Bearing capacity and mechanical behavior of CFG pile composite foundation

CFG pile (i.e., pile constructed by granular materials of cement, fly-ash and gravel) composite foundation is applied in subsoil treatment widely and successfully. In order to have a further study of this kind of subsoil treatment technology, the influencing factors and calculation methods of the vertical bearing capacity of single CFG pile and the CFG pile composite foundation were discussed respectively. And based on the obtained solutions, effects by the cushion and measurements to reduce negative friction area were analyzed. Moreover, the developing law of settlement and bearing capacity eigenvalue controlled by the material strength with the increase of load were given for the CFG composite foundation. The in-situ static load test was tested for CFG pile. The results of test show that the maximum test load or half of the ultimate load is used from all the points of test, the average bearing capacity eigenvalue of single pile is 390 kN, and slightly greater than the design value of bearing capacity. The bearing capacity eigenvalues of composite foundation for 3 piles are greater than 300 kPa, and the mechanical properties of CFG pile composite foundation are almost identical in the case of the same load and cushion thickness. The pile-soil stress ratio and the load-sharing ratio can be adjusted through setting up cushion thickness.

Consolidation analysis of composite foundation with partially penetrated cement fly-ash gravel(CFG) piles under changing permeable boundary conditions

Based on the double-layered foundation theory, the composite ground with partially penetrated cement fly-ash gravel(CFG) piles was regarded as a double-layered foundation including the surface reinforced area and the underlying untreated stratum. Due to the changing permeability property of CFG piles, the whole consolidation process of the composite ground with CFG piles was divided into two stages, i.e., the early stage(permeable CFG pile bodies) and the later stage(impermeable pile bodies). Then, the consolidation equation of the composite foundation with CFG piles was established by using the Terzaghi one-dimensional consolidation theory. Consequently, the unified formula to calculate the excess pore water pressure was derived with the specific solutions for the consolidation degree of composite ground, reinforced area and underlying stratum under instant load obtained respectively. Finally, combined with a numerical example, influencing rules by main factors(including the replacement rate m, the treatment depth h1, the permeability coefficient Ks1, Kv2 and compression modulus Es1, Es2 of reinforced area and underlying stratum) on the consolidation property of composite ground with CFG piles were discussed in detail. The result shows that the consolidation velocity of underlying stratum is slower than that of the reinforced area. However, the consolidation velocity of underlying stratum is slow at first then fast as a result of the transferring of effective stress to the underlying stratum during the dissipating process of excess pore water pressure.

Experimental Study of Dynamic Characteristics on Composite Foundation with CFG Long Pile and Rammed Cement-Soil Short Pile

Based on the idea of optimization design of pile type, the two kinds of the typical pile type are selected, which containing flexibility pile (e.g. rammed cement-soil pile is for short RCSP), and rigid pile (e.g. cement-flyash-gravel pile is for short CFGP). The three kinds of the composite foundation are designed, which are CFGP, CFG long pile and CFG short pile (for short CFGLP-CFGSP), CFG long-short pile and rammed cement-soil short pile (for short CFGLP-RCSSP). Natural earthquake is simulated by using the engineering blasting;the dynamic characteristics and dynamic response of the composite foundation are studied through field test. CFGLP-RCSSP is closed to linear relation. The bearing capacity of the four composite foundation of the CFGP, CFGLP-CFGSP, and CFGLP-RCSSP in the site are 225 kPa, 179 kPa, and 197 kPa, separately increases 150%, 98.8% and 119% compared to the natural foundation. The vibration main frequency is mainly depended on properties of foundation soil and piles between vibration source and measuring point, pilling load value. Horizontal vibration main frequency greater than the vertical vibration main frequency and the vertical vibration main frequency close to the first-order natural frequency of composite foundation. With the pilling load increasing, the CFGLP-RCSSP pile composite foundation combined frequency decreased. Under the same blast energy, the acceleration peak on the CFG pile composite foundation is less than CFGLP-CFGSP the corresponding values, as the load increases, the peak acceleration gently. CFG pile composite foundation is favorable on seismic. The distribution of peak acceleration is consistent within 4 m from pile top in the CFGLP_RCSSP composite foundation. The maximum of the horizontal acceleration peak along the pile body occurs at a distance of pile top 4 m or the pile top, and that of vertical acceleration peak occurred at a pile top.

Settlement Characteristics of Cement Fly-Ash GravelPile-Plate Composite Foundation of High-Speed Railway

Field tests on settlement characteristics were carried out on the cement fly-ash gravel （CFG） pile-plate composite foundation on Beijing-Xuzhou section of Beijing-Shanghai high-speed railway. The settlements of the piles and the soil between pries were measured and analyzed. The results show that the settlement-time dependency experienced three phases： rapid development phase, stable development phase and stable phase. Therefore, surcharge preloading was necessary to reduce the settlement after construction. The finite element software Plaxis was used to calculate the deformations of the pile top and the soil between piles at the embankment center, as well as the settlements of CFG pile reinforcement area and the underlying stratum under surcharge preloading. The calculation results and the field test results were compared and analyzed. Both the results show that the settlement of the composite foundation mainly occured in underlying stratum. The settlement characteristics of pile-plate composite foundation under high embankment are also concluded.

Experiments of Multi-element Composite Foundation with Steel Pipe Pile and Gravel Pile

A set of serf-developed apparatus for foundation physical model were utilized to conduct model tests of the multi-element composite foundation with a steel pipe pile and several gravel piles. Some load-bearing characteristics of the multi-element Composite foundation, including the curves of foundation settlement, stresses of piles, pile-soil stress ratio, and load-sharing ratio of piles and soil, were obtained to study its working performances in silty sand soil. The experimental results revealed that the multi-element composite foundation with steel pipe pile and gravel pile contributed more than the gravel pile composite foundation in improving the bearing capacity of the silty fine sand.

Application of CFG Pile Construction Technology for Soft Foundation Treatment

CFG pile has been widely applied as one of the common ground treatment techniques. As a concealed work, the construction quality of pile foundation not only relates to the success of the project, but also concerns the benefits of thousands of hot, seholds. Only strengthening the supervision and management during the construction and strictly designing and specifying CFG pile can ensure the construction quality of CFG pile. But most researches focus on operating mechanism and theoretical analysis, and there are fewer researches about the construction of CFG pile. The real construction of CFG pile has no specified operation and lacks of the construction guidance, which not only causes great problems and has great influence on the intensity of CFG pile, but also makes the real pile body have great difference from the design requirements. Therefore, the study on construction of CFG pile in the paper has great significance.

Deformation and failure modes of composite foundation with sub-embankment plain concrete piles

With the development of high-speed railway in China, composite foundation with rigid piles has become a stamdard solution of meeting the high requirements of stability and post-construction settlement of embankment on soft subgrade. Among several im- provement pattems, plain concrete piles have been extensively used to treat soft ground supported embankment. To investigate the deformation and failure modes of unimproved soft ground and soft ground reinforced by sub-embankment plain concrete piles, and to learn the influences of track and vehicle load, the effect of pile spacing, as well as the compression moduli of soil layers and upper load condition on the failure modes, a series of centrifuge model tests were performed. Test results indicate that the dis- placement of unimproved soft ground under the embankment increases continuously as embankment, track and train loading, and slip circle failure takes place. The deformation law of soft ground reinforced by sub-embankment plain concrete piles depends on pile spacing, compression modulus of the soft ground, and loading conditions. It was also found that plain concrete piles show displacement and failure patterns depending on its location, compression modulus of soft soil around the pile, and loading condi- tions. Furthermore, the evaluation of improved ground stability as well as the model test procedure is also presented.

The Dynamic Characteristic Experimental Method on the Composite Foundation with Rigid-Flexible Compound Piles

Based on the idea of optimization design of pile type, the composite foundations, which include cememt-flyash-gaavel (for short CFG) long piles and cement-soil (for short CS) short piles, and CS piles with CFG core as well, are formed. The method of the site dynamic characteristic tests of the composite foundations is discussed. The test results show that fireworks bomb may replace demolitions as the vibration resource. Vibration time is about 0.1 sec. Horizontal vibration major frequency is at 22.476 - 56.436 Hz, and vertical vibration major frequency is at 15.538 - 55.884 Hz. The pile arrangements of the composite foundation in the same site have more effect on the acceleration peak value. From the point of vibration, the anti-seismic effect of the CS piles with CFG core is better than others.

Numerical Analysis of the Settlement of Composite Foundation Reinforced with Crushed Stone Grouting Pile and Rigid Bearing Plate

This paper deals with a new type of crushed stone grouting pile with a rigid bearing plate. The load transfer characteristics were analyzed, and a settlement model of the composite foundation reinforced with crushed stone grouting pile and rigid bearing plate was built by FEM program. The effects of replacement ratio of capping plate, replacement ratio of pile, replacement ratio of grout diffusion zone, pile-soil modulus ratio, and serous-soil modulus ratio, on the composite foundation settlement were discussed. It is concluded that the proposed crushed stone grouting pile with a rigid bearing plate is effective in decreasing the settlement of composite foundation.

Settlement of composite foundation with discrete material pile considering modulus change

Based on deeply discussing the deformation mechanism of composite foundation with discrete material pile, firstly, the settlement of composite foundation in rigid foundation conditions was assumed to consist of two parts, an expanding part and an un-expanding part. Then, in view of the differences of deformation properties between the expanding part and the un-expanding part, the relationships between the pile modulus and the applied load in these two parts were respectively developed. Thirdly, by introducing the above relationships into settlement analysis, a new method to calculate displacement of composite foundation with discrete material pile was proposed by using the multi-stage loading theory and the layer-wise summation approach. This method is effective not only for accounting for the effect of variations of pores on deformation modulus of the pile body in different depths, but also for describing the characteristics of different deformation mechanisms of the pile body with varying depth. Finally, the proposed method was used to a practical composite foundation problem, whose theoretical results were presented and compared to those of other methods. The rationality and feasibility of this method are identified through comparative analysis.

Calculation method of composite foundation sedimentation of grouting pile with cover plate under embankment load

Grouting pile is a new soft soil foundation treatment method with characteristics such as no vibration, no noise, no soil compaction, light construction machines and quick construction velocity and so on. At present, study on reinforcement mechanism and design calculation method of composite foundation of grouting pile is initially started without design specifications, so it is usually required to draw on design specifications of stump pile when designing composite foundation of grouting pile while grouting pile has its characteristics and difference although reinforcement mechanisms and construction processes of two types of piles are similar. Sedimentation formula of composite foundation of grouting pile with cover plate is educed and a suitable deformation mode is proposed by aiming to deformation characteristics of composite foundation of grouting pile with cover plate under embankment load on basis of relevant sedimentation theories of composite foundation by combination of characteristics of composite foundation of grouting pile. The sedimentation calculation formula of grouting pile with cover plate under embankment load is educed according to balance relation of force and displacement coordination conditions by elastic theory and sedimentation calculation model established is validated by sedimentation monitoring documents of one expressway in China.

Verification of Seismic Performance of Pile Foundation in Composite Ground through Experimental and Numerical Methods

A new construction method of pile foundation in composite ground, in which, prior to installing piles, the ground is improved around the heads of the piles in soft ground or ground subject to liquefaction, which is introduced in this paper. This construction method uses a combination of pile foundation construction together with common ground improvement methods, including deep mixing, preloading and sand compaction piling, and it is referred to as the composite ground pile method. Since an artificial ground with relatively high rigidity comparing with that of the original ground was formed around the pile in this method, and the seismic performance has not been made clear, thus the seismic performance of piles in composite ground was systematically analyzed through a series of centrifuge model tests and numerical analyses by using dynamic nonlinear finite element method, and a verification method for the seismic performance of piles in composite ground was proposed on the basis of the experimental and numerical results.

Parameter analysis of composite pile foundation in bridge foundation

In the current theory of bridge foundation design,all of the loads above the cap are loaded by the pile,and the bearing capacity of the soil among piles is not taken into account.In order to analyze the bearing capacity of the soil among piles in bridge pile foundation,a model of pile foundation is established based on a bridge foundation which is under construction,and by the finite element analysis software ANSYS.According to the results of finite element analysis(FEA)and current bridge foundation design theory,a feasible composite pile foundation which can be applied in the design of bridge foundation,is recommended.Additionally,a number of modifications are made to the original design.It was confirmed that these modifications derived from numerical simulations can improve the performance of the foundation.

重载码头堆场CFG桩网复合地基离心模型试验研究

CFG桩网复合地基广泛应用于处理软土地基。采用土工离心模型试验研究某码头堆场超大荷载下CFG桩网复合地基的变形和桩土应力特性,试验模拟了地基、CFG桩、树根桩、加筋垫层、防尘网和轨道梁基础、矿石堆载等,分析了超大荷载作用下复合地基表面变形、桩顶轴力、桩间土压力、桩土应力比的变化规律。试验结果表明,复合地基的沉降速率在稳定控制标准之内,沉降量满足堆场使用要求,防尘网基础和轨道梁基础水平位移和沉降均很小,桩土应力比为25.2~43.8,CFG桩网复合地基在350 kPa荷载作用下是稳定安全的,达到了预期加固效果。

基于现场试验的CFG桩复合地基桩帽与垫层效应分析

【目的】柔性垫层和桩帽对CFG桩复合地基的桩土应力比、荷载分担比和沉降均有较大影响,但目前柔性垫层与桩帽在现场试验中如何共同影响复合地基特性仍有待进一步的研究。【方法】以CFG桩复合地基软基处理的某路段作为工程背景,在土工格栅层数不变的情况下,对垫层厚度为100 mm、200 mm、300 mm,桩帽尺寸为0.8 m、1.0 m、1.2 m组合下的形式进行了现场原位试验,研究了CFG桩复合地基的桩土应力比、荷载分担比和沉降特性。【结果】现场试验表明:随着垫层厚度由100 mm增大到300 mm,桩土荷载比减小了51.5%,桩土应力比减小了52.5%,总沉降量增大了7.9%;随着桩帽直径由0.8 m增大到1.2 m,桩土荷载比增大了29.0%,桩土应力比减小了29.2%,总沉降量10.4%.本文区域地质条件,宜选用垫层厚度100 mm、桩帽直径为1.2 m的CFG桩复合地基形式。

CFG桩复合地基设计与施工工艺

以CFG桩复合地基为研究对象,介绍了CFG桩的概念和基本原理,并结合具体工程,从土层参数、桩径、桩间距、面积置换率等方面进行了CFG桩复合地基设计,对CFG桩复合地基施工技术要点展开了研究,开展CFG桩复合地基的现场载荷试验,并对试验结果进行分析。

CFG桩复合地基设计要点

结合已有研究成果及工程实践,从CFG桩复合地基设计角度出发,对设计过程中的附加压力、变形计算深度、压缩模量、压缩模量提高系数、地下水等设计要点进行了分析,并探讨了桩长、桩径、桩间距等参数的选取原则,得出桩径越小,经济性越好,但同时相邻桩相互影响问题更加突出等结论。

提高CFG桩Ⅰ类桩成桩率应用研究

文中结合实际工程实践及相关规范,分析了CFG桩复合地基中影响CFG桩Ⅰ类桩成桩率的因素,通过控制钻机垂直度、混凝土落度、充盈系数等指标,CFG桩I类桩比例由87.3%提升至97.8%,提高了12.1%,效果显著。研究成果可为类似工程提供参考。

水泥土搅拌桩+CFG桩在公路工程软基处理中的应用

文中以绵阳某公路项目为例,对水泥土搅拌桩+CFG桩复合地基在公路工程软基处理中的应用进行研究,采用静载试验对复合地基的承载力特征值进行验证。结果表明,水泥土搅拌桩+CFG桩复合地基展现出良好的承载力和稳定性,具有较高的经济效益和社会效益。

回填土地基上独立基础的CFG桩复合地基设计

CFG桩复合地基主要用于多层及高层建筑物,以往的研究和应用主要是针对基础埋深相对较深的情况。对于回填土地基的独立基础,采用桩基础相对较多,采用CFG桩复合地基较少。文章从受力机理、变形特性和工程造价等角度对桩基础和CFG桩复合地基进行对比分析,探讨了CFG桩复合地基的优势。同时,依托具体工程实例,依据不同规范,对回填土地基上独立基础的CFG桩复合地基沉降计算进行对比分析。结论如下:对于承载力要求不高的独立基础,相比桩基础,CFG桩复合地基在满足承载力和变形控制的前提下,能够大幅度节约工程造价;位于回填土地基上的独立基础CFG桩复合地基设计以沉降控制为主,承载力计算和沉降计算均需考虑填土的不利影响,沉降计算需按照整体进行协同计算。