CoS Nanosheets Coated with Dopamine-Derived Carbon Standing on Carbon Fiber Cloth as Binder-Free Anode for Li-ion Batteries

Cobalt sulphides attract much attention as anode materials for Li-ion batteries(LIBs).However,its poor conductivity,low initial column efficiency and large volume changes during cycling have hindered its further development.Herein,novel interlaced CoS nanosheets were firstly prepared on Carbon Fiber Cloth(CFC)by two hydrothermal reactions followed with carbon coating via carbonizing dopamine(CoS NS@C/CFC).As a freestanding anode,the nanosheet structure of CoS not only accommodates the volume variation,but also provides a large interface area to proceed the charge transfer reaction.In addition,CFC works as both a three-dimensional skeleton and an active substance which can further improve the areal capacity of the resulting electrode.Furthermore,the coated carbon combined with the CFC work as a 3D conductive network to facilitate the electron conduction.The obtained CoS NS@C/CFC,and the contrast sample prepared with the same procedure but without carbon coating(CoS NS/CFC),are characterized with XRD,SEM,TEM,XPS and electrochemical measurements.The results show that the CoS NS@C/CFC possesses much improved electrochemical performance due to the synergistic effect of nanosheet CoS,the coated carbon and the CFC substrate,exhibiting high initial columbic efficiency(~87%),high areal capacity(2.5 at 0.15 mA cm−2),excellent rate performance(1.6 at 2.73 mA cm−2)and improved cycle stability(87.5%capacity retention after 300 cycles).This work may provide a new route to explore freestanding anodes with high areal specific capacity for LIBs.

A review of the carbon coating of the silicon anode in highperformance lithium-ion batteries

In the development of rechargeable lithium ion batteries(LIBs),silicon anodes have attracted much attention because of their extremely high theoretical capacity,relatively low Li-insertion voltage and the availability of silicon resources.However,their large volume expansion and fragile solid electrolyte interface(SEI)film hinder their commercial application.To solve these problems,Si has been combined with various carbon materials to increase their structural stability and improve their interface properties.The use of different carbon materials,such as amorphous carbon and graphite,as three-dimensional(3D)protective anode coatings that help buffer mechanical strain and isolate the electrolyte is detailed,and novel methods for applying the coatings are outlined.However,carbon materials used as a protective layer still have some disadvantages,necessitating their modification.Recent developments have focused on modifying the protective carbon shells,and substitutes for the carbon have been suggested.

Protective Graphite Coating for Two-Dimensional Carbon/Carbon Composites

Two-dimensional carbon/carbon(2D C/C)composites are a special class of carbon/carbon composites,generally obtained by combining resin-impregnated carbon fiber clothes,which are then cured and carbonized.This study deals with the preparation of a protective coating for these materials.This coating,based on graphite,was prepared by the slurry method.The effect of graphite and phenolic resin powders with different weight ratios was examined.The results have shown that the coating slurry can fill the pores and cracks of the composite surface,thereby densifying the surface layer of the material.With the increase of the graphite powder/phenolic resin weight ratio,the coating density is enhanced while the coating surface flatness decreases;moreover,the protective ability of coating against erosion first increases(from 1:3 to 2:2)and then decreases(from 2:2 to 3:1).When the weight ratio is about 1:1,the coating for 2D C/C composites exhibits the best erosion resistance,which greatly aids these materials during gas quenching.In this case,the erosion rate is decreased by approximately 41.5%at the impact angle of 30°and 52.3%at normal impact,respectively.This can be attributed to the ability of the coating slurry to infiltrate into the substrate,thereby bonding the fibers together and increasing the compactness of the 2D C/C composites.

Long cycle-life aqueous Zn battery enabled by facile carbon nanotube coating on Cu current collector

As an alternative to Li-ion batteries,aqueous Zn batteries have gained attention due to the abundance of Zn metal,low reduction potential(-0.76 V vs.standard hydrogen electrode),and high theoretical capacity(820 mAh g^(-1))of multivalent Zn2+ion.However,the growth of Zn dendrites and the formation of irreversible surface reaction byproducts pose challenges for ensuring a long battery lifespan and commercialization.Herein,the Cu foil coated with a single-walled carbon nanotube(SWCNT)layer using a facile doctor blade casting method is utilized.The SWCNT-coated Cu foil demonstrates a significantly longer battery lifespan compared to the bare Cu in the half-cell tests.Through operando optical microscopy imaging,we are able to provide intuitive evidence that Zn deposition occurs between the carbon nanotube(CNT)coating and Cu substrate,in agreement with the computational results.Also,with various imaging techniques,the flat morphology and homogeneous distribution of Zn beneath the SWCNT layer are demonstrated.In addition,the full-cell using CNT-coated Cu exhibits a long cycle life compared to the control group,thereby demonstrating improved electrochemical performance with limited Zn for the cycling process.

Preparation and electrochemical lithium storage performance of porous silicon microsphere composite with metal modification and carbon coating

This work adopts a multi⁃step etching⁃heat treatment strategy to prepare porous silicon microsphere com⁃posite with Sb⁃Sn surface modification and carbon coating(pSi/Sb⁃Sn@C),using industrial grade SiAl alloy micro⁃spheres as a precursor.pSi/Sb⁃Sn@C had a 3D structure with bimetallic(Sb⁃Sn)modified porous silicon micro⁃spheres(pSi/Sb⁃Sn)as the core and carbon coating as the shell.Carbon shells can improve the electronic conductivi⁃ty and mechanical stability of porous silicon microspheres,which is beneficial for obtaining a stable solid electrolyte interface(SEI)film.The 3D porous core promotes the diffusion of lithium ions,increases the intercalation/delithia⁃tion active sites,and buffers the volume expansion during the intercalation process.The introduction of active met⁃als(Sb⁃Sn)can improve the conductivity of the composite and contribute to a certain amount of lithium storage ca⁃pacity.Due to its unique composition and microstructure,pSi/Sb⁃Sn@C showed a reversible capacity of 1247.4 mAh·g^(-1) after 300 charge/discharge cycles at a current density of 1.0 A·g^(-1),demonstrating excellent rate lithium storage performance and enhanced electrochemical cycling stability.

Influence of carbon sources on the performance of carbon-coated nano-silicon

Silicon-based material is an important anode material for next-generation lithium-ion batteries.In order to overcome its shortcomings,carbon coating is often employed to improve the electrochemical performance.However,the carbon source,carbon content,and different contact and mixing schemes between carbon sources and silicon are all complex factors and need to be clarified.In this study,nano-silicon is coated by the chemical vapor deposition method using different carbon sources,such as acetylene,methane,propane,and propylene.Carbon content after coating is designed to stay at the same level to reduce the experimental error.Results show the sample with higher conductivity provides higher cycle performance.Propylene is the best choice of the four carbon sources studied in this work.These results indicate that the selection of the carbon source is an important factor that plays a significant role in electrochemical performance.

Carbon-coated ZnO Nanocomposite Microspheres as Anode Materials for Lithium-ion Batteries

The carbon-coated ZnO nanospheres materials have been synthesized via a simple hydrothermal method.The effect of carbon content on the microstructure,morphology and electrochemical performance of the materials was investigated by XRD,Raman spectroscopy,transmission electron microscopy,scanning electron microscopy and electrochemical techniques.Research results show that the spherical ZnO/C material with a carbon cladding content of 10%is very homogeneous and approximately 200 nm in size.The electrochemical performances of the ZnO/C nanospheres as an anode materials are examines.The ZnO/C exhibits better stability than pure ZnO,excellent lithium storage properties as well as improved circulation performance.The Coulomb efficiency of the ZnO/C with 10%carbon coated content reaches 98%.The improvement of electrochemical performance can be attributed to the carbon layer on the ZnO surface.The large volume change of ZnO during the charge-discharge process can be effectively relieved.

Preparation and oxidation resistance of B_2O_3-coated boron-modified carbon foams

To improve the oxidation resistance of boron-modified carbon foams, the B2O3 coating was prepared on boron-modified carbon foams by low-cost slurry method. The microstructures and phase compositions of the coated carbon foams were characterized by scanning electron microscopy and X-ray diffraction, respectively. Oxidation resistances of uncoated and coated boron-modified carbon foams were investigated at 873 K in air. The results showed that as-received B2O3 coating could protect boron-modified carbon foams from oxidation at 873 K. B2O3-coated carbon foam doped with 7% B2O3 （mass fraction） （BO-7） had better oxidation resistance, exhibiting mass loss of 17.40% after oxidation at 873 K for 120 min. The melting glass layer formed on the surface of BO-7 could prevent oxygen from diffusing into boron-modified carbon foams substrate during oxidation to some extent.

VOLTAMMETRIC BEHAVIOR OF ASCORBIC ACID AT α-CYCLODEXTRIN INCORPORATED CARBON NANOTUBES-COATED ELECTRODE

制备了α -环糊精掺杂纳米碳管涂层电极并应用于抗坏血酸的电催化氧化 ,结果表明 ,氧化电位降低了 2 80mV ,电流响应明显增加。我们首次结合两种物质的特性 :纳米碳管的导电性及催化性能、α -环糊精的分子认知能力 ,对电极表面进行修饰。实验了抗坏血酸与α -环糊精超分子络合物的特性。差示脉冲技术用于定量分析抗坏血酸 ,线性范围为 2 .5× 10 -6～ 1.0× 10

Carbon-coated manganese dioxide nanoparticles and their enhanced electrochemical properties for zinc-ion battery applications

In this study, we report the cost-effective and simple synthesis of carbon-coated α-MnOnanoparticles(α-MnO@C) for use as cathodes of aqueous zinc-ion batteries(ZIBs) for the first time. α-MnO@C was prepared via a gel formation, using maleic acid(CHO) as the carbon source, followed by annealing at low temperature of 270 °C. A uniform carbon network among the α-MnOnanoparticles was observed by transmission electron microscopy. When tested in a zinc cell, the α-MnO@C exhibited a high initial discharge capacity of 272 m Ah/g under 66 m A/g current density compared to 213 m Ah/g, at the same current density, displayed by the pristine sample. Further, α-MnO@C demonstrated superior cycleability compared to the pristine samples. This study may pave the way for the utilizing carbon-coated MnOelectrodes for aqueous ZIB applications and thereby contribute to realizing high performance eco-friendly batteries.

Preparation and electrochemical properties of carbon-coated LiFePO_4 hollow nanofibers

Carbon-coated LiFePO_4 hollow nanofibers as cathode materials for Li-ion batteries were obtained by coaxial electrospinning. X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Brunauer–Emmett–Teller specific surface area analysis, galvanostatic charge–discharge, and electrochemical impedance spectroscopy（EIS） were employed to investigate the crystalline structure, morphology, and electrochemical performance of the as-prepared hollow nanofibers. The results indicate that the carbon-coated LiFePO_4 hollow nanofibers have good long-term cycling performance and good rate capability： at a current density of 0.2C（1.0C = 170 mA ·g^-1） in the voltage range of 2.5–4.2 V, the cathode materials achieve an initial discharge specific capacity of 153.16 mA h·g^-1 with a first charge–discharge coulombic efficiency of more than 97%, as well as a high capacity retention of 99% after 10 cycles; moreover, the materials can retain a specific capacity of 135.68 mA h·g^-1, even at 2C.

Effects of heat treatment on the corrosion resistance of carbon steel coated with LaMgAl_(11)O_(19) thermal barrier coatings

LaMgAl11O19thermal barrier coatings（TBCs） were applied to carbon steels with a NiCoCrAlY bond coat by plasma spraying. The effects of heat treatment on the corrosion resistance of carbon steel coated with LaMgAl11O19TBCs were investigated in 3.5wt% Na Cl solution using polarization curves, electrochemical impedance spectroscopy（EIS）, scanning electron microscopy（SEM）, and X-ray diffraction（XRD）. The results show that a large number of cracks are found in the LaMgAl11O19TBCs after the samples are heat-treated, including some through-thickness cracks. The corrosion forms of the as-sprayed and heat-treated TBCs are uniform corrosion and pitting corrosion, respectively. The as-sprayed TBCs exhibit three EIS time constants after being immersed for less than 7 d, and then a new time constant appears because of steel substrate corrosion. When the immersion time is increased to 56 d, a Warburg impedance（W） component appears in the EIS data. The EIS data for the heat-treated TBCs exhibit only two time constants after the samples are immersed for less than 14 d, and a new time constant appears when the immersion time is increased further. The heat treatment reduces the corrosion resistance of carbon steel coated with LaMgAl11O19TBCs. The corrosion products are primarily γ-Fe OOH and Fe3O4.

Electrochemical properties of carbon-coated LiFePO_4 and LiFe_(0.98)Mn_(0.02)PO_4 cathode materials synthesized by solid-state reaction

Olivine structured LiFePO 4 /C (lithium iron phosphate) and Mn 2+ -doped LiFe 0.98 Mn 0.02 PO 4 /C powders were synthesized by the solid-state reaction. The effects of manganese partial substitution and different carbon content coating on the surface of LiFePO 4 were considered. The structures and electrochemical properties of the samples were measured by X-ray diffraction (XRD), cyclic voltammetry (CV), charge/discharge tests at different current densities, and electrochemical impedance spectroscopy (EIS). The electrochemical properties of LiFePO 4 cathodes with x wt.% carbon coating (x= 3, 7, 11, 15) at =0.2C, 2C (1C= 170 mAh·g 1 ) between 2.5 and 4.3 V were investigated. The measured results mean that the LiFePO 4 with 7 wt.% carbon coating shows the best rate performance. The discharge capacity of LiFe 0.98 Mn 0.02 PO 4 /C composite is found to be 165 mAh·g 1 at a discharge rate, = 0.2C, and 105 mAh·g 1 at =2C, respectively. After 10 cycles, the discharge capacity has rarely fallen, while that of the pristine LiFePO 4 /C cathode is 150 mAh·g 1 and 98 mAh·g 1 at =0.2 and 2C, respectively. Compared to the discharge capacities of both electrodes above, the evident improvement of the electrochemical performance is observed, which is ascribed to the enhancement of the electronic conductivity and diffusion kinetics by carbon coating and Mn 2+-substitution.

Improved wettability and mechanical properties of metal coated carbon fiber-reinforced aluminum matrix composites by squeeze melt infiltration technique

In order to improve the wettability and bonding performance of the interface between carbon fiber and aluminum matrix,nickel-and copper-coated carbon fiber-reinforced aluminum matrix composites were fabricated by the squeeze melt infiltration technique.The interface wettability,microstructure and mechanical properties of the composites were compared and investigated.Compared with the uncoated fiber-reinforced aluminum matrix composite,the microstructure analysis indicated that the coatings significantly improved the wettability and effectively inhibited the interface reaction between carbon fiber and aluminum matrix during the process.Under the same processing condition,aluminum melt was easy to infiltrate into the copper-coated fiber bundles.Furthermore,the inhibited interface reaction was more conducive to maintain the original strength of fiber and improve the fiber−matrix interface bonding performance.The mechanical properties were evaluated by uniaxial tensile test.The yield strength,ultimate tensile strength and elastic modulus of the copper-coated carbon fiber-reinforced aluminum matrix composite were about 124 MPa,140 MPa and 82 GPa,respectively.In the case of nickel-coated carbon fiber-reinforced aluminum matrix composite,the yield strength,ultimate tensile strength and elastic modulus were about 60 MPa,70 MPa and 79 GPa,respectively.The excellent mechanical properties for copper-coated fiber-reinforced composites are attributed to better compactness of the matrix and better fiber−matrix interface bonding,which favor the load transfer ability from aluminam matrix to carbon fiber under the loading state,giving full play to the bearing role of carbon fiber.

Electrostatic Interaction-directed Construction of Hierarchical Nanostructured Carbon Composite with Dual Electrical Conductive Networks for Zinc-ion Hybrid Capacitors with Ultrastability

Metal-organic framework(MOF)-derived carbon composites have been considered as the promising materials for energy storage.However,the construction of MOF-based composites with highly controllable mode via the liquid-liquid synthesis method has a great challenge because of the simultaneous heterogeneous nucleation on substrates and the self-nucleation of individual MOF nanocrystals in the liquid phase.Herein,we report a bidirectional electrostatic generated self-assembly strategy to achieve the precisely controlled coatings of single-layer nanoscale MOFs on a range of substrates,including carbon nanotubes(CNTs),graphene oxide(GO),MXene,layered double hydroxides(LDHs),MOFs,and SiO_(2).The obtained MOF-based nanostructured carbon composite exhibits the hierarchical porosity(V_(meso)/V_(micro)∶2.4),ultrahigh N content of 12.4 at.%and"dual electrical conductive networks."The assembled aqueous zinc-ion hybrid capacitor(ZIC)with the prepared nanocarbon composite as a cathode shows a high specific capacitance of 236 F g^(-1)at 0.5 A g^(-1),great rate performance of 98 F g^(-1)at 100 A g^(-1),and especially,an ultralong cycling stability up to 230000 cycles with the capacitance retention of 90.1%.This work develops a repeatable and general method for the controlled construction of MOF coatings on various functional substrates and further fabricates carbon composites for ZICs with ultrastability.

Interfacial Interaction in Coated Carbon Fibre Reinforced Aluminous Mg-based Composites

Four kinds of Mg alloys reinforced with carbon fibres were fabricated by a gas pressure infiltration technique. The fibres were pre-coated a SiO2 layer prior to fabrication. DifFerent microstructures and interactions in the fibre-matrix interface of these composites were observed by transmission electron microscopy （TEM）. The results showed that the interracial interaction strongly depended on the content of Al in the Mg-based matrices. The microstructure of the interface could then be controlled by adjusting the Al content of the Mgbased matrix. In addition, fibres extracted from different Mg-based matrix all had some degradation owing to the interracial reaction and the fibre-matrix interdiffusion.

Influence of Thermal Shock on the Mechanical Behavior of Si-SiC Coated Carbon/Carbon Composites

Si-SiC coating was prepared on the surface of carbon/carbon （C/C） composites by a two-step technique of pack cementation, and the influences of thermal shock between 1773 K and room temperature in air on the mechanical property and fracture behavior of the coated C/C were studied. The results show that, after thermal shock between !773 K and room temperature for 5, 10 and 15 times, the flexural strength of coated composites increases by 4.29%, 15.00% and 24.20%, respectively. The toughness of the coated C/C enhances gradually during the thermal shock test. The improvement of the mechanical property after the thermal shock test is primarily caused by the weakening of the fiber-matrix interface and the reduction of residual thermal stresses by thermal shock.

Microstructural and Mechanical Characterization of SiBNC Coated Carbon Fibers Prepared via PIP Method

The preparation of SiBNC ceramic oxidation-resistant coating on carbon fiber via precursorsolution infiltration and pyrolysis（PIP） method was presented and discussed in detail. Moreover, the microstructures and the components of the coating were characterized. The experiment results showed that the 0.5% polyborosilazane（PBSZ） solution in the coating preparation gave fewer defects, in contrast with the 1% and the 5% PBSZ solutions. The strength of the carbon fiber coated with SiBNC-0.5 wt%（3.08 GPa） was decreased by 12%. Compared with uncoated carbon fiber, the starting oxidation temperature and the reaction activation energy of the coated carbon fibers（SiBNC-0.5 wt%） have increased by about 300 ℃ and 104%, respectively. The oxidation resistance of the SiBNC coated carbon fiber was improved dramatically.

Synthesis and characterization of carbon-coated cobalt ferrite nanoparticles

Cobalt ferrite nanoparticles（CFNPs） were prepared via a reverse micelle method. The CFNPs were subsequently coated with carbon shells by means of thermal chemical vapor deposition（TCVD）. In this process, acetylene gas（C2H2） was used as a carbon source and the coating was carried out for 1, 2, or 3 h at 750℃. The Ar/C2H2 ratio was 10：1. Heating during the TCVD process resulted in a NP core size that approached 30 nm; the thickness of the shell was less than 10 nm. The composition, structure, and morphology of the fabricated composites were characterized using X-ray diffraction, simultaneous thermal analysis, transmission electron microscopy, high-resolution transmission electron microscopy, and selected-area diffraction. A vibrating sample magnetometer was used to survey the samples＇ magnetic properties. The deposited carbon shell substantially affected the growth and magnetic properties of the CFNPs. Micro-Raman spectroscopy was used to study the carbon coating and revealed that the deposited carbon comprised graphite, multiwalled carbon nanotubes, and diamond-like carbon. With an increase in coating time, the intensity ratio between the amorphous and ordered peaks in the Raman spectra decreased, which indicated an increase in crystallite size.

Enhanced corrosion resistance of epoxy resin coating via addition of CeO_(2) and benzotriazole

The use of fillers to enhance the corrosion protection of epoxy resins has been widely applied.In this work,cerium dioxide(CeO_(2))and benzotriazole(BTA)were introduced into an epoxy resin to enhance the corrosion resistance of Q235 carbon steel.Scanning electron microscopy results indicated that the CeO_(2) grains were rod-like and ellipsoidal in shape,and the distribution pattern of BTA was analyzed by energy dispersive spectroscope.The dynamic potential polarization curve proved the excellent corrosion resistance of the composite epoxy resin with CeO_(2) and BTA co-addition,and electrochemical impedance spectroscopy test analysis indicated the significantly enhanced long-term corrosion protection performance of the composite coating.And the optimal protective performance was provided by the coating containing 0.3%(mass)CeO_(2) and 20%(mass)BTA,which was attributed to the barrier performance of CeO_(2) particles and the chemical barrier effect of BTA.The formation of corrosion products was analyzed using X-ray diffraction.In addition,the corrosion resistance mechanism of the coating was also discussed in detail.