好氧堆肥对生物炭理化性质及吸附Cd^(2+)稳定性的影响

生物炭可作为畜禽粪污好氧堆肥中去除重金属的功能材料,但堆体内部复杂的环境变化会影响生物炭的理化性质,从而影响其对重金属吸附的稳定性。将普通秸秆生物炭(BC)和磁性秸秆生物炭(FBC)置于牛粪中进行30 d好氧堆肥试验,研究两种生物炭基本理化性质及对Cd^(2+)吸附稳定性的影响。结果表明:堆肥处理使BC和FBC的比表面积分别增加20.56%和76.64%,总孔容分别下降2.36%和3.70%,平均孔径分别下降19.17%和46.54%,表面官能团发生变化,FBC的饱和磁化强度下降43.67%。堆肥后,饱和吸附Cd^(2+)的两种生物炭BC和FBC的TCLP提取态Cd(TCLP-Cd)占比和TCLP提取液pH(TCLP-pH)均呈下降趋势,其中TCLP-Cd占比分别从28.31%和22.85%显著下降至26.76%和13.85%(P<0.05),TCLP-pH分别从3.66和3.29显著下降至3.51和3.14。综上,堆肥老化改变了两种生物炭的理化性质,降低了其酸可提取态Cd的含量,提高了其吸附Cd 2+的稳定性,且FBC中Cd^(2+)的稳定性更强。

Cd^(2+)浓度对好氧颗粒污泥EPS各组分形成的影响

为探究重金属Cd^(2+)对好氧颗粒污泥系统运行的影响,采用紫外分析法和三维荧光光谱分析法研究了SBR反应器中不同浓度的重金属Cd^(2+)对好氧颗粒污泥EPS总量以及各组分(LB-EPS、SB-EPS、TB-EPS)的产生与组成成分的影响。试验结果表明:低浓度Cd^(2+)(小于0.1mg/L)促进EPS的产生,高浓度Cd^(2+)(大于3mg/L)抑制EPS的产生;SB-EPS随着Cd^(2+)浓度的增加逐渐减少,其中蛋白质含量增加,多糖、腐殖酸明显减少;当Cd^(2+)浓度小于0.1mg/L时TB-EPS显著增加,其中主要增加的成分是蛋白质;当Cd^(2+)浓度大于3mg/L时,TB-EPS的分泌受到抑制,但蛋白质含量仍高于空白对照组,多糖、腐殖酸含量显著降低;LB-EPS受到的影响因素较多,其含量变化不规律。采用扩展DLVO理论剖析了EPS各组分含量的变化对好氧颗粒污泥沉降性能的影响,以期为好氧颗粒化技术在工业废水处理中的应用提供有力的支持。

羧甲基改性沙柳木粉膜吸附Cd^(2+)的性能研究

沙柳木粉(SPP)经醚化反应制备成羧甲基沙柳木粉(CMS)。将CMS溶解到1-丙烯基-3-甲基咪唑氯盐(AMIMJCI)和二甲基亚砜(DMSO)中,采用聚乙烯醇(PVA)为成膜剂,制备羧甲基沙柳木粉膜(CMSM)。探究在不同吸附条件下CMSM对Cd^(2+)的吸附性能。采用FTIR、SEM、XRD和XPS对CMSM进行表征。吸附结果表明:Cd^(2+)初始浓度为800mg·L^(-1),pH值为5,吸附时间105min,吸附温度35℃时,CMSM对Cd^(2+)的吸附效果最佳。表征结果表明:0-H、-COOH、-C-O-C-、-CH_(2)、-NH_(2),基团参与吸附Cd^(2+)的反应。CMSM表面比较疏松,有孔隙,成狭缝型。CMSM晶体内部变得蓬松,Cd^(2+)更容易被CMSM吸附。CMSM对Cd^(2+)的吸附属于多分子层吸附,同时存在化学吸附和物理吸附,且以化学吸附为主,准二级动力学模型和Freundlich等温线模型与其吸附过程相符合。

Co-doped BaFe_(2)As_(2) Josephson junction fabricated with a focused helium ion beam

Josephson junction plays a key role not only in studying the basic physics of unconventional iron-based superconductors but also in realizing practical application of thin-film based devices,therefore the preparation of high-quality iron pnictide Josephson junctions is of great importance.In this work,we have successfully fabricated Josephson junctions from Co-doped BaFe_(2)As_(2)thin films using a direct junction fabrication technique which utilizes high energy focused helium ion beam(FHIB).The electrical transport properties were investigated for junctions fabricated with various He^(+)irradiation doses.The junctions show sharp superconducting transition around 24 K with a narrow transition width of 2.5 K,and a dose correlated foot-structure resistance which corresponds to the effective tuning of junction properties by He^(+)irradiation.Significant J_c suppression by more than two orders of magnitude can be achieved by increasing the He^(+)irradiation dose,which is advantageous for the realization of low noise ion pnictide thin film devices.Clear Shapiro steps are observed under 10 GHz microwave irradiation.The above results demonstrate the successful fabrication of high quality and controllable Co-doped BaFe_(2)As_(2)Josephson junction with high reproducibility using the FHIB technique,laying the foundation for future investigating the mechanism of iron-based superconductors,and also the further implementation in various superconducting electronic devices.

Hierarchically Structured Nb_(2)O_5 Microflowers with Enhanced Capacity and Fast-Charging Capability for Flexible Planar Sodium Ion Micro-Supercapacitors

Planar Na ion micro-supercapacitors(NIMSCs) that offer both high energy density and power density are deemed to a promising class of miniaturized power sources for wearable and portable microelectron-ics. Nevertheless, the development of NIMSCs are hugely impeded by the low capacity and sluggish Na ion kinetics in the negative electrode.Herein, we demonstrate a novel carbon-coated Nb_(2)O_5 microflower with a hierarchical structure composed of vertically intercrossed and porous nanosheets, boosting Na ion storage performance. The unique structural merits, including uniform carbon coating, ultrathin nanosheets and abun-dant pores, endow the Nb_(2)O_5 microflower with highly reversible Na ion storage capacity of 245 mAh g^(-1) at 0.25 C and excellent rate capability.Benefiting from high capacity and fast charging of Nb_(2)O_5 microflower, the planar NIMSCs consisted of Nb_(2)O_5 negative electrode and activated car-bon positive electrode deliver high areal energy density of 60.7 μWh cm^(-2),considerable voltage window of 3.5 V and extraordinary cyclability. Therefore, this work exploits a structural design strategy towards electrode materials for application in NIMSCs, holding great promise for flexible microelectronics.

电化学快速合成UiO-66及构建电化学传感器检测Cd^(2+)

由于目前合成UiO-66需要高温和长时的苛刻条件,本文采用电化学方法,在无需添加锆盐、常温和2 h的条件下快速合成出UiO-66,并用其制备UiO-66/玻碳电极(GCE)构建电化学传感器检测Cd^(2+)。通过扫描电子显微镜(SEM)、傅立叶红外光谱(FT-IR)、 X射线衍射(XRD)和比表面积(BET)的表征及分析可知,合成的UiO-66为菱形十二面体结构,结晶度良好,比表面积较大,可达到1 054.455 m^(2)/g,总孔隙体积为0.709 cm3/g。同时,探索出最佳检测条件为:NaAc-HAc缓冲溶液pH值为5、富集电压为-1.0 V、富集时间为120 s。在最佳检测条件下,基于UiO-66构建的电化学传感器对Cd~(2+)的检测灵敏度为4.10 AM^(-1),最低检测限为0.037μM,显示出较好的检测Cd^(2+)性能,并且具有良好的重现性、稳定性和抗干扰性。回收实验表明,检测实际汾河水样效果良好。

课程实践融入《试验设计与数据处理》教学--改性花生壳吸附剂的制备及其对重金属Cd^(2+)的吸附性能研究

随着我国提出新工科建设路线,结合地方高校(贺州学院)的地域特色和应用型人才的培养目标,本文通过课程考核形式,设计一个利用花生壳为原料制备出改性花生壳吸附剂(MPS)的试验。学生通过对吸附剂的合成、表征、试验设计和数据分析等环节,将《试验设计与数据处理》课程中所学知识应用到实际试验中,加深对课程知识的理解,锻炼其实际应用能力。

Delving into the dissimilarities in electrochemical performance and underlying mechanisms for sodium and potassium ion storage in N-doped carbon-encapsulated metallic Cu_(2)Se nanocubes

The large volumetric variations experienced by metal selenides within conversion reaction result in inferior rate capability and cycling stability,ultimately hindering the achievement of superior electrochemical performance.Herein,metallic Cu_(2)Se encapsulated with N-doped carbon(Cu_(2)Se@NC)was prepared using Cu_(2)O nanocubes as templates through a combination of dopamine polymerization and hightemperature selenization.The unique nanocubic structure and uniform N-doped carbon coating could shorten the ion transport distance,accelerate electron/charge diffusion,and suppress volume variation,ultimately ensuring Cu_(2)Se@NC with excellent electrochemical performance in sodium ion batteries(SIBs)and potassium ion batteries(PIBs).The composite exhibited excellent rate performance(187.7 mA h g^(-1)at 50 A g^(-1)in SIBs and 179.4 mA h g^(-1)at 5 A g^(-1)in PIBs)and cyclic stability(246,8 mA h g^(-1)at 10 A g^(-1)in SIBs over 2500 cycles).The reaction mechanism of intercalation combined with conversion in both SIBs and PIBs was disclosed by in situ X-ray diffraction(XRD)and ex situ transmission electron microscope(TEM).In particular,the final products in PIBs of K_(2)Se and K_(2)Se_(3)species were determined after discharging,which is different from that in SIBs with the final species of Na_(2)Se.The density functional theory calculation showed that carbon induces strong coupling and charge interactions with Cu_(2)Se,leading to the introduction of built-in electric field on heterojunction to improve electron mobility.Significantly,the theoretical calculations discovered that the underlying cause for the relatively superior rate capability in SIBs to that in PIBs is the agile Na~+diffusion with low energy barrier and moderate adsorption energy.These findings offer theoretical support for in-depth understanding of the performance differences of Cu-based materials in different ion storage systems.

粉煤灰基P型沸石吸附水中Cu^(2+)和Cd^(2+)

以粉煤灰(FA)为原料经水热反应合成了P型沸石(Z-P).采用X射线荧光光谱仪、X射线衍射仪、场发射环境扫描电子显微镜、比表面孔径分析仪、傅里叶变换红外光谱仪和X射线光电子能谱对Z-P进行表征,并研究了其对Cu^(2+)和Cd^(2+)的吸附性能.结果表明,Z-P的BET比表面积和孔隙体积分别为38.46m^(2)/g和0.2180cm^(3)/g,均高于FA的1.273m^(2)/g和0.0120cm^(3)/g.FA、Z-P对Cu^(2+)和Cd^(2+)的吸附更符合拟二级动力学模型和Langmuir等温线模型.Z-P对Cu^(2+)和Cd^(2+)的最大吸附量分别为157.48,131.57mg/g,远高于于FA的30.88,25.47mg/g.Z-P对Cd^(2+)的循环再生吸附效果好,但对Cu^(2+)的循环再生吸附效果较差.离子强度对Z-P吸附Cu^(2+)和Cd^(2+)分别起促进和抑制作用.表明Z-P可以作为有效且廉价的Cu^(2+)、Cd^(2+)吸附剂,为FA的资源化利用和含Cu^(2+)、Cd^(2+)重金属离子废水吸附剂的开发提供了一种方法.

In Situ Growth of 2D Metal–Organic Framework Ion Sieve Interphase for Reversible Zinc Anodes

Zinc metal anodes are gaining popularity in aqueous electrochemical energy storage systems for their high safety,cost-effectiveness,and high capacity.However,the service life of zinc metal anodes is severely constrained by critical challenges,including dendrites,water-induced hydrogen evolution,and passivation.In this study,a protective two-dimensional metal–organic framework interphase is in situ constructed on the zinc anode surface with a novel gel vapor deposition method.The ultrathin interphase layer(~1μm)is made of layer-stacking 2D nanosheets with angstrom-level pores of around 2.1Å,which serves as an ion sieve to reject large solvent–ion pairs while homogenizes the transport of partially desolvated zinc ions,contributing to a uniform and highly reversible zinc deposition.With the shielding of the interphase layer,an ultra-stable zinc plating/stripping is achieved in symmetric cells with cycling over 1000 h at 0.5 mA cm−2 and~700 h at 1 mA cm^(−2),far exceeding that of the bare zinc anodes(250 and 70 h).Furthermore,as a proof-of-concept demonstration,the full cell paired with MnO_(2) cathode demonstrates improved rate performances and stable cycling(1200 cycles at 1 A g−1).This work provides fresh insights into interphase design to promote the performance of zinc metal anodes.

In situ luminescence measurements of GaN/Al_(2)O_(3) film under different energy proton irradiations

Ion beam-induced luminescence(IBIL) experiments were performed to investigate the in situ luminescence of GaN/Al_(2)O_(3) at varying ion energies,which allowed for the measurement of defects at different depths within the material.The energies of H^(+)were set to 500 keV,640 keV and 2 MeV,the Bragg peaks of which correspond to the GaN film,GaN/Al_(2)O_(3) heterojunction and Al_(2)O_(3) substrate,respectively.A photoluminescence measurement at 250 K was also performed for comparison,during which only near band edge(NBE) and yellow band luminescence in the GaN film were observed.The evolution of the luminescence of the NBE and yellow band in the GaN film was discussed,and both exhibited a decrease with the fluence of H^(+).Additionally,the luminescence of F centers,induced by oxygen vacancies,and Cr^(3+),resulting from the ^(2)E →^(4)A_(2) radiative transition in Al_(2)O_(3),were measured using 2 MeV H^(+).The luminescence intensity of F centers increases gradually with the fluence of H^(+).The luminescence evolution of Cr^(3+)is consistent with a yellow band center,attributed to its weak intensity,and it is situated within the emission band of the yellow band in the GaN film.Our results show that IBIL measurement can effectively detect the luminescence behavior of multilayer films by adjusting the ion energy.Luminescence measurement can be excited by various techniques,but IBIL can satisfy in situ luminescence measurement,and multilayer structural materials of tens of micrometers can be measured through IBIL by adjusting the energy of the inducing ions.The evolution of defects at different layers with ion fluence can be obtained.

Investigations on MoS_(2)plasma by infra-red pulsed laser irradiation in high vacuum

MoS_(2)targets were irradiated by infra-red(IR)pulsed laser in a high vacuum to determine hot plasma parameters,atomic,molecular and ion emission,and angular and charge state distributions.In this way,pulsed laser deposition(PLD)of thin films on graphene oxide substrates was also realized.An Nd:YAG laser,operating at the 1064 nm wavelength with a 5 ns pulse duration and up to a 1 J pulse energy,in a single pulse or at a 10 Hz repetition rate,was employed.Ablation yield was measured as a function of the laser fluence.Plasma was characterized using different analysis techniques,such as time-of-flight measurements,quadrupole mass spectrometry and fast CCD visible imaging.The so-produced films were characterized by composition,thickness,roughness,wetting ability,and morphology.When compared to the MoS_(2)targets,they show a slight decrease of S with respect to Mo,due to higher ablation yield,low fusion temperature and high sublimation in vacuum.The pulsed IR laser deposited Mo Sx(with 1<x<2)films are uniform,with a thickness of about 130 nm,a roughness of about 50 nm and a higher wettability than the MoS_(2)targets.Some potential applications of the pulsed IR laser-deposited Mo Sx films are also presented and discussed.

Polypyride intercalation boosting the kinetics and stability of V_(3)O_(7)·H_(2)O cathodes for aqueous zinc-ion batteries

V_(3)O_(7)·H_(2)O(VO)is a high capacity cathode material in the field of aqueous zinc ion batteries(AZIBs),but it is limited by slow ion migration and low electrical conductivity.In this paper,polypyridine(PPyd)intercalated VO with nanoribbon structure was prepared by a simple in-situ pre-intercalation,which is noted VO-PPyd.The total density of states(TDOS)shows that after the pre-intercalation of PPyd,an intermediate energy level appears between the valence band and conduction band,which provides a step that can effectively reduce the band gap and enhance the electron conductivity.Furthermore,the density functional theory(DFT)results found that Zn^(2+)is more easily de-intercalated from the V-O skeleton,which proves that the embeddedness of PPyd improves the diffusion kinetics of Zn^(2+).Electrochemical studies have shown that VO-PPyd cathode materials exhibit excellent rate performance(high specific capacity of 465 and 192 mA h g^(-1)at 0.2 and 10 A g^(-1),respectively)and long-term cycling performance(92.7%capacity retention rate after 5300 cycles),due to their advantages in structure and composition.More importantly,the energy density of VO-PPyd//Zn at 581 and 5806 W kg^(-1)is 375 and 247 W h kg^(-1),respectively.VO-PPyd exhibits excellent electrochemical properties compared to previously reported vanadium based cathodes,which makes it highly competitive in the field of high-performance cathode materials of AZIBs.

Half-integer Shapiro steps in MgB_(2) focused He ion beam Josephson junctions

Half-integer microwave induced steps(Shapiro steps)have been observed in many different Josephson junction systems,which have attracted a lot of attention because they signify the deviation of current phase relation(CPR)and uncover many unconventional physical properties.In this article,we first report the discovery of half-integer Shapiro steps in MgB_(2)focused He ion beam(He-FIB)Josephson junctions.The half-integer steps'dependence on microwave frequency,temperature,microwave power,and magnetic field is also analyzed.We find that the existence of half-integer steps can be controlled by the magnetic field periodically,which is similar to that of high temperature superconductor(HTS)grain boundary junctions,and the similarity of the microstructures between gain boundary junctions and He-FIB junctions is discussed.As a consequence,we mainly attribute the physical origin of half-integer steps in MgB_(2)He-FIB junctions to the model that a He-FIB junction is analogous to a parallel junctions'array.Our results show that He-FIB technology is a promising platform for researching CPR in junctions made of different superconductors.

An efficient strategy for the preparation of MIL-53(Al)-NH_(2)membranes with high ion selectivity and desalination performance

The efficient extraction of sodium(Na^(+))and lithium(Li^(+))from seawater and salt lakes is increasingly demanding due to their great application value in chemical industries.However,coexisting cations such as divalent calcium(Ca^(2+))and magnesium(Mg^(2+))ions are at the subnanometer scale in diameter,similar to target monovalent ions,making ion separation a great challenge.Here,we propose a simple and fast secondary growth method for the preparation of MIL-53(Al)-NH_(2)membranes on the surface of anodic aluminum oxide.Such membranes contain angstrom-scale(~7Å)channels for the entrance of small monovalent ions and water molecules,endowing the selectivities for monovalent cations over divalent cations and water over salt molecules.The resulting high-connectivity MIL-53(Al)-NH_(2)membranes exhibit excellent ion separation performance(a selectivity of 121.42 for Na^(+)/Ca^(2+)and 93.81 for Li^(+)/Mg^(2+))and desalination performance(a water/salt selectivity of up to 5196).This work highlights metal–organic framework membranes as potential candidates for realizing ion separation and desalination in liquid treatment.

Carrageenan Fiber Prepared by a New Process Route of Ba^(2+)Ion Pre-Crosslinking in the Spinning Solution

Ba^(2+)pre-crosslinked carrageenan fiber(Ba/CAF)was prepared by adding a small amount of Ba^(2+) to the carrageenan(CA)solution as the spinning solution.Ba/CAF-n/A,Ba/CAF-n/B and Ba/CAF-n/C were prepared with ethanol solution(combine A),high concentration BaCl_(2)solution(combine B)and low concentration BaCl_(2)solution(combine C),as coagulation bath and stretch bath,respectively.The combination of coagulation bath and stretch bath suitable for Ba^(2+) pre-crosslinking wet spinning was screened.The results showed that Ba^(2+) can induce the birefringence of the CA molecular chain,and the Ba^(2+) pre-crosslinking effect is the best when the CA mass fraction is 8.0 wt%.From the perspective of production safety,fiber performance and spinning cost,the coagulation bath of 3.5 wt%BaCl_(2)solution and stretch bath of 1.7 wt%BaCl_(2)solution,that is,combination C with low concentration BaCl_(2)solution,is the best choice.Ba/CAF-8.0/C was obtained under the best conditions.The linear intensity,water absorption and flame retardancy study showed that the breaking strength of Ba/CAF-8.0/C is as high as 1.61 cN/dtex,the water absorption was 649.2%and 574.3%,in deionized water and normal saline,respectively,and the LOI value reached 32.

High-performance magnesium/sodium hybrid ion battery based on sodium vanadate oxide for reversible storage of Na^(+)and Mg^(2+)

Magnesium ion batteries(MIBs)are a potential field for the energy storage of the future but are restricted by insufficient rate capability and rapid capacity degradation.Magnesium-sodium hybrid ion batteries(MSHBs)are an effective way to address these problems.Here,we report a new type of MSHBs that use layered sodium vanadate((Na,Mn)V_(8)O_(20)·5H_(2)O,Mn-NVO)cathodes coupled with an organic 3,4,9,10-perylenetetracarboxylic diimide(PTCDI)anode in Mg^(2+)/Na^(+)hybrid electrolytes.During electrochemical cycling,Mg^(2+)and Na^(+)co-participate in the cathode reactions,and the introduction of Na^(+)promotes the structural stability of the Mn-NVO cathode,as cleared by several ex-situ characterizations.Consequently,the Mn-NVO cathode presents great specific capacity(249.9 mA h g^(−1)at 300 mA g^(−1))and cycling(1500 cycles at 1500 mA g^(−1))in the Mg^(2+)/Na^(+)hybrid electrolytes.Besides,full battery displays long lifespan with 10,000 cycles at 1000 mA g^(−1).The rate performance and cycling stability of MSHBs have been improved by an economical and scalable method,and the mechanism for these improvements is discussed.

虾青素对镉离子(Cd^(2+))诱导下斑马鱼胚胎抗氧化指标的影响

(28.0±0.5)℃下,将100个产后1 h的斑马鱼(Danio rerio)胚胎放在120 mm培养皿中,暴露在<0.02%浓度的二甲基亚砜(DMSO,对照组)、50μg/L Cd^(2+)(低浓度暴露组)、500μg/L Cd^(2+)(高浓度暴露组)和Cd^(2+)+雨生红球藻(Haematococcus pluvialis)虾青素AST联合暴露组(50μg/L Cd^(2+)+100μg/L AST组和500μg/L Cd^(2+)+100μg/L AST组)5个处理组中,120 h后测定斑马鱼幼鱼活性氧(ROS)、丙二醛(MDA)和谷胱甘肽酶(GSH)含量、超氧化物歧化酶(SOD)活性和总抗氧化能力(T-AOC),研究重金属镉离子(Cd^(2+))暴露下斑马鱼胚胎的抗氧化响应,探讨AST对斑马鱼机体氧化损伤的缓解效果。结果表明,斑马鱼胚胎Cd^(2+)暴露120 h后,体内活性氧(ROS)和丙二醛(MDA)含量随着Cd^(2+)浓度的升高而增加;GSH含量、SOD和T-AOC的活性随着Cd^(2+)浓度的增加而降低。说明Cd^(2+)可诱导斑马鱼机体出现氧化应激和氧化损伤。添加AST后,斑马鱼幼鱼体内ROS和MDA含量下降,GSH含量、SOD和T-AOC活性上升,说明添加AST可在一定程度上缓解重金属Cd^(2+)对斑马鱼体内抗氧化指标的负面影响。本研究结果可为AST作为新型鱼类饲料添加剂提供理论依据。

复配修饰新疆灰漠土对Cd^(2+)的吸附性能研究

选用了两性离子型表面活性剂BS和阴离子型表面活性剂SDS,按照不同比例量配比,对新疆灰漠土进行了修饰,制备了8种修饰土样,以未经修饰的原土样(CK)为对照,在同样条件下分别对重金属离子Cd^(2+)的吸附性能进行了测试,通过Langmuir等温吸附模型描述Cd^(2+)在灰漠土中的吸附特征,结果表明以两性-阴离子表面活性剂体系复配修饰新疆灰漠土能够显著提升其对重金属离子Cd^(2+)的吸附性能。

Interfacial built-in electric field and crosslinking pathways enabling WS_(2)/Ti_(3)C_(2)T_(x) heterojunction with robust sodium storage at low temperature

Developing efficient energy storage for sodium-ion batteries(SIBs)by creating high-performance heterojunctions and understanding their interfacial interaction at the atomic/molecular level holds promise but is also challenging.Besides,sluggish reaction kinetics at low temperatures restrict the operation of SIBs in cold climates.Herein,cross-linking nanoarchitectonics of WS_(2)/Ti_(3)C_(2)T_(x) heterojunction,featuring built-in electric field(BIEF),have been developed,employing as a model to reveal the positive effect of heterojunction design and BIEF for modifying the reaction kinetics and electrochemical activity.Particularly,the theoretical analysis manifests the discrepancy in work functions leads to the electronic flow from the electron-rich Ti_(3)C_(2)T_(x) to layered WS_(2),spontaneously forming the BIEF and“ion reservoir”at the heterogeneous interface.Besides,the generation of cross-linking pathways further promotes the transportation of electrons/ions,which guarantees rapid diffusion kinetics and excellent structure coupling.Consequently,superior sodium storage performance is obtained for the WS_(2)/Ti_(3)C_(2)T_(x) heterojunction,with only 0.2%decay per cycle at 5.0 A g^(-1)(25℃)up to 1000 cycles and a high capacity of 293.5 mA h g^(-1)(0.1A g^(-1)after 100 cycles)even at-20℃.Importantly,the spontaneously formed BIEF,accompanied by“ion reservoir”,in heterojunction provides deep understandings of the correlation between structure fabricated and performance obtained.