Accurate initial soil conditions play a crucial role in simulating soil hydrothermal and surface energy fluxes in land surface process modeling.This study emphasized the influence of the initial soil temperature(ST)an...Accurate initial soil conditions play a crucial role in simulating soil hydrothermal and surface energy fluxes in land surface process modeling.This study emphasized the influence of the initial soil temperature(ST)and soil moisture(SM)conditions on a land surface energy and water simulation in the permafrost region in the Tibetan Plateau(TP)using the Community Land Model version 5.0(CLM5.0).The results indicate that the default initial schemes for ST and SM in CLM5.0 were simplistic,and inaccurately represented the soil characteristics of permafrost in the TP which led to underestimating ST during the freezing period while overestimating ST and underestimating SLW during the thawing period at the XDT site.Applying the long-term spin-up method to obtain initial soil conditions has only led to limited improvement in simulating soil hydrothermal and surface energy fluxes.The modified initial soil schemes proposed in this study comprehensively incorporate the characteristics of permafrost,which coexists with soil liquid water(SLW),and soil ice(SI)when the ST is below freezing temperature,effectively enhancing the accuracy of the simulated soil hydrothermal and surface energy fluxes.Consequently,the modified initial soil schemes greatly improved upon the results achieved through the long-term spin-up method.Three modified initial soil schemes experiments resulted in a 64%,88%,and 77%reduction in the average mean bias error(MBE)of ST,and a 13%,21%,and 19%reduction in the average root-mean-square error(RMSE)of SLW compared to the default simulation results.Also,the average MBE of net radiation was reduced by 7%,22%,and 21%.展开更多
China is home to shales of three facies:Marine shale,continental shale,and marine-continental transitional shale.Different types of shale gas are associated with significantly different formation conditions and major ...China is home to shales of three facies:Marine shale,continental shale,and marine-continental transitional shale.Different types of shale gas are associated with significantly different formation conditions and major controlling factors.This study compared the geological characteristics of various shales and analyzed the influences of different parameters on the formation and accumulation of shale gas.In general,shales in China’s several regions exhibit high total organic carbon(TOC)contents,which lays a sound material basis for shale gas generation.Marine strata generally show high degrees of thermal evolution.In contrast,continental shales manifest low degrees of thermal evolution,necessitating focusing on areas with relatively high degrees of thermal evolution in the process of shale gas surveys for these shales.The shales of the Wufeng and Silurian formations constitute the most favorable shale gas reservoirs since they exhibit the highest porosity among the three types of shales.These shales are followed by those in the Niutitang and Longtan formations.In contrast,the shales of the Doushantuo,Yanchang,and Qingshankou formations manifest low porosities.Furthermore,the shales of the Wufeng and Longmaxi formations exhibit high brittle mineral contents.Despite a low siliceous mineral content,the shales of the Doushantuo Formation feature a high carbonate mineral content,which can increase the shales’brittleness to some extent.For marine-continental transitional shales,where thin interbeds of tight sandstone with unequal thicknesses are generally found,it is recommended that fracturing combined with drainage of multiple sets of lithologic strata should be employed to enhance their shale gas production.展开更多
The determination of the ultimate load-bearing capacity of structures made of elastoplastic heterogeneous materials under varying loads is of great importance for engineering analysis and design. Therefore, it is nece...The determination of the ultimate load-bearing capacity of structures made of elastoplastic heterogeneous materials under varying loads is of great importance for engineering analysis and design. Therefore, it is necessary to accurately predict the shakedown domains of these materials. The static shakedown theorem, also known as Melan's theorem, is a fundamental method used to predict the shakedown domains of structures and materials. Within this method, a key aspect lies in the construction and application of an appropriate self-equilibrium stress field(SSF). In the structural shakedown analysis, the SSF is typically constructed by governing equations that satisfy no external force(NEF) boundary conditions. However, we discover that directly applying these governing equations is not suitable for the shakedown analysis of heterogeneous materials. Researchers must consider the requirements imposed by the Hill-Mandel condition for boundary conditions and the physical significance of representative volume elements(RVEs). This paper addresses this issue and demonstrates that the sizes of SSFs vary under different boundary conditions, such as uniform displacement boundary conditions(DBCs), uniform traction boundary conditions(TBCs), and periodic boundary conditions(PBCs). As a result, significant discrepancies arise in the predicted shakedown domain sizes of heterogeneous materials. Built on the demonstrated relationship between SSFs under different boundary conditions, this study explores the conservative relationships among different shakedown domains, and provides proof of the relationship between the elastic limit(EL) factors and the shakedown loading factors under the loading domain of two load vertices. By utilizing numerical examples, we highlight the conservatism present in certain results reported in the existing literature. Among the investigated boundary conditions, the obtained shakedown domain is the most conservative under TBCs.Conversely, utilizing PBCs to construct an SSF for the shakedown analysis leads to less conservative lower bounds, indicating that PBCs should be employed as the preferred boundary conditions for the shakedown analysis of heterogeneous materials.展开更多
This study aims to quantify the susceptibility of granular materials used in pavements to changes in moisture content and propose a correlation model to incorporate this susceptibility into seasonal analyses.The fines...This study aims to quantify the susceptibility of granular materials used in pavements to changes in moisture content and propose a correlation model to incorporate this susceptibility into seasonal analyses.The fines content and the percentage of fractured coarse aggregates were identified as direct indicators of the resilient modulus susceptibility to changes in water content.The results showed that the percentage of fractured coarse aggregates particles(FR)has a more significant impact on the resilient modulus(Er)of crushed granular materials used in pavement construction than the combined indicator of the fines content and sample volumetrics(nf).Crushed granular materials with a higher percentage of fractured coarse aggregates are relatively insensitive to changes in the degree of saturation,but become more sensitive as the fine fraction porosity decreases.An adjusted model was proposed based on the existing formulation,but considers a complex parameter to describe and adjust the sensitivity of base granular materials to variations in moisture content with respect to fabrication charac-teristics,fines content and volumetric properties.The model shows that the variation of Er values is below10%for fully crushed granular materials.However,it reaches approximately±12%for materials with 75%of crushed coarse aggregates andþ40%and-25%for materials with FR=50%.This model could help select good ag-gregates characteristics and adjust grain-size distribution for environments where significant moisture content variations can occur in the pavement system,such as in the Province of Quebec(Canada).As it is based on pa-rameters that can be easily determined or estimated,it also represents a valuable tool for detailed design and analysis that can consider material characteristics.展开更多
A photovoltaic (PV) string with multiple modules with bypass diodes frequently deployed on a variety of autonomous PV systems may present multiple power peaks under uneven shading. For optimal solar harvesting, there ...A photovoltaic (PV) string with multiple modules with bypass diodes frequently deployed on a variety of autonomous PV systems may present multiple power peaks under uneven shading. For optimal solar harvesting, there is a need for a control schema to force the PV string to operate at global maximum power point (GMPP). While a lot of tracking methods have been proposed in the literature, they are usually complex and do not fully take advantage of the available characteristics of the PV array. This work highlights how the voltage at operating point and the forward voltage of the bypass diode are considered to design a global maximum power point tracking (GMPPT) algorithm with a very limited global search phase called Fast GMPPT. This algorithm successfully tracks GMPP between 94% and 98% of the time under a theoretical evaluation. It is then compared against Perturb and Observe, Deterministic Particle Swarm Optimization, and Grey Wolf Optimization under a sequence of irradiance steps as well as a power-over-voltage characteristics profile that mimics the electrical characteristics of a PV string under varying partial shading conditions. Overall, the simulation with the sequence of irradiance steps shows that while Fast GMPPT does not have the best convergence time, it has an excellent convergence rate as well as causes the least amount of power loss during the global search phase. Experimental test under varying partial shading conditions shows that while the GMPPT proposal is simple and lightweight, it is very performant under a wide range of dynamically varying partial shading conditions and boasts the best energy efficiency (94.74%) out of the 4 tested algorithms.展开更多
In this paper, the inverse spectral problem of Sturm-Liouville operator with boundary conditions and jump conditions dependent on the spectral parameter is investigated. Firstly, the self-adjointness of the problem an...In this paper, the inverse spectral problem of Sturm-Liouville operator with boundary conditions and jump conditions dependent on the spectral parameter is investigated. Firstly, the self-adjointness of the problem and the eigenvalue properties are given, then the asymptotic formulas of eigenvalues and eigenfunctions are presented. Finally, the uniqueness theorems of the corresponding inverse problems are given by Weyl function theory and inverse spectral data approach.展开更多
Background:Persons with mental disorders are at a higher risk than the general population for the subsequent development of certain medical conditions.Methods:We used a population-based cohort from Danish national reg...Background:Persons with mental disorders are at a higher risk than the general population for the subsequent development of certain medical conditions.Methods:We used a population-based cohort from Danish national registries that included data on more than 5.9 million persons born in Denmark from 1900 through 2015 and followed them from 2000 through 2016,for a total of 83.9 million person-years.展开更多
Laminated composites are widely used in many engineering industries such as aircraft, spacecraft, boat hulls, racing car bodies, and storage tanks. We analyze the 3D deformations of a multilayered, linear elastic, ani...Laminated composites are widely used in many engineering industries such as aircraft, spacecraft, boat hulls, racing car bodies, and storage tanks. We analyze the 3D deformations of a multilayered, linear elastic, anisotropic rectangular plate subjected to arbitrary boundary conditions on one edge and simply supported on other edge. The rectangular laminate consists of anisotropic and homogeneous laminae of arbitrary thicknesses. This study presents the elastic analysis of laminated composite plates subjected to sinusoidal mechanical loading under arbitrary boundary conditions. Least square finite element solutions for displacements and stresses are investigated using a mathematical model, called a state-space model, which allows us to simultaneously solve for these field variables in the composite structure’s domain and ensure that continuity conditions are satisfied at layer interfaces. The governing equations are derived from this model using a numerical technique called the least-squares finite element method (LSFEM). These LSFEMs seek to minimize the squares of the governing equations and the associated side conditions residuals over the computational domain. The model is comprised of layerwise variables such as displacements, out-of-plane stresses, and in- plane strains, treated as independent variables. Numerical results are presented to demonstrate the response of the laminated composite plates under various arbitrary boundary conditions using LSFEM and compared with the 3D elasticity solution available in the literature.展开更多
Boundary conditions for momentum and vorticity have been precisely derived, paying attention to the physical meaning of each mathematical expression of terms rigorously obtained from the basic equations: Navier-Stokes...Boundary conditions for momentum and vorticity have been precisely derived, paying attention to the physical meaning of each mathematical expression of terms rigorously obtained from the basic equations: Navier-Stokes equation and the equation of vorticity transport. It has been shown first that a contribution of fluid molecules crossing over a conceptual surface moving with fluid velocity due to their fluctuating motion is essentially important to understanding transport phenomena of momentum and vorticity. A notion of surface layers, which are thin layers at both sides of an interface, has been introduced next to elucidate the transporting mechanism of momentum and vorticity from one phase to the other at an interface through which no fluid molecules are crossing over. A fact that a size of δV, in which reliable values of density, momentum, and velocity of fluid are respectively defined as a volume-averaged mass of fluid molecules, a volume-averaged momentum of fluid molecules and a mass-averaged velocity of fluid molecules, is not infinitesimal but finite has been one of the key factors leading to the boundary conditions for vorticity at an interface between two fluids. The most distinguished characteristics of the boundary conditions derived here are the zero-value conditions for a normal component of momentum flux and tangential components of vorticity flux, at an interface.展开更多
Gastric cancer is the fifth most common cancer and in 2018,it was the third most common cause of cancer-related deaths worldwide.Endoscopic advances continue to be made for the diagnosis and management of both early g...Gastric cancer is the fifth most common cancer and in 2018,it was the third most common cause of cancer-related deaths worldwide.Endoscopic advances continue to be made for the diagnosis and management of both early gastric cancer and premalignant gastric conditions.In this review,we discuss the epidemiology and risk factors of gastric cancer and emphasize the differences in early vs latestage gastric cancer outcomes.We then discuss endoscopic advances in the diagnosis of early gastric cancer and premalignant gastric lesions.This includes the implementation of different imaging modalities such as narrow-band imaging,chromoendoscopy,confocal laser endomicroscopy,and other experimental techniques.We also discuss the use of endoscopic ultrasound in the diagnosis and staging of early gastric cancer.We then discuss the endoscopic advances made in the treatment of these conditions,including endoscopic mucosal resection,endoscopic submucosal dissection,and hybrid techniques such as laparoscopic endoscopic cooperative surgery.Finally,we comment on the current suggested recommendations for surveillance of both gastric cancer and its premalignant conditions.展开更多
The load spectrum is a crucial factor for assess-ing the fatigue reliability of in-service rolling element bear-ings in transmission systems.For a bearing in a high-speed train gearbox,a measurement technique based on...The load spectrum is a crucial factor for assess-ing the fatigue reliability of in-service rolling element bear-ings in transmission systems.For a bearing in a high-speed train gearbox,a measurement technique based on strain detection of bearing outer ring was used to instrument the bearing and determine the time histories of the distributed load in the bearing under different gear meshing conditions.Accordingly,the load spectrum of the total radial load car-ried by the bearing was compiled.The mean value and class interval of the obtained load spectrum were found to vary non-monotonously with the speed and torque of gear mesh-ing,which was considered to be caused by the vibration of the shaft and the bearing cage.As the realistic service load input of bearing life assessment,the measured load spectrum under different gear meshing conditions can be used to pre-dict gearbox bearing life realistically based on the damage-equivalent principle and actual operating conditions.展开更多
In this study, a morphodynamic numerical model is established with the Regional Ocean Modeling System(ROMS)to investigate the transient behavior of sand waves under realistic sea conditions. The simulation of sand wav...In this study, a morphodynamic numerical model is established with the Regional Ocean Modeling System(ROMS)to investigate the transient behavior of sand waves under realistic sea conditions. The simulation of sand wave evolution comprises two steps: 1) a regional-scale model is configured first to simulate the ocean hydrodynamics, i.e., tides and tidal currents, and 2) the transient behavior of sand waves is simulated in a small computational domain under the time-variant currents extracted from the large model. The evolution of sand waves on the continental shelf in the Beibu Gulf is specifically investigated. The numerical results of the two-year evolution of sand waves under normal sea conditions compare well with the field survey data. The transient behavior of sand waves in individual months shows that the sand waves are more stable in April and October than that in other months, which can be selected as the windows for seabed operations. The effects of sediment properties, including settling velocity, critical shear stress and surface erosion rate, on sand wave evolution are also analyzed. Then, the typhoon-induced currents are further superimposed on the tidal currents as the extreme weather conditions. Sand waves with the average wavelength generally have more active behavior than smaller or larger sand waves. The characteristics of the evolution of sand waves in an individual typhoon process are quite different for different hydrodynamic combinations. For the storm conditions, i.e., the real combination and maximum combination cases, the sand waves experience a significant migration together with a damping in height due to the dominant suspended sediment transport. For the mild conditions, i.e., the pure tidal current and minimum combination cases, the sand waves migrate less, but the heights continue growing due to the dominant bedload transport.展开更多
The oriental fruit fly,Bactrocera dorsalis(Hendel),is a devastating pest of citrus fruits.After successful mating,adult females insert their eggs into the ripened fruit,resulting in moldy and rotten fruit and causing ...The oriental fruit fly,Bactrocera dorsalis(Hendel),is a devastating pest of citrus fruits.After successful mating,adult females insert their eggs into the ripened fruit,resulting in moldy and rotten fruit and causing great economic losses for the citrus industry.In the field,flies initiate copulatory behaviors as twilight approaches,and decreasing light intensity in this period is the normal stimulus for copulation.In this study,ten light intensities ranging from 0–30000 lux were set to identify the typical intensity that strongly regulates the copulation behavior of B.dorsalis.Three light intensities found to regulate the copulation behavior were then selected to verify their effects on adult male wing fanning and female chemotaxis towards 2,3,5-trimethylpyrazine(TMP).At last,strong light and complete darkness were artificially combined in the lab to verify whether they could prevent copulation to inform behavioral manipulation of oriental flies in the future.The results indicated that adult flies generally initiated copulatory behaviors at low light intensity(<1000 lux).Stronger light significantly prevented copulation in proportion to intensity,with nearly no copulation events initiated when light intensity was above 20000 lux.Both male wing fanning and female chemotaxis towards TMP were attenuated as light intensity became stronger.However,at 10000 lux,males still fanned their wings to a certain extent while TMP completely lost its attractiveness to females.In the darkness,adults did not initiate any sexual behaviors,e.g.,copulation,wing fanning,or chemotaxis to TMP.One hour of strong light(10000 lux)combined with continuous darkness completely prevented mating.These results show that light condition is an essential factor for copulatory behaviors in the oriental fruit fly.Researchers could thus manipulate light conditions artificially or disrupt the molecular target in flies’light transduction pathway to develop environmentally-friendly techniques to control this pest.展开更多
Aptian is characterized by widespread deposition of organic-rich sediment.The Aptian bitumen limestone horizon,which is thin decimetre-thick sequences,locally crops out in the Kircaova area,Eastern Black Sea Region(Ea...Aptian is characterized by widespread deposition of organic-rich sediment.The Aptian bitumen limestone horizon,which is thin decimetre-thick sequences,locally crops out in the Kircaova area,Eastern Black Sea Region(Eastern Pontides).They are well correlated with Aptian bitumen limestone in the other Tethys Reams.They are proposed as episodes of increased organic matter.However,background factors controlling organic matter enrichment are poorly known.In this study,we present new inorganic geochemistry,including trace elements,rare earth elements(REE),redox-sensitive elements(RSE),stable-isotopes(δ~(18)O andδ~(13)C),and total organic carbon(TOC).We integrated new geochemical data with existing stratigraphy,paleontology,and organic chemistry data to provide new insight into the depositional environment and paleoclimate conditions during Aptian.The lacustrine bitumen limestone(LBL)samples have variedδ~(13)C(ave.-1.45‰)andδ~(18)O(ave.-4.50‰).They possess distinct REE patterns,with an average of REE(ave.14.45 ppm)and Y/Ho(ave.35)ratios.In addition,they have variable Nd/YbN(0.28-0.81;ave.0.56)and Ce/Ce*(0.68-0.97;ave.0.86),and relatively high Eu^(*)/Eu(1.23-1.53;ave.1.35).They display seawater signatures with reduced oxygen conditions.The enrichment in RSE(Mo,Cu,Ni,and Zn)and the low Mo/TOC(0.70-3.69;ave.2.41)support a certain degree of water restriction.The high Sr/Ba,Sr/Cu,Ga/Rb,and K/Al records of the LBL facies suggest hot house climatic conditions.The sedimentary environment was probably an isolated basin that is transformed from the marine basin.In addition to depositional conditions,the regional parameters such as the climate,increased run-off period,nutrient levels,alkalinity level,and dominant carbonate producers favored the enrichment in organic matter of LBL facies.Thus,extreme greenhouse palaeoclimate conditions have an important role in organic matter enrichment in the isolated basin.Our results are conformable with the published data from marine,semi-restricted basin,and lacustrine settings in the different parts of the Tethys margin.Thus,this approach provides the first insight into the Aptian greenhouse paleo-climate conditions of the Eastern Black Sea Region,NE Turkey.展开更多
Mesoporous titanium containing alumino-silicate materials with various titanium/silicon(Ti/Si) ratio(AlSi-Ti(n);n = Ti/Si mole ratio) have been successfully synthesized by a novel single-step sodium(Na)-free method, f...Mesoporous titanium containing alumino-silicate materials with various titanium/silicon(Ti/Si) ratio(AlSi-Ti(n);n = Ti/Si mole ratio) have been successfully synthesized by a novel single-step sodium(Na)-free method, for the first time. The obtained characterization results of the prepared materials reveal that in-situ addition of Ti into AlSi shows ordered mesoporous structure along with uniformly dispersed Ti species in +4 and +3 oxidation states suitable for selective oxidation of allylic C—H bond. The prepared mesoporouse Ti-AlSi(n) samples exhibited excellent activity in the oxidation of cyclohexene with 100%conversion and 100% selectivity to ketone-alcohol(KA) oil(cyclohex-2-en-1-ol and 2-cyclohexen-1-one) at low temperature and reaction time(35℃ and 30 min reaction time). This study suggests that AlSi-Ti(0.05) material can be a promising catalyst for the selective oxidation of cyclohexene under mild reaction conditions.展开更多
Successful breakthroughs have been made in shale oil exploration in several lacustrine basins in China,indicating a promising future for shale oil exploration and production.Current exploration results have revealed t...Successful breakthroughs have been made in shale oil exploration in several lacustrine basins in China,indicating a promising future for shale oil exploration and production.Current exploration results have revealed the following major conditions of lacustrine shale oil accumulation:(1)stable and widely distributed shale with a high organic abundance and appropriate thermal maturity acts as a fundamental basis for shale oil retention.This shale exhibits several critical parameters,such as total organic carbon content greater than 2%,with optimal values ranging from 3% to 4%,kerogen Ⅰ and Ⅱ_(1) as the dominant organic matter types,and vitrinite reflectance(R_(o))values greater than 0.9%(0.8% for brackish water environments).(2)Various types of reservoirs exhibiting brittleness and a certain volume of micro-nanoscale pores are critical conditions for shale oil accumulation,and these reservoirs have porosities greater than 3% to 6%.Moreover,when diagenesis is incipient,pure shales are not favorable for medium-to-high maturity shale oil enrichment,whereas tight sandstone and hybrid rocks with clay content less than 20% are favorable;however,for medium-to-late-stage diagenesis,pure shales with a clay content of 40% are favorable.(3)The retention of a large amount of high-quality hydrocarbons is the factor that best guarantees shale oil accumulation with good mobility.Free hydrocarbon content exceeding a threshold value of 2 mg/g is generally required,and the optimum value is 4 mg/g to 6 mg/g.Moreover,a gas-oil ratio exceeding a threshold value of 80 m^(3)/m^(3) is required,with the optimal value ranging from 150 m^(3)/m^(3) to 300 m^(3)/m^(3).(4)High-quality roof and floor sealing conditions are essential for the shale oil enrichment interval to maintain the overpressure and retain a sufficient amount of hydrocarbons with good quality.Lacustrine shale oil distributions exhibit the following characteristics:(1)major enrichment areas of shale oil are located in semi-deep to deep lacustrine depositional areas with external materials,such as volcanic ash fallout,hydrothermal solutions,and radioactive substances with catalytic action,as inputs;(2)intervals with“four high values and one preservation condition”govern the distribution of shale oil enrichment intervals;and(3)favorable assemblages of lithofacies/lithologies determine the distribution of enrichment area.According to preliminary estimates,China has 131×10^(8) to 163×10^(8) t of total shale oil resources with medium-to-high thermal maturity,among which 67×10^(8) to 84×10^(8) t is commercial.These resources are primarily located in the Chang 7^(1+2) interval in the Ordos Basin,Qing 1+2 members in Gulong sag in the Songliao Basin,Kongdian and Shahejie formations of Cangdong sag,Qikou sag and the Jiyang depression in the Bohai Bay Basin,and Lucaogou Formation in the Junggar Basin.展开更多
Let?denote a smooth,bounded domain in R^(N)(N≥2).Suppose that g is a nondecreasing C^(1)positive function and assume that b(x)is continuous and nonnegative inΩ,and that it may be singular on■Ω.In this paper,we pro...Let?denote a smooth,bounded domain in R^(N)(N≥2).Suppose that g is a nondecreasing C^(1)positive function and assume that b(x)is continuous and nonnegative inΩ,and that it may be singular on■Ω.In this paper,we provide sufficient and necessary conditions on the existence of boundary blow-up solutions to the p-Laplacian problem△_(p)u=b(x)g(u)for x∈Ω,u(x)→+∞as dist(x,■Ω)→0.The estimates of such solutions are also investigated.Moreover,when b has strong singularity,the nonexistence of boundary blow-up(radial)solutions and infinitely many radial solutions are also considered.展开更多
With the increasing depth of coal mining,the requirements for coring devices that maintain pressure are increasing.To adapt to the special environment in deep coal seams and improve the accuracy of testing gas content...With the increasing depth of coal mining,the requirements for coring devices that maintain pressure are increasing.To adapt to the special environment in deep coal seams and improve the accuracy of testing gas content,a low-disturbance pressure-preserving corer was developed.The measurement of gas content using this corer was analyzed.The coring test platform was used to complete a coring function test.A pressurized core with a diameter of 50 mm was obtained.The pressure was 0.15 MPa,which was equal to the pressure of the liquid column of the cored layer,indicating that the corer can be successfully used in a mud environment.Next,a pressure test of the corer was conducted.The results showed that under conditions of low pressure(8 MPa)and high pressure(25 MPa),the internal pressure of the corer remained stable for more than 1 h,indicating that the corer has good ability to maintain pressure.Therefore,the corer can be applied at deep coal mine sites.The results of this research can be used to promote the safe exploitation of deep coal mines and the exploitation of methane resources in coalbeds.展开更多
We study the space of stability conditions on K3 surfaces from the perspective of mirror symmetry. This is done in the attractor backgrounds(moduli). We find certain highly non-generic behaviors of marginal stability ...We study the space of stability conditions on K3 surfaces from the perspective of mirror symmetry. This is done in the attractor backgrounds(moduli). We find certain highly non-generic behaviors of marginal stability walls(a key notion in the study of wall crossings)in the space of stability conditions. These correspond via mirror symmetry to some nongeneric behaviors of special Lagrangians in an attractor background. The main results can be understood as a mirror correspondence in a synthesis of the homological mirror conjecture and SYZ mirror conjecture.展开更多
The utilization of solar energy is essential to all living things since the beginning of time.In addition to being a constant source of energy,solar energy(SE)can also be used to generate heat and electricity.Recent t...The utilization of solar energy is essential to all living things since the beginning of time.In addition to being a constant source of energy,solar energy(SE)can also be used to generate heat and electricity.Recent technology enables to convert the solar energy into electricity by using thermal solar heat.Solar energy is perhaps the most easily accessible and plentiful source of sustainable energy.Copper-based nanofluid has been considered as a method to improve solar collector performance by absorbing incoming solar energy directly.The goal of this research is to explore theoretically the Agrawal axisymmetric flow induced by Cu-water nanofluid over a moving permeable disk caused by solar energy.Moreover,the impacts of Maxwell velocity and Smoluchowski temperature slip are incorporated to discuss the fine points of nanofluid flow and characteristics of heat transfer.The primary partial differential equations are transformed to similarity equations by employing similarity variables and then utilizing bvp4c to resolve the set of equations numerically.The current numerical approach can produce double solutions by providing suitable initial guesses.In addition,the results revealed that the impact of solar collector efficiency enhances significantly due to nanoparticle volume fraction.The suction parameter delays the boundary layer separation.Moreover,stability analysis is performed and is found that the upper solution is stable and physically trustworthy while the lower one is unstable.展开更多
基金the National Natural Science Foundation of China(Grant No.U20A2081)West Light Foundation of the Chinese Academy of Sciences(Grant No.xbzg-zdsys-202102)the Second Tibetan Plateau Scientific Expedition and Research(STEP)Project(Grant No.2019QZKK0105).
文摘Accurate initial soil conditions play a crucial role in simulating soil hydrothermal and surface energy fluxes in land surface process modeling.This study emphasized the influence of the initial soil temperature(ST)and soil moisture(SM)conditions on a land surface energy and water simulation in the permafrost region in the Tibetan Plateau(TP)using the Community Land Model version 5.0(CLM5.0).The results indicate that the default initial schemes for ST and SM in CLM5.0 were simplistic,and inaccurately represented the soil characteristics of permafrost in the TP which led to underestimating ST during the freezing period while overestimating ST and underestimating SLW during the thawing period at the XDT site.Applying the long-term spin-up method to obtain initial soil conditions has only led to limited improvement in simulating soil hydrothermal and surface energy fluxes.The modified initial soil schemes proposed in this study comprehensively incorporate the characteristics of permafrost,which coexists with soil liquid water(SLW),and soil ice(SI)when the ST is below freezing temperature,effectively enhancing the accuracy of the simulated soil hydrothermal and surface energy fluxes.Consequently,the modified initial soil schemes greatly improved upon the results achieved through the long-term spin-up method.Three modified initial soil schemes experiments resulted in a 64%,88%,and 77%reduction in the average mean bias error(MBE)of ST,and a 13%,21%,and 19%reduction in the average root-mean-square error(RMSE)of SLW compared to the default simulation results.Also,the average MBE of net radiation was reduced by 7%,22%,and 21%.
基金supported by the project of the China Geological Survey for shale gas in Southern China(DD20221852)the National Natural Science Foundation of China(42242010,U2244208)。
文摘China is home to shales of three facies:Marine shale,continental shale,and marine-continental transitional shale.Different types of shale gas are associated with significantly different formation conditions and major controlling factors.This study compared the geological characteristics of various shales and analyzed the influences of different parameters on the formation and accumulation of shale gas.In general,shales in China’s several regions exhibit high total organic carbon(TOC)contents,which lays a sound material basis for shale gas generation.Marine strata generally show high degrees of thermal evolution.In contrast,continental shales manifest low degrees of thermal evolution,necessitating focusing on areas with relatively high degrees of thermal evolution in the process of shale gas surveys for these shales.The shales of the Wufeng and Silurian formations constitute the most favorable shale gas reservoirs since they exhibit the highest porosity among the three types of shales.These shales are followed by those in the Niutitang and Longtan formations.In contrast,the shales of the Doushantuo,Yanchang,and Qingshankou formations manifest low porosities.Furthermore,the shales of the Wufeng and Longmaxi formations exhibit high brittle mineral contents.Despite a low siliceous mineral content,the shales of the Doushantuo Formation feature a high carbonate mineral content,which can increase the shales’brittleness to some extent.For marine-continental transitional shales,where thin interbeds of tight sandstone with unequal thicknesses are generally found,it is recommended that fracturing combined with drainage of multiple sets of lithologic strata should be employed to enhance their shale gas production.
基金Project supported by the National Natural Science Foundation of China (Nos. 52075070 and12302254)the Dalian City Supports Innovation and Entrepreneurship Projects for High-Level Talents (No. 2021RD16)the Liaoning Revitalization Talents Program (No. XLYC2002108)。
文摘The determination of the ultimate load-bearing capacity of structures made of elastoplastic heterogeneous materials under varying loads is of great importance for engineering analysis and design. Therefore, it is necessary to accurately predict the shakedown domains of these materials. The static shakedown theorem, also known as Melan's theorem, is a fundamental method used to predict the shakedown domains of structures and materials. Within this method, a key aspect lies in the construction and application of an appropriate self-equilibrium stress field(SSF). In the structural shakedown analysis, the SSF is typically constructed by governing equations that satisfy no external force(NEF) boundary conditions. However, we discover that directly applying these governing equations is not suitable for the shakedown analysis of heterogeneous materials. Researchers must consider the requirements imposed by the Hill-Mandel condition for boundary conditions and the physical significance of representative volume elements(RVEs). This paper addresses this issue and demonstrates that the sizes of SSFs vary under different boundary conditions, such as uniform displacement boundary conditions(DBCs), uniform traction boundary conditions(TBCs), and periodic boundary conditions(PBCs). As a result, significant discrepancies arise in the predicted shakedown domain sizes of heterogeneous materials. Built on the demonstrated relationship between SSFs under different boundary conditions, this study explores the conservative relationships among different shakedown domains, and provides proof of the relationship between the elastic limit(EL) factors and the shakedown loading factors under the loading domain of two load vertices. By utilizing numerical examples, we highlight the conservatism present in certain results reported in the existing literature. Among the investigated boundary conditions, the obtained shakedown domain is the most conservative under TBCs.Conversely, utilizing PBCs to construct an SSF for the shakedown analysis leads to less conservative lower bounds, indicating that PBCs should be employed as the preferred boundary conditions for the shakedown analysis of heterogeneous materials.
文摘This study aims to quantify the susceptibility of granular materials used in pavements to changes in moisture content and propose a correlation model to incorporate this susceptibility into seasonal analyses.The fines content and the percentage of fractured coarse aggregates were identified as direct indicators of the resilient modulus susceptibility to changes in water content.The results showed that the percentage of fractured coarse aggregates particles(FR)has a more significant impact on the resilient modulus(Er)of crushed granular materials used in pavement construction than the combined indicator of the fines content and sample volumetrics(nf).Crushed granular materials with a higher percentage of fractured coarse aggregates are relatively insensitive to changes in the degree of saturation,but become more sensitive as the fine fraction porosity decreases.An adjusted model was proposed based on the existing formulation,but considers a complex parameter to describe and adjust the sensitivity of base granular materials to variations in moisture content with respect to fabrication charac-teristics,fines content and volumetric properties.The model shows that the variation of Er values is below10%for fully crushed granular materials.However,it reaches approximately±12%for materials with 75%of crushed coarse aggregates andþ40%and-25%for materials with FR=50%.This model could help select good ag-gregates characteristics and adjust grain-size distribution for environments where significant moisture content variations can occur in the pavement system,such as in the Province of Quebec(Canada).As it is based on pa-rameters that can be easily determined or estimated,it also represents a valuable tool for detailed design and analysis that can consider material characteristics.
文摘A photovoltaic (PV) string with multiple modules with bypass diodes frequently deployed on a variety of autonomous PV systems may present multiple power peaks under uneven shading. For optimal solar harvesting, there is a need for a control schema to force the PV string to operate at global maximum power point (GMPP). While a lot of tracking methods have been proposed in the literature, they are usually complex and do not fully take advantage of the available characteristics of the PV array. This work highlights how the voltage at operating point and the forward voltage of the bypass diode are considered to design a global maximum power point tracking (GMPPT) algorithm with a very limited global search phase called Fast GMPPT. This algorithm successfully tracks GMPP between 94% and 98% of the time under a theoretical evaluation. It is then compared against Perturb and Observe, Deterministic Particle Swarm Optimization, and Grey Wolf Optimization under a sequence of irradiance steps as well as a power-over-voltage characteristics profile that mimics the electrical characteristics of a PV string under varying partial shading conditions. Overall, the simulation with the sequence of irradiance steps shows that while Fast GMPPT does not have the best convergence time, it has an excellent convergence rate as well as causes the least amount of power loss during the global search phase. Experimental test under varying partial shading conditions shows that while the GMPPT proposal is simple and lightweight, it is very performant under a wide range of dynamically varying partial shading conditions and boasts the best energy efficiency (94.74%) out of the 4 tested algorithms.
文摘In this paper, the inverse spectral problem of Sturm-Liouville operator with boundary conditions and jump conditions dependent on the spectral parameter is investigated. Firstly, the self-adjointness of the problem and the eigenvalue properties are given, then the asymptotic formulas of eigenvalues and eigenfunctions are presented. Finally, the uniqueness theorems of the corresponding inverse problems are given by Weyl function theory and inverse spectral data approach.
文摘Background:Persons with mental disorders are at a higher risk than the general population for the subsequent development of certain medical conditions.Methods:We used a population-based cohort from Danish national registries that included data on more than 5.9 million persons born in Denmark from 1900 through 2015 and followed them from 2000 through 2016,for a total of 83.9 million person-years.
文摘Laminated composites are widely used in many engineering industries such as aircraft, spacecraft, boat hulls, racing car bodies, and storage tanks. We analyze the 3D deformations of a multilayered, linear elastic, anisotropic rectangular plate subjected to arbitrary boundary conditions on one edge and simply supported on other edge. The rectangular laminate consists of anisotropic and homogeneous laminae of arbitrary thicknesses. This study presents the elastic analysis of laminated composite plates subjected to sinusoidal mechanical loading under arbitrary boundary conditions. Least square finite element solutions for displacements and stresses are investigated using a mathematical model, called a state-space model, which allows us to simultaneously solve for these field variables in the composite structure’s domain and ensure that continuity conditions are satisfied at layer interfaces. The governing equations are derived from this model using a numerical technique called the least-squares finite element method (LSFEM). These LSFEMs seek to minimize the squares of the governing equations and the associated side conditions residuals over the computational domain. The model is comprised of layerwise variables such as displacements, out-of-plane stresses, and in- plane strains, treated as independent variables. Numerical results are presented to demonstrate the response of the laminated composite plates under various arbitrary boundary conditions using LSFEM and compared with the 3D elasticity solution available in the literature.
文摘Boundary conditions for momentum and vorticity have been precisely derived, paying attention to the physical meaning of each mathematical expression of terms rigorously obtained from the basic equations: Navier-Stokes equation and the equation of vorticity transport. It has been shown first that a contribution of fluid molecules crossing over a conceptual surface moving with fluid velocity due to their fluctuating motion is essentially important to understanding transport phenomena of momentum and vorticity. A notion of surface layers, which are thin layers at both sides of an interface, has been introduced next to elucidate the transporting mechanism of momentum and vorticity from one phase to the other at an interface through which no fluid molecules are crossing over. A fact that a size of δV, in which reliable values of density, momentum, and velocity of fluid are respectively defined as a volume-averaged mass of fluid molecules, a volume-averaged momentum of fluid molecules and a mass-averaged velocity of fluid molecules, is not infinitesimal but finite has been one of the key factors leading to the boundary conditions for vorticity at an interface between two fluids. The most distinguished characteristics of the boundary conditions derived here are the zero-value conditions for a normal component of momentum flux and tangential components of vorticity flux, at an interface.
文摘Gastric cancer is the fifth most common cancer and in 2018,it was the third most common cause of cancer-related deaths worldwide.Endoscopic advances continue to be made for the diagnosis and management of both early gastric cancer and premalignant gastric conditions.In this review,we discuss the epidemiology and risk factors of gastric cancer and emphasize the differences in early vs latestage gastric cancer outcomes.We then discuss endoscopic advances in the diagnosis of early gastric cancer and premalignant gastric lesions.This includes the implementation of different imaging modalities such as narrow-band imaging,chromoendoscopy,confocal laser endomicroscopy,and other experimental techniques.We also discuss the use of endoscopic ultrasound in the diagnosis and staging of early gastric cancer.We then discuss the endoscopic advances made in the treatment of these conditions,including endoscopic mucosal resection,endoscopic submucosal dissection,and hybrid techniques such as laparoscopic endoscopic cooperative surgery.Finally,we comment on the current suggested recommendations for surveillance of both gastric cancer and its premalignant conditions.
基金This research was supported by the Joint Funds of the National Natural Science Foundation of China(Grant No.U1834202).
文摘The load spectrum is a crucial factor for assess-ing the fatigue reliability of in-service rolling element bear-ings in transmission systems.For a bearing in a high-speed train gearbox,a measurement technique based on strain detection of bearing outer ring was used to instrument the bearing and determine the time histories of the distributed load in the bearing under different gear meshing conditions.Accordingly,the load spectrum of the total radial load car-ried by the bearing was compiled.The mean value and class interval of the obtained load spectrum were found to vary non-monotonously with the speed and torque of gear mesh-ing,which was considered to be caused by the vibration of the shaft and the bearing cage.As the realistic service load input of bearing life assessment,the measured load spectrum under different gear meshing conditions can be used to pre-dict gearbox bearing life realistically based on the damage-equivalent principle and actual operating conditions.
基金financially supported by the National Natural Science Foundation of China (Grant Nos. 51579232 and 51890913)the Open Funding of State Key Laboratory of Hydraulic Engineering Simulation and Safety (Grant No. HESS-1712)。
文摘In this study, a morphodynamic numerical model is established with the Regional Ocean Modeling System(ROMS)to investigate the transient behavior of sand waves under realistic sea conditions. The simulation of sand wave evolution comprises two steps: 1) a regional-scale model is configured first to simulate the ocean hydrodynamics, i.e., tides and tidal currents, and 2) the transient behavior of sand waves is simulated in a small computational domain under the time-variant currents extracted from the large model. The evolution of sand waves on the continental shelf in the Beibu Gulf is specifically investigated. The numerical results of the two-year evolution of sand waves under normal sea conditions compare well with the field survey data. The transient behavior of sand waves in individual months shows that the sand waves are more stable in April and October than that in other months, which can be selected as the windows for seabed operations. The effects of sediment properties, including settling velocity, critical shear stress and surface erosion rate, on sand wave evolution are also analyzed. Then, the typhoon-induced currents are further superimposed on the tidal currents as the extreme weather conditions. Sand waves with the average wavelength generally have more active behavior than smaller or larger sand waves. The characteristics of the evolution of sand waves in an individual typhoon process are quite different for different hydrodynamic combinations. For the storm conditions, i.e., the real combination and maximum combination cases, the sand waves experience a significant migration together with a damping in height due to the dominant suspended sediment transport. For the mild conditions, i.e., the pure tidal current and minimum combination cases, the sand waves migrate less, but the heights continue growing due to the dominant bedload transport.
基金supported by the Shenzhen Science and Technology Program,China(KQTD20180411143628272)the Special Funds for Science Technology Innovation and Industrial Development of Shenzhen Dapeng New District,China(PT202101-02).
文摘The oriental fruit fly,Bactrocera dorsalis(Hendel),is a devastating pest of citrus fruits.After successful mating,adult females insert their eggs into the ripened fruit,resulting in moldy and rotten fruit and causing great economic losses for the citrus industry.In the field,flies initiate copulatory behaviors as twilight approaches,and decreasing light intensity in this period is the normal stimulus for copulation.In this study,ten light intensities ranging from 0–30000 lux were set to identify the typical intensity that strongly regulates the copulation behavior of B.dorsalis.Three light intensities found to regulate the copulation behavior were then selected to verify their effects on adult male wing fanning and female chemotaxis towards 2,3,5-trimethylpyrazine(TMP).At last,strong light and complete darkness were artificially combined in the lab to verify whether they could prevent copulation to inform behavioral manipulation of oriental flies in the future.The results indicated that adult flies generally initiated copulatory behaviors at low light intensity(<1000 lux).Stronger light significantly prevented copulation in proportion to intensity,with nearly no copulation events initiated when light intensity was above 20000 lux.Both male wing fanning and female chemotaxis towards TMP were attenuated as light intensity became stronger.However,at 10000 lux,males still fanned their wings to a certain extent while TMP completely lost its attractiveness to females.In the darkness,adults did not initiate any sexual behaviors,e.g.,copulation,wing fanning,or chemotaxis to TMP.One hour of strong light(10000 lux)combined with continuous darkness completely prevented mating.These results show that light condition is an essential factor for copulatory behaviors in the oriental fruit fly.Researchers could thus manipulate light conditions artificially or disrupt the molecular target in flies’light transduction pathway to develop environmentally-friendly techniques to control this pest.
文摘Aptian is characterized by widespread deposition of organic-rich sediment.The Aptian bitumen limestone horizon,which is thin decimetre-thick sequences,locally crops out in the Kircaova area,Eastern Black Sea Region(Eastern Pontides).They are well correlated with Aptian bitumen limestone in the other Tethys Reams.They are proposed as episodes of increased organic matter.However,background factors controlling organic matter enrichment are poorly known.In this study,we present new inorganic geochemistry,including trace elements,rare earth elements(REE),redox-sensitive elements(RSE),stable-isotopes(δ~(18)O andδ~(13)C),and total organic carbon(TOC).We integrated new geochemical data with existing stratigraphy,paleontology,and organic chemistry data to provide new insight into the depositional environment and paleoclimate conditions during Aptian.The lacustrine bitumen limestone(LBL)samples have variedδ~(13)C(ave.-1.45‰)andδ~(18)O(ave.-4.50‰).They possess distinct REE patterns,with an average of REE(ave.14.45 ppm)and Y/Ho(ave.35)ratios.In addition,they have variable Nd/YbN(0.28-0.81;ave.0.56)and Ce/Ce*(0.68-0.97;ave.0.86),and relatively high Eu^(*)/Eu(1.23-1.53;ave.1.35).They display seawater signatures with reduced oxygen conditions.The enrichment in RSE(Mo,Cu,Ni,and Zn)and the low Mo/TOC(0.70-3.69;ave.2.41)support a certain degree of water restriction.The high Sr/Ba,Sr/Cu,Ga/Rb,and K/Al records of the LBL facies suggest hot house climatic conditions.The sedimentary environment was probably an isolated basin that is transformed from the marine basin.In addition to depositional conditions,the regional parameters such as the climate,increased run-off period,nutrient levels,alkalinity level,and dominant carbonate producers favored the enrichment in organic matter of LBL facies.Thus,extreme greenhouse palaeoclimate conditions have an important role in organic matter enrichment in the isolated basin.Our results are conformable with the published data from marine,semi-restricted basin,and lacustrine settings in the different parts of the Tethys margin.Thus,this approach provides the first insight into the Aptian greenhouse paleo-climate conditions of the Eastern Black Sea Region,NE Turkey.
文摘Mesoporous titanium containing alumino-silicate materials with various titanium/silicon(Ti/Si) ratio(AlSi-Ti(n);n = Ti/Si mole ratio) have been successfully synthesized by a novel single-step sodium(Na)-free method, for the first time. The obtained characterization results of the prepared materials reveal that in-situ addition of Ti into AlSi shows ordered mesoporous structure along with uniformly dispersed Ti species in +4 and +3 oxidation states suitable for selective oxidation of allylic C—H bond. The prepared mesoporouse Ti-AlSi(n) samples exhibited excellent activity in the oxidation of cyclohexene with 100%conversion and 100% selectivity to ketone-alcohol(KA) oil(cyclohex-2-en-1-ol and 2-cyclohexen-1-one) at low temperature and reaction time(35℃ and 30 min reaction time). This study suggests that AlSi-Ti(0.05) material can be a promising catalyst for the selective oxidation of cyclohexene under mild reaction conditions.
基金Major Project of National Natural Science Foundation of China(42090020,42090025)Major Project of CNPC(2019E-2601)。
文摘Successful breakthroughs have been made in shale oil exploration in several lacustrine basins in China,indicating a promising future for shale oil exploration and production.Current exploration results have revealed the following major conditions of lacustrine shale oil accumulation:(1)stable and widely distributed shale with a high organic abundance and appropriate thermal maturity acts as a fundamental basis for shale oil retention.This shale exhibits several critical parameters,such as total organic carbon content greater than 2%,with optimal values ranging from 3% to 4%,kerogen Ⅰ and Ⅱ_(1) as the dominant organic matter types,and vitrinite reflectance(R_(o))values greater than 0.9%(0.8% for brackish water environments).(2)Various types of reservoirs exhibiting brittleness and a certain volume of micro-nanoscale pores are critical conditions for shale oil accumulation,and these reservoirs have porosities greater than 3% to 6%.Moreover,when diagenesis is incipient,pure shales are not favorable for medium-to-high maturity shale oil enrichment,whereas tight sandstone and hybrid rocks with clay content less than 20% are favorable;however,for medium-to-late-stage diagenesis,pure shales with a clay content of 40% are favorable.(3)The retention of a large amount of high-quality hydrocarbons is the factor that best guarantees shale oil accumulation with good mobility.Free hydrocarbon content exceeding a threshold value of 2 mg/g is generally required,and the optimum value is 4 mg/g to 6 mg/g.Moreover,a gas-oil ratio exceeding a threshold value of 80 m^(3)/m^(3) is required,with the optimal value ranging from 150 m^(3)/m^(3) to 300 m^(3)/m^(3).(4)High-quality roof and floor sealing conditions are essential for the shale oil enrichment interval to maintain the overpressure and retain a sufficient amount of hydrocarbons with good quality.Lacustrine shale oil distributions exhibit the following characteristics:(1)major enrichment areas of shale oil are located in semi-deep to deep lacustrine depositional areas with external materials,such as volcanic ash fallout,hydrothermal solutions,and radioactive substances with catalytic action,as inputs;(2)intervals with“four high values and one preservation condition”govern the distribution of shale oil enrichment intervals;and(3)favorable assemblages of lithofacies/lithologies determine the distribution of enrichment area.According to preliminary estimates,China has 131×10^(8) to 163×10^(8) t of total shale oil resources with medium-to-high thermal maturity,among which 67×10^(8) to 84×10^(8) t is commercial.These resources are primarily located in the Chang 7^(1+2) interval in the Ordos Basin,Qing 1+2 members in Gulong sag in the Songliao Basin,Kongdian and Shahejie formations of Cangdong sag,Qikou sag and the Jiyang depression in the Bohai Bay Basin,and Lucaogou Formation in the Junggar Basin.
基金supported by the Beijing Natural Science Foundation(1212003)。
文摘Let?denote a smooth,bounded domain in R^(N)(N≥2).Suppose that g is a nondecreasing C^(1)positive function and assume that b(x)is continuous and nonnegative inΩ,and that it may be singular on■Ω.In this paper,we provide sufficient and necessary conditions on the existence of boundary blow-up solutions to the p-Laplacian problem△_(p)u=b(x)g(u)for x∈Ω,u(x)→+∞as dist(x,■Ω)→0.The estimates of such solutions are also investigated.Moreover,when b has strong singularity,the nonexistence of boundary blow-up(radial)solutions and infinitely many radial solutions are also considered.
基金supported by the National Natural Science Foundation of China(No.51827901)the National Natural Science Foundation of China(No.52225403)+1 种基金the Program for Guangdong Introducing Innovative and Entrepreneurial Teams of China(No.2019ZT08G315)the Sichuan Science and Technology Program of China(No.2023NSFSC0780).
文摘With the increasing depth of coal mining,the requirements for coring devices that maintain pressure are increasing.To adapt to the special environment in deep coal seams and improve the accuracy of testing gas content,a low-disturbance pressure-preserving corer was developed.The measurement of gas content using this corer was analyzed.The coring test platform was used to complete a coring function test.A pressurized core with a diameter of 50 mm was obtained.The pressure was 0.15 MPa,which was equal to the pressure of the liquid column of the cored layer,indicating that the corer can be successfully used in a mud environment.Next,a pressure test of the corer was conducted.The results showed that under conditions of low pressure(8 MPa)and high pressure(25 MPa),the internal pressure of the corer remained stable for more than 1 h,indicating that the corer has good ability to maintain pressure.Therefore,the corer can be applied at deep coal mine sites.The results of this research can be used to promote the safe exploitation of deep coal mines and the exploitation of methane resources in coalbeds.
文摘We study the space of stability conditions on K3 surfaces from the perspective of mirror symmetry. This is done in the attractor backgrounds(moduli). We find certain highly non-generic behaviors of marginal stability walls(a key notion in the study of wall crossings)in the space of stability conditions. These correspond via mirror symmetry to some nongeneric behaviors of special Lagrangians in an attractor background. The main results can be understood as a mirror correspondence in a synthesis of the homological mirror conjecture and SYZ mirror conjecture.
基金supported by Researchers Supporting Project No.(RSP-2021/33),King Saud University,Riyadh,Saudi Arabia.
文摘The utilization of solar energy is essential to all living things since the beginning of time.In addition to being a constant source of energy,solar energy(SE)can also be used to generate heat and electricity.Recent technology enables to convert the solar energy into electricity by using thermal solar heat.Solar energy is perhaps the most easily accessible and plentiful source of sustainable energy.Copper-based nanofluid has been considered as a method to improve solar collector performance by absorbing incoming solar energy directly.The goal of this research is to explore theoretically the Agrawal axisymmetric flow induced by Cu-water nanofluid over a moving permeable disk caused by solar energy.Moreover,the impacts of Maxwell velocity and Smoluchowski temperature slip are incorporated to discuss the fine points of nanofluid flow and characteristics of heat transfer.The primary partial differential equations are transformed to similarity equations by employing similarity variables and then utilizing bvp4c to resolve the set of equations numerically.The current numerical approach can produce double solutions by providing suitable initial guesses.In addition,the results revealed that the impact of solar collector efficiency enhances significantly due to nanoparticle volume fraction.The suction parameter delays the boundary layer separation.Moreover,stability analysis is performed and is found that the upper solution is stable and physically trustworthy while the lower one is unstable.