Discovery and inspiration of large-and medium-sized glutenite-rich oil and gas fields in the eastern South China Sea:An example from Paleogene Enping Formation in Huizhou 26 subsag,Pearl River Mouth Basin

Based on the practice of oil and gas exploration in the Huizhou Sag of the Pearl River Mouth Basin,the geochemical indexes of source rocks were measured,the reservoir development morphology was restored,the rocks and minerals were characterized microscopically,the measured trap sealing indexes were compared,the biomarker compounds of crude oil were extracted,the genesis of condensate gas was identified,and the reservoir-forming conditions were examined.On this basis,the Paleogene Enping Formation in the Huizhou 26 subsag was systematically analyzed for the potential of oil and gas resources,the development characteristics of large-scale high-quality conglomerate reservoirs,the trapping effectiveness of faults,the hydrocarbon migration and accumulation model,and the formation conditions and exploration targets of large-and medium-sized glutenite-rich oil and gas fields.The research results were obtained in four aspects.First,the Paleogene Wenchang Formation in the Huizhou 26 subsag develops extensive and thick high-quality source rocks of semi-deep to deep lacustrine subfacies,which have typical hydrocarbon expulsion characteristics of"great oil generation in the early stage and huge gas expulsion in the late stage",providing a sufficient material basis for hydrocarbon accumulation in the Enping Formation.Second,under the joint control of the steep slope zone and transition zone of the fault within the sag,the large-scale near-source glutenite reservoirs are highly heterogeneous,with the development scale dominated hierarchically by three factors(favorable facies zone,particle component,and microfracture).The(subaqueous)distributary channels near the fault system,with equal grains,a low mud content(<5%),and a high content of feldspar composition,are conducive to the development of sweet spot reservoirs.Third,the strike-slip pressurization trap covered by stable lake flooding mudstone is a necessary condition for oil and gas preservation,and the NE and nearly EW faults obliquely to the principal stress have the best control on traps.Fourth,the spatiotemporal configuration of high-quality source rocks,fault transport/sealing,and glutenite reservoirs controls the degree of hydrocarbon enrichment.From top to bottom,three hydrocarbon accumulation units,i.e.low-fill zone,transition zone,and high-fill zone,are recognized.The main area of the channel in the nearly pressurized source-connecting fault zone is favorable for large-scale hydrocarbon enrichment.The research results suggest a new direction for the exploration of large-scale glutenite-rich reservoirs in the Enping Formation of the Pearl River Mouth Basin,and present a major breakthrough in oil and gas exploration.

Stress corrosion cracking behavior of buried oil and gas pipeline steel under the coexistence of magnetic field and sulfate-reducing bacteria

Magnetic field and microorganisms are important factors influencing the stress corrosion cracking(SCC)of buried oil and gas pipelines. Once SCC occurs in buried pipelines, it will cause serious hazards to the soil environment. The SCC behavior of X80 pipeline steel under the magnetic field and sulfate-reducing bacteria(SRB) environment was investigated by immersion tests, electrochemical tests, and slow strain rate tensile(SSRT) tests. The results showed that the corrosion and SCC sensitivity of X80 steel decreased with increasing the magnetic field strength in the sterile environment. The SCC sensitivity was higher in the biotic environment inoculated with SRB, but it also decreased with increasing magnetic field strength, which was due to the magnetic field reduces microbial activity and promotes the formation of dense film layer. This work provided theoretical guidance on the prevention of SCC in pipeline steel under magnetic field and SRB coexistence.

Sedimentary build-ups of pre-salt isolated carbonate platforms and formation of deep-water giant oil fields in Santos Basin,Brazil

In response to the problems of unclear distribution of deep-water pre-salt carbonate reservoirs and formation conditions of large oil fields in the Santos passive continental margin basin,based on comprehensive utilization of geological,seismic,and core data,and reconstruction of Early Cretaceous prototype basin and lithofacies paleogeography,it is proposed for the first time that the construction of pre-salt carbonate build-ups was controlled by two types of isolated platforms:inter-depression fault-uplift and intra-depression fault-high.The inter-depression fault-uplift isolated platforms are distributed on the present-day pre-salt uplifted zones between depressions,and are built on half-and fault-horst blocks that were inherited and developed in the early intra-continental and inter-continental rift stages.The late intra-continental rift coquinas of the ITP Formation and the early inter-continental rift microbial limestones of the BVE Formation are continuously constructed;intra-depression fault-high isolated platforms are distributed in the current pre-salt depression zones,built on the uplifted zones formed by volcanic rock build-ups in the early prototype stage of intra-continental rifts,and only the BVE microbial limestones are developed.Both types of limestones formed into mound-shoal bodies,that have the characteristics of large reservoir thickness and good physical properties.Based on the dissection of large pre-salt oil fields discovered in the Santos Basin,it has been found that both types of platforms could form large-scale combined structural-stratigraphic traps,surrounded by high-quality lacustrine and lagoon source rocks at the periphery,and efficiently sealed by thick high-quality evaporite rocks above,forming the optimal combination of source,reservoir and cap in the form of“lower generation,middle storage,and upper cap”,with a high degree of oil and gas enrichment.It has been found that the large oil fields are all bottom water massive oil fields with a unified pressure system,and they are all filled to the spill-point.The future exploration is recommended to focus on the inter-depression fault-uplift isolated platforms in the western uplift zone and the southern section of eastern uplift zones,as well as intra-depression fault-high isolated platforms in the central depression zone.The result not only provides an important basis for the advanced selection of potential play fairways,bidding of new blocks,and deployment of awarded exploration blocks in the Santos Basin,but also provides a reference for the global selection of deep-water exploration blocks in passive continental margin basins.

Improving Crude Oil Flow Using Graphene Flakes under an Applied Electric Field

Graphene flakes(GF)have been prepared and assessed as a material for improving flow in oil pipelines under the effect of an electric field.In particular,different amounts of GFs have been considered in order to determine the optimal flow conditions.The GFs were prepared from graphite foam,derived from the dehydration of sugar with a particle size of 500-600μm,which was dispersed in ethanol and exfoliated in a ball mill under a shear force.After 15 h of exfoliation,sonication,and subsequent high-speed centrifugation at 3000 rpm,irregular-shaped GFs of 50-140 nm were produced and characterized using scanning electron microscopy,X-ray diffractometry,atomic force microscopy,and Raman spectroscopy.The prepared graphene sheets have been found to display excellent morphology and good graphitic structure.Experiments on flow improvement were conducted using the central composite rotatable design method for three parameters:stimulation time(15,30,45,and 60 s),applied voltage(150,170,200,and 220 V),and concentration of the GFs(0,100,200,and 400 mg/L).The optimal conditions for improved crude oil flow were then determined using the STATISTICA and WinQSB software packages.The results have confirmed the effectiveness of the use of the prepared GFs as a flow improver for crude oil,where the flow improvement is essentially a result of a reduction in viscosity and suppression of friction in the crude oil system.

Application of Fluid Phase Recovery Method in the Early Development of BZ26-6 Volatile Oil Field in Bohai Sea

BZ26-6 Oilfield is a kind of deep metamorphic rock buried-hill volatile oilfield in Bohai Sea, China. Its early development plan is restricted due to the simultaneous production of oil and gas in large sections of reservoirs, unclear understanding of formation fluid properties and uncertainty of gas-oil interface. Through theoretical research on phase recovery and experimental analysis of crude oil phase characteristics in the original formation, characteristic parameters of the equilibrium condensate gas fluid are restored and calculated. Through the superimposed phase diagram of volatile oil and condensate gas, BZ26-6 Oilfield is determined to be a volatile oil reservoir with a condensate gas cap, with formation pressure and saturation pressure of 36.1 MPa, respectively. Based on the research results of oil-gas phase behavior characteristics, the thermodynamic equations and equation of state are jointly used to solve the problem, and the content change curves of each component at different depths are drawn. Combined with the sensitivity analysis of numerical simulation, the gas-oil interface is determined to be -3726 m above sea level. The fluid phase analysis software, Fluidmodeler, is used to simulate volatile oil degassing and condensate gas separation experiments. In combination with oil and gas production data obtained through the production test, the specific oil recovery index and the specific gas recovery index are determined to be 0.408 m3/(MPa·d·m) and 1195 m3/(MPa·d·m), respectively. And the reasonable production capacity prediction is conducted on the early development of BZ26-6 Oilfield. The research results can provide a theoretical basis for the efficient development of similar complex oil and gas reservoirs.

Optimization of the Algorithm for Increasing Injection Rate in Water Injection Wells for Pressure Optimization in P Oilfield

In today’s society, with the continuous growth of energy demand, Bohai Oilfield, as an important offshore oil resource base in China, is facing increasingly severe challenges while contributing to national energy security. In order to improve the quality of water injection in the oilfield and gradually achieve efficient and stable production, Bohai Oilfield has launched a water injection well pressure optimization project, focusing on improving the efficiency and quality of water injection in the water injection wells, in order to achieve the optimal water injection plan. In practical work, P Oilfield continues to promote the development of water injection well pressure optimization projects, emphasizing practical exploration and continuous optimization of work plans. However, during the project implementation process, there were some problems, one of which was that the statistics of cumulative injection volume were not scientific enough, resulting in a more comprehensive and accurate presentation of the actual results of pressure optimization work. In the context of continuous improvement work, after careful analysis and research, P Oilfield has decided to optimize the cumulative injection rate algorithm to guide the oilfield’s water injection work in a more refined way, ensuring sufficient and good water injection, and enhancing the oilfield’s production efficiency and comprehensive competitiveness.

Layered injection technology for chemical flooding of Class-Ⅲ oil reservoirs in the Daqing Oil Fields complex,Songliao Basin,Northeast China

The Class-Ⅲ oil reservoirs of Lasaxing oilfield in the Daqing Oil Fields complex have geological oil reserves of 1.86 billion tonnes,an oil recovery of 39%,with remaining reserves accounting for more than 45%of the total geological reserves of the oilfield.Therefore,they have considerable potential for future oil production.The current layered injection technologies fail to achieve effective control over the low single-layer injection rates since they can only produce low throttle differential pressure under low injection rates(5-20 m^(3)/d).In this study,a symmetrically-structured double-offset-hole injection allocator and a novel throttling component were developed.Their spatial layout was constructed and mechanical parameters were optimized using finite element analysis,which allows for expanding the flow rate range at low injection rates.According to experimental results,the throttle differential pressure increased from 0.2 MPa to 0.8 MPa at an injection rate of 5 m^(3)/d,and the range of the single-layer flow rates expanded from 20-70 m^(3)/d to 5-70 m3/d.The field test results show that the effective production of oil layers with medium and low permeability was achieved and that the ratio of producing oil layer thickness to the total reservoir thickness increased by 9.7%on average.Therefore,this study provides valuable technical support for the effective chemical-flooding-based development of Class-Ⅲ oil reservoirs.

Shale oil recovery by CO_(2)injection in Jiyang Depression,Bohai Bay Basin,East China

Laboratory experiments,numerical simulations and fracturing technology were combined to address the problems in shale oil recovery by CO_(2)injection.The laboratory experiments were conducted to investigate the displacement mechanisms of shale oil extraction by CO_(2)injection,and the influences of CO_(2)pre-pad on shale mechanical properties.Numerical simulations were performed about influences of CO_(2)pre-pad fracturing and puff-n-huff for energy replenishment on the recovery efficiency.The findings obtained were applied to the field tests of CO_(2)pre-pad fracturing and single well puff-n-huff.The results show that the efficiency of CO_(2)puff-n-huff is affected by micro-and nano-scale effect,kerogen,adsorbed oil and so on,and a longer soaking time in a reasonable range leads to a higher exploitation degree of shale oil.In the"injection+soaking"stage,the exploitation degree of heavy hydrocarbons is enhanced by CO_(2)through its effects of solubility-diffusion and mass-transfer.In the"huff"stage,crude oil in large pores is displaced by CO_(2)to surrounding larger pores or bedding fractures and finally flows to the production well.The injection of CO_(2)pre-pad is conducive to keeping the rock brittle and reducing the fracture breakdown pressure,and the CO_(2)is liable to filter along the bedding surface,thereby creating a more complex fracture.Increasing the volume of CO_(2)pre-pad can improve the energizing effect,and enhance the replenishment of formation energy.Moreover,the oil recovery is more enhanced by CO_(2)huff-n-puff with the lower shale matrix permeability,the lower formation pressure,and the larger heavy hydrocarbon content.The field tests demonstrate a good performance with the pressure maintained well after CO_(2)pre-pad fracturing,the formation energy replenished effectively after CO_(2)huff-n-puff in a single well,and the well productivity improved.

Fault diagnosis and analysis of main sea water pump based on vibration monitoring in offshore oil field

The main sea water pump is the key equipment for the floating production storage and offloading （FPSO）. Affected by some factors such as hull deformation, sea water corrosion, rigid base and pipeline stress, the vibration value of main sea water pump in the horizontal direction is abnormally high and malfunctions usually happen. Therefore, it is essential to make fault diagnosis of main sea water pump, By conventional off-line monitoring and vibration amplitude spectrum analysis, the fault cycle is found and the alarm value and stop value of equipment are set, which is helpful to equipment maintenance and accident prevention.

Donghe Sandstone Subtle Reservoir Exploration and Development Technology in Hade 4 Oilfield

Hade 4 oilfield is located on the Hadexun tectonic belt north of the Manjiaer depression in the Tarim basin, whose main target layer is the Donghe sandstone reservoir, with a burial depth over 5,000m and an amplitude below 34m, at the bottom of the Carboniferous. The Donghe sandstone reservoir consists of littoral facies deposited quartz sandstones of the transgressive system tract, overlapping northward and pinching out. Exploration and development confirms that water-oil contact tilts from the southeast to the northwest with a drop height of nearly 80m. The reservoir, under the control of both the stratigraphic overlap pinch-out and tectonism, is a typical subtle reservoir. The Donghe sandstone reservoir in Hade 4 oilfield also has the feature of a large oil-bearing area (over 130 km2 proved), a small thickness (average efficient thickness below 6m) and a low abundance (below 50 × 104t/km2). Moreover, above the target layer developed a set of igneous rocks with an uneven thickness in the Permian formation, thus causing a great difficulty in research of the velocity field. Considering these features, an combination mode of exploration and development is adopted, namely by way of whole deployment, step-by-step enforcement and rolling development with key problems to be tackled, in order to further deepen the understanding and enlarge the fruits of exploration and development. The paper technically focuses its study on the following four aspects concerning problem tackling. First, to strengthen the collecting, processing and explanation of seismic data, improve the resolution, accurately recognize the pinch-out line of the Donghe sandstone reservoir by combining the drilling materials in order to make sure its distribution law; second, to strengthen the research on velocity field, improve the accuracy of variable speed mapping, make corrections by the data from newly- drilled key wells and, as a result, the precision of tectonic description is greatly improved; third, to strengthen the research on sequence stratigraphy and make sure the distribution law of the Donghe sandstone; and fourth, with a step- by-step extrapolation method, to deepen the cognition of the leaning water-oil contact, and by combining the tectonic description and drilling results, to make sure little by little the law of change of the water-oil contact. The exploration and development of the Donghe sandstone subtle reservoir in Hade 4 oilfield is a gradually perfected process. From 1998 when it was discovered till now, the reservoir has managed to make a benign circle of exploration and development, in which its reserve has gradually been enlarged, its production scale increased, and, in a word, it has used techniques necessary for this subtle reservoir in the Tarim basin.

Daily Variation of Natural Emission of Methane to the Atmosphere and Source Identification in the Luntai Fault Region of the Yakela Condensed Oil/Gas Field in the Tarim Basin,Xinjiang,China

The static flux chamber method was applied to study natural emissions of methane to the atmosphere in the Luntai fault region of Yakela Condensed Oil/Gas Field in the Tarim Basin, Xinjiang Municipality, northwestern China. Using an online method, which couples together a gas chromatography/high-temperature conversion/isotope ratio mass spectrometry （GC/C/MS）, 13^C/12^C ratios of methane in flux chambers were measured and showed that methane gases are liable to migrate from deep oil/gas reservoirs to the surface through fault regions and that a part of the migrated methane, which remains unoxidized can be emitted into the atmosphere. Methane emission rates were found to be highest in the mornings, lowest in the afternoons and then increase gradually in the evenings. Methane emission rates varied dramatically in different locations in the fault region. The highest methane emission rate was 10.96 mg/m^2·d, the lowest 4.38 mg/m^2, and the average 7.55 mg/ m^2·d. The 13^C/12^C ratios of the methane in the flux chambers became heavier as the enclosed methane concentrations increased gradually, which reveals that methane released from the fault region might come from thermogenic methane of the deep condensed oil/gas reservoir.

Kinetic Performance of Oil-field Produced Water Treatment by Biological Aerated Filter

The biological aerated filter （BAF） was used to treat the oil-field produced water. The removal efficiency for oil, COD, BOD and suspended solids （SS） was 76.3%-80.3%, 31.6%-57.9%, 8.6.3%-96.3% and76.4%--82.7%, respectively when the hydraulic loading rates varied from 016m·h^-1 to 1.4m·h^-1. The greatest partof removal, for example more than 80% of COD removal, occurred on the top 100cm of the media in BAF. The kinetic .performance of BAF indicated that the relationship of BOD removal efficiency with the hydraulic loadingrates, in biological aerated filters could be described by c1/c1=l-exp（-2.44/L^0.59）. This equation could be used topredict the B OD.removal efficiency at different hydraulic loading rates.

Geological emission of methane from the Yakela condensed oil/gas field in Talimu Basin, Xinjiang, China

A static flux chamber method was applied to study natural emissions of methane into the atmosphere in the Yakela condensed oil/gas field in Talimu Basin, Xinjiang, China. Using an online method, which couples a gas chromatography/high-temperature conversion/isotope ratio mass spectrometry (GC/C/MS) together, the 13C/12C ratios of methane in the flux chambers were measured. The results demonstrated that methane gases were liable to migrate from deep oil/gas reservoir to the surface through microseepage and p...

Formation and distribution characteristics of Proterozoic–Lower Paleozoic marine giant oil and gas fields worldwide

There are rich oil and gas resources in marine carbonate strata worldwide.Although most of the oil and gas reserves discovered so far are mainly distributed in Mesozoic,Cenozoic,and upper Paleozoic strata,oil and gas exploration in the Proterozoic–Lower Paleozoic（PLP）strata—the oldest marine strata—has been very limited.To more clearly understand the oil and gas formation conditions and distributions in the PLP marine carbonate strata,we analyzed and characterized the petroleum geological conditions,oil and gas reservoir types,and their distributions in thirteen giant oil and gas fields worldwide.This study reveals the main factors controlling their formation and distribution.Our analyses show that the source rocks for these giant oil and gas fields are mainly shale with a great abundance of type I–II organic matter and a high thermal evolution extent.The reservoirs are mainly gas reservoirs,and the reservoir rocks are dominated by dolomite.The reservoir types are mainly karst and reef–shoal bodies with well-developed dissolved pores and cavities,intercrystalline pores,and fractures.These reservoirs arehighly heterogeneous.The burial depth of the reservoirs is highly variable and somewhat negatively correlated to the porosity.The cap rocks are mainly thick evaporites and shales,with the thickness of the cap rocks positively correlated to the oil and gas reserves.The development of high-quality evaporite cap rock is highly favorable for oil and gas preservation.We identified four hydrocarbon generation models,and that the major source rocks have undergone a long period of burial and thermal evolution and are characterized by early and long periods of hydrocarbon generation.These giant oil and gas fields have diverse types of reservoirs and are mainly distributed in paleo-uplifts,slope zones,and platform margin reef-shoal bodies.The main factors that control their formation and distribution were identified,enabling the prediction of new favorable areas for oil and gas exploration.

Effect of HCO_3^- concentration on CO_2 corrosion in oil and gas fields

The effect of HCO3^- concentration on CO2 corrosion was investigated by polarization measurement of potentiodynamic scans and weight-loss method, Under the conditions of high pressure and high temperature, the corrosion rate of steel X65 decreased with the increase of HCO3^- concentration, while pH of solution increased. SEM, EDS, and XRD results of the corrosion scales indir cated that the typical FeCO3 crystallite was found at low HCO3^- concentration but Ca（Fe,Mg）（CO3）2 was found at high HCO3^- con- centration. Ca^2＋ and Mg^2＋ are precipitated preferential to Fe^2＋ at high pH value. Potentiodynamic polarization curves showed that the cathodic current density decreases with the increase of HCO3^- concentration at low HCO3^- concentration. When the HCO3^- concentration reaches 0.126 mol/L, increasing HCO3^- concentration promotes cathodic reactions. Anodic behavior is an active process at low HCO3^- concentration and the anodic current density decreases with the increase of HCO3^- concentration. An evident active-passive behavior is exhibited in anodic process at 0.126 mol/L HCO3^-.

Investigation of the oil-seawater mixed flow under an electromagnetic field

The electromagnetic separation method is a new approach to treat ship-based marine oily wastewater,in which oil droplets are dispersed in seawater(oil-seawater mixed flow).In order to clarify the separation process and determine the separation characteristics,the flow field and volume fraction of the oil droplets of the oil-seawater mixed flow under an applied electromagnetic field with different operating conditions were investigated by 2D numerical simulations with the Eulerian model.The results show that:(1)the downward Lorentz force causes seawater to flow downwards and the oil droplets to move upwards due to the electromagnetic separation force in the effective section of the separation channel;(2)the volume fraction of the oil droplets at the top of the outlet section increases with the current density,magnetic field,and the diameter of the oil droplet and decreases with the inlet velocity of the oily seawater.The results provide useful guidance for the design of electromagnetic separation devices of the oil-seawater mixed flow.

Characteristics of Abnormal Pressure Systems and Their Responses of Fluid in Huatugou Oil Field,Qaidam Basin

Based on the comprehensive study of core samples, well testing data, and reservoir fluid properties, the construction and the distribution of the abnormal pressure systems of the Huatugou oil field in Qaidam Basin are discussed. The correlation between the pressure systems and hydrocarbon accumulation is addressed by analyzing the corresponding fluid characteristics. The results show that the Huatugou oil field as a whole has low formation pressure and low fluid energy; therefore, the hydrocarbons are hard to migrate, which facilitates the forming of primary reservoirs. The study reservoirs, located at the Xiayoushashan Formation （N1/2） and the Shangganchaigou Formation （N1） are relatively shallow and have medium porosity and low permeability. They are abnormal low-pressure reservoirs with an average formation pressure coefficient of 0.61 and 0.72 respectively. According to the pressure coefficient and geothermal anomaly, the N1 and N1/2 Formations belong to two independent temperature-pressure systems, and the former has slightly higher energy. The low-pressure compartments consist of a distal bar as the main body, prodelta mud as the top boundary, and shore and shallow lake mud or algal mound as the bottom boundary. They are vertically overlapped and horizontally paralleled. The formation water is abundant in the Cl^- ion and can be categorized as CaCl2 type with high safinity, which indicates that the abnormal low-pressure compartments are in good sealing condition and beneficial for oil and gas accumulation and preservation.

Optimization of operation conditions for extracting lithium ions from calcium chloride-type oil field brine

AI（OH）3 was prepared to extract lithium ions from calcium chloride-type oil field brine. The influences of four factors, namely temperature, Al3＋/Li＋ molar ratio, OH-/Al3＋ molar ratio, and contact time between AI（OH）3 and the brine, on the yield of lithium ions were investigated. It is found that their optimal values are 35℃, 4.5, 2.6, and 6 h, respectively. In the course of the experiment, the apparent pH value was observed. The results reveal that the apparent pH value has no remarkable influence on the yield of lithium ions. Meanwhile, the effects of the concentrations of calcium ions and magnesium ions in the brine on lithium recovery were studied. The results indicate that cal- cium ions have minor negative influence on the yield of lithium ions under optimal conditions, and magnesium ions slightly influence the yield of lithium ions.

Synergistic effect of magnetic field and nanocomposite pour point depressant on the yield stress of waxy model oil

Yield stress,as the key parameter to characterize the network strength of waxy oil,is important to the petroleum pipeline safety.Reducing the yield stress of waxy oil is of great significance for flow assurance.In this study,the effect of alternating magnetic field(intensity,frequency)on the yield stress of a waxy model oil with nanocomposite pour point depressant(NPPD)is systematically investigated.An optimum magnetic field intensity and frequency is found for the reduction in yield stress.When adding with NPPD,the heterogeneous nucleation of NPPD contributes to the reduction in yield stress for waxy model oil.Interestingly,the magnetic field is helpful for the modification of yield stress at a lower frequency and intensity before the optimal value;however,the modification is found to be weakened when the magnetic field is further increased after the optimal value.Possible explanation is proposed that the aggregation morphology of wax crystal would be altered and results in the release of wrapped oil phase from the network structure under the magnetic field.