A Unifi ed View of Carbon Neutrality:Solar-Driven Selective Upcycling of Waste Plastics

With the rapid development of plastic production and consumption globally,the amount of post-consumer plastic waste has reached levels that have posed environmental threats.Considering the substantial CO_(2)emissions throughout the plastic lifecycle from material production to its disposal,photocatalysis is considered a promising strategy for eff ective plastic recycling and upcycling.It can upgrade plastics into value-added products under mild conditions using solar energy,realizing zero carbon emissions.In this paper,we explain the basics of photocatalytic plastic reformation and underscores plastic feedstock reformation pathways into high-value-added products,including both degradation into CO_(2)followed by reformation and direct reformation into high-value-added products.Finally,the current applications of transforming plastic waste into fuels,chemicals,and carbon materials and the outlook on upcycling plastic waste by photocatalysis are presented,facilitating the realization of carbon neutrality and zero plastic waste.

Influence of Low-velocity Impact on Damage Behavior of Carbon Fiber-reinforced Composites

A combination of experimental measurements and numerical analysis was utilized to study the low-velocity impact damage of domestic carbon fiber-reinforced composites(CFRCs).The results indicated that the low-velocity impact damage induced pits and longitudinal cracks on the front side,oblique cracks and delaminationin on the back side.The pit depth increased with the increasing impact energy.It was demonstrated that the numerical analysis strain history curve was similar to the experimentally measured strain history curve,which verified the accuracy of numerical analysis in which the Hashin failure criterion was used.The work provides basic data and theoretical basis for the promotion and application of the domestic carbon fiber,and demonstrates the feasibility of replacing imported carbon fibers with domestic carbon fibers.

Can soil organic carbon sequestration and the carbon management index be improved by changing the film mulching methods in the semiarid region?

Plastic film mulching has been widely used to increase maize yield in the semiarid area of China.However, whether long-term plastic film mulching is conducive to agricultural sustainability in this region remains controversial.A field experiment was initiated in 2013 with five different film mulching methods:(i) control method, flat planting without mulching (CK),(ii) flat planting with half film mulching (P),(iii) film mulching on ridges and planting in narrow furrows(S),(iv) full film mulching on double ridges (D), and (v) film mulching on ridges and planting in wide furrows (R).The effects on soil organic carbon (SOC) content, storage, and fractions, and on the carbon management index (CMI)were evaluated after nine consecutive years of plastic film mulching.The results showed that long-term plastic film mulching generally maintained the initial SOC level.Compared with no mulching, plastic film mulching increased the average crop yield, biomass yield, and root biomass by 48.38, 35.06, and 37.32%, respectively, which led to the improvement of SOC sequestration.Specifically, plastic film mulching significantly improved CMI, and increased the SOC content by 13.59%, SOC storage by 7.47%and easily oxidizable organic carbon (EOC) by 13.78%on average,but it reduced the other labile fractions.SOC sequestration and CMI were improved by refining the plastic film mulching methods.The S treatment had the best effect among the four mulching methods, so it can be used as a reasonable film mulching method for sustainable agricultural development in the semiarid area.

Synthesis of Activated Carbon from Polyethylene Terephthalate(PET)Plastic Waste and Its Application for Removal of Organic Dyes from Water

Synthetic plastics are often considered to be materials that cannot be broken down by natural processes.One such plastic,polyethylene terephthalate(PET),is commonly used in everyday items but when these products are discarded,they can cause serious harm to the environment and human health.In this study,PET plastic waste was used to create activated carbon using a physical activation process that involved using CO2 gas.The researchers investigated the effects of different temperatures,carbonization,and activation times on the resulting activated carbon’s surface area.The activated carbon was then analyzed using scanning electron microscopy(SEM),X-ray diffraction(XRD),FTIR,and BET.The activated carbon created from PET plastic waste showed excellent absorption properties for methylene blue in aqueous solutions across a wide range of pH levels.By creating activated carbon from plastic waste,not only are environmental issues addressed,but high-value activated carbon is produced for environmental remediation purposes.

Carbon Fiber Breakage Mechanism in Aluminum(Al)/Carbon Fibers(CFs) Composite Sheet during Accumulative Roll Bonding(ARB) Process

We put forward a method of fabricating Aluminum(Al)/carbon fibers(CFs) composite sheets by the accumulative roll bonding(ARB) method. The finished Al/CFs composite sheet has CFs and pure Al sheets as sandwich and surface layers. After cross-section observation of the Al/CFs composite sheet, we found that the CFs discretely distributed within the sandwich layer. Besides, the tensile test showed that the contribution of the sandwich CFs layer to tensile strength was less than 11% compared with annealed pure Al sheet. With ex-situ observation of the CFs breakage evolution with-16%,-32%, and-45% rolling reduction during the ARB process, the plastic instability of the Al layer was found to bring shear damages to the CFs. At last, the bridging strengthening mechanism introduced by CFs was sacrificed. We provide new insight into and instruction on Al/CFs composite sheet preparation method and processing parameters.

Entrance and Exit Defects During Coarse Pitch Orbital Drilling of Carbon Fiber Reinforced Plastic Plates

Formation of entrance and exit defects in coarse pitch orbital drilling(CPOD)of carbon fiber reinforced plastic(CFRP)plates was investigated.Deep observation on entrance and exit morphology shows tear and burr are typical defects.Meanwhile,tear is more obvious than burr,and more entrance tears emerge than exit tears.As one of the major causes of entrance and exit defects in CPOD,cutting forces were substaintially studied by contrast experiments.Then,the effect of cutting parameters on entrance and exit tear was qualitatively analyzed through a single factor test.Experiment results indicate that the variation of rotation speed has little influence on entrance and exit tear.Increasing tangential feed per tooth can enlarge entrance tear,but bring little effect on exit tear.By increasing axial feed pitch,the hole entrance and exit show severe tear.When revolution radius grows bigger and bigger,entrance and exit tear firstly decreases,and then increases.Finally,the models of tear and delamination during CPOD of CFRP were established,the formation mechanisms of entrance and exit defects were revealed,and the control strategies were accordingly put forward.

Response of carbon footprint to plastic film mulch application in spring maize production and mitigation strategy

Producing more food with a lower environmental cost is one of the most crucial challenges worldwide. Plastic mulching has developed as one of the most dominant practices to improve crop yields, however its impacts on greenhouse gas(GHG) emissions during the production life cycle of a crop are still unclear. The objective of this work is to quantify the impacts of plastic film on GHG emissions and to reduce GHG emissions with innovative agronomic practices. Carbon footprint per unit of area(CFa), per unit of maize grain yield(CFy), and per unit of economic output(CFe) were evaluated for three maize cultivation systems: a no mulch system, a conventional plastic mulching system(PM) and a biennial plastic mulching pattern, namely a ’one film for 2 years’ system(PM2), during 2015–2018 in a maize field located on the Loess Plateau of China. The results suggested that PM induced a 24% improvement in maize yields during the four experimental years compared to a no-mulch treatment(NM). However, PM dramatically increased the CFa by 69%, 59% of which was created by the input of the plastic film material, and 10% was created by increases in the soil N2O emissions. The yield improvements from PM could not offset the increases in CFa, and CFy and CFe were both increased by 36%. Shifting from PM to PM2 did not reduce crop yields, but it led to a 21% reduction in CFa and 23% reductions in CFy and CFe due to the reduced input amount of plastic film, decreased soil N2O emissions, and less diesel oil used for tillage. Compared to NM, CFy and CFe were only 5% higher in PM2. This study highlights the necessity of reducing the amount of plastic film input in the development of low-carbon agriculture and shifting from conventional PM cultivation to PM2 could be an efficient option for mitigating GHG emissions while sustaining high crop yields in plastic mulched fields.

Critical Thrust Force Forecasting for Drilling Exit Delamination of Carbon Fibre Reinforced Plastics

Exit delamination is excessive drilling thrust force.Therefore,it is necessary to investigate the critical thrust force which cause exit delamination when carbon fibre reinforced plastics(CRFP)is drilled.According to the linear elastic fracture mechanics,the mechanics of composite material and the classical thin plate bending theory,a common theoretical model of the critical drilling thrust force for CFRP plates is established.Compared with the experimental data of previous studies,the results show that the theoretical values agree well with the experimental values.This model can be used to forecast the critical thrust force for the drilling-induced delamination of CFRP.

Microstructure of Carbon Fiber and Carbon Reinforced Plastic

This study is the investigation of the microstructure of different types of carbon fiber. They were compared with the carbonized and graphitized fibers. Results of structural researches have been presented. It was found that the damage varies from different pollution and the damage of the monofibers. The effect of the pollution of the monofiber was determined.

Feasibility study of wave-motion milling of carbon fiber reinforced plastic holes

Carbon fiber reinforced plastic(CFRP)has been applied in aeronautics,aerospace,automotive and medical industries due to its superior mechanical properties.However,due to its difficult-to-cut characteristic,various damages in twist drilling and chip removal clog in core drilling could happen,inevitably reducing hole quality and hole-manufacturing efficiency.This paper proposes the wave-motion milling(WMM)method for CFRP hole-manufacturing to improve hole quality.This paper presents a motion path model based on the kinematics of the WMM method.The wave-motion cutting mode in WMM was analyzed first.Then,comparison experiments on WMM and conventional helical milling(CHM)of CFRP were carried out under dry conditions.The results showed that the hole surface quality of the CFRP significantly improved with a decrease of 18.1%–36%of Ra value in WMM compared to CHM.WMM exerted a significantly weaker thrust force than that of CHM with a reduction of 12.0%–24.9%and 3%–7.7%for different axial feed per tooth and tangential feed per tooth,respectively.Meanwhile,the hole exit damages significantly decreased in WMM.The average tear length at the hole exit in WMM was reduced by 3.5%–29.5%and 35.5%–44.7%at different axial feed per tooth and tangential feed per tooth,respectively.Moreover,WMM significantly alleviated tool wear.The experimental results suggest that WMM is an effective and promising strategy for CFRP hole-manufacturing.

On the plastic buckling of curved carbon nanotubes

This research,for the first time,predicts theoretically static stability response of a curved carbon nanotube(CCNT)under an elastoplastic behavior with several boundary conditions.The CCNT is exposed to axial compressive loads.The equilibrium equations are extracted regarding the Euler–Bernoulli displacement field by means of the principle of minimizing total potential energy.The elastoplastic stress-strain is concerned with Ramberg–Osgood law on the basis of deformation and flow theories of plasticity.To seize the nano-mechanical behavior of the CCNT,the nonlocal strain gradient elasticity theory is taken into account.The obtained differential equations are solved using the Rayleigh–Ritz method based on a new admissible shape function which is able to analyze stability problems.To authorize the solution,some comparisons are illustrated which show a very good agreement with the published works.Conclusively,the best findings confirm that a plastic analysis is crucial in predicting the mechanical strength of CCNTs.

Square concrete columns strengthened with carbon fiber reinforced plastics sheets at low temperatures

Twenty-one square concrete columns were constructed and tested. The testing results indicate that bonded carbon fiber reinforced plastics(CFRP) sheets can be used to increase the strength and improve the serviceability of damaged concrete columns at low temperatures. The failure of the specimens,in most cases,takes place within the middle half of the columns. And the failure of strengthened columns is sudden and explosive. The CFRP sheets increase both the axial load capacity and the ultimate concrete compressive strain of the columns. The ultimate loads of strengthened columns at-10,0 and 10 ℃ increase averagely by 9.09%,6.63% and 17.83%,respectively,as compared with those of the control specimens. The axial compressive strength of strengthened columns is related to the curing temperatures. The improvement of axial compressive strength decreases with reducing temperature,and when the temperature drops to a certain value,the improvement increases with falling temperature.

Effect of Fibre Packing on Random Variability of Compressive Strength of Unidirectional Carbon Fibre Reinforced Plastic

Compression tests on twenty unidirectional(UD) carbon fibre reinforced plastic(CFRP) specimens are conducted, the statistics on the measured compressive strength is calculated, and the fracture surface is characterized. Two types of different fracture surface are experimentally observed, and they are corresponding to very different values on the compressive strength. A finite element(FE) analysis is conducted to investigate the influence of random fibre packing on the compressive strength. And a riks method(provided in ABAQUS software) is applied in FE model to analyze fibre buckling behaviour in the vicinity of compressive failure. The FE analysis agrees well with the experimental observation on the two types of buckling modes and also the partition of compressive strength. It is clearly shown that the random fibre packing lays a significant influence on the random variability of compressive strength of CFRP.

Experimental Investigation on Hydrophobic Behavior of Carbon Spheres Coated Surface Made from Microplastics

In this paper,a simple method to plate a hydrophobic coating on the inner surface of a small-scaled tube was proposed,where the coating consisted of carbon microspheres.Three common plastics polystyrene,polycarbonate and polyethylene were used as the feedstocks to be processed in supercritical water in a quartz tubular reactor.After reaction,the contact angle of droplet on the inner surface of the quartz tube was turned out to be over 100°,significantly larger than that of the blank tube 54°.When processing polystyrene in the 750℃ supercritical water for 10 min,the largest contact angle was obtained,up to 145°.Besides,in this sample,the size of carbon spheres was smallest,about 2.09μm diameter on average.When comparing among different types of plastics under the same condition,the contact angle of surface made from PC took the dominant position over that of PS and PE,124°,100°and 90°,respectively.In the sample made from PC,carbon spheres adhered into a mountainlike shape,producing a binary geometric structure.Furthermore,this research could be helpful in the discussion of plastic waste management and carbon spheres fabrication with low cost.

Tribological Behavior of Diamond Coatings against Carbon Fiber Reinforced Plastics under Dry Conditions

The frictional resistance and machining quality when cutting carbon fiber reinforced plastics (CFRP) laminates are associated with tribological behavior of tool materials. In the present study, the tribological properties of three types of monolayer microcrystalline diamond (MCD) coatings, nanocrystalline diamond (NCD) coatings and dual-layer MCD/NCD coatings sliding against CFRP are investigated under dry lubricated conditions using the rotational friction tester. The coefficients of friction (COF), wear rate and worn surfaces of the contacted surfaces are analyzed for the MCD-CFRP, NCD-CFRP and MCD/NCD-CFRP contacting pairs. The results show that compared with the monolayer MCD and NCD, the bilayer of MCD/NCD coating displays the lowest COF with the value of ~0.13, it is 42% and 55% of the values for MCD and NCD coatings. Due to the rough surfaces of MCD, the wear debris of CFRP on MCD samples exhibits the plowing effect. While for the NCD and MCD/NCD samples, the wear fragments display the planar shapes. The wear rate of CFRP against MCD is more than twice that of CFRP against NCD, due to the excellent loading capacity. While the wear rate of CFRP against MCD/NCD is about twice than that of CFRP-NCD pairs. The bilayer of MCD/NCD combines the excellent advantages of high hardness of MCD and the smooth surface of NCD. It shows the broad application potential for the bilayer coatings.

Adsorption of Indigo Carmine Dye by Composite Activated Carbons Prepared from Plastic Waste (PET) and Banana Pseudo Stem

This study is on the adsorption of indigo carmine dye by composite activated carbons prepared from banana pseudo stems and plastic waste. The activated carbons named TB1P1, TB1P1h and TB2P1 were obtained by pyrolysis at 700°C under steam of raw materials at different ratios (1:1 and 2:1). They were characterized by different techniques such as SEM/EDX, Raman Spectroscopy, FTIR, XRD, TGA/DTA and BET/BJH. Analyses indicate amorphous structures with specific surface areas of 424.37;385.45 and 338.84 m2/g for TB1P1, TB1P1h and TB2P1 respectively. The study of the adsorption of indigo carmine dye by these adsorbents was carried out by varying parameters such as contact time, mass of adsorbent and initial concentration of the dye. The maximum retention is 94.71%, 86.18% and 84.17% for TB1P1, TB1P1h and TB2P1 respectively after 60 min of stirring, for a pH = 4.6 using 0.6 g of adsorbents. The adsorption of indigo carmine follows well, the Langmuir model, with the most suitable kinetics as pseudo second order.

CHARACTERISTICS OF CATION—CONDUCTIVE BLENDS PLASTICIZED WITH PROPYLENE CARBONATE

The cation—conductive blends plasticized with propylene carbonate were prepared. The blends exhibited good mechanical strength and single—cation conduction over a wide range of plasticizer composition. The plasticizer not only increases the conductivity of the blends but also decreases the electrochemical interface resistance between the blend and lithium electrode. The carrier in the blends obviously grows in number.

3D Printing of Polylactic Acid Bioplastic–Carbon Fibres and Twisted Kevlar Composites Through Coextrusion Using Fused Deposition Modeling

Polylactic acid(PLA)bioplastic is a common material used in Fused Deposition Modeling(FDM)3D printing.It is biodegradable and environmentally friendly biopolymer which made out of corn.However,it exhibits weak mechanical properties which reduced its usability as a functional prototype in a real-world application.In the present study,two PLA composites are created through coextruded with 3K carbon fibres and twisted Kevlar string(as core fibre)to form a fibre reinforced parts(FRP).The mechanical strength of printed parts was examined using ASTM D638 standard with a strain rate of 1 mm/min.It has been demonstrated that the FRPs coextruded with 3K carbon fibres had achieved significant improvement in Young’s modulus(+180.6%,9.205 GPa),ultimate tensile strength(+175.3%,103 MPa)and maximum tensile strain(+21.6%,1.833%).Although the Young’s modulus of Kevlar FRP was found to be similar to as compared to unreinforced PLA(~3.29 GPa),it has gained significant increment in terms of maximum tensile strain(+179.7%,104.64 MPa),and maximum tensile strain(+257%,5.384%).Thus,this study revealed two unique composite materials,in which the 3K carbon FRP can offer stiff and high strength structure while Kevlar FRP offers similar strength but at a higher elasticity.

Effects of Plastic Film Mulching on Soil Carbon Fixation Capacity and Fertility Level in Eastern Qinghai

[Objectives]To explore the effects of single application of chemical fertilizers on soil carbon fixation capacity and soil fertility under plastic film mulching conditions in eastern Qinghai,and to provide a theoretical basis for realizing the sustainable development of film mulching planting method in this area.[Methods]The effects of single application of chemical fertilizer cultivation mode under film mulching conditions on the soil organic carbon(SOC),labile organic carbon(LOC),carbon management index(CMI),extractable humus carbon(CHE),humic acid carbon(CHA),and fulvic acid carbon(CFA)in the cultivated layer(0-20 cm)were studied through three consecutive years of field experiments on dryland maize farmland in the eastern Qinghai.[Results]Under the film mulching condition,the SOC,LOC and CMI of the single application of chemical fertilizer cultivation mode were lower than that of the open field control.CHE,CHA and CFA increased with the increase of planting years,but the degree of increase was generally less than that of the open field control.With the increase of planting years,by 2020,the soil LOC/SOC value of film mulching decreased by 4.97%compared with before the start of the experiment,while the open field control increased by 1.11%;the organic carbon oxidation stability coefficient(KOS)of the film mulching was higher than that of the open field control;the soil CHA/CFA value and PQ value were higher than that of the open field control.[Conclusions]Under the condition of single application of chemical fertilizers,the continuous film mulching cultivation mode reduces the soil carbon fixation capacity,and soil organic carbon tends to be stable,which is not conducive to biological utilization and could reduce the soil fertility and degrade the soil quality,causing adverse effects on the stability of crop yield and sustainable production in the long run.

Development of a Thermoplastic Magnesia Carbon Brick ——“A Cold Process Flexible System”

Conventional resin bonded MgO-C bricks, which are manufactured via cold mixing process, harden and attain brittleness during carbonization of resin due to the formation of isotropic glassy carbon. They do not exhibit thermo-plasticity, which can facilitate the release of huge amount of stresses generated during preheating or in operation. On the contrary, pitch bonded MgO-C bricks, show better pyro-plasticity due to formation of an anisotropic and graphitized coke structure during carbonization of pitch. Hence, pitch bonded bricks show a superior structural spalling resistance in comparison to resin-bonded bricks. One of the drawbacks of pitch-bonded bricks is that the manufacturing requires a hot mixing process and hot pressing facility. This paper describes how a combination of above two processes was optimized to make a MgO-C brick via cold process. These bricks exhibit a low Modulus of Elasticity and thereby facilitate release of stresses during operation. Normal coal tar pitch is considered as an environmental hazard due to the presence of polyaromatic hydrocarbons like benzopyrene B [ a ] P. So, a special binder with a low B[ a ] P was selected, which is eco-friendly in nature. Such bricks were made in our plant in China and supplied to an integrated steel plant in Europe for their ladle. The bricks supplied have given encouraging life.