CBN） wheel and brazed CBN wheel, respectively. The comparative grinding performance was studied in terms of grinding force, grinding temperature, grinding-induced surface features and defects. The results display that the grinding forces and grinding temperature obtained with the brazed CBN wheel are always lower than those with the electroplated CBN wheel. Though the voids and microcracks are the dominant grinding-induced surface defects, the brazed CBN wheel produces less surface defects compared to the electroplated wheel according to the statistical analysis results. The max mum materials removal rate with the brazed CBN wheel is much higher than that with the electroplated one. All above indicate that the single-layer brazed CBN super-abrasive wheel is more suitable for high-speed grinding of PTMCs than the electroplated counterpart.展开更多
基金supported financially by the National Natural Science Foundation of China (Nos. 51622401, 51628402, 51861130361, 51861145312 and 51850410522)the Newton Advanced Fellowship by Royal Society (No. RP12G0414)+3 种基金the Research Fund for Central Universities (No. N172502004)the National Key Research and Development Program of China (No.2016YFB0300602)the Global Talents Recruitment Program endowed by the Chinese GovernmentState Key Laboratory of Solidification Processing, Northwestern Polytechnical University (No. SKLSP201805)
文摘CBN/Cu-Sn-Ti(CBN: cubic boron nitride) composites are prepared by active brazing sintering at 1123 K,1173 K, 1223 K and 1273 K, respectively. The effects of brazing temperature on the wettability, interfacial characteristics, and elemental distribution variations are fully investigated. When the brazing temperature is below 1223 K, completely uncoated and/or partially coated CBN particles with sharp edges can still be observed, and the reaction layer, mainly composed of Ti N and Ti B2, appears to be thin and uneven.When the brazing temperature is 1223 K, all CBN particles are completely coated, suggesting that adequate wetting has taken place. Besides, as Ti diffuses thoroughly and enriches the interface, the reaction layer, filled primarily by Ti N, Ti B2 and Ti B, becomes thicker(about 1.30 μm), more uniform, stable and continuous. Further increasing the temperature to 1273 K is unnecessary or even harmful as the reaction layer thickness undergoes negligible change yet some tiny micro-cracks appear on the interface, which may likely deteriorate the grinding capability of the final brazing products.
基金the financial support for this work by the National Natural Science Foundation of China (No.51235004 and No.51375235)the Fundamental Research Funds for the Central Universities (No.NE2014103)the Science and Technology Supporting Program of Jiangsu Province (No.BE2013109 and No.BY2014003-008)
文摘In order to develop the high-efficiency and precision machining technique of TiCp/Ti - 6Al-4V particulate reinforced titanium matrix composites （PTMCs）, high-speed grinding experiments were conducted using the single-layer electroplated cubic boron nitride （CBN） wheel and brazed CBN wheel, respectively. The comparative grinding performance was studied in terms of grinding force, grinding temperature, grinding-induced surface features and defects. The results display that the grinding forces and grinding temperature obtained with the brazed CBN wheel are always lower than those with the electroplated CBN wheel. Though the voids and microcracks are the dominant grinding-induced surface defects, the brazed CBN wheel produces less surface defects compared to the electroplated wheel according to the statistical analysis results. The max mum materials removal rate with the brazed CBN wheel is much higher than that with the electroplated one. All above indicate that the single-layer brazed CBN super-abrasive wheel is more suitable for high-speed grinding of PTMCs than the electroplated counterpart.
