An atmospheric pressure dielectric barrier discharge （DBD） plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless st...An atmospheric pressure dielectric barrier discharge （DBD） plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless steel or iron plate painted with alkyd or PVC. The experi- mental results of material decontamination show that the residual chemical agent on the material is lower than the permissible value of the National Military Standard of China. In order to test the corrosion effect of the plasma jet on different material surfaces in the decontamination pro-cess, corrosion tests for the materials of polymethyl methacrylate, neoprene, polyvinyl chloride （PVC）, polyethylene （PE）, phenolic resin, iron plate painted with alkyd, stainless steel, aluminum, etc. were carried out, and relevant parameters were examined, including etiolation index, chroma- tism, loss of gloss, corrosion form, etc. The results show that the plasma jet is slightly corrosive for part of the materials, but their performances are not affected. A portable calculator, computer display, mainboard, circuit board of radiogram, and a hygrometer could work normally after being treated by the plasma jet.展开更多
The effects of a co-flow on a spreading and entrainment rate of turbulent round jets have been studied numerically. The first and second order closure models are used and have been comp- ared with existing experimenta...The effects of a co-flow on a spreading and entrainment rate of turbulent round jets have been studied numerically. The first and second order closure models are used and have been comp- ared with existing experimental data. The influence of theses models on the dynamic fields is examined. The results of the models in general agree well with the trends observed experiment- tally. The co-flowing imposed noticeable restri- ctions on the spreading and the turbulent mixing. Finally, an entrainment hypothesis has been introduced to describe the development of turbulent jets issuing into a stagnant or co-flowing air. It relates the mass flow rate of the surround- ing fluid entrained into the jet to the characteristic velocity difference between the jet and the co-flow. It is obvious that the co-flow decreases considerably the entrainment of air.展开更多
The jet co-flow packing tray(JCPT) with three different types of perforation in equal opening fraction was tested in two rectangular columns with 0.12 m in width and 0.27 m in length operated with air-water system.The...The jet co-flow packing tray(JCPT) with three different types of perforation in equal opening fraction was tested in two rectangular columns with 0.12 m in width and 0.27 m in length operated with air-water system.The influences of gas phase orifice F-factor and clear liquid height He on the amount of liquid lifted, Q, were examined. The corresponding correlation between Q with F-factor and equivalent diameter of perforated holes as well as Hc was obtained. Furthermore, the non-steady state mass transfer performance of JCPT was tested by the humidification of air with water. Finally, by the analysis of data and comparison, it was found that the JCPT tray with single cap and two holes exhibited the highest mass transfer efficiency and best performance.展开更多
The study of swirling jet combustor for biomass coal co-firing is of great interest for energy industry. The biomass co-firing can serve as a NOx reduction method as well as the better use of renewable energy source. ...The study of swirling jet combustor for biomass coal co-firing is of great interest for energy industry. The biomass co-firing can serve as a NOx reduction method as well as the better use of renewable energy source. Large eddy simulation (LES) and RANS modelling have been performed with two different burner designs. Usually pulverized coal-biomass mixture enters the furnace along with primary air through primary pipe, and the secondary pipe provides necessary air and mixing for combustion. The improved model has three passages including primary, secondary and middle passage for swirling. The simulations on two geometries have been compared, and the aim is to design a better and improved burner model for better pre-combustion mixing in the biomass co- fired furnace. The results from two-way and three-way geometry have been compared with each other as well as with the results from the furnace model used by Apte and Mahesh [8].展开更多
文摘An atmospheric pressure dielectric barrier discharge （DBD） plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless steel or iron plate painted with alkyd or PVC. The experi- mental results of material decontamination show that the residual chemical agent on the material is lower than the permissible value of the National Military Standard of China. In order to test the corrosion effect of the plasma jet on different material surfaces in the decontamination pro-cess, corrosion tests for the materials of polymethyl methacrylate, neoprene, polyvinyl chloride （PVC）, polyethylene （PE）, phenolic resin, iron plate painted with alkyd, stainless steel, aluminum, etc. were carried out, and relevant parameters were examined, including etiolation index, chroma- tism, loss of gloss, corrosion form, etc. The results show that the plasma jet is slightly corrosive for part of the materials, but their performances are not affected. A portable calculator, computer display, mainboard, circuit board of radiogram, and a hygrometer could work normally after being treated by the plasma jet.
文摘The effects of a co-flow on a spreading and entrainment rate of turbulent round jets have been studied numerically. The first and second order closure models are used and have been comp- ared with existing experimental data. The influence of theses models on the dynamic fields is examined. The results of the models in general agree well with the trends observed experiment- tally. The co-flowing imposed noticeable restri- ctions on the spreading and the turbulent mixing. Finally, an entrainment hypothesis has been introduced to describe the development of turbulent jets issuing into a stagnant or co-flowing air. It relates the mass flow rate of the surround- ing fluid entrained into the jet to the characteristic velocity difference between the jet and the co-flow. It is obvious that the co-flow decreases considerably the entrainment of air.
文摘The jet co-flow packing tray(JCPT) with three different types of perforation in equal opening fraction was tested in two rectangular columns with 0.12 m in width and 0.27 m in length operated with air-water system.The influences of gas phase orifice F-factor and clear liquid height He on the amount of liquid lifted, Q, were examined. The corresponding correlation between Q with F-factor and equivalent diameter of perforated holes as well as Hc was obtained. Furthermore, the non-steady state mass transfer performance of JCPT was tested by the humidification of air with water. Finally, by the analysis of data and comparison, it was found that the JCPT tray with single cap and two holes exhibited the highest mass transfer efficiency and best performance.
文摘The study of swirling jet combustor for biomass coal co-firing is of great interest for energy industry. The biomass co-firing can serve as a NOx reduction method as well as the better use of renewable energy source. Large eddy simulation (LES) and RANS modelling have been performed with two different burner designs. Usually pulverized coal-biomass mixture enters the furnace along with primary air through primary pipe, and the secondary pipe provides necessary air and mixing for combustion. The improved model has three passages including primary, secondary and middle passage for swirling. The simulations on two geometries have been compared, and the aim is to design a better and improved burner model for better pre-combustion mixing in the biomass co- fired furnace. The results from two-way and three-way geometry have been compared with each other as well as with the results from the furnace model used by Apte and Mahesh [8].
