CATIONIC POLYMERIZATION OF ISOBUTYLENE COINITIATED BY AICI_3 IN THE PRESENCE OF ETHYL BENZOATE

The cationic polymerizations of isobutylene （IB） coinitiated by AlCl3 were carried out in solvent mixture of nhexane/methylene dichloride （n-hex/CH2Cl2） of 60/40 V/V in the presence of ethyl benzoate （EB） at various temperatures range from -80℃ to -30℃. The effects of EB concentration （[EB]） and polymerization temperature on monomer conversion, weight-average molecular weight （Mw） and molecular weight distribution （MWD, Mw/Mn） of polyisobutylene （PIB） products were investigated. The rate of polymerization decreased while Mw of PIB products increased with increasing [EB]. The polymers with high molecular weight could be prepared in the presence of a suitable amount of EB. Significantly, the polymers with high Mw of 80.2 × 10^4 and 65.4 × 10^4 could be produced at -80℃ and -70℃ at [EB] = 0.24 × 10^3 mol/L respectively, which were much higher than that （Mw = 57.9 × 10^4） of PIB prepared at -100℃ in the absence ofEB. A simple but effective method for preparing the high molecular weight polyisobutylenes was developed in this work. It has been also found that the activation energy for propagation （Ep） depended on the polymerization temperature range in the presence of EB. An obvious inflection of the linear plots of lnXn versus 1/Tp occurred at the temperature range from -60℃ to -50℃ at four different concentrations of EB from 0.19 × 10^3 mol/L to 0.33× 10^3 tool/L, and thus the inflection temperature （Tinf） was in the range of -60℃ to -50℃. When [EB] was in the range of 0.24 × 10^3 mol/L to 0.33× 10^3 mol/L, Ep was determined to be around -12 kJ/mol when the polymerization was carried out at temperatures from -80℃ to Tinf and to be around -28 kJ/mol at temperatures from Tinf to -15℃ respectively.

Cationic Ring Opening Polymerization of Octamethylcyclotetrasiloxane Initiated by Acid Treated Bentonite

Cationic ring opening polymerization of octamethylcyclotetrasiloxane （Da） initiated by acid treated bentonite was investigated. The experimental conditions were chosen on the basis of preliminary experiments.Higher temperature was found beneficial for the reaction process while stirring intensity beyond a certain level showed no obvious effect on the reaction rate. Polymers were characterized by Fourier transform infrared, proton nuclear magnetic resonance （IH-NMR） and gel perneation chromotography. The width of molecular mass distribution was found ranging between 1.2 and 1.4, which is extraordinarlly narrow compared with that of cationic polymerizations reported elsewhere （〉 1.9）. The results were believed due to the absence of free proton and counter ion which simplifies the polymerization process and the huge steric hindrance provided by bentonite particles which keeps the propagation of polysiloxane onto the surface of bentonite particles in a much more regular way. A feasible mechanism is proposed and seems to be supported well by experiments. Additionally, from the results of α, ω-dihydrogen terminated polysiloxanes prepared, the possibility of applying this potential environmentally friendly heterogeneous catalyst in industrial polymerization of cyclosiloxanes is anticipated.

SYNTHESIS OF POLYISOBUTYLENE WITH SEC-ARYLAMINO TERMINAL GROUP BY COMBINATION OF CATIONIC POLYMERIZATION WITH ALKYLATION

The highly reactive polyisobutylenes(PIBs) withα-double bonds(87.5 mol%) or tert-chloro(tert-Cl) groups(95 mol%) could be prepared via the cationic polymerization of isobutylene(IB) coinitiated by BF_3 or TiCl_4 respectively.The Friedel-Crafts alkylation of diphenylamine(DPA) with the highly reactive PIB withα-double bonds was further conducted under different conditions,such as at different alkylation temperature,in the mixed solvents of CH_2Cl_2/n-hexane with different solvent polarity and at DPA concentr...

Cationic ring-opening polymerization of 3,3-bis(chloromethyl)oxacyclobutane in ionic liquids

Cationic ring-opening polymerization of 3,3-bis（chloromethyl）oxacyclobutane catalyzed by BF3.OEt2 was carded out in ionic liquids [bmim]BF4 and [bmim]PF6. The influences of BCMO concentration and molar ratio of BCMO/BF3.OEt2 on the molecular weights and yield of PBCMO were investigated. The polymerization in ionic liquids proceed to high conversions, although molecular weights are limited, similar to polymerization in organic solvent such as CH2Cl2. Follow a viewpoint of green chemistry, we feel ionic liquid [bmim]BF4 is superior to [bmim]PF6. Extracting [bmim]PF6 from the product using organic solvent as extractant limits its advantage as a green reaction media.

Synthesis and Characterization of Star-branched Polyisobutylene by Combination of Anionic Polymerization and Cationic Polymerization

A star-shaped multifunctional styrene-isoprene copolymer was synthesized with n-BuLi as initiator, divinyl benzene as coupling agent, cyclobexane as solvent by living anionic polymerization. Using this polymer as grafting agent, a novel star-shaped branched polymer, containing several polyisobutylene, was prepared via cationic ~aolymerization. The star PS-b-PI and star-branched polyisobutylene were characterized by GPC, ＇HNMR and FT-IR, and the effects of different adding order and the amount of grafting agent were investigated.

STUDY ON THE CATIONIC POLYMERIZATION OF 1, 3-PENTADIENE INITIATED BY AlCl_3/ALKYL HALIDE SYSTEMS

The cationic polymerizations of 1, 3-pentadiene were initiated by AlCl_3 in n-hexaneat 30℃ in the presence of alkyl halides, i.e., tert-butyl chloride, tert-butyl bromide andisobutyl chloride. The effects of these halides on the polymer yield, molecular weight,crosslinking reaction, cyclization and polymer microstructure, have been investigated. Twomain side reactions, crosslinking and cyclization, were suppressed and reduced by theaddition of the halides. The proportion of 1, 4 units of polymer chains was increasedby the presence of the halides, which reduced the polymer yield and the molecular weightof polymers.

(CH_3)_3SiCl/TiCl_4 INITIATING SYSTEM FOR CATIONIC POLYMERIZATION OF 1,3-PENTADIENE

Cationic polymerizations of 1,3-pentadiene (PD) initiated by trimethylsilyl chloride (TMSCl) incombination with TiCl_4 were carried out in n-hexane at 30℃. The yield of polymer was greatly increased bythe addition of TMSCl, indicating that the TMSCl/TiCl_4 combination is an efficient initiating system for PDcationic polymerization. However, the introduction of TMSCl gave rise to a drop in the molecular weight ofthe polymer. Kinetic results demonstrated that the polymerization initiated by TMSCl/TiCl_4 is 4.5 times fasterthan that induced by TiCl_4 alone. Various ethers were used to mediate the TMSCl/TiCl_4 initiating system.Adding diphenyl ether could increase both the yield and molecular weight of the polymer. Structural evidenceillustrates that the polymerization is indeed initiated by TiCl_4 in combination with HCl resulting fromhydrolysis by adventitious water.

CATIONIC POLYMERIZATION OF 1,3—PENTADIENE INITIATED BY ORGANIC AZIDE/Et_2AlCl

The cationic polymerization of 1, 3-pentadiene was initiated by the organic azide/Et_2 AlClinitiating system in CH_2Cl_2 and n-hexane. The polymerizations were also carried out in parallelwith organic chloride/Et_2AlCl and Et_2 AlCl alone for comparison. The Et_2 AlCl- induced polymer-ization gives a low yield while the polymerization initiated by organic chloride/Et_2 AlCl producesmainly insoluble product. In contrast, the polymerization with azide/Et,AlCl has a high conver-sion and the resulting polymer having a high molecular weight is totally soluble. The SEC spectraof the polymers have clearly shown the differences between these initiating systems.

SYNTHESIS AND CATIONIC RING-OPENING POLYMERIZATION OF 1, 4-ANHYDRO-2, 3-DI-O-(P-AZIDOBENZYL)-α-D-RIBOPYRANOSE

New highly stereoregular 2, 3 -di- O-(p-azidobenzyl )-(1 →5 ) - α-D -ribofuranan was synthesized byselective ring-opening polymerization of 1, 4-anhydro-2, 3 - di-O -(p-azidobenzyl )-α-D -ribopyranose(ADABR) using phosphorus pentafluoride or tin tetrachloride as catalyst at low temperature indichloromethane. The monomer was obtained by the reaction of p - bromomethyl -phenyleneazide with 1, 4 -anhydro-α-D-ribose in DMF. The structure of poly(ADANR) was identified by specific rotation and ^(13)C-NMR spectroscopy. Acid chloride-AgCl_4 complex catalyst such as CH_2=C(CH_3)C^+OClO_4^- used in thepolymerization resulted in polymers with mixed structures, i.e. (1→5)-α-D-ribofuranosidic and (1→4)-β-D-ribopyranosidic units. However, with C_6H_5C^+OClO_4^- as catalyst, pure (1→5)-α-D-ribofuranan was obtained.The effects of catalyst, polymerization temperature and time on polymer stereoregularity were examined, andthe mechanism of the ring-opening polymerization was discussed.

Emulsion Polymerization of Vinyl Acetate in the Presence of a New Cationic Surfactant

In this study, the emulsion homopolymerization system containing vinyl acetate, potassium persulfate, a new cationic polymeric surfactant and water was studied by the applying semi-continuous emulsion polymerization process. The effects of new polymeric emulsifier on the physicochemical properties of obtained vinyl acetate latexes were investigated depending on vinyl acetate percentage in the polymerization recipe, and two thermal initiators in homopolymerization.

Organic Brønsted Acid-Catalyzed Stereoselective Cationic RAFT Polymerization:The Effect of RAFT Agents

The tacticity of vinyl polymers is a key factor affecting the properties of materials.Recently,organic Brønsted acids have been demonstrated as effective catalysts for the development of highly stereoselective cationic reversible addition-fragmentation chain transfer(RAFT)polymerizations of vinyl ethers,in which the use of RAFT agents could allow the control the molecular weight and tacticity of polymer products simultaneously.However,the effect of RAFT agents on the tacticity-regulation remains elusive and lacks of investigation.In this study,we synthesized four types of RAFT agents and evaluated their influence in the stereoselective cationic polymerization of isobutyl vinyl ether in the presence of PADI as a Brønsted acid catalyst,which unveils that the Z group of RAFT agents could not only affect the polydispersity of the products,but also exert a profound effect on the stereoselectivity.After extensive screening of the RAFT agents,high stereoregularity(isotacticity,90%m)was obtained when using dithiocarbonate ester-type RAFT agents with a benzyloxy Z group.

RESEARCH ON CATIONIC POLYMER WATER BASE DRILLING FLUIDS

Cationic polymer drilling fluid (CPDF) is a new water base drilling fluid in which high molecular weight (HMW) cationic polymer (CPAM) is an encapsulating and flocculating agent and organic quaternary ammonium compound (NW-1) acts as shale inhibitor. This paper describes the experimental results of cuttings recovery, particle size distribution layer spacing and Zeta potential, and discusses the inhibition of CPDF system and its major additives. The advantages of CPDF will be proved by its application in well LX-2.

APPLICATION OF CATIONIC POLYMERIC MICROPARTICLES ON RETENTION AND DRAINAGE

The conditions of preparation and performance of a new structure of cationic organic polymeric micropaticles (CPMP) mainly composed of styrene and DADMAC were studied. And its application on retention and drainage on bleached hardwood pulp was investigated and compared with that of APAM and CPAM. The results show that the retention and drainage of CPMP on pulp is in positive proportion to the rise of the potential of the solution, and the first-pass retention ratio of bleached hardwood pulp goes up with the increase of the CPMP content. The functions of CPMP and CPAM are affected less by the shear force and the pH value of the system compared to that of APAM, and effect on retention of CPMP3 is appropriate to that of CPAM, but superior to that of APAM.

Preparation of cationic polyacrylamide microsphere emulsion and its performance for permeability reduction

In this paper, cationic polyacrylamide microspheres （CPAM） were synthesized using acrylamide （AM） and methacryloyloxyethyl trimethyl ammonium chloride （TMAEMC） as monomers, ammonium sulfate as dispersant, poly（acryloyloxyethyl trimethyl ammonium chloride） （PAETAC） as dispersion stabilizer, and ammonium persulfate as initiator. The synthetic method was dispersion polymerization. The effects of monomer ratio （AM/TMAEMC）, dispersant concentration, and dispersion stabilizer dosage on dispersion polymerization were systematically studied to determine the optimal preparation conditions. The structure and viscosity of the synthesized polymer were characterized by FTIR and capillary viscometry, respectively, and the particle sizes and distribution of the polymer microspheres were characterized by microscopy and dynamic light scattering, respectively. Finally, flow tests were conducted to measure the permeability reduction performance of the microspheres at various concentrations in sand packs with different permeability. Results show that CPAM emulsion of a solids content of 1 wt% has excellent performance in low-to-medium permeability formations （〈 1,000 mD）, and the efficiency may reach above 90%.

Preparation of Cationic Chitosan-Polyacrylamide Flocculant and Its Properties in Wastewater Treatment

Chitosan derived from crab shells, was used to prepare the graft polymer in aqueous solution with acrylamide （AM） and methacrylatoethyl trimethyl ammonium chloride （DMC） as raw materials and ceric ammonium nitrate （CAN） as initiator. The flocculation ability of the resulting polymer （PCAD） was studied in waste water treatment experiments. Its properties were determined on the basis of the transmittance of waste water after flocculation. The effects of ehitosan and DMC content on PCAD＇s flocculation ability were studied. Floeculation experiments were also undertaken under various pH conditions. According to the experimental data, the flocculation ability could be improved when chitosan content decreased in the raw material, but the monomer conversion would decrease obviously. When the ehitosan＇s content was more than 65%, AM and DMC groups were less on each chitosan molecule. So PCAD＇s flocculation ability was poor. Similarly, high content of DMC would result in low monomer conversion and high flocculation ability. PCAD molecules with more DMC group had more positive charges. It was favorable to flocculation. However, monomer conversion would decrease with the increase of DMC content. The suitable conditions were that chitosan and DMC contents were 65% and 15-20%, respectively. The experiment data showed that PCAD had good flocculation ability under weak acidic condition. Its ability would be weakened by strong acidic or alkaline condition. The flocculation efficiency was the best at pH of 5.5 when PCAD＇s dosage was 8mg-Lk Compared with cationic polymer （the copolymer of AM and DMC, PAD）, PCAD showed better flocculation ability under acid and neutral conditions, but worse ability under alkaline condition.

Synthesis and Characterization of Alkoxy and Phenoxy-substituted Ferrocenium Salt Cationic Photoinitiators

Alkyl-substituted ferrocenium salts have limited solubility in epoxy oligomers and produce poisonous arene by photolysis. Herein, the synthesis and photoactivity of several alkoxy-substituted ferrocenium salts as long-wavelength UV light photoinitiators have been reported. [Cyclopendadien-Fe-anisole]PF6, [Cyclopendadien-Fe-anisole]BF4, [Cyclopendadien-Fe-diphenylether]PF6, [Cyclopendadien-Fe-diphenylether]BF4. and [Cyclopendadien-Fe-diethoxybenzene] PF6 for polymerization of epoxy resin were prepared through the ligand exchange reaction between one ring of ferrocene and aromatic ether. They all display good solubility and photoinitiating activities in epoxy resins.

Novel Ferricenium Tetrafluoroborate Salt as Latent Thermal Cationic Initiator for Curing of Epoxy Resins

A novel latent thermal initiator, ferricenium tetrafluoroborate salt (FcBF4), for cationic polymerization of epoxides is reported. The activities of FcBF4 for different epoxides, including bisphenol-A-type epoxy oligomer E44, cycloaliphatic epoxy ERL4221, and glycidylether epoxy GGE, were evaluated by differential scanning calorimetry (DSC). The results showed a moderate thermal initiation activity for E44 and GGE at 78℃ and 108℃ respectively. When adding GGE to E44, the reaction was enhanced. The temperature of thermal degradation of the cured specimens for the system of E44/FcBF4, E44+10%GGE/FcBF4 and E44+10%ERL4221/FcBF4 is higher than 350℃.

Scalable, Green Chain Transfer Agent for Cationic RAFT Polymerizations

Cationic polymerizations of vinyl ethers have gained recent attention due to their ability to produce robust,biorenewable materials.These developments have been largely enabled by the advent of cationic reversible addition−fragmentation chain-transfer(RAFT)polymerization;however,the scalability and sustainability of this method are hindered by current chain-transfer agents(CTAs),which exist as viscous,colored oils requiring complex syntheses and solvent-intensive purification.Herein,we produce a solid,colorless CTA through a green synthetic route in 83%yield on a 50-gram scale.We investigate the utility of this CTA in chemical,electrochemical,photochemical,and acid-initiated methods,revealing that it achieves efficient polymerization with excellent control over molecular weight,low dispersity values,high chain end fidelity,and temporal control in cationic RAFT polymerizations.

Synthesis and Characterization of Alkoxy and Phenoxy-substituted Ferrocenium Salt Cationic Photoinitiators

Alkyl-substituted ferrocenium salts have limited solubility in epoxy oligomers and produce poisonous arene by photolysis. Herein, the synthesis and photoactivity of several alkoxy-substituted ferrocenium salts as long-wavelength UV light photoinitiators have been reported. [Cyclopendadien-Fe-anisole]PF6, [Cyclopen- dadien-Fe-anisole]BF4, [Cyclopendadien-Fe-diphenylether]PF6, [Cyclopendadien-Fe-diphenylether]BF4, and [Cyclopendadien-Fe-diethoxybenzene] PF6 for polymerization of epoxy resin were prepared through the ligand exchange reaction between one ring of ferrocene and aromatic ether. They all display good solubility and photoini- tiating activities in epoxy resins.