Characterization and Methanol Adsorption of Walnutshell Activated Carbon Prepared by KOH Activation

Walnut-shellactivated carbons（WSACs）were prepared by the KOH chemicalactivation.The effects of carbonization temperature,activation temperature,and ratio of KOH to chars on the pore development of WSACs were investigated.Fourier transform infrared spectroscopy（FTIR）,X-ray powder diffraction（XRD）,and scanning electron microscopy（SEM）were employed to characterize the microstructure and morphology of WSACs.Methanoladsorption performance onto the optimalWSAC and the coal-based AC were also investigated.The results show that the optimalpreparation conditions are a carbonization temperature of 700 ℃,an activation temperature of 700 ℃,and a mass ratio of 3.The BET surface area,the micropore volume,and the micropore volume percentage of the optimalWASC are 1636 m^2/g,0.641 cm^3/g and 81.97%,respectively.There are a lot of micropores and a certain amount of meso-and macropores.The characteristics of the amorphous state are identified.The results show that the optimalWSAC is favorable for methanoladsorption.The equilibrium adsorption capacity of the optimalWSAC is 248.02mg/g.It is shown that the equilibrium adsorption capacity of the optimalWSAC is almost equivalent to that of the common activated carbon.Therefore the optimalWSAC could be a potentialadsorbent for the solar energy adsorption refrigeration cycle.

INVESTIGATIONS ON NANOMETER-SIZED ULTRAMICRO-ELECTRODES(Ⅱ)—FABRICATION, CHARACTERIZATION OF CARBON FIBER CYLINDER ULTRAMICROELECTRODES

Described here are the fabrication and characterization of carbon fiber cylinder ultramicroelectrodes with cylinder length of less than 100 am, total tip diameter of several hundreds nanometers. The electrodes have been fabricated by direct etching of carbon fiber using an ion beam thinner. Optical microscopy, scanning electron microscopy (SEM), cyclic voltammetry have been employed to characterize those electrodes. The experimental results obtained indicate the electrodes can be used for in vivo detection of neurotransmitters such as dopamine, 5—hydroxytryptamine in a single cell.

Preparation and Characterization of Ni-Ferrite Coating on Carbon Steel Coupons

The effect of the presence of Ni in solution as Ni-EDTA complex in lithiated water at roon temperature and pH 10.5 on the formation of ferrite coating on carbon steel surface was studie in an autoclave at 523 K for 12 days at different Ni concentrations with varying amounts of free EDTA. The Ni-ferrite coating was characterized by XRD, SIMS and XPS and also bulk chemical analysis by AAS and UV-visible spectrophotometer. The chemical composition of Ni-ferrite coating showed variation with depth acro5s solution-oxide interface to oxide-metal interface.The content of Ni in the oxide coating on the surface near solution-oxide intedece was found to be higher than the average Ni content estimated by analysis after descaling the coating

Assembly and electrochemical testing of renewable carbon-based anodes in SIBs:A practical guide

Sodium-ion batteries(SIBs)are considered as a promising candidate to replace lithium-ion batteries(LIBs)in large-scale energy storage applications.Abundant sodium resources and similar working principles make this technology attractive to be implemented in the near future.However,the development of high-performance carbon anodes is a focal point to the upcoming success of SIBs in terms of power density,cycling stability,and lifespan.Fundamental knowledge in electrochemical and physicochemical techniques is required to properly evaluate the anode performance and move it in the right direction.This review aims at providing a comprehensive guideline to help researchers from different backgrounds(e.g.,nanomaterials and thermochemistry)to delve into this topic.The main components,lab configurations,procedures,and working principles of SIBs are summarized.Moreover,a detailed description of the most used electrochemical and physicochemical techniques to characterize electrochemically active materials is provided.

Optical characterization of nano-sized organic carbon particles emitted from a small gasoline engine

The nano-sized organic carbon （NOC） particles emitted from a small gasoline engine were characterized using various ex situ optical techniques to assess their hazardous impact. The exhaust gas was sampled iso-kinetically by a quartz probe and passed through de-ionized water to gather the hydrophilic car- bonaceous particulates as hydrosol. The hydrodynamic diameter of the particles ranged between 1.7 and 3.6 nm at no load, with a mean diameter of 2.4 nm. The particle size in the engine exhaust was found to increase at higher loads, which is attributed to coagulation of the particles. The chemical structure of the particles was analyzed using UV-vis and infra-red spectroscopy. Both the band gap energy and oscillator strength data evaluated from the UV-vis absorbance showed that the NOC particles contained polyaromatic hydrocarbon structures with three to five aromatic rings. Infra-red spectroscopy analysis further confirmed the presence of aliphatic and carbonyl functionalities in the aromatic structures of the particles. The fine size of the particles, their high number concentration for the type of the engine under study and their structural features, make the particles extremely hazardous for environment and health.

Source apportionment of atmospheric particulate carbon in Las Vegas,Nevada,USA

A study was conducted to quantify wintertime contributions of source types to carbonaceous PM2.5 at four urban sites in the Las Vegas Valley, one of the most rapidly growing urban areas in the southwestern United States. Twenty-four hour average ambient samples were collected for mass, ions, elements, organic carbon （OC）, elemental carbon （EC）, and trace organic markers analysis. Additional measurements were made to determine diurnal patterns in light-absorbing black carbon （BC） as a marker for combustion sources. Carbonaceous PM sources of on-road gasoline vehicles, on-road diesel vehicles, and off-road diesel engines were characterized with their chemical profiles, as well as fuel-based emission factors, using an In-Plume Sampling System. The Effective Variance Chemical Mass Balance （EV-CMB） source apportionment model was applied to the ambient samples collected, using source profiles developed in this study as well as profiles from other relevant studies. Four main sources contributed to PM2.5 carbon within the Las Vegas Valley： （1） paved road dust, （2） on-road gasoline vehicles, （3） residential wood combustion, and （4） on-road diesel vehicles. CMB estimated that on-road mixed fleet gasoline vehicles are the largest source for OC and EC at all the sites. The contribution of paved road dust to both OC and EC was 5-10% at the four sites. On-road diesel vehicles contribute 22% of the OC and 34% of the EC at a site near the city center, which is located immediately downwind of a major freeway. Residential wood combustion is a more important source than on-road diesel vehicles for two residential neighborhood sites, These results are consistent with our conceptual model, and the research methodology may be applied to studying other urban areas.

Carbon nanotubes/TiO_2 nanotubes composite photocatalysts for efficient degradation of methyl orange dye

A series of carbon nanotubes/TiO2 nanotubes （CNTs/TNTs） composite photocatalysts were successfully prepared by incorporation of CNTs in HNO3 washing process. These photocatalysts were characterized by XRD, N2 physical adsorption, UV-vis diffuse reflectance spectroscopy, TEM and Raman spectroscopy, respectively, and their photocatalytic activities were tested by using methyl orange （MO） as a model compound. Also, the effects of amount of CNTs incorporated, calcination temperature and amount of catalyst on the photocatalytic activity of the composite photocatalyst were systematically investigated. The results show that the CNTs/TNTs composite exhibits much higher photocatalytic activity than that of the TNTs or CNTs alone.

The effect of oxidation on physicochemical properties and aqueous stabilization of multiwalled carbon nanotubes：comparison of multiple analysis methods

Surface oxidation can alter physicochemical properties of multiwalled carbon nanotubes(MWCNTs) and influence their aqueous stabilization.Many techniques have been used to characterize the physicochemical properties and aqueous stabilization of MWCNTs.However,the relationship between the change in physicochemical property and the aqueous stabilization of MWCNTs merits more studies,and the multiple characterization techniques have not been well compared.This study systematically and comparatively investigated the effect of oxidation on the physicochemical properties and aqueous stabilization of MWCNTs using multiple analysis methods.Increased surface area,disclosed tube ends,defects on the sidewalls,disruption of the electronic structure,and removal of metal catalysts and amorphous carbon were observed for the oxidized MWCNTs(o-MWCNTs) using the multipoint Brunauer-Emmett-Teller(BET) method,transmission electron microscope observation,Raman spectroscopy,UV-Vis spectroscopy,and thermogravimetric analysis.An oxidation-time-dependent increase in oxygen content of the MWCNTs was verified by the methods of elemental analysis,mass difference calculation,and X-ray photoelectron spectroscopy(XPS).Fourier transform infrared spectroscopy,XPS,and the Boehm titration were employed to study the functionalities on the MWCNT surfaces.Despite the limitations of these techniques,the results indicated that the dramatic increase in carboxyl groups was mainly responsible for the significant increase in oxygen content after the oxidation.The dissociation of the grafted functional groups increased electronegativity of the o-MWCNTs and facilitated the aqueous stabilization of o-MWCNTs through electrostatic repulsions.The oxidation affected the UV-Vis absorbance of MWCNT suspensions.The absorbances at 800 nm of the stabilized MWCNT suspensions had a good correlation with the MWCNT concentrations and could be used to quantify the MWCNT suspensions.The findings of this work are expected to boost the research on carbon nanotubes and their environmental behaviors.