A NOVEL CONTROL STRATEGY FOR SINUSIODAL WAVE INVERTER WITH PI REGULATORS AND CAPACITOR CURRENT FEEDBACK

Objective For the inverters used in UPS, it is important to maintain the pure sinusoidal AC output voltage waveform over all loading conditions and transients. Methods A novel sinusoidal output voltage control strategy is pregented in this paper. The output voltage is controlled by introducing filtering eapacitor current feedback. Two simple PI regulators are used for the current and voltage control loops. Results With the new control strategy, the inverter achieves very low output voltage distortion, good output voltage regulation and strong perturbation rejection, fast dynamic response, and good performance under nonlinear loads. The THD under capacitance rectifying load is better than 0.2%, the output voltage regulation within 0 to full load is less than 0.1%. The resting time under load transient is within 200?μ s . Conclusion The merits of the new control strategy include rapid response and good steady state stiffness.

Design of a Switched Capacitor Negative Feedback Circuit for a Very Low Level DC Current Amplifier

To miniaturize a very low level dc current amplifier and to improve its output response speed, the switched capacitor negative feedback circuit (SCNF), instead of the conventionally used high-ohmage resistor, is presented in this paper. In our system, a switched capacitor filter (SCF) and an offset controller are also used to decrease vibrations and offset voltage at the output of the amplifier using SCNF. The theoretical output voltage of the very low level dc current amplifier using SCNF is obtained. The experimental results show that the unnecessary components of the amplifier’s output are much decreased, and that the response speed of the amplifier with both the SCNF and SCF is faster than that using high-ohmage resistor.

currentMKMJ25-22型自愈式脉冲电容器耐久性试验条件的验证及其重要意义

随着电力装备制造技术的不断提升,自愈式脉冲电容器作为一种关键的电子元器件,在多个领域的应用逐渐得到广泛推广。为了确保这些电容器在实际应用中的稳定性和可靠性,必须对其进行严格的耐久性试验。然而,目前主流的试验方法尚不能准确快速地反映MKMJ25–22型自愈式脉冲电容器的实际性能。针对MKMJ25–22型自愈式脉冲电容器的试验问题,文章对标行业试验标准,对试验设备的能力进行了理论分析,并在元件选取、充放电回路等方面对试验回路进行了优化设计。通过对1台MKMJ25–22型自愈式脉冲电容器进行2000次的耐久性试验,证明回路、设备、配件均能够满足MKMJ25–22型自愈式脉冲电容器的试验要求。

基于信号注入法的电容电流计算方法改进

随着电网容量和密度的增大,系统单相接地时电容电流越来越大,因此准确计算电网电容电流十分必要。该文针对传统信号注入法存在的集中电容模型等效准确性不足、系统自然谐振频率过低、谐振频率搜索时存在偏差且搜索时间过长等问题进行分析与改进。首先,分析传统信号注入法产生的误差,结合中压配电网的频率特性,提出改进的单端口等效模型。然后,人为串联电容,解决谐振频率过低导致的励磁支路分流问题。最后,基于相位比较提出谐振频率的二分搜索法,降低搜索次数。改进的信号注入法计算电网电容误差为9.77%,传统方法误差为27.62%;现场实测电流绝对误差值降低3.65 A,超标率降低40%。改进的信号注入法可以有效降低计算电网电容的误差。

Instantaneous Current Feedback Control Strategy on Buck Mode Inverter

Buck型逆变器的电感电流瞬时值反馈控制和电容电流瞬时值反馈控制存在本质区别。以差动正激直流斩波器型高频环节逆变器为例，采用理论推导方法，研究这两种电流控制逆变器的稳定性、输出外特性、短路能力、输出功率特性、带非线性负载能力及动态响应特性。研究结果表明，电感电流瞬时值反馈控制逆变器具有电感电流和输出功率受限、较强的过载和短路能力、较软的输出外特性、较弱的带非线性负载能力、较差的动态响应等特点；而电容电流瞬时值反馈控制逆变器具有电感电流和输出功率不受限、较弱的过载能力、无短路能力、硬的输出外特性、较强的带非线性负载能力、较好的动态响应等特点。研究成果为Buck型逆变器电流型控制策略的选择及其设计提供重要的理论依据。

A Design of the Elliptic Switched Current Filter

In conformity with a fifth order RLC elliptic filter circuit prototype, it is easy to conceive the corresponding RC active filter circuit. Simple and feasible method presented here can be used to contrive the equivalent switched capacitor filter circuit and switched current filter circuit. Consulting the technique data manual, we can expediently design a specific RLC filter. Therefore, it is of great convenience to design the switched current filter, which has the same performances. Such a kind of technology is useful in the domain of analogue sampled data signal processing.

Growth and passivation of aluminum etch tunnels at on-off controlling direct current in 6 wt.% HCI solution

Growth and passivation of tunnels within Al foil by on-off controlling DC etching in 6 wt.% HCI solution has been investigated. It was found that, in a given etchant solution at a special temperature, the longest tunnel length was only a function of the turn-on interval of DC. The potential of Al foil broke at on-off controlling DC by the result from anode polarization curves and potential-time （E-t） responding curves. When DC was switched on, the potential increased abruptly over pitting potential, leading to nucleation of pits at the surface and the growth of tunnels at special length. When DC was switched off, the potential decreased rapidly to a passive value, leading to stoppage of nucleation and death of tunnels. By this way, the longest tunnel length can be controlled and a non-piercing layer can be obtained. Hence, etching of Al foil at this current is beneficial for maintaining a good mechanical strength.

Reducing input/output current ripple for driving converter by multiple technology

To improve the vehicle dynamic performance and ultra-capacitor operating circumstance,this paper studied the multi-current-two-quadrant converter applied to drive high power DC motor in ultra-capacitor electric bus(UCEB).Compared with normal current-two-quadrant converter,the multi-current-two-quadrant converter can reduce the motor armature current ripple and the ultra-capacitor current ripple.Moreover,it improves power capabilities,reliability and fault tolerant capability of driving system.After analyzing the structure and working principle of the multi-current-two-quadrant converter,the expressions of armature current ripple and the quantitative relationships between the ultra-capacitor power loss and duty cycle were derived.The simulation and experimental results showed that the multi-current-two-quadrant converter has great advantages in reducing the armature current ripple and ultra-capacitor power loss,which can improve the vehicle performance and overall efficiency.

Design and Verification of a High Performance LED Driver with an Efficient Current Sensing Architecture

A high power buck-boost switch-mode LED driver delivering a constant 350 mA with a power efficient current sensing scheme is presented in this paper. The LED current is extracted by differentiating the output capacitor voltage and maintained by a feedback. The circuit has been fabricated in a standard 0.35 μm AMS CMOS process. Measurement results demonstrated a power-conversion efficiency over 90% with a line regulation of 8%/V for input voltage of 3.3 V and current output between 200 mA and 350 mA.

Effect of Switching Devices on Power Quality and Transient Voltage Suppression Using Capacitor Bank Model

The main purpose of the electrical power system is to transport and distribute energy generated by the central power plants in a safe and reliable manner to the customer premises. Most of the electrical equipment is exposed within the open which suggests they can be vulnerable to lightning strikes, road dwindling, windstorms, and a few engineering activities with the potential of causing different degrees of damage to the electrical equipment. One of the ways to guard the equipment is to deploy switching devices. However, the operations of most of these switching devices produce oscillatory transient in the electrical transmission and distribution systems which result in voltage, current, and frequency fluctuations in the load. This paper investigates the effect of switching devices on power quality and proposes a positive sequence voltage power transient suppression technique that can spontaneously improve the distorted voltage at the instant of capacitor switching using the capacitor line model as a case study. MATLAB/Simulink software was utilized for the analysis on an electrical network model with bus voltages of 69 kV/12.47 kV and 480 V. The results showed that, during switching operations, the positive sequence voltage power detector block produces ripple-free accurate results.

Electrical characteristics of MOS capacitor with HfTiON gate dielectric and HfTiSiON interlayer

The paper reports that Hfrio dielectric is deposited by reactive co-sputtering of Hf and Ti targets in an Ar/O2 ambience, followed by an annealing in different gas ambiences of N2, NO and NH3 at 600℃ for 2 min. Capacitancevoltage and gate-leakage properties are characterized and compared. The results indicate that the NO-annealed sample exhibits the lowest interface-state and dielectric-charge densities and best device reliability. This is attributed to the fact that nitridation can create strong Si≡N bonds to passivate dangling Si bonds and replace strained Si-O bonds, thus the sample forms a hardened dielectric/Si interface with high reliability.

A Very Low Level dc Current Amplifier Using SC Circuit: Effects of Parasitic Capacitances and Duty Ratio on Its Output

This paper describes a very low level dc current amplifier using switched capacitor (SC) circuit to miniaturize and improve its output response speed, instead of the conventionally used high-oh-mage resistor. A switched capacitor filter (SCF) and an offset controller are also used to decrease vibrations and offset voltage at the output of the amplifier. The simulation results show that the parasitic capacitances that are distributed to the input portion of the amplifier have some effect on offset voltage. From the experimental results, it is seen that the duty ratio of the clock cycle of SC circuit should be in the range from 0.05 to 0.70. It is suggested that the proposed very low level dc current amplifier using SC circuit is an effective way to obtain both a faster output response and its miniaturization.

一种两倍升压五电平开关电容逆变器

开关电容型逆变器具有使用单直流电源输入、电容电压自均衡、输出谐波含量低以及高电压增益的优势。本文提出一种新型五电平逆变器拓扑,该拓扑由1个直流电源、2个浮动电容、1个电感以及4对互补开关管构成;采用多载波层叠调制策略实现开关电容与输入电源的分时串并联运行;实现了2倍电压增益、五电平输出以及电容电压自均衡;通过增加电感抑制了开关电容充电时存在的脉冲电流,降低了开关管的电流应力。此外,逆变电路中没有单独二极管器件,使得该电路具有能量双向流动的能力,扩展了电路的应用范围。本文详细分析了电路的构成及工作过程,仿真及实验结果验证了所提出的逆变器具有可行性。

感应电能传输系统多并联拾取模块电流和输出功率均衡方法

大功率感应电能传输系统通常采用多并联拾取模块结构。然而,多并联拾取模块参数不一致,会导致各个拾取模块的电流和输出功率不均衡,从而降低系统效率,严重时会因模块过流而造成系统故障。为解决该问题,文中提出一种基于并联拾取模块补偿电容器的多并联拾取模块电流和输出功率均衡方法。首先,介绍了传统感应电能传输系统与所提出的感应电能传输系统拓扑的特性。然后,分别分析了互感、拾取线圈自感及内阻对电流分布和系统效率的影响。最后,通过4个并联拾取模块的感应电能传输系统实验平台验证了所提方法的有效性。实验结果表明,采用所提方法时多并联拾取模块的电流和输出功率基本一致,并且相比传统感应电能传输系统,系统效率最高提升了2.21%。

Interfacial and electrical characteristics of a HfO_2/n–InAlAs MOS-capacitor with different dielectric thicknesses

AHfO2/n–In Al As MOS-capacitor has the advantage of reducing the serious gate leakage current when it is adopted in In As/Al Sb HEMT instead of the conventional Schottky-gate. In this paper, three kinds of Hf O2/n–InAlAs MOS-capacitor samples with different Hf O2 thickness values of 6, 8, and 10 nm are fabricated and used to investigate the interfacial and electrical characteristics. As the thickness is increased, the equivalent dielectric constant ε ox of Hf O2 layer is enhanced and the In AlAsHfO2 interface trap density Ditis reduced, leading to an effective reduction of the leakage current. It is found that the Hf O2 thickness of 10 nm is a suitable value to satisfy the demands of most applications of a HfO2/n–InAlAs MOS-capacitor, with a sufficiently low leakage current compromised with the threshold voltage.

电容电压平衡的四电平有源中性点钳位逆变器的改进模型预测电流控制

多电平有源中点钳位(ANPC)逆变器具有功率器件电压应力小、电流谐波低和器件损耗可调控等优点,被广泛应用于工业驱动中。针对四电平ANPC(4L-ANPC)逆变器的控制与调制研究相对较少,现有的调制方案实现复杂,中点电压(NPV)控制难度较大。因此,该文针对三相4L-ANPC逆变器,提出一种改进的有限集模型预测电流控制(FS-MPCC)算法,避免了复杂的调制过程。首先,使用仅包含电流误差的代价函数对位于六边形顶点的6个大电压矢量进行寻优;其次,对参与第一步寻优的大矢量划分扇区,使用包含电流误差和电容电压误差的代价函数对最优大矢量所在扇区的所有电压矢量滚动寻优,得到目标电压矢量并作用于逆变器;最后,仿真和实验结果表明,与传统的FS-MPCC相比,所提方法在降低系统计算负担的同时,还具有较好的控制性能和电容电压平衡能力。

SIMULATION STUDY ON CAPACITOR DISCHARGE PERCUSION WELDING

Based on the network theory, the discharge circuit model of capacitor discharge percussion welding machine is established. The discharge current waveform is calculated by means of simulation method. A thorough inquiry into the factors affecting the discharge current waveform is made by using orthogonal design method. Results show that the calculation results of the calculation program proposed well coincide with the actual experiment data.

基于电流应力优化和6脉波调制的双有源桥AC/DC变换器控制策略

针对双有源桥(dual active bridges,简称DAB)AC/DC变换器,该文提出基于电流应力优化和6脉波调制的双有源桥AC/DC变换器控制策略.DAB和三相逆变器(three phase inverter,简称TPI)是双有源桥AC/DC变换器的两个关键单元.对DAB采用电流应力优化,对TPI采用6脉波调制.仿真实验结果表明:相对于单移相(single phase shift,简称SPS)调制策略,该文策略的电感电流的峰值更小,即能更有效地降低电流应力.因此,该文所提策略具有优越性.

一种带飞跨电容的单相光伏逆变器

非隔离型逆变器存在的漏电流会增大系统损耗、产生安全隐患。研究了一种带飞跨电容的新型单相光伏逆变器,由5个开关管、一个飞跨电容和一个滤波器构成,结构简单,易于实现。逆变器交流侧与直流侧共地,可完全消除漏电流。针对该新型单相光伏逆变器,采用一种改进的单极性SPWM技术进行控制,优化了各开关管的控制逻辑,所有开关管只在半周期内高频调制,有利于减少开关管损耗。搭建了逆变器的仿真模型和实验样机,仿真和实验结果验证了理论分析的正确性。