Extraction Process Optimization of Total Flavonoids from Mallotus apelta Stems by Central Composite Design/Response Surface Method

[Objectives] To optimize the extraction process of total flavonoids in stems of Mallotus apelta. [Methods]On the basis of singlefactor test,with volume fraction of ethanol,extraction time and ratio of solvent as independent variables,the content of total flavonoids as dependent variables,the completely secondary response surface regression fitting was conducted on the independent and dependent variables,and the Response Surface Method was used to optimize the optimum extraction process of total flavonoids in Mallotus apelta stems and predict the optimum process. [Results] The optimum extraction process of total flavonoids in Mallotus apelta was determined as follows: ethanol concentration of 71. 5%; extraction time of 154. 6 min; solid-liquid ratio of 1∶19. 2; total flavonoids content of 7. 060 mg/g; fitted binomial squared correlation coefficient R^2= 0. 8751.[Conclusions]Composite Design/Response Surface Method could be used in the extraction process optimization of total flavonoids in Mallotus apelta stems,the mathematical model established had high prediction accuracy,the method was simple and operability was good.

Application of response surface methodology and central composite rotatable design for modeling the influence of some operating variables of the lab scale thickener performance

This study discussed the application of response surface methodology(RSM)and central composite rotatable design(CCRD)for modeling and optimization of the influence of some operating variables on the performance of a lab scale thickener for dewatering of tailing in the flotation circuit.Four thickener operating variables,namely feed flowrate,solid percent,flocculant dosage and feedwell height were changed during the tests based on CCRD.The ranges of values of the thickener variables used in the design were a feed flowrate of 9–21 L/min,solid percent of 8%–20%,flocculant dosage of 1.25–4.25 g/t and feedwell height of 16–26 cm.A total of 30 thickening tests were conducted using lab scale thickener on flotation tailing obtained from the Sarcheshmeh copper mine,Iran.The underflow solid percent and bed height were expressed as functions of four operating parameters of thickener.Predicted values were found to be in good agreement with experimental values(R2values of 0.992 and 0.997 for underflow solid percent and bed height,respectively).This study has shown that the RSM and CCRD could effciently be applied for the modeling of thickener for dewatering of flotation tailing.

Catalytic Hydrothermal Liquefaction of Water Hyacinth Using Fe3O4/NiO Nanocomposite: Optimization of Reaction Conditions by Response Surface Methodology

This research aimed at optimizing the reaction conditions for the catalytic hydrothermal liquefaction (HTL) of water hyacinth using iron oxide/nickel oxide nanocomposite as catalysts. The iron oxide/nickel oxide nanocomposite was synthesized by the co-precipitation method and used in the hydrothermal liquefaction of water hyacinth. The composition and structural morphology of the synthesized catalysts were determined using X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and atomic absorption spectroscopy (AAS). The particle size distribution of the catalyst nanoparticles was determined by the Image J software. Three reaction parameters were optimized using the response surface methodology (RSM). These were: temperature, residence time, and catalyst dosage. A maximum bio-oil yield of 59.4 wt% was obtained using iron oxide/nickel oxide nanocomposite compared to 50.7 wt% obtained in absence of the catalyst. The maximum bio-oil yield was obtained at a temperature of 320°C, 1.5 g of catalyst dosage, and 60 min of residence time. The composition of bio-oil was analyzed using gas chromatography-mass spectroscopy (GC-MS) and elemental analysis. The GC-MS results showed an increase of hydrocarbons from 58.3% for uncatalyzed hydrothermal liquefaction to 88.66% using iron oxide/nickel oxide nanocomposite. Elemental analysis results revealed an increase in the hydrogen and carbon content and a reduction in the Nitrogen, Oxygen, and Sulphur content of the bio-oil during catalytic HTL compared to HTL in absence of catalyst nanoparticles. The high heating value increased from 33.5 MJ/Kg for uncatalyzed hydrothermal liquefaction to 38.6 MJ/Kg during the catalytic HTL. The catalyst nanoparticles were recovered from the solid residue by sonication and magnetic separation and recycled. The recycled catalyst nanoparticles were still efficient as hydrothermal liquefaction (HTL) catalysts and were recycled four times. The application of iron oxide/ nickel oxide nanocomposites in the HTL of water hyacinth increases the yield of bio-oil and improves its quality by reducing hetero atoms thus increasing its energy performance as fuel. Iron oxide/nickel oxide nanocomposites used in this study are widely available and can be easily recovered magnetically and recycled. This will potentially lead to an economical, environmentally friendly, and sustainable way of converting biomass into biofuel.

Optimization of Extraction Process of Clerodendrum philippinum Schauer var. simplex Mlodenke Total Flavonoids(CPTF) by Central Composite Design-Response Surface Methodology

[Objectives] The research aimed to optimize extraction process of Clerodendrum philippinum Schauer var. simplex Mlodenke total flavonoids( CPTF),and provide reference for its development and utilization. [Methods] Based on single-factor test,ethanol concentration,extraction temperature and extraction time were taken as independent variables,and total flavonoids yield was taken as dependent variable. The test was conducted according to central composite design principle. Multivariate linear regression and binomial equation fitting of the result were conducted,and extraction process of CPTF was optimized by using response surface methodology. [Results]The optimal extraction process of CPTF was as below: ethanol concentration 54. 76%,extraction temperature 83. 92℃,extraction time 102. 64 min,solid-liquid ratio 1:20,extraction for twice. [Conclusions] The extraction process of CPTF by central composite design-response surface methodology was simple and feasible,with reliable prediction result,which was suitable for industrial production.

Optimization of Extraction Process of Total Flavonoids from Akebia trifoliata (Thunb.) Koidz. by Central Composite Design-Response Surface Methodology

[Objectives]To optimize extraction process of total flavonoids from Akebia trifoliata( Thunb.) Koidz.,so as to provide references for development and use of Akebia trifoliata( Thunb.) Koidz. [Methods]The extraction rate of total flavonoids of Akebia trifoliata( Thunb.)Koidz. was taken as observation indicator. On the basis of single factor experiment,central composite design( CCD) was used to evaluate the effects of the extraction temperature,extraction time,and ethanol concentration on the extraction process. Multiple linear regression and binomial fitting were used,and response surface methodology( RSM) was used to select the optimum extraction process. [Results] The optimum extraction process conditions for total flavonoids of Akebia trifoliata( Thunb.) Koidz. was extraction temperature: 83. 92 ℃; extraction time:96. 47 min; ethanol concentration: 63. 92%; extraction times: two times; solid to liquid ratio: 1 ∶ 20; extraction rate of total flavonoids:4. 55%. [Conclusions] The central composite design-response surface methodology( CCD-RSM) is simple,convenient,and feasible for extraction of total flavonoids from Akebia trifoliata( Thunb.) Koidz.,and the prediction results are reliable.

Bamboo Fiber Modified Asphalt Mixture Proportion Design and Road Performances Based on Response Surface Method

In order to comprehensively utilize the remaining bamboo residue of bamboo products,this paper presents a research on recycling the bamboo fibers from bamboo residue for improving the performance of the asphalt mixtures.First of all,the basic performance parameters of sinocalamus affinis fiber,phyllostachys pubescens fiber,green bamboo fiber were tested and analyzed,and the optimal content and length were put forward.Then,the mix ratio design of the bamboo fiber modified asphalt mixture was further designed through the response surface method,and was verified the rationality of the mix ratio.Finally,the mixture specimens were made according to the experimental design mix ratio,and the high temperature,low temperature performance and moisture susceptibility of the bamboo fiber modified mixtures asphalt were tested.The results showed that the high temperature performance,low temperature performance and moisture susceptibility of bamboo fiber modified asphalt mixtures were improved compared with the performance of SBS modified asphalt mixture.When the length of bamboo fiber is 7.25 mm and the content of 0.22%,the road performance of the asphalt mixture was optimal.Consequentially,the decomposition of bamboo residue into bamboo fiber and its application in asphalt pavement can improve the reuse of bamboo waste,with remarkable environmental benefits and great promotion value.

Improvement of xylanase production by Aspergillus niger XY-1 using response surface methodology for optimizing the medium composition

Objective: To study the optimal medium composition for xylanase production by Aspergillus niger XY-1 in solid-state fermentation (SSF). Methods: Statistical methodology including the Plackett-Burman design (PBD) and the central composite design (CCD) was employed to investigate the individual crucial component of the medium that significantly affected the enzyme yield. Results: Firstly, NaNO3, yeast extract, urea, Na2CO3, MgSO4, peptone and (NH4)2SO4 were screened as the significant factors positively affecting the xylanase production by PBD. Secondly, by valuating the nitrogen sources effect, urea was proved to be the most effective and economic nitrogen source for xylanase production and used for further optimization. Finally, the CCD and response surface methodology (RSM) were applied to determine the optimal concentration of each sig-nificant variable, which included urea, Na2CO3 and MgSO4. Subsequently a second-order polynomial was determined by multiple regression analysis. The optimum values of the critical components for maximum xylanase production were obtained as follows: x1 (urea)=0.163 (41.63 g/L), x2 (Na2CO3)=?1.68 (2.64 g/L), x3 (MgSO4)=1.338 (10.68 g/L) and the predicted xylanase value was 14374.6 U/g dry substrate. Using the optimized condition, xylanase production by Aspergillus niger XY-1 after 48 h fermentation reached 14637 U/g dry substrate with wheat bran in the shake flask. Conclusion: By using PBD and CCD, we obtained the optimal composition for xylanase production by Aspergillus niger XY-1 in SSF, and the results of no additional expensive medium and shortened fermentation time for higher xylanase production show the potential for industrial utilization.

Optimal design of butterfly-shaped linear ultrasonic motor using finite element method and response surface methodology

A new method for optimizing a butterfly-shaped linear ultrasonic motor was proposed to maximize its mechanical output. The finite element analysis technology and response surface methodology were combined together to realize the optimal design of the butterfly-shaped linear ultrasonic motor. First, the operation principle of the motor was introduced. Second, the finite element parameterized model of the stator of the motor was built using ANSYS parametric design language and some structure parameters of the stator were selected as design variables. Third, the sample points were selected in design variable space using latin hypercube Design. Through modal analysis and harmonic response analysis of the stator based on these sample points, the target responses were obtained. These sample points and response values were combined together to build a response surface model. Finally, the simplex method was used to find the optimal solution. The experimental results showed that many aspects of the design requirements of the butterfly-shaped linear ultrasonic motor have been fulfilled. The prototype motor fabricated based on the optimal design result exhibited considerably high dynamic performance, such as no-load speed of 873 mm/s, maximal thrust of 27.5 N, maximal efficiency of 43%, and thrust-weight ratio of 45.8.

Reliability-based design optimization for flexible mechanism with particle swarm optimization and advanced extremum response surface method

To improve the computational efficiency of the reliability-based design optimization(RBDO) of flexible mechanism, particle swarm optimization-advanced extremum response surface method(PSO-AERSM) was proposed by integrating particle swarm optimization(PSO) algorithm and advanced extremum response surface method(AERSM). Firstly, the AERSM was developed and its mathematical model was established based on artificial neural network, and the PSO algorithm was investigated. And then the RBDO model of flexible mechanism was presented based on AERSM and PSO. Finally, regarding cross-sectional area as design variable, the reliability optimization of flexible mechanism was implemented subject to reliability degree and uncertainties based on the proposed approach. The optimization results show that the cross-section sizes obviously reduce by 22.96 mm^2 while keeping reliability degree. Through the comparison of methods, it is demonstrated that the AERSM holds high computational efficiency while keeping computational precision for the RBDO of flexible mechanism, and PSO algorithm minimizes the response of the objective function. The efforts of this work provide a useful sight for the reliability optimization of flexible mechanism, and enrich and develop the reliability theory as well.

EFFECTS OF REACTION AND PROCESSING PARAMETERS ON ETHYLENE POLYMERIZATION USING DIFFERENT ZIEGLER-NATTA CATALYSTS:EMPLOYMENT OF TAGUCHI EXPERIMENTAL DESIGN AND RESPONSE SURFACE METHOD

Different Ziegler-Natta catalysts were employed to polymerize ethylene. To investigate the influences of reaction parameters, namely Al/Ti molar ratio, hydrogen and processing parameters, i.e. ethylene pressure and temperature, a Taguchi experimental design was worked out. An L27 orthogonal array was chosen to take the above-mentioned parameters and relevant interactions into account. Response surface method was the tool used to analyze the experimental design results. Al/Ti, ethylene pressure and temperature were selected as experimental design factors, and catalyst activity and polymerization yield were the response parameters. Increasing pressure, due to an increment in monomer accessibility, and rising Al/Ti, because of higher reduction in the catalysts, cause an increase in both polymerization yield and catalyst activity. Nonetheless, a higher temperature, thanks to reducing ethylene solubility in the slurry medium and partially catalyst destruction, lead to a reduction in both response parameters. A synergistic effect was also observed between temperature and pressure. All catalyst activities will reduce in the presence of hydrogen. Molecular weight also shows a decline in the presence of hydrogen as a transfer agent. However, the polydispersity index remains approximately intact. Using SEM, various morphologies, owing to different catalyst morphologies, were seen for the polyethylene.

Ship Appearance Optimal Design on RCS Reduction Using Response Surface Method and Genetic Algorithms

Radar cross section (RCS) reduction technologies are very important in survivability of the military naval vessels. Ship appearance shaping as an effective countermeasure of RCS reduction redirects the scattered energy from one angular region of interest in space to another region of little interest. To decrease the scattering electromagnetic signals from ship scientifically, optimization methods should be introduced in shaping design. Based on the assumption of the characteristic section design method, mathematical formulations for optimal shaping design were established. Because of the computation-intensive analysis and singularity in shaping optimization, the response surface method (RSM) combined genetic algorithm (GA) was proposed. The poly-nomial response surface method was adopted in model approximation. Then genetic algorithms were employed to solve the surrogate optimization problem. By comparison RCS of the conventional and the optimal design, the superiority and effectiveness of proposed design methodology were verified.

Optimization of medium components using response surface methodology (RSM) for mycelium biomass and exopolysaccharide production by <i>Lentinus squarrosulus</i>

The interaction between sucrose, yeast extract and initial pH was investigated to optimize critical medium components for mycelium biomass and production of exopolysaccharide (EPS) of Lentinus squarrosulus using Response Surface Methodology (RSM). A central composite design (CCD) was applied and a polynomial regression model with quadratic term was used to analyse the experimental data using analysis of variance (ANOVA). ANOVA analysis showed that the model was very significant (p Lentinus squarrosulus are as follows: sucrose concentration 114.61 g/L, yeast extract 1.62 g/L and initial pH of 5.81;sucrose concentration 115.8 g/L, yeast extract of 3.39 g/L and initial pH of 6.44 respectively.

Enhacement of the Viability of <i>Lactobacillus</i><i>plantarum</i>during the Preservation and Storage Process Based on the Response Surface Methodology

Objective: The Response Surface Methodology (RSM) is a commonly used system to optimize cell viability of probiotic strains when they are subjected to different preservation and storage processes. Methods and Results: To determine the optimal levels of incorporation of several cry oprotectants (skim milk, sucrose and trehalose) in the freeze-drying process of Lactobacillus plantarum, a range of experiments based on a Rotational Central Composite design (CCD) were conducted. The results were adjusted to a quadratic model, resulting in the presence of interaction between the different variables. Solving a regression equation, we obtained the optimum concentrations of cryoprotective agents: 24.06% milk powder, 6.22% sucrose, 5.63% trehalose. To visualize the interactions between the three variables involved in the study, Design Expert? software was used. Conclusions: The analysis reveals that while trehalose has a direct effect on the viability of L. plantarum, skim milk and sucrose exert quadratic effects. There are also interactions between cryoprotectants, which emphasize the synergies produced between milk and sucrose and between sucrose and trehalose, which allows maintaining the viability of L. plantarum. Significance and Impact of the Study: The addition of new oligosaccharides as trehalose in premixtures for functional feed can maintain the viability of L. plantarum during longer periods of time, ensuring the proper administration of probiotics to their destinations.

Influence of Operating Parameters on Unbalance in Rotating Machinery Using Response Surface Method

Wide range of rotating machinery contains an inherent amount of unbalance which leads to increase in the vibration level and related faults.In this work,the effect of different operating conditions viz.the unbalanced weight,radius,speed and position of the rotor disc on the unbalance in rotating machine are studied experimentally and analyzed by using Response Surface Methodology(RSM).RSM is a technique which consists of mathematical and statistical methods to develop the relationship between the inputs and outputs of a system by distinct functions.L27 Orthogonal Array(OA)was developed by using Design of Experiments(DOE)according to which experimentation has been carried out.Three accelerometer sensors were mounted to record the vibration responses(accelerations)in radially vertical,horizontal and axial directions.The responses recorded as root mean square values are then analysed using RSM.The relationship between response and operating factors has been established by developing a second order,non-linear mathematical model.Analysis of variance(ANOVA)has been performed for verification of the developed mathematical models.Results obtained from the analysis show that the unbalance weight and speed are most significant operating conditions that contribute the most to the effect the unbalance has on the rotating spindle.

Optimization of Dielectric Barrier Discharge Process for Decolorization of Reactive Blue 19 by Means of Response Surface Methodology

The decolorization of reactive blue 19(RB-19)as a model dye from aqueous solutions has been studied by means of the dielectric barrier discharge(DBD)process.The independent parameters of input power,initial dye concentration and initial pH value were evaluated respectively.Experimental data were optimized by means of a 33 factorial design and response surface methodology(RSM).The dye was quickly removed during the treatment,yielding 96.9%of decolorization efficiency under optimized conditions.Therefore,the total organic carbon(TOC)and chemical oxygen demand(CODcr)results indicated that only the chromophore was destroyed rather than completed oxidation.This was confirmed with UV-vis and tertiary butanol assessments during the DBD treatment.

Optimal Evaluation of Coag-Flocculation Factors for Alum-Brewery Effluent System by Response Surface Methodology

This work investigates coag-flocculation optimization treatment of alum-brewery effluent system via response surface methodology (RSM). To minimize suspended and dissolved particles (SDP), experiments were carried out using nephelometric jar test and 23-factorial design with three star-points, six-center-points and two replications. A central composite design, which is the standard design of RSM, was used to evaluate the effects and interactions of three major factors (coagulation pH, coagulant dosage, settling time) on the treatment efficiency. Multivariable quadratic model developed for the response studied indicates the optimum conditions to be 9, 500mg/l and 20minutes for coagulation pH, coagulant dosage and settling time, respectively. At optimum, the SDP was reduced from 10831.490mg/l to 801.451mg/l, representing 92.601% removal efficiency. RSM has demonstrated to be appropriate approach for the optimization of the coag-flocculation process by statistical evaluation.

Box-Behnken response surface method combined with fingerprint to optimize the extraction process of total anthraquinone from Cassia seeds

Objective:The Box-Behnken response surface method combined with fingerprints was used to optimize the extraction process of total anthraquinone from Cassia seeds.Methods:A three-factor,three-level response surface test was conducted based on the single-factor test with comprehensive evaluation as the measurement index.The comprehensive evaluation indexes included the extraction rate of total anthraquinone of Cassia seeds or the equivalent amount of herbs per gram of total anthraquinone of Cassia seeds,the normalized value of peak areas of 5 index components such as aurantio obtusin in the fingerprint of each sample to 16 shared peaks and the similarity of fingerprints(the reference fingerprint was established by the extraction solvent for the determination of Cassia seeds content in the Chinese Pharmacopoeia 2020 edition)with the weights of 0.2,0.5 and 0.3,respectively.Results:The best extraction process was obtained:the liquid-to-material ratio was 20:1(mL·g-1),the extraction solvent was mixture of 60%ethanol-ethyl acetate(2:1),and the extraction time was 15.12 min.The results of five sets of validation experiments showed that the overall evaluation of total anthraquinone of cassia seeds by the best process was 0.528(RSD=0.45%),and the prediction result of response surface method model was 0.531,and the relative error with the prediction result was 0.531.The relative error of the predicted results was 0.56%,and the best extraction process was consistent with the model prediction,and the obtained best process could be used for the extraction of total anthraquinone from Cassia seeds.Conclusion:The Box-Behnken response surface method combined with the fingerprint technique can be used to find the best reaction conditions and examine the interactions among the factors in a comprehensive and accurate manner,which can provide reference for the optimization and evaluation of the extraction process of Chinese medicine.

Analysis of Density of Sintered Iron Powder Component Using the Response Surface Method

The continued growth of ferrous powder metallurgy in automobile and others engineering application is largely de-pendent on the development of higher density materials and improved mechanical properties. Since density is a predominant factor in the performance of powder metallurgy components, it has been primarily considered for the present investigation. An experimental investigation have been undertaken in order to understand the variation of density with respect to the variation of process parameters viz., compaction load, sinter temperature and sintering time. The relation among the various process parameters with density has been observed. A mathematical model has been developed using second order response surface model (RSM) with central composite design (CCD) considering the above mentioned process parameters. The developed mathematical model would help in predicting the variation in density with the change in the level of different parameters influencing the density variation. This model also can be useful for setting of optimum value of the parameters for achieving the target density.

Optimization of the Impeller Geometry for an Automotive Torque Converter Using Response Surface Methodology and Desirability Function

Response surface methodology (RSM) based on desirability function approach (DFA) is applied to obtain an optimal design of the impeller geometry for an automotive torque converter. The relative importance of six design parameters including impeller blade number, blade thickness, bias angle, scroll angle, inlet angle and exit angle is investigated using orthogonal design approach. The impeller inlet angle, exit angle and bias angle are found to exert the greatest influence on the overall performance of a torque converter, with two flow area factors being considered, namely 17% and 20%. Then, RSM together with central composite design (CCD) method is used to in-depth evaluate the interaction effect of the three key parameters on converter performance. The results demonstrate that impeller exit angle has the strongest impact on peak efficiency, with larger angles yielding the most favorable results. The stall torque ratio maximization is attainable with the increase of impeller bias angle and inlet angle together with smaller exit angle. In the end, an optimized design for the impeller geometry is obtained with stall torque ratio and peak efficiency increased by 1.62% and 1.1%, respectively. The new optimization method can be used as a reference for performance enhancement in the design process of impeller geometry for an automotive torque converter.

Parametric Optimization to Minimise the Surface Roughness on the Machining of GFRP Composites

The present investigation focuses on the parametric influence of machining parameters on the surface finish obtained in turning of glass fiber reinforced polymer （GFRP） composites. The experiments were conducted based on Taguchi＇s experimental design technique. Response surface methodology and analysis of variance （ANOVA） were used to evaluate the composite machining process to perform the optimization. The results revealed that the feed rate was main influencing parameter on the surface roughness. The surface roughness increased with increasing the feed rate but decreased with increasing the cutting speed. Among the other parameters, depth of cut was more insensitive. The predicted values and measured values were fairly close to each other, which indicates that the developed model can be effectively used to predict the surface roughness on the machining of GFRP composites with 95% confidence intervals. Using such model could remarkablely save the time and cost.