Mixed matrix membranes(MMMs)could combine the advantages of both polymeric membranes and porousfillers,making them an effective alternative to conventional polymer membranes.However,interfacial incompatibility issues,s...Mixed matrix membranes(MMMs)could combine the advantages of both polymeric membranes and porousfillers,making them an effective alternative to conventional polymer membranes.However,interfacial incompatibility issues,such as the presence of interfacial voids,hardening of polymer chains,and blockage of micropores by polymers between common MMMsfillers and the polymer matrix,currently limit the gas sep-aration performance of MMMs.Ternary phase MMMs(consisting of afiller,an additive,and a matrix)made by adding a third compound,usually functionalized additives,can overcome the structural problems of binary phase MMMs and positively impact membrane separation performance.This review introduces the structure and fabrication processes for ternary MMMs,categorizes various nanofillers and the third component,and summarizes and analyzes in detail the CO_(2) separation performance of newly developed ternary MMMs based on both rubbery and glassy polymers.Based on this separation data,the challenges of ternary MMMs are also discussed.Finally,future directions for ternary MMMs are proposed.展开更多
氮化硅是一种良好的载体,具有较高的水热稳定性和机械稳定性,其表面的氨基基团能够较好地锚定金属,显著提高金属分散度。但是,商品氮化硅比表面积较低,对金属分散作用仍然有限。因此,以自制的高比表面积氮化硅(Si_(3)N_(4))为载体,通过...氮化硅是一种良好的载体,具有较高的水热稳定性和机械稳定性,其表面的氨基基团能够较好地锚定金属,显著提高金属分散度。但是,商品氮化硅比表面积较低,对金属分散作用仍然有限。因此,以自制的高比表面积氮化硅(Si_(3)N_(4))为载体,通过浸渍法制备了不同Ru负载量(质量分数分别为0.5%、1.0%和2.0%)的催化剂(分别为0.5%Ru/Si_(3)N_(4)、1.0%Ru/Si_(3)N_(4)和2.0%Ru/Si_(3)N_(4)),并以商品氮化硅(Si_(3)N_(4)-C)为载体制备了2.0%Ru/Si_(3)N_(4)-C催化剂作为对照组。表征了催化剂的理化性质,测试了其在300℃、0.1 MPa下的CO_(2)加氢反应活性。结果显示,与Si_(3)N_(4)-C相比,Si_(3)N_(4)的比表面积较高(502 m^(2)/g),Si_(3)N_(4)作为载体显著提高了金属分散度,降低了金属粒径,催化剂暴露出更多的活性位点。0.5%Ru/Si_(3)N_(4)的金属粒径较小,展现出强的H_(2)吸附能力,H难以解吸,抑制了中间物种CO加氢生成CH_(4)。随着Ru负载量增加,金属粒径增大,催化剂的CH_(4)选择性更好。Ru/Si_(3)N_(4)系列催化剂中,2.0%Ru/Si_(3)N_(4)的CH_(4)选择性较高(98.8%)。空速为10000 m L/(g·h)时,0.5%Ru/Si_(3)N_(4)的CO选择性为88.2%。与2.0%Ru/Si_(3)N_(4)相比,2.0%Ru/Si_(3)N_(4)-C的金属粒径更大,活性位点较少,活性更低。2.0%Ru/Si_(3)N_(4)和2.0%Ru/Si_(3)N_(4)-C的CO_(2)转化率分别为53.1%和9.2%。Si_(3)N_(4)有效提高了金属分散度,提高了催化剂的CO_(2)加氢反应活性;通过调控Ru负载量控制催化剂金属粒径,可实现对产物CO或CH_(4)选择性的调控。展开更多
"Carbon peaking and carbon neutrality"is an essential national strategy,and the geological storage and utilization of CO_(2)is a hot issue today.However,due to the scarcity of pure CO_(2)gas sources in China..."Carbon peaking and carbon neutrality"is an essential national strategy,and the geological storage and utilization of CO_(2)is a hot issue today.However,due to the scarcity of pure CO_(2)gas sources in China and the high cost of CO_(2)capture,CO_(2)-rich industrial waste gas(CO_(2)-rich IWG)is gradually emerging into the public's gaze.CO_(2)has good adsorption properties on shale surfaces,but acidic gases can react with shale,so the mechanism of the CO_(2)-rich IWG-water-shale reaction and the change in reservoir properties will determine the stability of geological storage.Therefore,based on the mineral composition of the Longmaxi Formation shale,this study constructs a thermodynamic equilibrium model of water-rock reactions and simulates the regularity of reactions between CO_(2)-rich IWG and shale minerals.The results indicate that CO_(2)consumed 12%after reaction,and impurity gases in the CO_(2)-rich IWG can be dissolved entirely,thus demonstrating the feasibility of treating IWG through water-rock reactions.Since IWG inhibits the dissolution of CO_(2),the optimal composition of CO_(2)-rich IWG is 95%CO_(2)and 5%IWG when CO_(2)geological storage is the main goal.In contrast,when the main goal is the geological storage of total CO_(2)-rich IWG or impurity gas,the optimal CO_(2)-rich IWG composition is 50%CO_(2)and 50%IWG.In the CO_(2)-rich IWG-water-shale reaction,temperature has less influence on the water-rock reaction,while pressure is the most important parameter.SO2 has the greatest impact on water-rock reaction in gas.For minerals,clay minerals such as illite and montmorillonite had a significant effect on water-rock reaction.The overall reaction is dominated by precipitation and the volume of the rock skeleton has increased by 0.74 cm3,resulting in a decrease in shale porosity,which enhances the stability of CO_(2)geological storage to some extent.During the reaction between CO_(2)-rich IWG-water-shale at simulated temperatures and pressures,precipitation is the main reaction,and shale porosity decreases.However,as the reservoir water content increases,the reaction will first dissolve and then precipitate before dissolving again.When the water content is less than 0.0005 kg or greater than 0.4 kg,it will lead to an increase in reservoir porosity,which ultimately reduces the long-term geological storage stability of CO_(2)-rich IWG.展开更多
Asphaltene deposition is a significant problem during gas injection processes,as it can block the porous medium,the wellbore,and the involved facilities,significantly impacting reservoir productivity and ultimate oil re...Asphaltene deposition is a significant problem during gas injection processes,as it can block the porous medium,the wellbore,and the involved facilities,significantly impacting reservoir productivity and ultimate oil recovery.Only a few studies have investigated the numerical modeling of this potential effect in porous media.This study focuses on asphaltene deposition due to natural gas and CO_(2) injection.Predictions of the effect of gas injection on asphaltene deposition behavior have been made using a 3D numerical simulation model.The results indicate that the injection of natural gas exacerbates asphaltene deposition,leading to a significant reduction in permeability near the injection well and throughout the reservoir.This reduction in permeability strongly affects the ability of gas toflow through the reservoir,resulting in an improvement of the displacement front.The displacement effi-ciency of the injection gas process increases by up to 1.40%when gas is injected at 5500 psi,compared to the scenario where the asphaltene model is not considered.CO_(2) injection leads to a miscible process with crude oil,extracting light and intermediate components,which intensifies asphaltene precipitation and increases the viscosity of the remaining crude oil,ultimately reducing the recovery rate.展开更多
基金support from Sichuan Science and Technology Program(2021YFH0116)National Natural Science Foundation of China(No.52170112)DongFang Boiler Co.,Ltd.(3522015).
文摘Mixed matrix membranes(MMMs)could combine the advantages of both polymeric membranes and porousfillers,making them an effective alternative to conventional polymer membranes.However,interfacial incompatibility issues,such as the presence of interfacial voids,hardening of polymer chains,and blockage of micropores by polymers between common MMMsfillers and the polymer matrix,currently limit the gas sep-aration performance of MMMs.Ternary phase MMMs(consisting of afiller,an additive,and a matrix)made by adding a third compound,usually functionalized additives,can overcome the structural problems of binary phase MMMs and positively impact membrane separation performance.This review introduces the structure and fabrication processes for ternary MMMs,categorizes various nanofillers and the third component,and summarizes and analyzes in detail the CO_(2) separation performance of newly developed ternary MMMs based on both rubbery and glassy polymers.Based on this separation data,the challenges of ternary MMMs are also discussed.Finally,future directions for ternary MMMs are proposed.
文摘氮化硅是一种良好的载体,具有较高的水热稳定性和机械稳定性,其表面的氨基基团能够较好地锚定金属,显著提高金属分散度。但是,商品氮化硅比表面积较低,对金属分散作用仍然有限。因此,以自制的高比表面积氮化硅(Si_(3)N_(4))为载体,通过浸渍法制备了不同Ru负载量(质量分数分别为0.5%、1.0%和2.0%)的催化剂(分别为0.5%Ru/Si_(3)N_(4)、1.0%Ru/Si_(3)N_(4)和2.0%Ru/Si_(3)N_(4)),并以商品氮化硅(Si_(3)N_(4)-C)为载体制备了2.0%Ru/Si_(3)N_(4)-C催化剂作为对照组。表征了催化剂的理化性质,测试了其在300℃、0.1 MPa下的CO_(2)加氢反应活性。结果显示,与Si_(3)N_(4)-C相比,Si_(3)N_(4)的比表面积较高(502 m^(2)/g),Si_(3)N_(4)作为载体显著提高了金属分散度,降低了金属粒径,催化剂暴露出更多的活性位点。0.5%Ru/Si_(3)N_(4)的金属粒径较小,展现出强的H_(2)吸附能力,H难以解吸,抑制了中间物种CO加氢生成CH_(4)。随着Ru负载量增加,金属粒径增大,催化剂的CH_(4)选择性更好。Ru/Si_(3)N_(4)系列催化剂中,2.0%Ru/Si_(3)N_(4)的CH_(4)选择性较高(98.8%)。空速为10000 m L/(g·h)时,0.5%Ru/Si_(3)N_(4)的CO选择性为88.2%。与2.0%Ru/Si_(3)N_(4)相比,2.0%Ru/Si_(3)N_(4)-C的金属粒径更大,活性位点较少,活性更低。2.0%Ru/Si_(3)N_(4)和2.0%Ru/Si_(3)N_(4)-C的CO_(2)转化率分别为53.1%和9.2%。Si_(3)N_(4)有效提高了金属分散度,提高了催化剂的CO_(2)加氢反应活性;通过调控Ru负载量控制催化剂金属粒径,可实现对产物CO或CH_(4)选择性的调控。
基金The work was supported by the National Natural Science Foundation of China(No.52074316)PetroChina Company Limited(No.2019E-2608).
文摘"Carbon peaking and carbon neutrality"is an essential national strategy,and the geological storage and utilization of CO_(2)is a hot issue today.However,due to the scarcity of pure CO_(2)gas sources in China and the high cost of CO_(2)capture,CO_(2)-rich industrial waste gas(CO_(2)-rich IWG)is gradually emerging into the public's gaze.CO_(2)has good adsorption properties on shale surfaces,but acidic gases can react with shale,so the mechanism of the CO_(2)-rich IWG-water-shale reaction and the change in reservoir properties will determine the stability of geological storage.Therefore,based on the mineral composition of the Longmaxi Formation shale,this study constructs a thermodynamic equilibrium model of water-rock reactions and simulates the regularity of reactions between CO_(2)-rich IWG and shale minerals.The results indicate that CO_(2)consumed 12%after reaction,and impurity gases in the CO_(2)-rich IWG can be dissolved entirely,thus demonstrating the feasibility of treating IWG through water-rock reactions.Since IWG inhibits the dissolution of CO_(2),the optimal composition of CO_(2)-rich IWG is 95%CO_(2)and 5%IWG when CO_(2)geological storage is the main goal.In contrast,when the main goal is the geological storage of total CO_(2)-rich IWG or impurity gas,the optimal CO_(2)-rich IWG composition is 50%CO_(2)and 50%IWG.In the CO_(2)-rich IWG-water-shale reaction,temperature has less influence on the water-rock reaction,while pressure is the most important parameter.SO2 has the greatest impact on water-rock reaction in gas.For minerals,clay minerals such as illite and montmorillonite had a significant effect on water-rock reaction.The overall reaction is dominated by precipitation and the volume of the rock skeleton has increased by 0.74 cm3,resulting in a decrease in shale porosity,which enhances the stability of CO_(2)geological storage to some extent.During the reaction between CO_(2)-rich IWG-water-shale at simulated temperatures and pressures,precipitation is the main reaction,and shale porosity decreases.However,as the reservoir water content increases,the reaction will first dissolve and then precipitate before dissolving again.When the water content is less than 0.0005 kg or greater than 0.4 kg,it will lead to an increase in reservoir porosity,which ultimately reduces the long-term geological storage stability of CO_(2)-rich IWG.
基金funded by CNOOC Production Research Project(CCL2022SZPS0076).
文摘Asphaltene deposition is a significant problem during gas injection processes,as it can block the porous medium,the wellbore,and the involved facilities,significantly impacting reservoir productivity and ultimate oil recovery.Only a few studies have investigated the numerical modeling of this potential effect in porous media.This study focuses on asphaltene deposition due to natural gas and CO_(2) injection.Predictions of the effect of gas injection on asphaltene deposition behavior have been made using a 3D numerical simulation model.The results indicate that the injection of natural gas exacerbates asphaltene deposition,leading to a significant reduction in permeability near the injection well and throughout the reservoir.This reduction in permeability strongly affects the ability of gas toflow through the reservoir,resulting in an improvement of the displacement front.The displacement effi-ciency of the injection gas process increases by up to 1.40%when gas is injected at 5500 psi,compared to the scenario where the asphaltene model is not considered.CO_(2) injection leads to a miscible process with crude oil,extracting light and intermediate components,which intensifies asphaltene precipitation and increases the viscosity of the remaining crude oil,ultimately reducing the recovery rate.
