Displacement characteristics of CO_(2)flooding in extra-high water-cut reservoirs

Carbon dioxide(CO_(2))flooding is a widely applied recovery method during the tertiary recovery of oil and gas.A high water saturation condition in reservoirs could induce a‘water shielding’phenomenon after the injection of CO_(2).This would prevent contact between the injected gas and the residual oil,restricting the development of the miscible zone.A micro-visual experiment of dead-end models,used to observe the effect of a film of water on the miscibility process,indicates that CO_(2)can penetrate the water film and come into contact with the residual oil,although the mixing is significantly delayed.However,the dissolution loss of CO_(2)at high water-cut conditions is not negligible.The oil-water partition coefficient,defined as the ratio of CO_(2)solubility in an oil-brine/two-phase system,keeps constant for specific reservoir conditions and changes little with an injection gas.The NMR device shows that when CO_(2)flooding follows water flooding,the residual oil decreasesdnot only in medium and large pores but also in small and micro pores.At levels of higher water saturation,CO_(2)displacement is characterized initially by a low oil production rate and high water-cut.After the CO_(2)breakthrough,the water-cut decreases sharply and the oil production rate increases gradually.The response time of CO_(2)flooding at high watercut reservoirs is typically delayed and prolonged.These results were confirmed in a pilot test for CO_(2)flooding at the P1-1 well group of the Pucheng Oilfield.Observations from this pilot study also suggest that a larger injection gas pore volume available for CO_(2)injection is required to offset the dissolution loss in high water saturation conditions.

Effect of CO_(2)flooding in an oil reservoir with strong bottom-water drive in the Tahe Oilfield,Tarim Basin,Northwest China

The dissolution and diffusion of CO_(2)in oil and water and its displacement mechanism were investigated by laboratory experiment and numerical simulation for Block 9 in the Tahe oilfield,a sandstone oil reservoir with strong bottom-water drive in Tarim Basin,Northwest China.Such parameters were analyzed as solubility ratio of CO_(2)in oil,gas and water,interfacial tension,in-situ oil viscosity distribution,remaining oil saturation distribution,and oil compositions.The results show that CO_(2)flooding could control water coning and increase oil production.In the early stage of the injection process,CO_(2)expanded vertically due to gravity differentiation,and extended laterally under the action of strong bottom water in the intermediate and late stages.The CO_(2)got enriched and extended at the oil-water interface,forming a high interfacial tension zone,which inhibited the coning of bottom water to some extent.A miscible region with low interfacial tension formed at the gas injection front,which reduced the in-situ oil viscosity by about 50%.The numerical simulation results show that enhanced oil recovery(EOR)is estimated at 5.72%and the oil exchange ratio of CO_(2)is 0.17 t/t.

Influence of reservoir heterogeneity on immiscible water-alternating-CO_(2)flooding:A case study

Currently,limited studies of immiscible water-alternating-CO_(2)(imWACO_(2))flooding focus on the impact of reservoir heterogeneity on reservoir development outcomes.Given this,using the heterogeneous reservoirs in the Gao 89-1 block as a case study,this study conducted slab core flooding experiments and numerical simulations to assess the impact of reservoir heterogeneity on imWACO_(2)flooding efficiency.It can be concluded that imWACO_(2)flooding can enhance the sweep volume and oil recovery compared to continuous CO_(2)flooding.As the permeability difference increases,the difference in the swept volume between zones/layers with relatively high and low permeability increases.To optimize the exploitation of reservoirs in the Gao 89-1 block,the optimal timing and CO_(2)injection rate for imWACO_(2)flooding are determined at water cut of 40%and 10000 m^(3)/d,respectively.A short injection-production semi-period,combined with multiple cycles of water and CO_(2)injection alternations,is beneficial for enhanced oil recovery from imWACO_(2)flooding.

Seismic dynamic monitoring in CO_2 flooding based on characterization of frequency-dependent velocity factor

The phase velocity of seismic waves varies with the propagation frequency, and thus frequency-dependent phenomena appear when CO2 gas is injected into a reservoir. By dynamically considering these phenomena with reservoir conditions it is thus feasible to extract the frequency-dependent velocity factor with the aim of monitoring changes in the reservoir both before and after CO2 injection. In the paper, we derive a quantitative expression for the frequency-dependent factor based on the Robinson seismic convolution model. In addition, an inversion equation with a frequency-dependent velocity factor is constructed, and a procedure is implemented using the following four processing steps： decomposition of the spectrum by generalized S transform, wavelet extraction of cross-well seismic traces, spectrum equalization processing, and an extraction method for frequency-dependent velocity factor based on the damped least-square algorithm. An attenuation layered model is then established based on changes in the Q value of the viscoelastic medium, and spectra of migration profiles from forward modeling are obtained and analyzed. Frequency-dependent factors are extracted and compared, and the effectiveness of the method is then verified using a synthetic data. The frequency-dependent velocity factor is finally applied to target processing and oil displacement monitoring based on real seismic data obtained before and after CO2 injection in the G89 well block within Shengli oilfield. Profiles and slices of the frequency-dependent factor determine its ability to indicate differences in CO2 flooding, and the predicting results are highly consistent with those of practical investigations within the well block.

Influence of pore structure heterogeneity on channeling channels during hot water flooding in heavy oil reservoir based on CT scanning

Hot water flooding is an effective way to develop heavy oil reservoirs.However,local channeling channels may form,possibly leading to a low thermal utilization efficiency and high water cut in the reservoir.The pore structure heterogeneity is an important factor in forming these channels.This study proposes a method that mixes quartz sand with different particle sizes to prepare weakly heterogeneous and strongly heterogeneous models through which hot water flooding experiments are conducted.During the experiments,computer tomography(CT)scanning identifies the pore structure and micro remaining oil saturation distribution to analyze the influence of the pore structure heterogeneity on the channeling channels.The oil saturation reduction and average pore size are divided into three levels to quantitatively describe the relationship between the channeling channel distribution and pore structure heterogeneity.The zone where oil saturation reduction exceeds 20%is defined as a channeling channel.The scanning area is divided into 180 equally sized zones based on the CT scanning images,and threedimensional(3D)distributions of the channeling channels are developed.Four micro remaining oil distribution patterns are proposed,and the morphology characteristics of micro remaining oil inside and outside the channeling channels are analyzed.The results show that hot water flooding is more balanced in the weakly heterogeneous model,and the oil saturation decreases by more than 20%in most zones without narrow channeling channels forming.In the strongly heterogeneous model,hot water flooding is unbalanced,and three narrow channeling channels of different lengths form.In the weakly heterogeneous model,the oil saturation reduction is greater in zones with larger pores.The distribution range of the average pore size is larger in the strongly heterogeneous model.The network remaining oil inside the channeling channels is less than outside the channeling channels,and the hot water converts the network remaining oil into cluster,film,and droplet remaining oil.

CO_(2)high-pressure miscible flooding and storage technology and its application in Shengli Oilfield,China

There are various issues for CO_(2)flooding and storage in Shengli Oilfield,which are characterized by low light hydrocarbon content of oil and high miscible pressure,strong reservoir heterogeneity and low sweep efficiency,gas channeling and difficult whole-process control.Through laboratory experiments,technical research and field practice,the theory and technology of CO_(2)high pressure miscible flooding and storage are established.By increasing the formation pressure to 1.2 times the minimum miscible pressure,the miscibility of the medium-heavy components can be improved,the production percentage of oil in small pores can be increased,the displacing front developed evenly,and the swept volume expanded.Rapid high-pressure miscibility is realized through advanced pressure flooding and energy replenishment,and technologies of cascade water-alternating-gas(WAG),injection and production coupling and multistage chemical plugging are used for dynamic control of flow resistance,so as to obtain the optimum of oil recovery and CO_(2)storage factor.The research results have been applied to the Gao89-Fan142 in carbon capture,utilization and storage(CCUS)demonstration site,where the daily oil production of the block has increased from 254.6 t to 358.2 t,and the recovery degree is expected to increase by 11.6 percentage points in 15 years,providing theoretical and technical support for the large-scale development of CCUS.

Profile improvement during CO_2 flooding in ultra-low permeability reservoirs

Gas flooding such as CO2 flooding may be effectively applied to ultra-low permeability reservoirs, but gas channeling is inevitable due to low viscosity and high mobility of gas and formation heterogeneity. In order to mitigate or prevent gas channeling, ethylenediamine is chosen for permeability profile control. The reaction mechanism of ethylenediamine with CO2, injection performance, swept volume, and enhanced oil recovery were systematically evaluated. The reaction product of ethylenediamine and CO2 was a white solid or a light yellow viscous liquid, which would mitigate or prevent gas channeling. Also, ethylenediamine could be easily injected into ultra-low permeability cores at high temperature with protective ethanol slugs. The core was swept by injection of 0.3 PV ethylenediamine. Oil displacement tests performed on heterogeneous models with closed fractures, oil recovery was significantly enhanced with injection of ethylenediamine. Experimental results showed that using ethylenediamine to plug high permeability layers would provide a new research idea for the gas injection in fractured, heterogeneous and ultra-low permeability reservoirs. This technology has the potential to be widely applied in oilfields.

Advanced treatment of oil recovery wastewater from polymer flooding by UV/H_2O_2/O_3 and fine filtration

In order to purify oil recovery wastewater from polymer flooding （ORWPF） in tertiary oil recovery in oil fields, advanced treatment of UV/H2O2/O3 and fine filtration were investigated. The experimental results showed that polyacrylamide and oil remaining in ORWPF after the conventional treatment process could be effectively removed by UV/H2O2/O3 process. Fine filtration gave a high performance in eliminating suspended solids. The treated ORWPF can meet the quality requirement of the wastewater-bearing polymer injection in oilfield and be safely re-injected into oil reservoirs for oil recovery.

Modeling CO_2 miscible flooding for enhanced oil recovery

The injection of fuel-generated CO2 into oil reservoirs will lead to two benefits in both enhanced oil recovery （EOR） and the reduction in atmospheric emission of CO2. To get an insight into CO2 miscible flooding performance in oil reservoirs, a multi-compositional non-isothermal CO2 miscible flooding mathematical model is developed. The convection and diffusion of CO2-hydrocarbon mixtures in multiphase fluids in reservoirs, mass transfer between CO2 and crude, and formation damages caused by asphaltene precipitation are fully considered in the model. The governing equations are discretized in space using the integral finite difference method. The Newton-Raphson iterative technique was used to solve the nonlinear equation systems of mass and energy conservation. A numerical simulator, in which regular grids and irregular grids are optional, was developed for predicting CO2 miscible flooding processes. Two examples of one-dimensional （1D） regular and three-dimensional （3D） rectangle and polygonal grids are designed to demonstrate the functions of the simulator. Experimental data validate the developed simulator by comparison with 1D simulation results. The applications of the simulator indicate that it is feasible for predicting CO2 flooding in oil reservoirs for EOR.

Effect of stress sensitivity on displacement efficiency in CO_2 flooding for fractured low permeability reservoirs

Carbon dioxide flooding is an effective means of enhanced oil recovery for low permeability reservoirs. If fractures are present in the reservoir, CO2 may flow along the fractures, resulting in low gas displacement efficiency. Reservoir pore pressure will fluctuate to some extent during a CO2 flood, causing a change in effective confining pressure. The result is rock deformation and a reduction in permeability with the reduction in fracture permeability, causing increased flow resistance in the fracture space. Simultaneously, gas cross flowing along the fractures is partially restrained. In this work, the effect of stress changes on permeability was studied through a series of flow experiments. The change in the flowrate distribution in a matrix block and contained fracture with an increase in effective pressure were analyzed. The results lead to an implicit comparison which shows that permeability of fractured core decreases sharply with an increase in effective confining pressure. The fracture flowrate ratio declines and the matrix flowrate ratio increases. Fracture flow will partially divert to the matrix block with the increase in effective confining pressure, improving gas displacement efficiency.

CO_2-triggered gelation for mobility control and channeling blocking during CO_2 flooding processes

CO2 flooding is regarded as an important method for enhanced oil recovery （EOR） and greenhouse gas control. However, the heterogeneity prevalently dis- tributed in reservoirs inhibits the performance of this technology. The sweep efficiency can be significantly reduced especially in the presence of ＂thief zones＂. Hence, gas channeling blocking and mobility control are important technical issues for the success of CO2 injection. Normally, crosslinked gels have the potential to block gas channels, but the gelation time control poses challenges to this method. In this study, a new method for selectively blocking CO2 channeling is proposed, which is based on a type of CO2-sensitive gel system （modified polyacry- lamide-methenamine-resorcinol gel system） to form gel in situ. A CO2-sensitive gel system is when gelation or solidification will be triggered by CO2 in the reservoir to block gas channels. The CO2-sensitivity of the gel system was demonstrated in parallel bottle tests of gel in N2 and CO2 atmospheres. Sand pack flow experiments were con- ducted to investigate the shutoff capacity of the gel system under different conditions. The injectivity of the gel system was studied via viscosity measurements. The results indi- cate that this gel system was sensitive to CO2 and had good performance of channeling blocking in porous media. Advantageous viscosity-temperature characteristics were achieved in this work. The effectiveness for EOR in heterogeneous formations based on this gel system was demonstrated using displacement tests conducted in double sand packs. The experimental results can provide guideli- nes for the deployment of theCO2-sensitive gel system for field applications.

Integrated Techniques of Underground CO_2 Storage and Flooding Put into Commercial Application in the Jilin Oilfield, China

Global warming touches everybody＇s nerve, and direct reason for sharp increasing of CO2 in the atmosphere results mainly from the use of fossil fuel in power generation and other industries. How can humans return this ＂devil＂ to underground, and keep a peaceful environment for human？ Scientists from all over the world have been exploring them.

Experimental study on asphaltene precipitation induced by CO_2 flooding

The effects of CO2 pressure,temperature and concentration on asphaltene precipitation induced by CO2 were studied using a high-pressure vessel,interfacial tensiometer,Fourier transform infrared （FTIR） and drill core displacement experimental apparatus.The results indicated that the content of asphaltene in crude oil decreased,and the interfacial tension between a model oil and distilled water increased,with an increase of CO2 pressure,decrease of temperature and increase of molar ratio of CO2 to crude oil when CO2 contacted crude oil in the high pressure vessel.The content of asphaltene in sweepout oil and the permeability of test cores both also decreased with an increase of CO2 flooding pressure.The main reason for changes in content of asphaltene in crude oil,in interfacial tension between model oil and distilled water and in the permeability of the test core is the precipitation of asphaltene which is an interfacially active substance in crude oil.Precipitation of asphaltene also blocks pores in the drill core which decreases the permeability.

Response of Growth and Water Use Efficiency of Spring Wheat to Whole Season CO_2 Enrichment and Drought

Whole_growing season pot experiments were conducted to examine the response of growth and water use efficiency ( WUE ) of spring wheat ( Triticum aestivum L. cv. Gaoyuan 602) to CO 2 enrichment. Wheat plants were grown in open_top chambers (OTCs) subject to two concentrations of CO 2 ()(350 and 700 μL/L, hereafter 'ambient' and 'elevated' respectively) and three soil water levels (80%, 60% and 40% field water capacity ( FWC ), hereafter 'high soil moisture', 'medium soil moisture' and 'low soil moisture' respectively). Elevated CO 2 greatly increased leaf net photosynthesis ( Pn ) at all three soil water levels. The Pn of plants growing under elevated was 22% lower than that of plants growing at ambient when measured with the same (700 μL/L). Plant growth was enhanced by elevated throughout the growing season, with an increase of 14.8% in shoot dry weight at harvest under high soil moisture, and leaf area was increased by about 20% at all three soil water levels. Elevated in combination with high soil moisture increased the ratio of plant shoot dry weight to height by 15.7%, while this ratio was decreased by over 50% when plants were subject to drought. Elevated also increased the water use efficiency of wheat, mainly due to decreases in transpiration and cumulative consumption of water, and an increase in shoot dry weight, with the biggest value of 30% occurring at high soil water moisture level. Compared to high soil moisture, drought decreased shoot dry weight by 72% under ambient , and by 76% under elevated . Similarly, drought also reduced WUE by 19% under ambient , and 23% under elevated . Our results indicate that: (1) elevated can increase the photosynthetic rates, growth and WUE of wheat plants; (2) long_term exposure to high may result in lower photosynthetic capacity; (3) high stimulates plants lateral growth more than vertical growth; (4) the effects of CO 2 enrichment on plants depend on soil water status, with plants benefiting more from CO 2 enrichment if sufficient water is supplied; and (5) drought may cause relatively more reduction in plant growth and WUE under future elevated conditions.

Influence of CO_2 Doubling on Water Transport Process at Root/Soil Interface of Pinus sylvestris var. sylvestriformis Seedlings

Water transport at the root/soil interface of 1 year old Pinus sylvestris Linn. var. sylvestriformis (Takenouchi) Cheng et C. D. Chu seedlings under CO 2 doubling was studied by measuring soil electric conductance to survey soil water profiles and comparing it with root distribution surveyed by soil coring and root harvesting in Changbai Mountain in 1999. The results were: (1) The profiles of soil water content were adjusted by root activity. The water content of the soil layer with abundant roots was higher. (2) When CO 2 concentration was doubled, water transport was more active at the root/soil interface and the roots were distributed into deeper layer. It was shown in this work that the method of measuring electric conductance is an inexpensive, non_destructive and relatively sensitive way for underground water transport process.

氮硫共掺杂生物炭的制备及其对Ni^(2+)和Co^(2+)的吸附

以芦荟皮为原料、(NH_(4))_(2)SO_(4)为氮源和硫源,采用水热法制备了炭前驱体,再经高温热解制备了氮硫共掺杂生物炭(NSBC)。采用SEM、BET、XPS、Zeta电位对其进行了表征,考察了不同温度热解制备的NSBC对水溶液中Ni^(2+)、Co^(2+)的吸附性能,探究了NSBC吸附Ni^(2+)、Co^(2+)的热力学和动力学过程,分析了温度和pH对其吸附性能的影响,并推测其吸附机理。结果表明,NSBC表面为层片状堆积的多孔结构,热解温度800℃制备的NSBC_(800)具有分级多孔结构,微孔总体积0.07 cm^(3)/g,比表面积149 m^(2)/g,非微孔体积占比46%,其表面具有摩尔分数29.94%的O元素、4.79%的N元素和6.21%的S元素。NSBC_(800)对Ni^(2+)和Co^(2+)的最大平衡吸附量分别为245.70和223.71 mg/g。NSBC表面由O、N和S元素组成的化学官能团吸附Ni^(2+)和Co^(2+)反应生成盐或络合物,沉积在生物炭表面;Langmuir模型和拟二级动力学模型描述的NSBC对Ni^(2+)和Co^(2+)的吸附表明,该过程由化学吸附控制,通过络合作用、共沉淀、离子交换和静电吸引等机制实现对Ni^(2+)和Co^(2+)的吸附。

注CO_(2)驱提高致密砂岩气藏采收率实验及数值模拟

针对致密砂岩气藏地层压力下降快、稳产难度大、采收率较低等问题,利用长岩心驱替实验、可视化实验和数值模拟方法,从提高气藏采收率方面对注CO_(2)的驱替特征和扩散特征进行了研究。结果表明:地层中的超临界CO_(2)不是与天然气大范围地互溶,而是“部分互溶”;由于重力分异作用,CO_(2)在沉降过程中驱替天然气向上运移并被采出;CO_(2)驱替天然气可提高采收率17.8百分点。研究成果可为下一步致密砂岩气藏CO_(2)驱矿场试验提供理论依据。

Recent advances and future prospects on Ni_(3)S_(2)-Based electrocatalysts for efficient alkaline water electrolysis

Green hydrogen(H_(2))produced by renewable energy powered alkaline water electrolysis is a promising alternative to fossil fuels due to its high energy density with zero-carbon emissions.However,efficient and economic H_(2) production by alkaline water electrolysis is hindered by the sluggish hydrogen evolution reaction(HER)and oxygen evolution reaction(OER).Therefore,it is imperative to design and fabricate high-active and low-cost non-precious metal catalysts to improve the HER and OER performance,which affects the energy efficiency of alkaline water electrolysis.Ni_(3)S_(2) with the heazlewoodite structure is a potential electrocatalyst with near-metal conductivity due to the Ni–Ni metal network.Here,the review comprehensively presents the recent progress of Ni_(3)S_(2)-based electrocatalysts for alkaline water electrocatalysis.Herein,the HER and OER mechanisms,performance evaluation criteria,preparation methods,and strategies for performance improvement of Ni_(3)S_(2)-based electrocatalysts are discussed.The challenges and perspectives are also analyzed.

Transcriptomics integrated with metabolomics reveals the mechanism of CaCl_(2)-HCl electrolyzed water-induced glucosinolate biosynthesis in broccoli sprouts

Glucosinolates are important phytochemicals in Brassicaceae.We investigated the effect of CaCl_(2)-HCl electrolyzed water(CHEW)on glucosinolates biosynthesis in broccoli sprouts.The results showed that CHEW treatment significantly decreased reactive oxygen species(ROS)and malondialdeh yde(MDA)contents in broccoli sprouts.On the the 8^(th)day,compared to tap water treatment,the the total glucosinolate content of broccoli sprouts with CHEW treatment increased by 10.6%and calcium content was dramatically enhanced from 14.4 mg/g DW to 22.7 mg/g DW.Comparative transcriptome and metabolome analyses revealed that CHEW treatment activated ROS and calcium signaling transduction pathways in broccoli sprouts and they interacted through MAPK cascades.Besides,CHEW treatment not only promoted the biosynthesis of amino acids,but also enhanced the expression of structural genes in glucosinolate synthesis through transcription factors(MYBs,bHLHs,WRKYs,etc.).The results of this study provided new insights into the regulatory network of glucosinolates biosynthesis in broccoli sprouts under CHEW treatment.

Effects of physical parameter range on dimensionless variable sensitivity in water flooding reservoirs

The similarity criterion for water flooding reservoir flows is concerned with in the present paper. When finding out all the dimensionless variables governing this kind of flow, their physical meanings are subsequently elucidated. Then, a numerical approach of sensitivity analysis is adopted to quantify their corresponding dominance degree among the similarity parameters. In this way, we may finally identify major scaling law in different parameter range and demonstrate the respective effects of viscosity, permeability and injection rate.