The Al_(2)O_(3)and Mn/Al_(2)O_(3)sorbents highly utilized in destructive sorption of NF_(3)

NF_(3)is commonly used as an etching and cleaning gas in semiconductor industry,however it is a strongly greenhouse gas.Therefore,the destruction of disposal NF_(3)is an urgent task to migrate the greenhouse effect.Among the technologies for NF_(3)abatement,the destructive sorption of NF_(3)over metal oxides sorbents is an effective way.Thus,the search for a highly reactive and utilized sorbent for NF_(3)destruction is in great demand.In this work,AlOOH supported on carbon-sphere(AlOOH/CS)as precursors were synthesized hydrothermally and heat-treated to prepare the Al_(2)O_(3)sorbents.The influence of AlOOH/CS hydrothermal temperatures on the reactivity of derived Al_(2)O_(3)sorbents for NF_(3)destruction was investigated,and it is shown that the Al2O3 from AlOOH/CS hydro-thermalized at 120℃is superior to others.Subsequently,the optimized Al_(2)O_(3)was covered by Mn(OH)x to prepare Mn/Al_(2)O_(3)sorbents via changing hydrothermal temperatures and Mn loadings.The results show that the Mn/Al_(2)O_(3)sorbents are more utilized than bare Al_(2)O_(3)in NF_(3)destructive sorption due to the promotional effect of Mn_(2)O_(3)as surface layer on the fluorination of Al_(2)O_(3)as substrate,especially the optimal 5%Mn/Al2O3(160℃)exhibits a utilization percentage as high as 90.4%,and remarkably exceeds all the sorbents reported so far.These findings are beneficial to develop more efficient sorbents for the destruction of NF_(3).

Synthesis of highly reactive sorbent from industrial wastes and its CO_2 capture capacity

A kind of industrial solid waste, i.e., carbide slag, was used as CaO precursor to synthesize CO2 sorbent. The highly reactive synthetic sorbent was prepared from carbide slag, aluminum nitrate hydrate and glycerol water solution by the combustion synthesis method. The results show that the synthetic sorbent exhibits a much higher CO2 capture capacity compared with carbide slag. The CO2 capture capacity and the carbonation conversion of the synthetic sorbent are 0. 38 g/g and 0. 70 after 50 cycles, which are 1.8 and 2. 1 times those of carbide slag. The average carbonation conversion and the CO2 capture efficiency of the synthetic sorbent are higher than those of carbide slag with the same sorbent flow ratios. The required sorbent flow ratios are lower for synthetic sorbent to achieve the same CO2 capture efficiency compared with carbide slag. With the same sorbent flow ratio and CO2 capture efficiency, the energy requirement in calciner for the synthetic sorbent is less than that for carbide slag.

Impact of impregnation pressure on desulfurization performance of Zn-based sorbents supported on semi-coke

High-pressure impregnation, a new preparation method for sorbents to remove H2S from hot coal gas, is introduced in this paper. Semi-coke （SC） and ZnO is selected as the support and active component of sorbent, respectively. The sorbent preparation process includes high-pressure impregnation, filtration, ovendry and calcination. The aim of this research is to primarily study the effects of the impregnation pressure on physical properties and desulfurization ability of the sorbent. The desulfurization experiment was carried out in a fixed-bed reactor at 500 ~C and a simulated coal gas used in this work was composed of CO （33 vol%）, H2 （39 vol%）, H2S （300 ppm in volume）, and N2 （balance）. Experimental results show that the pore structure of the SC support can be improved effectively and ZnO active component can be uniformly dispersed on the support, with the small particle size of 10-500 nm. Sorbents prepared using high-pressure impregnation have better desulfurization capacity and their active components have higher utilization rate. P20-ZnSC sorbent, obtained by high-pressure impregnation at 20 atm, has the best desulfurization ability with a sulfur capacity of 7.54 g S/100g sorbent and a breakthrough time of 44 h. Its desulfurization precision and efficiency of removing H2S from the middle temperature gases can reach 〈 1 ppm and 〉99.7%, respectively, before sorbent breakthrough.

Recent progress of amine modified sorbents for capturing CO2 from flue gas

Under the Paris agreement, China has committed to reducing CO_2 emissions by 60%–65% per unit of GDP by 2030.Since CO_2 emissions from coal-fired power plants currently account for over 30% of the total carbon emissions in China, it will be necessary to mitigate at least some of these emissions to achieve this goal. Studies by the International Energy Agency(IEA) indicate CCS technology has the potential to contribute 14% of global emission reductions, followed by 40% of higher energy efficiency and 35% of renewable energy, which is considered as the most promising technology to significantly reduce carbon emissions for current coal-fired power plants.Moreover, the announcement of a Chinese national carbon trading market in late 2017 signals an opportunity for the commercial deployment of CO_2 capture technologies.Currently, the only commercially demonstrated technology for post-combustion CO_2 capture technology from power plants is solvent-based absorption. While commercially viable, the costs of deploying this technology are high. This has motivated efforts to develop more affordable alternatives, including advanced solvents, membranes,and sorbent capture systems. Of these approaches, advanced solvents have received the most attention in terms of research and demonstration. In contrast, sorbent capture technology has less attention, despite its potential for much lower energy consumption due to the absence of water in the sorbent. This paper reviews recent progress in the development of sorbent materials modified by amine functionalities with an emphasis on material characterization methods and the effects of operating conditions on performance. The main problems and challenges that need to be overcome to improve the competitiveness of sorbent-based capture technologies are discussed.

Effects of Sorbents on the Partitioning and Speciation of Cu During Municipal Solid Waste Incineration

Oxides of silicon, aluminium and calcium are normally dominant minerals during municipal solid waste(MSW)combustion. In flue gas, Si O2, Al2O3 and Ca O all act as sorbents capturing heavy metals(and semi-volatile organics). To further understand the effect of sorbents during MSW combustion, the effects of Si O2, Al2O3 and Ca O on Cu partitioning were experimentally investigated by the combustion of synthetic MSW in a tubular furnace and their effects on Cu speciation were studied by thermodynamic equilibrium calculations using Chem Kin software. The experiments show that Ca O has the highest Cu sorption efficiency at 900 °C, followed by Al2O3 and Si O2. Thermodynamic equilibrium calculations show that for Cu the addition of Si O2 and Al2O3reduces the amount of liquid Cu Cl, which is more volatile. However, the addition of Ca O has little influence on chemical sorption of Cu, indicating that the sorption of Ca O is resulted from physical sorption.

Preparation and utilization of wheat straw anionic sorbent for the removal of nitrate from aqueous solution

In order to reduce the impact of eutrophication caused by agricultural residues （i.e., excess nitrate） in aqueous solution, economic and effective anionic sorbents are required. In this article, we prepared anionic sorbent using wheat straw. Its structural characteristics and adsorption properties for nitrate removal from aqueous solution were investigated. The results indicate that the yield of the prepared anionic sorbent, the total exchange capacity, and the maximum adsorption capacity were 350%, 2.57 mEq/g, and 2.08 mmol/g, respectively. The Freundlich isotherm mode is more suitable than the Langmuir mode and the adsorption process accords with the first order reaction kinetic rate equation. When multiple anions （SO4^2-, H2PO4^-, NO3^-, and NO2^-） were present, the isotherm mode of prepared anionic sorbent for nitrate was consistent with Freundlich mode; however, the capacity of nitrate adsorption was reduced by 50%. In alkaline solutions, about 90% of adsorbed nitrate ions could be desorbed from prepared anionic sorbent. The results of this study confirmed that the wheat straw anionic sorbent can be used as an excellent nitrate sorbent that removes nitrate from aqueous solutions.

Desulfurization kinetics of ZnO sorbent loaded on semi-coke support for hot coal gas

Zn-based sorbent （Z20SC） prepared through semi-coke support in 20 wt% zinc nitrate solution by high-pressure impregnation presents an excellent desulfurization capacity in hot coal gas,in which H2 S can not be nearly detected in the outlet gas before 20 h breakthrough time.The effects of the main operational conditions and the particle size of Z20SC sorbent on its desulfurization performances sorbent were investigated in a fixed-bed reactor and the desulfurization kinetics of Z20SC sorbent removing H2 S from hot coal gas was calculated based on experimental data.Results showed that the conversion of Z20SC sorbent desulfurization reaction increased with the decrease of the particle size of the sorbent and the increases of gas volumetric flow rate,reaction temperature and H 2 S content in inlet gas.Z20SC sorbent obtained from hydrothermal synthesis by high-pressure impregnation possessed much larger surface area and pore volume than semi-coke support,and they were significantly reduced after the desulfurization reaction.The equivalent grain model was reasonably used to analyze experimental data,in which k s=4.382×10-3 exp（-8.270×103/RgT） and Dep=1.262×10-4exp（1.522×104/RgT）.It suggests that the desulfurization reaction of the Z20SC sorbent is mainly controlled by the chemical reaction in the initial stage and later by the diffusion through the reacted sorbent layer.

Bench-Scale Testing of Zinc Ferrite Sorbent for Hot Gas Clean-up

Advanced integrated gasification combined cycle （IGCC） power generation systems require the development of high-temperature, regenerable desulfurization sorbents, which are capable of removing hydrogen sulfide from coal gasifier gas to very low levels. In this paper, zinc ferrites prepared by co-precipitation were identified as a novel coal gas desulfurization sorbent at high temperature. Preparation of zinc ferrite and effects of binders on pore volume, strength and desulfurization efficiency of zinc ferrite desulfurizer were studied. Moreover, the behavior of zinc ferrite sorbent during desulfurization and regeneration under the temperature range of 350-400 ℃ are investigated. Effects of binders on the pore volume, mechanical strength and desulfurization efficiency of zinc ferrite sorbents indicated that the addition of kaolinite to zinc ferrite desulfurizer seems to be superior to other binders under the experimental conditions.

Effect of impregnation methods on sorbents made from lignite for desulfurization at middle temperature

With lignite after vacuum drying as the raw material,a series of Zn-based sorbents were prepared by static impregnation,ultrasonic-assisted impregnation,bubbling-assisted impregnation and high-pressure impregnation.The physical properties and the desulfurization performances of Zn-based sorbents were studied systematically by XRD,BET,AAS characterization techniques and the fixed-bed desulfurization evaluation apparatus.The sorbents obtained by high-pressure impregnation method have a larger specific surface area,pore volume and pore diameter comparing with other methods,which is conducive to the sulfidation reaction of hydrogen sulfide gas in the sorbent.The effects of pressure during the high-pressure impregnation and concentration of Zn(NO3)2 precursor solution on the sorbents properties and desulfurization behavior were investigated.The higher the impregnation pressure and the concentration of impregnation solution are,the greater the amount of the active components are uploaded.However,overhigh impregnation pressure can cause collapse and blocking of the carrier pore.The optimal operating condition of high-pressure impregnation method for preparing the sorbents was the impregnation pressure of 20 atm and the solution concentration of 41%.Under that condition,the sorbent had the best desulfurization ability with a sulfur capacity of 13.94 gS/100 gsorbent and a breakthrough time of 54 h.Its desulfurization precision and efficiency of removing H2S before sorbent breakthrough from the middle temperature gases of 400℃ can reach【5 ppm and】99%,respectively.Sorbents could be regenerated under the condition of 1 vol%O2,20 vol% H2O,0.5 vol% NH3,and N2balance gas.The regenerated sorbent could be used for repeated absorption of H2S with a slight decrease in desulfurization effect.

Study on Zn_2SiO_4 Formation Kinetics and Activity Stability of Desulfurization Sorbent

A new industrial S Zorb sorbent(Ni/Zn O-P) was prepared by using the spray drying technique. The other two traditional sorbents(Ni/Zn O-M and Ni/Zn O-H) were prepared in exactly the same way except the use of different silica-alumina binder matrices. The XRD, Rietveld quantitative phase analysis, BET, and laser particle size analysis were employed to characterize their physico-chemical properties. The deactivation mechanism and desulfurization kinetics of sorbent was investigated on a water vapor aging treatment device. It was shown that both the water vapor pressure and reaction temperature significantly could influence the formation rate of inactive Zn2 Si O4, which could decrease the sulfur storage capacity of sorbents. The Zn2 Si O4 content profiles could be fitted into the zero order equation, from which the apparent rate constant k and the activation energy E a were calculated. The matrix P greatly raised the E a of Zn2 Si O4 formation due to the less bridged hydroxyl silanol groups on its surface, which accounted for the high stability of Ni/Zn O-P. The desulfurization performance of the fresh and aged sorbents showed that the overall average sulfur conversion of Ni/Zn O-P(aged) was 92%, which was close to that of fresh sorbents(95%), and was higher than that of Ni/Zn O-M(aged)(86%) and Ni/Zn O-H(aged)(90%). Based on these findings, the application of Ni/Zn O-P can greatly improve the long-term running stability of the industrial unit.

Effects of ultrasound on the desulfurization performance of hot coal gas over Zn-Mn-Cu supported on semi-coke sorbent prepared by high-pressure impregnation method

Zn-Mn-Cu/SC（U） sorbent was hydrothermally synthesized by ultrasound-assisted high-pressure impregnation method with semi-coke（SC）as support and the mixed solution of zinc nitrate,manganese nitrate and copper nitrate as active component precursors.The desulfurization performances of hot coal gas on the prepared sorbent at a mid-temperature of 500°C were tested in fixed-bed reactor.Morphology and pore structure of the prepared sorbent were also characterized by TEM,N2adsorption/desorption isotherms and XRD.For comparison,the sorbent of Zn-Mn-Cu/SC prepared by conventional high-pressure impregnation was also evaluated and characterized in order to study the effects of ultrasound treatment.Zn-Mn-Cu/SC（U） sorbent prepared by high-pressure impregnation under ultrasound-assisted condition showed a better desulfurization performance than Zn-Mn-Cu/SC.It could remove H2 S from 1000×10-6m3/m3 to 0.1×10-6m3/m3 at 500°C and maintained for 12.5 h with the sulfur capacity of 7.74%,in which both the breakthrough time and sulfur capacity were about 32% and 51% higher than those of Zn-Mn-Cu/SC sorbent.The introduction of ultrasound during high-pressure impregnation process greatly improved the morphology and pore structure of the sorbent.The ultrasonic treatment made particle size of active components smaller and made them more evenly disperse on semi-coke support,which provided more opportunities to contact with H2S in coal-based gases.However,there were no any difference in compositions and existing forms of active components on the Zn-Mn-Cu/SC and Zn-Mn-Cu/SC（U） sorbents.

CO2 capture over molecular basket sorbents:Effects of SiO2 supports and PEG additive

The objective of this work is to study the influences of silica supports and PEG additive on the sorption performance of molecular basket sorbent（MBS） for COcapture consisting of polyethylenimine and one of the following supports: SBA-15（2-D structure）, TUD-1（3-D sponge-like structure） and fumed silica HS-5（3-D disordered structure）. Effects of the supports regarding pore structures and pore properties, the PEI loading amount as well as the sorption temperature were examined. Furthermore, polyethylene glycol（PEG） was introduced as an additive into the sorbents and its effect was investigated at different PEI loadings and sorption temperatures. The results suggest that the pore properties of MBS（after PEI loading） play a more important role in the COsorption capacity, rather than those of the supports alone.MBS with 3D pore structure exhibits higher COsorption capacity and amine efficiency than those with 2D-structured support. Among the sorbents studied, fumed silica（HS-5） based MBS showed the highest COsorption capacity in the temperature range of 30-95 °C, probably due to its unique interstitial pores formed by the aggregation of polymer-loaded SiOparticles. It was found that the temperature dependence is directly related to the PEI surface coverage layers. The more PEI surface coverage layers, the higher diffusion barrier for COand the stronger temperature dependence of COcapacity. 3D MBS exceeds 2D MBS at the same PEI coverage layers due to lower diffusion barrier. Adding PEG can significantly enhance the COsorption capacity and improve amine efficiency of all MBS, most likely by alleviating the diffusion barrier within PEI bulk layers through the inter-molecular interaction between PEI and PEG.

A fibrous hypercrosslinked sorbent prepared on PP-ST-DVB matrix via post-crosslinking reaction

A fibrous sorbent possessing abundant micropore structure was firstly prepared via post-crosslinking reaction on the PP-ST-DVB original fiber. Its micromorphology and sorptive properties were investigated, and the results demonstrated that the novel fibrous hypererosslinked sorbent has narrow pore-size distribution, small average porous radius （1.90 nm）, high specific surface area （362.31 m^2/g）, and fine sorptive properties for small organic molecules.

Sb(Ⅴ) removal from copper electrorefining electrolyte: Comparative study by different sorbents

Removal of Sb（V） from copper electrolyte by different sorbents such as activated carbon, bentonite, kaolin, resin, zeolite and white sand was investigated. Adsorption capacity of Sb（V） removal from copper electrolyte was as follows： white sand 〈 anionic resin 〈 zeolite 〈 kaolin 〈 activated carbon 〈 bentonite. Bentonite was characterized using FTIR, XRF, XRD, SEM and BET methods. The results show specific surface area of 95 m2/g and particles size of 175 nm for bentonite. The optimum conditions for the maximum removal of Sb are contact time 10 min, 4 g bentonite and temperature of 40 ° C. The adsorption of Sb（V） on bentonite is followed by pseudo-second-order kinetic （R2=0.996 and k=9×10？5 g/（mg· min））. Thermodynamic results reveal that the adsorption of Sb（V） onto bentonite from copper electrolyte is endothermic and spontaneous process （ΔGΘ=？4806 kJ/（mol· K）. The adsorption data fit both the Freundlich and Langmuir isotherm models. Bentonite has the maximum adsorption capacity of 10000 mg/g for adsorption of Sb（V） in copper electrolyte. The adsorption of Zn, Co, Cu and Bi that present in the copper electrolyte is very low and insignificant.

Effect of Calcium Oxide Additive on the Performance of Iron Oxide Sorbent for High-Temperature Coal Gas Desulfurization

The effect of calcium oxide additive in iron oxide sorbent for hot gas desulfurization was investigated by XRD and TPR techniques.XRD characterization showed that CaO was highly dispersed after the calcination of sorbents.Calcium sulfate formed in the desulfurization was decomposed and regenerated to CaO by reacting with CO before the next sulfidation process.Calcium participated in every sulfidation/regeneration cycle and contributed to the enhancement of sulfur capacity.The TPR results showed that the reduction temperature of the sorbent increased with the increase of the content of calcium.Calcium played a role of retarding reduction.Therefore,the addition of calcium oxide additive will benefit the utilization of iron oxide sorbent in strongly reducing atmospheres.

A New Solid Sorbent System for Rapid Monitoring of Dehydrogenated Nicotine by Using Furfural-hydrochloric Acid

A new solid sorbent system is developed for the monitoring of dehydrogenated nicotine in the environment. The reagent system for the indicator tube consists of furfural-hydrochloric acid and phosphoric acid impregnated over a cellulose fibre （cotton） and a humectant calcium chloride. The reagent system has also been used for the preparation of reagent paper. After exposing the indicator tubes and test paper to dehydrogenated nicotine, for a constant time, the red-violet colour developed could be compared with those obtained from standards. Alternatively the coloured compound was extracted in water and the absorbance measured at 540 nm. The lower limit of detection is 0.03 μg/m^3 of nicotine for the reagent papers and indicator tubes. The lower limit of determination by spectrophotometric procedure is 0.001μg/m^3 of air. The preparation of indicator tubes, test papers and their applications for the detection and determination of nicotine in environmental tobacco smoke （ETS）, mainstream smoke （MS）, side stream smoke （SS） and biological samples is described in this paper.

Supported ionic liquid sorbents for CO_2 capture from simulated flue-gas

Supported ionic liquid(IL) sorbents for CO_2 capture were prepared by impregnating tetramethylammonium glycinate([N1111][Gly]) into four types of porous materials in this study. The CO_2 adsorption behavior was investigated in a thermogravimetric analyzer(TGA). Among them, poly(methyl methacrylate)(PMMA)-[N1111][Gly]exhibits the best CO_2 adsorption properties in terms of adsorption capacity and rate. The CO_2 adsorption capacity reaches up to 2.14 mmol·g-1 sorbent at 35 °C. The fast CO_2 adsorption rate of PMMA-[N1111][Gly] allows 60 min of adsorption equilibrium time at 35 °C and much shorter time of 4 min is achieved at 75 °C. Further, Avrami's fractional-order kinetic model was used and fitted well with the experiment data, which shows good consistency between experimental results and theoretical model. In addition, PMMA-[N1111][Gly] remained excellent durability in the continuous adsorption–desorption cycling test. Therefore, this stable PMMA-[N1111][Gly] sorbent has great potential to be used for fast CO_2 adsorption from flue-gas.

Sorption of Pyruvic Acid with Weakly Basic Polymer Sorbents

Uptakes of pyruvic acid for two types of commercially available weakly basic polymer sorbents, D301G and D301R, have been measured over a wide pH range and at various salinities of MgSO4. The results show that the overloading adsorption of pyruvic acid occurs on both weakly basic polymer sorbents, and the overloading models can predict the experimental data of uptake very well. The overloading value for D301G is larger than that for D301R. The adsorption isotherm of pyruvic acid for both polymeric sorbents is greatly affected by the solution pH and MgSO4 concentration in the aqueous phase, and a high recovery efficiency of pyruvic acid from aqueous solution can be obtained at the solution pH around 2.

Influence of Carbon Content on S Zorb Sorbent Activity

The reaction activity of S Zorb sorbents with different sulfur contents was investigated, and the structure and composition of carbon-containing sorbents were characterized by XRD, FT-IR and TG-MS in order to delve into the kind and morphology of carbon on the sorbent. Test results have revealed that coke could be deposited on the S Zorb sorbent during the operating process, and the coke content was an important factor influencing the reaction performance of the S Zorb sorbent. Retention of a definite amount of coke on the sorbent while securing the desulfurization activity of the S Zorb sorbent would be conducive to the reduction of octane loss of reaction product.

Treatment of tunnel wash waters-experiments with organic sorbent materials.PartⅠ:Removal of polycyclic aromatic hydrocarbons and nonpolar oil

Tunnel wash waters characterize all waters that run off after washing procedures of tunnels are performed.These waters represent a wide spectrum of organic and inorganic pollutants,such as polycyclic aromatic hydrocarbons(PAHs)and toxic metals.Removal of such contaminants from water runoff was investigated using laboratory tests after washing procedure was performed on two road tunnels in eastern Norway(Hanekleiv and Bragernes).Due to diverse character of both,treatment media and treated wash waters, the wh...