Investigations of the effects of two typical jet crushing methods on the atomization and dust reduction performance of nozzles

Single-fuid nozzles and dual-fuid nozzles are the two typical jet crushing methods used in spray dust reduction. To distinguish the atomization mechanism of single-fuid and dual-fuid nozzles and improve dust control efciency at the coal mining faces, the atomization characteristics and dust reduction performance of the two nozzles were quantitatively compared. Results of experiments show that, as water supply pressure increased, the atomization angle of the swirl pressure nozzle reaches a maximum of 62° at 6 MPa and then decreases, but its droplet size shows an opposite trend with a minimum of 41.7 μm. The water supply pressure helps to improve the droplet size and the atomization angle of the internal mixing air–liquid nozzle, while the air supply pressure has a suppressive efect for them. When the water supply pressure is 0.2 MPa and the air supply pressure reaches 0.4 MPa, the nozzle obtains the smallest droplet size which is 10% smaller than the swirl pressure nozzle. Combined with the dust reduction experimental results, when the water consumption at the working surface is not limited, using the swirl pressure nozzle will achieve a better dust reduction efect. However, the internal mixing air–liquid nozzle can achieve better and more economical dust reduction performance in working environments where water consumption is limited.

The Optimization Design of the Nozzle Section for theWater Jet Propulsion System Applied in Jet Skis

The performance of a water jet propulsion system is related to the inlet duct,rotor,stator,and nozzle.Generally,the flow inlet design must fit the bottom line of the hull,and the design of the inlet duct is often limited by stern space.The entire section,from the rotor to the nozzle through the stator,must be designed based on system integration in that the individual performance of these three components will influence each other.Particularly,the section from the rotor to the nozzle significantly impacts the performance of a water jet propulsion system.This study focused on nozzle design and established referable analysis results to facilitate subsequent integrated studies on the design parameters regarding nozzle contour.Most existing studies concentrate on discussions on rotor design and the tip leakage flow of rotors or have replaced the existing complex computational domain with a simple flow field.However,research has yet to implement an integrated,optimal design of the section from the rotor to the nozzle.Given the above,our program conducted preliminary research on this system integration design issue,discussed the optimal nozzle for this section in-depth,and proposed design suggestions based on the findings.This program used an existing model as the design case.This study referred to the actual trial data as the design conditions for the proposed model.Unlike prior references’simple flow field form,this study added a jet ski geometry and free surface to the computational domain.After the linear hull shape was considered,the inflow in the inlet duct would be closer to the actual condition.Based on the numerical calculation result,this study recommends that the optimal nozzle outlet area should be 37%of the inlet area and that the nozzle contour should be linear.Furthermore,for the pump head,static pressure had a more significant impact than dynamic pressure.

Jet Characteristics and Optimization of a Cavitation Nozzle for Hydraulic Fracturing Applications

Hydraulic jetting is a form of fracturing that involves using a high-pressure jet of water to create fractures in the reservoir rock with a nozzle serving as the central component of the hydraulic sandblasting perforation tool.In this study,the flow behavior of the nozzle is simulated numerically in the framework of a SST k-ωturbulence model.The results show that the nozzle structure can significantly influence the jet performance and related cavitation effect.Through orthogonal experiments,the nozzle geometric parameters are optimized,and the following configuration is found accordingly:contraction angle 20°,contraction segment length 6 mm,cylindrical segment diameter 6 mm,cylindrical segment length 12 mm,spread segment length 10 mm,and spread angle 55°.

Sensitivity Analysis of Injection Characteristic to Structural Parameters of GDI Injector Nozzle Hole

The nozzle inner-flow characteristic of the“spray G”injector was studied by the computational fluid dynamics(CFD)simulation,and the sensitivity of cycle fuel mass to the conicity and entrance radius of the nozzle hole were analyzed.Results show that the inner conicity of nozzle hole inhibits the development of cavitation phenomena,and increases the injection rate.While the outer conicity of nozzle hole promotes the diffusion of cavita-tion,leading to reductions of the liquid volume fraction of the nozzle outlet and the local flow resistance of the nozzle hole.The sensitivity of cycle fuel mass to inner-cone nozzle hole is stronger than that of the outer-cone noz-zle,especially at the smaller hole conicity.The increase of injection pressure enhances the sensitivity of the injection characteristics to the nozzle hole structure,in which inner-cone nozzle has higher sensitivity coefficient than the outer-cone nozzle hole.However,the increase of injection pressure aggravates the offset of liquid jet to the nozzle axis of the outer-cone nozzle hole.With the increase of the inner conicity of nozzle,the sensitivity of the injection characteristics to the entrance radius of the hole decreases.With the increase of the outer conicity of nozzle hole,the sensitivity of the injection characteristics to the entrance radius of the hole increases.

Verification and Validation of High-Resolution Inviscid and Viscous Conical Nozzle Flows

Capturing elaborated flow structures and phenomena is required for well-solved numerical flows.The finite difference methods allow simple discretization of mesh and model equations.However,they need simpler meshes,e.g.,rectangular.The inverse Lax-Wendroff(ILW)procedure can handle complex geometries for rectangular meshes.High-resolution and high-order methods can capture elaborated flow structures and phenomena.They also have strong mathematical and physical backgrounds,such as positivity-preserving,jump conditions,and wave propagation concepts.We perceive an effort toward direct numerical simulation,for instance,regarding weighted essentially non-oscillatory(WENO)schemes.Thus,we propose to solve a challenging engineering application without turbulence models.We aim to verify and validate recent high-resolution and high-order methods.To check the solver accuracy,we solved vortex and Couette flows.Then,we solved inviscid and viscous nozzle flows for a conical profile.We employed the finite difference method,positivity-preserving Lax-Friedrichs splitting,high-resolution viscous terms discretization,fifth-order multi-resolution WENO,ILW,and third-order strong stability preserving Runge-Kutta.We showed the solver is high-order and captured elaborated flow structures and phenomena.One can see oblique shocks in both nozzle flows.In the viscous flow,we also captured a free-shock separation,recirculation,entrainment region,Mach disk,and the diamond-shaped pattern of nozzle flows.

Multi-Physics Coupled Acoustic-Mechanics Analysis and Synergetic Optimization for a Twin-Fluid Atomization Nozzle

Fine particulate matter produced during the rapid industrialization over the past decades can cause significant harm to human health.Twin-fluid atomization technology is an effective means of controlling fine particulate matter pollution.In this paper,the influences of the main parameters on the droplet size,effective atomization range and sound pressure level(SPL)of a twin-fluid nozzle(TFN)are investigated,and in order to improve the atomization performance,a multi-objective synergetic optimization algorithm is presented.A multi-physics coupled acousticmechanics model based on the discrete phase model(DPM),large eddy simulation(LES)model,and Ffowcs Williams-Hawkings(FW-H)model is established,and the numerical simulation results of the multi-physics coupled acoustic-mechanics method are verified via experimental comparison.Based on the analysis of the multi-physics coupled acoustic-mechanics numerical simulation results,the effects of the water flow on the characteristics of the atomization flow distribution were obtained.A multi-physics coupled acoustic-mechanics numerical simulation result was employed to establish an orthogonal test database,and a multi-objective synergetic optimization algorithm was adopted to optimize the key parameters of the TFN.The optimal parameters are as follows:A gas flow of 0.94 m^(3)/h,water flow of 0.0237 m^(3)/h,orifice diameter of the self-excited vibrating cavity(SVC)of 1.19 mm,SVC orifice depth of 0.53 mm,distance between SVC and the outlet of nozzle of 5.11 mm,and a nozzle outlet diameter of 3.15 mm.The droplet particle size in the atomization flow field was significantly reduced,the spray distance improved by 71.56%,and the SPL data at each corresponding measurement point decreased by an average of 38.96%.The conclusions of this study offer a references for future TFN research.

Effect of Nozzle Inclination Angle on Fuel-Air Mixing and Combustion in a Heavy Fuel Engine

Heavy-fuel engines are widely used in UAVs(Unmanned Autonomous Vehicles)because of their reliability and high-power density.In this study,a combustion model for an in-cylinder direct injection engine has been imple-mented using the AVL FIRE software.The effects of the angle of nozzle inclination on fuel evaporation,mixture distribution,and combustion in the engine cylinder have been systematically studied at 5500 r/min and consider-ing full load cruise conditions.According to the results,as the angle of nozzle inclination increases,the maximum combustion explosion pressure in the cylinderfirst increases and then it decreases.When the angle of nozzle incli-nation is less than 45°,the quality of the mixture in the cylinder and the combustion performance can be improved by increasing the angle.When the angle of nozzle inclination is greater than 45°,however,the mixture unevenness increases slightly with the angle,leading to a deterioration of the combustion performances.When the angle of nozzle inclination is between 35°and 55°,the overall combustion performance of the engine is rela-tively good.When the angle of nozzle inclination is 45°,the combustion chamber’s geometry and the cylinder’s airflow are well matched with the fuel spray,and the mixture quality is the best.Compared with 25°,the peak heat release rate increases by 20%,and the maximum combustion burst pressure increases by 5.5%.

Effect of droplet characteristics on liquid-phase distribution in spray zone of internal mixing air-mist nozzle

In continuous casting production,droplet characteristics are important parameters for evaluating the nozzle atomization quality,and have a significant impact on the secondary cooling effect and the slab quality.In order to study the behavior of atomized droplets after reaching the slab surface and to optimize the spray cooling effect,the influence of droplet diameter and droplet velocity on the migration behavior of droplets in the secondary cooling zone was analyzed by FLUENT software.Results show that the droplets in the spray zone and on the slab surface are mainly concentrated in the center,thus,the liquid volume fraction in the center is higher than that of either side.As the droplet diameter increases,the region of high liquid volume fraction on the slab surface becomes wider,and the liquid phase distribution in the slab width direction becomes uneven.Although increasing the droplet velocity at the nozzle exit has little effect on droplet diffusion in the spray zone,the distribution becomes more uneven due to more liquid reaches the slab surface per unit time.A prediction formula of the maximum water flow rate on the slab surface for specific droplet characteristics was proposed based on dimensionless analysis and validated by simulated data.A nozzle spacing of 210 mm was recommended under the working conditions in this study,which ensures effective coverage of the spray water over the slab surface and enhances the distribution uniformity of water flow rate in the transverse direction.

Research on static characteristic of double redundance double nozzle flapper valve based on AMESim

The feedback spring rod of the armature assembly is cancelled in the double redundance double nozzle flapper valve(DRDNFV),and the difficulty of valve core displacement control is increased.Therefore,this paper intends to study the static characteristic of DRDNFV through the AMESet and AMESim simulation.It is explored under the circumstance of the fixed orifices being clogged and experimentally verified on the test bench.The results show that the pressure gain increases and the flow gain decreases with the increasing clogged degree of the fixed orifices on both sides.The zero bias increases synchronously with the increasing clogged degree of the unilateral fixed orifice.The experimental results are basically consistent with the theoretical curves and the theoretical correctness of the simulation model is effectively verified.The results can provide the theoretical reference for design,debugging,maintenance and fault diagnosis of DRDNFV.

Application of Thermodynamic Database to Corrosion of ZrO_(2) Containing Submerged Entry Nozzle in Steel Continuous Casting Process

The CALPHAD thermodynamic databases are very useful to analyze the complex chemical reactions happening in high temperature material process.The FactSage thermodynamic database can be used to calculate complex phase diagrams and equilibrium phases involving refractories in industrial process.In this study,the FactSage thermodynamic database relevant to ZrO_(2)-based refractories was reviewed and the application of the database to understanding the corrosion of continuous casting nozzle refractories in steelmaking was presented.

Clogging behavior of submerged entry nozzles for Ti-bearing IF steel

The nozzle clogging behavior of Ti-bearing IF steel was studied by metallographic analysis,scanning electron microscopy（SEM）, energy dispersive spectroscopy（EDS）,and X-ray diffraction（XRD）.According to the experimental results,nozzle clogging primarily appears three layers.There are a lot of large-sized iron particles in the inner layer and mainly slag phase in the middle and outer layers.The principal clog constituents of the inner layer are loose alumina cluster inclusions and granular shaped alumina inclusions,containing iron particles. The clog constituents of the middle layer are mainly dendrite alumina inclusions.The primary phases existing in nozzle clogging are FeO·TiO2 and FeO·Al2O3 besidesα-Al2O3 and a-Fe.The FeO·TiO2 phases among the deposits adhere the deposits together firmly enough to lead to the inferior castability of Ti-bearing ultra low carbon steel compared with that of Ti-free low carbon Al-killed steel.

Supersonic swirling characteristics of natural gas in convergent-divergent nozzles

The supersonic nozzle is a new apparatus which can be used to condense and separate water and heavy hydrocarbons from natural gas.The swirling separation of natural gas in the convergent-divergent nozzle was numerically simulated based on a new design which incorporates a central body. Axial distribution of the main parameters of gas flow was investigated,while the basic parameters of gas flow were obtained as functions of radius at the nozzle exit.The effect of the nozzle geometry on the swirling separation was analyzed.The numerical results show that water and heavy hydrocarbons can be condensed and separated from natural gas under the combined effect of the low temperature（-80℃） and the centrifugal field（482,400g,g is the acceleration of gravity）.The gas dynamic parameters are uniformly distributed correspondingly in the radial central region of the channel,for example the distribution range of the static temperature and the centrifugal acceleration are from -80 to -55℃and 220,000g to 500,000g,respectively,which would create good conditions for the cyclone separation of the liquids.However,high gradients of gas dynamic parameters near the channel walls may impair the process of separation.The geometry of the nozzle has a great influence on the separation performance. Increasing the nozzle convergent angle can improve the separation efficiency.The swirling natural gas can be well separated when the divergent angle takes values from 4°to 12°in the convergent-divergent nozzle.

Studies on Aerodynamic Behavior and Performance of Aerospike Nozzles

Experimental and numerical studies are carried out on a 6-cell tile-shaped aerospike nozzle, a 6-cell aerospike nozzle with round-to-rectangle primary nozzles and a 1-cell linear aerospike nozzle. Good altitude compensation capacities and high efficiencies are obtained in the tests. The efficiencies of 6-cell tile-shaped aerospike nozzle and 1-cell linear aerospike nozzle at design altitude approach to 100 %, and that of 6-cell aerospike nozzle with round-to-rectangle primary nozzles in the same condition is about 95 % due to the imperfect cell contour and manufacturing defects. Numerical results are in good agreements with test data. The effects of ambient pressure on exhaust and then on base behavior are analyzed, The effects of variation in the amount of base bleed on performance are also examined in the tests.

Comparative study on the flow fields of three atomization nozzles

In this paper, the flow fields of three types of nozzles （ Hartmann, Laval and Laminar nozzles ） under the same conditions are simulated, and the corresponding to pressure, temperature, velocity and turbulence intensity are obtained. The results suggest that two crushing presents in the atomization process using Hartmann nozzle, but only one crushing presents in the atomization process using the other nozzles, through the comparative research on the flow field features of three types of nozzle. Furthermore, the shockwave plays a more important role in crushing of liquid metal than velocity.

Structure Optimization of SENs and Upper Nozzles

The structure of SEN and upper nozzles was optimized and simulated. Relevant trials were conducted on site during thecasting of Al-killed steel. These optimizations effectively solve the nozzle clogging and reduce the defects of the casting slab.

Experimental study on atomization characteristics and dust-reduction performance of four common types of pressure nozzles in underground coal mines

Pressure nozzle is commonly used in the dust-reduction techniques by spraying of underground coal mines.Based on the internal structure,the pressure nozzle can be divided into the following types:spiral channel nozzle,tangential flow-guided nozzle and X-swirl nozzle.In order to provide better guidance on the selection of nozzles for the coal mine dust-reduction systems by spraying,we designed comparing experiments to study the atomization characteristics and dust-reduction performance of four commonly used nozzles in the coal mine underground with different internal structures.From the experimental results on the atomization characteristics,both the tangential flow-guided nozzle and the X-swirl nozzle have high flow coefficients.The atomization angle is the largest in the spiral non-porous nozzle,and smallest in both the X-swirl nozzle and the spiral porous nozzle.The spraying range and the droplet velocity are inversely proportional to the atomization angle.When the water pressure is low,the atomization performance of the spiral non-porous nozzle is the best among the four types of nozzles.The atomization performance of the X-swirl nozzle is superior to other types when the water pressure is high.Under the high water pressure,the particle size of the atomized droplets is smallest in the X-swirl nozzle.Through the experiments on the dust-reduction performance of the four types of nozzles and the comprehensive analysis,the X-swirl nozzle is recommended for the coal mine application site with low water pressure in the dust-reduction system,while at the sites with high water pressure,the spiral non-porous nozzle is recommended,which has the lowest water consumption and obvious economic advantages.

Reaction thrust of water jet for conical nozzles

Clear knowledge on the reaction thrust of water jet is valuable for better design of water jet propulsion system. In this paper, theoretical, numerical and experimental studies were carried out to investigate the effects of the nozzle geometry as-well as the inlet conditions on the reaction thrust of water jet. Comparison analyses reveal that the reaction thrust has a direct proportional relationship with the product of the inlet pressure, the square of flow rate and two-thirds power exponent of the input power. The results also indicate that the diameter of the cylinder column for the conical nozzle has great influence on the reaction thrust characteristics. In addition, the best values of the half cone angle and the cylinder column length exist to make the reaction thrust reach its maximum under the same inlet conditions.

A Laboratory Investigation into the Fuel Atomization Process in a Diesel Engine for Different Configurations of the Injector Nozzles and Flow Conditions

This paper reports a laboratory investigation of the fuel injection process in a diesel engine.The atomization process of the considered fuel(a hydrocarbon liquid)and the ensuing mixing with air is studied experimentally under high-pressure conditions.Different types of injector nozzles are examined,including(two)new configurations,which are compared in terms of performances to a standard injector manufactured by the Bosch company.For the two alternate configurations,the intake edges of one atomizing hole(hole No.1)are located in the sack volume while for the other(hole No.2)they are located on the locking cone of the needle valve.The injection process,the fuel atomization fineness and fuel supply speed characteristics are studied as functions of high-pressure fuel pump camshaft speed and rotation angle.The results obtained show that a decrease in the high-pressure fuel pump camshaft speed can produce fuel redistribution depending on the injector operation.In general,however,the hole No.1 can ensure fuel flow with higher speed with respect to the hole No.2 for all the operation modes of the injector.Based on such an analysis,we conclude that the use of certain injectors can enable a fine tuning of the propagation process of fuel sprays into various areas of the diesel engine combustion chamber.

TRANSONIC SHOCK SOLUTIONS TO THE EULER SYSTEM IN DIVERGENT-CONVERGENT NOZZLES

In this paper,we study the transonic shock solutions to the steady Euler system in a quasi-one-dimensional divergent-convergent nozzle.For a given physical supersonic inflow at the entrance,we obtain exactly two non-isentropic transonic shock solutions for the exit pressure lying in a suitable range.In addition,we establish the monotonicity between the location of the transonic shock and the pressure downstream.

Effects of atomization parameters of dust removal nozzles on the de-dusting results for different dust sources

In order to obtain appropriate spray pressure and enhance the spraying and dust removal efficiency, various factors including the dust characteristics, nozzle spraying angle, effective spraying range, water consumption and droplet size are taken into account. The dust characteristics from different mines and atomization parameters of different pressure nozzles were measured. It was found that the internal pressure of coal cutters and roadheaders should be kept at 2 MPa, which could ensure large droplet size, large spraying angle and low water consumption and hence realizing a large-area covering and capture for large particle dusts. However, the external spray pressure should be kept at 4 MPa for smaller droplet size and longer effective spraying range, leading to effective dust removal in the operator zone. The spray pressure of support moving, drawing opening, and stage loader on a fully mechanized caving face and stage loader on a fully mechanized driving face should be kept at 8 MPa, under which the nozzles have long effective spraying range, high water flow and small droplet size for the rapid capture of instantaneous, high-concentration and small size dust groups. From the applications on the caving and driving faces in the coal mines, it is indicated that the optimization of spray pressure in different spraying positions could effectively enhance dust removal efficiency. Selecting appropriate nozzles according to the dust characteristics at different positions is also favorable for dust removal efficiency. With the selected nozzles under optimal pressures, the removal rates of both total dust and respirable dust could reach over70%, showing a significant de-dusting effect.