Electroless Cu plating was used for flake G powder and CNTs, Cu-G-CNTs (copper/graphite/carbon nanotubes) composites were manufactured by means of powder metallurgical method. The influences of CNTs on the mechanica...Electroless Cu plating was used for flake G powder and CNTs, Cu-G-CNTs (copper/graphite/carbon nanotubes) composites were manufactured by means of powder metallurgical method. The influences of CNTs on the mechanical properties, conductivity properties, friction, and wear performance of the composite were examined. The results indicate that adding a small amount of CNTs can improve comprehensive property of the composites, especially mechanical property. However, excessive CNT, which is easily winding reunion and grain boundary seg- regation, results in performances degradation.展开更多
In this article, a novel BiVO4@fibers composite photocatalyst was prepared by a process that monoclinic scheelite BiVO4 nano/micro particles were in situ formated onto fiber materials. The structure, morphology and ph...In this article, a novel BiVO4@fibers composite photocatalyst was prepared by a process that monoclinic scheelite BiVO4 nano/micro particles were in situ formated onto fiber materials. The structure, morphology and photophysical properties of the composite materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and UV-Vis diffuse reflectance spectroscopy, respectively. The immobilization of BiVO4 photocatalyst on fibers reduced the particle size of the photoactive phase, and a few visible-light absorption abilities. The decomposition of a non-biodegradable dye Red FN-3G was selected to examine the photocatalytic activity of the composite photocatalyst. It was found that the formation of composite materials of BiVO4 with fibers didn’t decrease the photocatalytic activity with comparison to that of pure BiVO4. Moreover, it demonstrated that when adjusting the dye solution into about pH = 3, the highest efficiency of dye degradation over the fiber composite material can be obtained.展开更多
As the traditional graphite-based composites cannot meet the requirement of rapid developing modern industry, novel sliding electrical contact materials with high self-lubricating performance in multiple environments ...As the traditional graphite-based composites cannot meet the requirement of rapid developing modern industry, novel sliding electrical contact materials with high self-lubricating performance in multiple environments are eagerly required. Herein a copper-based composite with WS2 and graphite as solid lubricant are fabricated by powder metallurgy hot-pressed method. The friction and wear behaviors of the composites with and without current are investigated under the condition with sliding velocity of 10 m/s and normal load of 2.5N/cm 2 in both air and vacuum. Morphologies of the worn surfaces are observed by optical microscope and compositions of the lubricating films are analyzed by XPS. Surface profile curves and roughness of the worn surfaces are obtained by 2205 surface profiler. The results of wear tests show that the friction coefficient and wear volume loss of the composites with current are greater than that without current in both air and vacuum due to the adverse effects of electrical current which damaged the lubricating film partially and roughed the worn surfaces. XPS results demonstrate that the lubricating film formed in air is composed of oxides of Cu, WS2 , elemental S and graphite, while the lubricating film formed in vacuum is composed of Cu, WS2 and graphite. Because of the synergetic lubricating action of oxides of Cu, WS2 and graphite, the composites show low friction coefficient and wear volume loss in air condition. Owing to the fact that graphite loses its lubricity which makes WS2 become the only lubricant, severe adhesive and abrasive wear occur and result in a high value of wear rate in vacuum condition. The formation of the lubricating film on the contact interface between the brush and ring is one of the factors which can greatly affect the wear performance of the brushes. The low contact voltage drop of the composites in vacuum condition is attributed to the high content of Cu in the surface film. This study fabricated a kind of new sliding electrical contact self-lubricating composite with dual-lubricant which can work well in both air and vacuum environments and provides a comprehensive analysis on the lubrication mechanisms of the composite.展开更多
Novel visible light-induced Cr-doped Sr Ti O3-g-C3N4 composite photocatalysts were synthesized by introducing polymeric g-C3N4. The composite photocatalyst was characterized by X-ray diffraction(XRD), high-resolutio...Novel visible light-induced Cr-doped Sr Ti O3-g-C3N4 composite photocatalysts were synthesized by introducing polymeric g-C3N4. The composite photocatalyst was characterized by X-ray diffraction(XRD), high-resolution transmission electron microscopy(HRTEM), Fourier transform infrared(FT-IR) spectroscopy, UV-vis diffuse reflection spectroscopy, photoluminescence(PL) spectroscopy and BET surface area measurements. The photocatalytic oxidation ability of the novel composite photocatalyst was evaluated using methyl orange(MO) as a target pollutant. The photocatalysts exhibited a significantly enhanced photocatalytic performance in degrading MO. The optimal g-C3N4 content for the photodegradation activity of the composite photocatalysts was determined. The as-prepared composite photocatalyst exhibits an improved photocatalytic activity due to enhancement of photo-generated electron-hole separation at the interface.展开更多
The novel visible light-induced carbon nitride(g-C3N4) and Bi VO4 composite photocatalysts were obtained through a simple mixing-calcination method. The physical and photophysical properties of the Bi VO4-g-C3N4 com...The novel visible light-induced carbon nitride(g-C3N4) and Bi VO4 composite photocatalysts were obtained through a simple mixing-calcination method. The physical and photophysical properties of the Bi VO4-g-C3N4 composites were investigated by X-ray diffraction(XRD), Fourier transform infrared(FTIR) spectroscopy, UV-vis diffuse reflection spectroscopy, high-resolution transmission electron microscopy(HRTEM), photoluminescent(PL) spectroscopy, and BET surface area measurements. Photocatalytic oxidation ability of the prepared samples was examined by studying the degradation of rhodamine B(Rh B) as a target pollutant under visible-light irradiation. The composite photocatalysts exhibited an enhanced photocatalytic performance in degrading Rh B. The optimal g-C3N4 content of the composite photocatalysts was determined for the photodegradation activity. The improved photocatalytic activity of the as-prepared composite photocatalyst may be attributed to the enhancement of photo-generated electron-hole separation at the interface.展开更多
Plain weave woven glass fabric reinforced epoxy (G-E) composite filled with two different types of fillers namely graphite, silicon carbide (each 5 and 10 wt%) was fabricated by hand lay-up method and compressed using...Plain weave woven glass fabric reinforced epoxy (G-E) composite filled with two different types of fillers namely graphite, silicon carbide (each 5 and 10 wt%) was fabricated by hand lay-up method and compressed using hot press. These composites were investigated for their static mechanical properties such as tensile, flexural properties and impact strength as well as mode-I fracture toughness as per ASTM standards. Experimental results on mechanical properties indicate that the strength and the modulus in tensile and flexural mode for G-E composite increase with increasing filler loading. The unfilled G-E composite has the tensile strength of 305 MPa and increased to 404.2 MPa for 10 wt% silicon carbide. However, in three-point bend mode, addition of graphite in G-E showed the highest flexural strength as well as modulus. Mode-I fracture toughness test results indicated that the graphite filler loading improved the toughness of G-E composite. Selected failed samples under tensile, bending and mode-I fracture were examined using scanning electron microscope to identify the fracture features.展开更多
This paper is a brief review of our work on the Planck quantized version of general relativity theory. It demonstrates several straightforward methods to rewrite the same equations that we have already presented in ot...This paper is a brief review of our work on the Planck quantized version of general relativity theory. It demonstrates several straightforward methods to rewrite the same equations that we have already presented in other papers. We also explore a relatively new general relativity-inspired field equation based on the original Newtonian mass, which is very different from today’s kilogram mass. Additionally, we examine two other field equations based on collision space-time, where both energy and matter can be described simply as space and time. We are thereby fulfilling Einstein’s dream of a theory where energy and mass are not needed, or are just aspects of space and time. If this is extended beyond the 4-dimensional space-time formalism of general relativity theory to a 6-dimensional framework with 3 space dimensions and 3 time dimensions, this ultimately reveals that they are two sides of the same coin. In reality, it is a three-dimensional space-time theory, where space and time are just two sides of the same coin.展开更多
基金financially supported by the National Nature Science Foundation of China (No. 51003060)the Distinguished Young Talents in Higher Education of Guangdong China (No. 2012LYM_0118)the Shenzhen Innovation and Technology Commission under the Strategic Emerging Industries Development Project (No. ZDSY20120612094418467)
文摘Electroless Cu plating was used for flake G powder and CNTs, Cu-G-CNTs (copper/graphite/carbon nanotubes) composites were manufactured by means of powder metallurgical method. The influences of CNTs on the mechanical properties, conductivity properties, friction, and wear performance of the composite were examined. The results indicate that adding a small amount of CNTs can improve comprehensive property of the composites, especially mechanical property. However, excessive CNT, which is easily winding reunion and grain boundary seg- regation, results in performances degradation.
文摘In this article, a novel BiVO4@fibers composite photocatalyst was prepared by a process that monoclinic scheelite BiVO4 nano/micro particles were in situ formated onto fiber materials. The structure, morphology and photophysical properties of the composite materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and UV-Vis diffuse reflectance spectroscopy, respectively. The immobilization of BiVO4 photocatalyst on fibers reduced the particle size of the photoactive phase, and a few visible-light absorption abilities. The decomposition of a non-biodegradable dye Red FN-3G was selected to examine the photocatalytic activity of the composite photocatalyst. It was found that the formation of composite materials of BiVO4 with fibers didn’t decrease the photocatalytic activity with comparison to that of pure BiVO4. Moreover, it demonstrated that when adjusting the dye solution into about pH = 3, the highest efficiency of dye degradation over the fiber composite material can be obtained.
基金supported by Major Research Program of National Natural Science Foundation of China(Grant No. 91026018)National Natural Science Foundation of China(Grant No. 60979017)Doctoral Fund of Ministry of Education of China(Grant No. 20110111110015)
文摘As the traditional graphite-based composites cannot meet the requirement of rapid developing modern industry, novel sliding electrical contact materials with high self-lubricating performance in multiple environments are eagerly required. Herein a copper-based composite with WS2 and graphite as solid lubricant are fabricated by powder metallurgy hot-pressed method. The friction and wear behaviors of the composites with and without current are investigated under the condition with sliding velocity of 10 m/s and normal load of 2.5N/cm 2 in both air and vacuum. Morphologies of the worn surfaces are observed by optical microscope and compositions of the lubricating films are analyzed by XPS. Surface profile curves and roughness of the worn surfaces are obtained by 2205 surface profiler. The results of wear tests show that the friction coefficient and wear volume loss of the composites with current are greater than that without current in both air and vacuum due to the adverse effects of electrical current which damaged the lubricating film partially and roughed the worn surfaces. XPS results demonstrate that the lubricating film formed in air is composed of oxides of Cu, WS2 , elemental S and graphite, while the lubricating film formed in vacuum is composed of Cu, WS2 and graphite. Because of the synergetic lubricating action of oxides of Cu, WS2 and graphite, the composites show low friction coefficient and wear volume loss in air condition. Owing to the fact that graphite loses its lubricity which makes WS2 become the only lubricant, severe adhesive and abrasive wear occur and result in a high value of wear rate in vacuum condition. The formation of the lubricating film on the contact interface between the brush and ring is one of the factors which can greatly affect the wear performance of the brushes. The low contact voltage drop of the composites in vacuum condition is attributed to the high content of Cu in the surface film. This study fabricated a kind of new sliding electrical contact self-lubricating composite with dual-lubricant which can work well in both air and vacuum environments and provides a comprehensive analysis on the lubrication mechanisms of the composite.
基金Funded by the National Natural Science Foundation of China(No.51208102)
文摘Novel visible light-induced Cr-doped Sr Ti O3-g-C3N4 composite photocatalysts were synthesized by introducing polymeric g-C3N4. The composite photocatalyst was characterized by X-ray diffraction(XRD), high-resolution transmission electron microscopy(HRTEM), Fourier transform infrared(FT-IR) spectroscopy, UV-vis diffuse reflection spectroscopy, photoluminescence(PL) spectroscopy and BET surface area measurements. The photocatalytic oxidation ability of the novel composite photocatalyst was evaluated using methyl orange(MO) as a target pollutant. The photocatalysts exhibited a significantly enhanced photocatalytic performance in degrading MO. The optimal g-C3N4 content for the photodegradation activity of the composite photocatalysts was determined. The as-prepared composite photocatalyst exhibits an improved photocatalytic activity due to enhancement of photo-generated electron-hole separation at the interface.
基金Funded by the National Natural Science Foundation of China(No.51208102)
文摘The novel visible light-induced carbon nitride(g-C3N4) and Bi VO4 composite photocatalysts were obtained through a simple mixing-calcination method. The physical and photophysical properties of the Bi VO4-g-C3N4 composites were investigated by X-ray diffraction(XRD), Fourier transform infrared(FTIR) spectroscopy, UV-vis diffuse reflection spectroscopy, high-resolution transmission electron microscopy(HRTEM), photoluminescent(PL) spectroscopy, and BET surface area measurements. Photocatalytic oxidation ability of the prepared samples was examined by studying the degradation of rhodamine B(Rh B) as a target pollutant under visible-light irradiation. The composite photocatalysts exhibited an enhanced photocatalytic performance in degrading Rh B. The optimal g-C3N4 content of the composite photocatalysts was determined for the photodegradation activity. The improved photocatalytic activity of the as-prepared composite photocatalyst may be attributed to the enhancement of photo-generated electron-hole separation at the interface.
文摘Plain weave woven glass fabric reinforced epoxy (G-E) composite filled with two different types of fillers namely graphite, silicon carbide (each 5 and 10 wt%) was fabricated by hand lay-up method and compressed using hot press. These composites were investigated for their static mechanical properties such as tensile, flexural properties and impact strength as well as mode-I fracture toughness as per ASTM standards. Experimental results on mechanical properties indicate that the strength and the modulus in tensile and flexural mode for G-E composite increase with increasing filler loading. The unfilled G-E composite has the tensile strength of 305 MPa and increased to 404.2 MPa for 10 wt% silicon carbide. However, in three-point bend mode, addition of graphite in G-E showed the highest flexural strength as well as modulus. Mode-I fracture toughness test results indicated that the graphite filler loading improved the toughness of G-E composite. Selected failed samples under tensile, bending and mode-I fracture were examined using scanning electron microscope to identify the fracture features.
文摘This paper is a brief review of our work on the Planck quantized version of general relativity theory. It demonstrates several straightforward methods to rewrite the same equations that we have already presented in other papers. We also explore a relatively new general relativity-inspired field equation based on the original Newtonian mass, which is very different from today’s kilogram mass. Additionally, we examine two other field equations based on collision space-time, where both energy and matter can be described simply as space and time. We are thereby fulfilling Einstein’s dream of a theory where energy and mass are not needed, or are just aspects of space and time. If this is extended beyond the 4-dimensional space-time formalism of general relativity theory to a 6-dimensional framework with 3 space dimensions and 3 time dimensions, this ultimately reveals that they are two sides of the same coin. In reality, it is a three-dimensional space-time theory, where space and time are just two sides of the same coin.