The ablation debris and raised rim, as well as residual stress and deep crater will be formed during the mitigation of damage site with a CO2 laser irradiation on fused silica surface, which greatly affects the laser ...The ablation debris and raised rim, as well as residual stress and deep crater will be formed during the mitigation of damage site with a CO2 laser irradiation on fused silica surface, which greatly affects the laser damage resistance of optics. In this study, the experimental study combined with numerical simulation is utilized to investigate the effect of the secondary treatment on a mitigated site by CO2laser irradiation. The results indicate that the ablation debris and the raised rim can be completely eliminated and the depth of crater can be reduced. Notable results show that the residual stress of the mitigation site after treatment will reduce two-thirds of the original stress. Finally, the elimination and the controlling mechanism of secondary treatment on the debris and raised rim, as well as the reasons for changing the profile and stress are analyzed. The results can provide a reference for the optimization treatment of mitigation sites by CO2laser secondary treatment.展开更多
In this paper a new kind of mid - infrared fiber material is reported. The reflective coefficients (R) of glasses in the system Na2O - ZnO - GeO2-SiO2-PbO have been measured-the refractive index becomes less than unit...In this paper a new kind of mid - infrared fiber material is reported. The reflective coefficients (R) of glasses in the system Na2O - ZnO - GeO2-SiO2-PbO have been measured-the refractive index becomes less than unity at 1180 - 900cm-1 range because of the existence of anomalous dispersion. The optical losses of hollow waveguides were calculated,the predicted losses at 940cm-1are 0. 65 and 0. 081B/ m as the inner diameter of fiber is 0. 5 and 1. 0mm respectively. The glasses can be used as the cladding materials of hol-low waveguides for transmitting CO2 laser from the measurements of characteristic temperatures, coefficient of expansion and chemical durability.展开更多
An accurate method of determining gain coefficients of pulse RF-discharge CO2 laser is developed, which involves the use of both the regular 00o1 and 00o2 laser transitions as probes of CO2 laser. The results indicate...An accurate method of determining gain coefficients of pulse RF-discharge CO2 laser is developed, which involves the use of both the regular 00o1 and 00o2 laser transitions as probes of CO2 laser. The results indicate that the majority of transitions in discharge have anomalous gain coefficients under RF-discharge condition. This fact has not been generally recognized and the neglect of overlapping transitions can lead to errors in determining rotational temperature.展开更多
High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of r...High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of renewable Fraxinus mandshurica was conducted by waterjet-assisted CO_(2)laser(WACL)technology.A quadratic mathematical model for describing the relationship between surface roughness changes and cutting parameters was established.The effects of cutting speed,flow pressure and laser power on the kerf surface roughness of Fraxinus mandshurica when cutting transversally were discussed by response surface method.The experimental results showed that kerf surface roughness decreased under a lower laser power,higher cutting speed and higher flow pressure.When the cutting speed was 30 mm/s,flow pressure was 1.58 MPa and laser power was 45 W,the actual surface roughness of the optimized Fraxinus mandshurica was 2.41μm,and it was in accord with the theoretically predicted surface roughness value of 2.54μm,so the model fitted the actual situation well.Through the analysis of 3D profile morphology and micromorphology,it was concluded that the optimized kerf surface of Fraxinus mandshurica was smoother,the cell wall was not destroyed and the tracheid was clear.It provides the theoretical basis for wood micromachining.展开更多
The performance of engineered wood products is highly associated with proper bonding and an efficient cutting method.This paper investigates the influence of CO_(2) laser cutting on the wetting properties,the modified ch...The performance of engineered wood products is highly associated with proper bonding and an efficient cutting method.This paper investigates the influence of CO_(2) laser cutting on the wetting properties,the modified che-mical component of the laser-cut surface,and the strength and adhesive penetration near the bondline.Beech-wood is cut by the laser with varying processing parameters,cutting speeds,gas pressures,and focal point positions.The laser-cut samples were divided into two groups,sanded and non-sanded samples.Polyvinyl acetate adhesive(PVAc)was used to bond the groups of laser-cut samples.After assembly with cold pressing,the tensile shear test was carried out.Numerical modelling was carried out to determine the partial elongation and shear strain of the glue line.Based on this,the shear modulus and linear elasticity of the glue line were estimated.Scan-ning electron microscopy was used to assess the adhesive penetration into the porosity structure of the laser-cut samples,and the depth of the heat-affected zone.The laser-cut surface was analysed by Fourier transform infrared spectroscopy.The wetting properties of the laser-cut surface were investigated by using a contact angle goni-ometer.The numerical model of the strain-stress curve confirmed the experimental model.The highest modulus of the linear elasticity of the glue in the numerical calculation belongs to the joint containing laser-cut samples at a gas pressure of 21(bar).The penetration depth of PVAc adhesive into the porosity structure of the laser-cut sam-ples was similar to that of sawn samples.The deepest heat-affected zone in the laser-cut samples was 150µm.A PVAc drop disappeared immediately on the laser-cut surface without sanding,but gradually on the sanded surface.In contrast,the drop on the sawn surface remained with an angle of 32°–48°.The degradation of hemi-cellulose and lignin was proven by the lower intensity of the C=O and C-O Bonds,compared to the sawn surface.展开更多
Time-integrated optical emission analysis of laser-induced plasma on Teflon is presented.Plasma was induced under atmospheric pressure air using transversely excited atmospheric CO_(2) laser pulses.Teflon is a C-based...Time-integrated optical emission analysis of laser-induced plasma on Teflon is presented.Plasma was induced under atmospheric pressure air using transversely excited atmospheric CO_(2) laser pulses.Teflon is a C-based polymer that is,among other things,interesting as a substrate for laser-induced breakdown spectroscopy analysis of liquid samples.This study aimed to determine the optimal experimental conditions for obtaining neutral and ionized C spectral lines and C2 and CN molecular band emission suitable for spectrochemical purposes.Evaluation of plasma parameters was done using several spectroscopic techniques.Stark profiles of appropriate C ionic lines were used to determine electron number density.The ratio of the integral intensity of ionic-to-atomic C spectral lines was used to determine the ionization temperature.A spectral emission of C2 Swan and CN violet bands system was used to determine the temperature of the colder,peripheral parts of plasma.We critically analyzed the use of molecular emission bands as a tool for plasma diagnostics and suggested methods for possible improvements.展开更多
目的:探究重组贻贝粘蛋白水凝胶敷料(Recombined mussel adhesive protein hydrogel dressing,Rmaphd)在点阵CO_(2)激光治疗面部痤疮萎缩性瘢痕术后创面修复中的应用效果。方法:选择2022年6月-2023年2月面部痤疮萎缩性瘢痕患者117例,分...目的:探究重组贻贝粘蛋白水凝胶敷料(Recombined mussel adhesive protein hydrogel dressing,Rmaphd)在点阵CO_(2)激光治疗面部痤疮萎缩性瘢痕术后创面修复中的应用效果。方法:选择2022年6月-2023年2月面部痤疮萎缩性瘢痕患者117例,分为Rmaphd组、重组人表皮生长因子(Recombinant human epidermal growth factor,rhEGF)组和对照组,每组39例,三组均给予点阵CO_(2)激光术治疗,术后分别给予Rmaphd、rhEGF及生理盐水处理,比较三组疗效、ECCA评分、症状持续时间以及生活质量评分。结果:Rmaphd组和rhEGF组总有效率分别为92.31%和94.87%,均高于对照组76.92%(P<0.05),术后ECCA评分低于对照组(P<0.05),术后疼痛、红斑、痂皮持续时间短于对照组(P<0.05),Acne-QoL各指标得分优于对照组(P<0.05);上述各临床Rmaphd组与rhEGF组差异无统计学意义(P>0.05)。结论:Rmaphd用于点阵CO_(2)激光治疗面部痤疮萎缩性瘢痕术后创面修复疗效显著,具备在临床上辅助激光治疗术后修复的应用潜力。展开更多
目的:探究点阵CO_(2)激光联合米诺地尔治疗雄激素性脱发(Androgenetic alopecia,AGA)的疗效及安全性分析。方法:选取2020年1月-2021年12月笔者医院收治的114例雄激素性脱发患者,采用单双球法随机分为对照组(n=57)和观察组(n=57),对照组...目的:探究点阵CO_(2)激光联合米诺地尔治疗雄激素性脱发(Androgenetic alopecia,AGA)的疗效及安全性分析。方法:选取2020年1月-2021年12月笔者医院收治的114例雄激素性脱发患者,采用单双球法随机分为对照组(n=57)和观察组(n=57),对照组给予米诺地尔治疗,观察组给予点阵CO_(2)激光与米诺地尔联合治疗。比较治疗6个月后两组患者的临床症状改善情况,对比治疗前和治疗6个月后两组患者治疗效果、毛发镜评价、生活质量[流调中心抑郁表(The center for epidemiological studies depression scale,CES-D)、皮肤病生活质量指数(Dermatology life quality index,DLQI)],记录治疗期间不良反应发生情况。结果:治疗6个月后,观察组临床症状改善评分高于对照组(P<0.05);两组脱发评分、新生发评、毳毛比例、CES-D、DLQI评分均较治疗前降低,观察组低于对照组(P<0.05);两组毛发密度、毛囊密度均较治疗前增大,观察组大于对照组(P<0.05);两组患者不良反应差异无统计学意义(P>0.05)。结论:点阵CO_(2)激光联合米诺地尔可改善AGA患者瘙痒、出油、头屑、毛囊炎等症状及毛发镜指标,改善患者生活质量,且不增加不良反应发生率。展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.61505170,61505171,and 51535003)the Joint Fund of the National Natural Science Foundation of China+1 种基金the Chinese Academy of Engineering Physics(Grant No.U1530109)the China Postdoctoral Science Foundation(Grant No.2016M592709)
文摘The ablation debris and raised rim, as well as residual stress and deep crater will be formed during the mitigation of damage site with a CO2 laser irradiation on fused silica surface, which greatly affects the laser damage resistance of optics. In this study, the experimental study combined with numerical simulation is utilized to investigate the effect of the secondary treatment on a mitigated site by CO2laser irradiation. The results indicate that the ablation debris and the raised rim can be completely eliminated and the depth of crater can be reduced. Notable results show that the residual stress of the mitigation site after treatment will reduce two-thirds of the original stress. Finally, the elimination and the controlling mechanism of secondary treatment on the debris and raised rim, as well as the reasons for changing the profile and stress are analyzed. The results can provide a reference for the optimization treatment of mitigation sites by CO2laser secondary treatment.
文摘In this paper a new kind of mid - infrared fiber material is reported. The reflective coefficients (R) of glasses in the system Na2O - ZnO - GeO2-SiO2-PbO have been measured-the refractive index becomes less than unity at 1180 - 900cm-1 range because of the existence of anomalous dispersion. The optical losses of hollow waveguides were calculated,the predicted losses at 940cm-1are 0. 65 and 0. 081B/ m as the inner diameter of fiber is 0. 5 and 1. 0mm respectively. The glasses can be used as the cladding materials of hol-low waveguides for transmitting CO2 laser from the measurements of characteristic temperatures, coefficient of expansion and chemical durability.
文摘An accurate method of determining gain coefficients of pulse RF-discharge CO2 laser is developed, which involves the use of both the regular 00o1 and 00o2 laser transitions as probes of CO2 laser. The results indicate that the majority of transitions in discharge have anomalous gain coefficients under RF-discharge condition. This fact has not been generally recognized and the neglect of overlapping transitions can lead to errors in determining rotational temperature.
基金supported by the Joint Scientific and Technological Innovation Project of Hainan Province(2021CXLH0001)the Teaching Reform in Higher Education of Heilongjiang Province(SJGY20210135)+4 种基金the Key Subject of Education Planning in Heilongjiang Province(GJB1423352)the Guiding Innovation Fund Project of Northeast Petroleum University(2022YDL-06 and 2021YDL-13)Daqing City Guiding Science and Technology Project(zd-2021-41)the Scientific Research Start-Up Fund Project of Northeast Petroleum University(2021KQ09 and 2019KQ67)the National Key R&D Program of China(2017YFD0601004).
文摘High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of renewable Fraxinus mandshurica was conducted by waterjet-assisted CO_(2)laser(WACL)technology.A quadratic mathematical model for describing the relationship between surface roughness changes and cutting parameters was established.The effects of cutting speed,flow pressure and laser power on the kerf surface roughness of Fraxinus mandshurica when cutting transversally were discussed by response surface method.The experimental results showed that kerf surface roughness decreased under a lower laser power,higher cutting speed and higher flow pressure.When the cutting speed was 30 mm/s,flow pressure was 1.58 MPa and laser power was 45 W,the actual surface roughness of the optimized Fraxinus mandshurica was 2.41μm,and it was in accord with the theoretically predicted surface roughness value of 2.54μm,so the model fitted the actual situation well.Through the analysis of 3D profile morphology and micromorphology,it was concluded that the optimized kerf surface of Fraxinus mandshurica was smoother,the cell wall was not destroyed and the tracheid was clear.It provides the theoretical basis for wood micromachining.
文摘The performance of engineered wood products is highly associated with proper bonding and an efficient cutting method.This paper investigates the influence of CO_(2) laser cutting on the wetting properties,the modified che-mical component of the laser-cut surface,and the strength and adhesive penetration near the bondline.Beech-wood is cut by the laser with varying processing parameters,cutting speeds,gas pressures,and focal point positions.The laser-cut samples were divided into two groups,sanded and non-sanded samples.Polyvinyl acetate adhesive(PVAc)was used to bond the groups of laser-cut samples.After assembly with cold pressing,the tensile shear test was carried out.Numerical modelling was carried out to determine the partial elongation and shear strain of the glue line.Based on this,the shear modulus and linear elasticity of the glue line were estimated.Scan-ning electron microscopy was used to assess the adhesive penetration into the porosity structure of the laser-cut samples,and the depth of the heat-affected zone.The laser-cut surface was analysed by Fourier transform infrared spectroscopy.The wetting properties of the laser-cut surface were investigated by using a contact angle goni-ometer.The numerical model of the strain-stress curve confirmed the experimental model.The highest modulus of the linear elasticity of the glue in the numerical calculation belongs to the joint containing laser-cut samples at a gas pressure of 21(bar).The penetration depth of PVAc adhesive into the porosity structure of the laser-cut sam-ples was similar to that of sawn samples.The deepest heat-affected zone in the laser-cut samples was 150µm.A PVAc drop disappeared immediately on the laser-cut surface without sanding,but gradually on the sanded surface.In contrast,the drop on the sawn surface remained with an angle of 32°–48°.The degradation of hemi-cellulose and lignin was proven by the lower intensity of the C=O and C-O Bonds,compared to the sawn surface.
基金funded by the Ministry of Education,Science and Technological Development of the Republic of Serbia(Nos.451-03-68/2022-14/200017 and 451-03-68/2022-14/200146)the financial support of the State Committee on Science and Technology of the Republic of Belarusthe Belarusian Republican Foundation for Fundamental Research(No.F20SRBG-001)。
文摘Time-integrated optical emission analysis of laser-induced plasma on Teflon is presented.Plasma was induced under atmospheric pressure air using transversely excited atmospheric CO_(2) laser pulses.Teflon is a C-based polymer that is,among other things,interesting as a substrate for laser-induced breakdown spectroscopy analysis of liquid samples.This study aimed to determine the optimal experimental conditions for obtaining neutral and ionized C spectral lines and C2 and CN molecular band emission suitable for spectrochemical purposes.Evaluation of plasma parameters was done using several spectroscopic techniques.Stark profiles of appropriate C ionic lines were used to determine electron number density.The ratio of the integral intensity of ionic-to-atomic C spectral lines was used to determine the ionization temperature.A spectral emission of C2 Swan and CN violet bands system was used to determine the temperature of the colder,peripheral parts of plasma.We critically analyzed the use of molecular emission bands as a tool for plasma diagnostics and suggested methods for possible improvements.
文摘目的:探究重组贻贝粘蛋白水凝胶敷料(Recombined mussel adhesive protein hydrogel dressing,Rmaphd)在点阵CO_(2)激光治疗面部痤疮萎缩性瘢痕术后创面修复中的应用效果。方法:选择2022年6月-2023年2月面部痤疮萎缩性瘢痕患者117例,分为Rmaphd组、重组人表皮生长因子(Recombinant human epidermal growth factor,rhEGF)组和对照组,每组39例,三组均给予点阵CO_(2)激光术治疗,术后分别给予Rmaphd、rhEGF及生理盐水处理,比较三组疗效、ECCA评分、症状持续时间以及生活质量评分。结果:Rmaphd组和rhEGF组总有效率分别为92.31%和94.87%,均高于对照组76.92%(P<0.05),术后ECCA评分低于对照组(P<0.05),术后疼痛、红斑、痂皮持续时间短于对照组(P<0.05),Acne-QoL各指标得分优于对照组(P<0.05);上述各临床Rmaphd组与rhEGF组差异无统计学意义(P>0.05)。结论:Rmaphd用于点阵CO_(2)激光治疗面部痤疮萎缩性瘢痕术后创面修复疗效显著,具备在临床上辅助激光治疗术后修复的应用潜力。
文摘目的:探究点阵CO_(2)激光联合米诺地尔治疗雄激素性脱发(Androgenetic alopecia,AGA)的疗效及安全性分析。方法:选取2020年1月-2021年12月笔者医院收治的114例雄激素性脱发患者,采用单双球法随机分为对照组(n=57)和观察组(n=57),对照组给予米诺地尔治疗,观察组给予点阵CO_(2)激光与米诺地尔联合治疗。比较治疗6个月后两组患者的临床症状改善情况,对比治疗前和治疗6个月后两组患者治疗效果、毛发镜评价、生活质量[流调中心抑郁表(The center for epidemiological studies depression scale,CES-D)、皮肤病生活质量指数(Dermatology life quality index,DLQI)],记录治疗期间不良反应发生情况。结果:治疗6个月后,观察组临床症状改善评分高于对照组(P<0.05);两组脱发评分、新生发评、毳毛比例、CES-D、DLQI评分均较治疗前降低,观察组低于对照组(P<0.05);两组毛发密度、毛囊密度均较治疗前增大,观察组大于对照组(P<0.05);两组患者不良反应差异无统计学意义(P>0.05)。结论:点阵CO_(2)激光联合米诺地尔可改善AGA患者瘙痒、出油、头屑、毛囊炎等症状及毛发镜指标,改善患者生活质量,且不增加不良反应发生率。
