A new horizontal continuous casting method with heating-cooling combined mold （HCCM） technology was explored for fabri- cating high-quality thin-wall cupronickel alloy tubes used for heat exchange pipes. The microst...A new horizontal continuous casting method with heating-cooling combined mold （HCCM） technology was explored for fabri- cating high-quality thin-wall cupronickel alloy tubes used for heat exchange pipes. The microstructure and mechanical properties of BFe 10 cupronickel alloy tubes fabricated by HCCM and traditional continuous casting （cooling mold casting） were comparatively investigated. The results show that the tube fabricated by HCCM has smooth internal and external surfaces without any defects, and its internal and external surface roughnesses are 0.64 μm and 0.85 μm, respectively. The tube could be used for subsequent cold processing without other treatments such as surface planning, milling and acid-washing. This indicates that HCCM can effectively reduce the process flow and improve the pro- duction efficiency of a BFel0 cupronickel alloy tube. The tube has columnar grains along its axial direction with a major casting texture of {012}〈 621 〉. Compared with cooling mold casting （6 = 36.5%）, HCCM can improve elongation （3 = 46.3%） by 10% with a slight loss of strength, which indicates that HCCM remarkably improves the cold extension performance of a BFe 10 cupronickel alloy tube.展开更多
Based on horizontal continuous casting with a heating-cooling combined mold （HCCM） technology, this article investigated the effects of processing parameters on the liquid-solid interface （LSI） position and the in...Based on horizontal continuous casting with a heating-cooling combined mold （HCCM） technology, this article investigated the effects of processing parameters on the liquid-solid interface （LSI） position and the influence of LSI position on the surface quality, microstructure, texture, and mechanical properties of a BFe10-1-1 tube （φ50 mm × 5 mm）. HCCM efficiently improves the temperature gradient in front of the LSI. Through controlling the LSI position, the radial columnar-grained microstructure that is commonly generated by cooling mold casting can be eliminated, and the axial columnar-grained microstructure can be obtained. Under the condition of 1250℃ melting and holding temperature, 1200-1250℃ mold heating temperature, 50-80 mm/min mean drawing speed, and 500-700 L/h cooling water flow rate, the LSI position is located at the middle of the transition zone or near the entrance of the cooling section, and the as-cast tube not only has a strong axial columnar-grained microstructure （{hkl}〈621〉, {hkl}〈221〉） due to strong axial heating conduction during solidification but also has smooth internal and external surfaces without cracks, scratches, and other macroscopic defects due to short solidified shell length and short contact length between the tube and the mold at high temperature. The elongation and tensile strength of the tube are 46.0%-47.2% and 210-221 MPa, respectively, which can be directly used for the subsequent cold-large-strain processing.展开更多
mole fraction) yttria-stabilized zirconia electrolyte thin wall tubes were p repared by i mproved slip casting method. The length and wall thickness of the tubes are 266 mm and 0.4～0.9 mm, respectively and the relat...mole fraction) yttria-stabilized zirconia electrolyte thin wall tubes were p repared by i mproved slip casting method. The length and wall thickness of the tubes are 266 mm and 0.4～0.9 mm, respectively and the relative density is 96.7%. The microstr ucture and electrical properties of samples sintered at different temperatures w ere studied using SEM and ac impedance spectroscopy. The effect of sintered dens ity, grain and grain boundary on the electrical properties of the samples was analyzed. The research results show that the density of the samples increase s gradually with increasing sintering temperatures. The microstructure of sample s strongly influences its electrical properties, and the electrical properti es of samples enhance with the increase of sintered density. The ionic conductiv ity of grain and grain boundary is increased as the sintering temperature incre ases. Better sinterability of the samples was obtained at the sintering temperat ure of 1650 ℃. The maximum open circuit voltage and short circuit current for s ingle cell is 0.946 V and 1.84 A, respectively. The maximum output power of sing le cell is 0.46 W at the temperature of 850 ℃.展开更多
The compositions, technical principles and construction equipments of a new piling method used for ground improvement plastic tube cast-in-place concrete pile were introduced. The results from static load tests on sin...The compositions, technical principles and construction equipments of a new piling method used for ground improvement plastic tube cast-in-place concrete pile were introduced. The results from static load tests on single piles with different forms of pile shoes and on their composite foundations were analyzed. The distribution patterns of axial force, shaft friction and toe resistance were studied based on the measurements taken from buried strain gauges. From the point of engineering application, the pile has merits in convenient quality control, high bearing capacity and reliable quality, showing higher reasonability, advancement and suitability than other ground improvement methods. The pile can be adopted properly to take place of ordinary ground improvement method, achieving greater economical and social benefits.展开更多
The microstructure of the thin-walled tubes with high-strength aluminum alloy determines their final forming quality and performance. This type of tube can be manufactured by multi-pass hot power backward spinning pro...The microstructure of the thin-walled tubes with high-strength aluminum alloy determines their final forming quality and performance. This type of tube can be manufactured by multi-pass hot power backward spinning process as it can eliminate casting defects, refine microstructure and improve the plasticity of the tube. To analyze the microstructure distribution characteristics of the tube during the spinning process, a 3D coupled thermo-mechanical FE model coupled with the microstructure evolution model of the process was established under the ABAQUS environment. The microstructure evolution characteristics and laws of the tube for the whole spinning process were analyzed. The results show that the dynamic recrystallization is mainly produced in the spinning deformation zone and root area of the tube. In the first pass, the dynamic recrystallization phenomenon is not obvious in the tube. With the pass increasing, the trend of dynamic recrystallization volume percentage gradually increases and extends from the outer surface of the tube to the inner surface. The fine-grained area shows the states of concentration, dispersion, and re-concentration as the pass number increases. .展开更多
基金supported by the National High Technology Research and Development Program of China (No.2011BAE23B00)
文摘A new horizontal continuous casting method with heating-cooling combined mold （HCCM） technology was explored for fabri- cating high-quality thin-wall cupronickel alloy tubes used for heat exchange pipes. The microstructure and mechanical properties of BFe 10 cupronickel alloy tubes fabricated by HCCM and traditional continuous casting （cooling mold casting） were comparatively investigated. The results show that the tube fabricated by HCCM has smooth internal and external surfaces without any defects, and its internal and external surface roughnesses are 0.64 μm and 0.85 μm, respectively. The tube could be used for subsequent cold processing without other treatments such as surface planning, milling and acid-washing. This indicates that HCCM can effectively reduce the process flow and improve the pro- duction efficiency of a BFel0 cupronickel alloy tube. The tube has columnar grains along its axial direction with a major casting texture of {012}〈 621 〉. Compared with cooling mold casting （6 = 36.5%）, HCCM can improve elongation （3 = 46.3%） by 10% with a slight loss of strength, which indicates that HCCM remarkably improves the cold extension performance of a BFe 10 cupronickel alloy tube.
基金financial support of National Key Technology R&D Program of China (No.2011BAE23B00)
文摘Based on horizontal continuous casting with a heating-cooling combined mold （HCCM） technology, this article investigated the effects of processing parameters on the liquid-solid interface （LSI） position and the influence of LSI position on the surface quality, microstructure, texture, and mechanical properties of a BFe10-1-1 tube （φ50 mm × 5 mm）. HCCM efficiently improves the temperature gradient in front of the LSI. Through controlling the LSI position, the radial columnar-grained microstructure that is commonly generated by cooling mold casting can be eliminated, and the axial columnar-grained microstructure can be obtained. Under the condition of 1250℃ melting and holding temperature, 1200-1250℃ mold heating temperature, 50-80 mm/min mean drawing speed, and 500-700 L/h cooling water flow rate, the LSI position is located at the middle of the transition zone or near the entrance of the cooling section, and the as-cast tube not only has a strong axial columnar-grained microstructure （{hkl}〈621〉, {hkl}〈221〉） due to strong axial heating conduction during solidification but also has smooth internal and external surfaces without cracks, scratches, and other macroscopic defects due to short solidified shell length and short contact length between the tube and the mold at high temperature. The elongation and tensile strength of the tube are 46.0%-47.2% and 210-221 MPa, respectively, which can be directly used for the subsequent cold-large-strain processing.
文摘mole fraction) yttria-stabilized zirconia electrolyte thin wall tubes were p repared by i mproved slip casting method. The length and wall thickness of the tubes are 266 mm and 0.4～0.9 mm, respectively and the relative density is 96.7%. The microstr ucture and electrical properties of samples sintered at different temperatures w ere studied using SEM and ac impedance spectroscopy. The effect of sintered dens ity, grain and grain boundary on the electrical properties of the samples was analyzed. The research results show that the density of the samples increase s gradually with increasing sintering temperatures. The microstructure of sample s strongly influences its electrical properties, and the electrical properti es of samples enhance with the increase of sintered density. The ionic conductiv ity of grain and grain boundary is increased as the sintering temperature incre ases. Better sinterability of the samples was obtained at the sintering temperat ure of 1650 ℃. The maximum open circuit voltage and short circuit current for s ingle cell is 0.946 V and 1.84 A, respectively. The maximum output power of sing le cell is 0.46 W at the temperature of 850 ℃.
基金Project (2007H03) supported by Communications Department of Zhejiang Province
文摘The compositions, technical principles and construction equipments of a new piling method used for ground improvement plastic tube cast-in-place concrete pile were introduced. The results from static load tests on single piles with different forms of pile shoes and on their composite foundations were analyzed. The distribution patterns of axial force, shaft friction and toe resistance were studied based on the measurements taken from buried strain gauges. From the point of engineering application, the pile has merits in convenient quality control, high bearing capacity and reliable quality, showing higher reasonability, advancement and suitability than other ground improvement methods. The pile can be adopted properly to take place of ordinary ground improvement method, achieving greater economical and social benefits.
文摘The microstructure of the thin-walled tubes with high-strength aluminum alloy determines their final forming quality and performance. This type of tube can be manufactured by multi-pass hot power backward spinning process as it can eliminate casting defects, refine microstructure and improve the plasticity of the tube. To analyze the microstructure distribution characteristics of the tube during the spinning process, a 3D coupled thermo-mechanical FE model coupled with the microstructure evolution model of the process was established under the ABAQUS environment. The microstructure evolution characteristics and laws of the tube for the whole spinning process were analyzed. The results show that the dynamic recrystallization is mainly produced in the spinning deformation zone and root area of the tube. In the first pass, the dynamic recrystallization phenomenon is not obvious in the tube. With the pass increasing, the trend of dynamic recrystallization volume percentage gradually increases and extends from the outer surface of the tube to the inner surface. The fine-grained area shows the states of concentration, dispersion, and re-concentration as the pass number increases. .
