Signal characteristics of coal and rock dynamics with micro-seismic monitoring technique

In this study, differences of signal characteristics between mine shocks and coal and gas outbursts in coal mines were examined with the micro-seismic monitoring technique and time-frequency analysis. The duration of the mine shock is short while the coal and gas outburst lasts longer. The outburst consists of three stages： the pre-shock, secondary shock and main shock stage, respectively. The velocity amplitude of the mine shock is between 10 s and 10-3 m/s, which is higher than that of the outburst with the same energy level. In addition, in both cases, the correlation between the velocity amplitude and energy is positive while the correlation between the signal frequency band distribution and energy is negative. The signal frequency band of the high energy mine shock is distributed between 0 and 50 Hz, and the low energy mine shock is between 50 and 100 Hz. The fractal characteristics of mine shocks were studied based on a fractal theory. The box dimensions of high energy mine shocks are lower than the low energy ones, however, the box dimensions of outbursts are higher than that of mine shocks with the same energy level. The higher box dimensions indicate more dangerous dynamic events.

Leaf stable carbon isotope composition in Picea schrenkiana var. tianschanica in relation to leaf physiological and morphological characteristics along an altitudinal gradient

To understand the effects of leaf physiological and morphological characteristics on δ13C of alpine trees, we examined leaf δ13C value, LA, SD, LNC, LPC, LKC, Chla+b, LDMC, LMA and Narea in one-year-old needles of Picea schrenkiana var. tianschanica at ten points along an altitudinal gradient from 1420 m to 2300 m a.s.l. on the northern slopes of the Tianshan Mountains in northwest China. Our results indicated that all the leaf traits differed significantly among sampling sites along the altitudinal gradient(P<0.001). LA, SD, LPC, LKC increased linearly with increasing elevation, whereas leaf δ13C, LNC, Chla+b, LDMC, LMA and Narea varied non-linearly with changes in altitude. Stepwise multiple regression analyses showed that four controlled physiological and morphological characteristics influenced the variation of δ13C. Among these four controlled factors, LKC was the most profound physiological factor that affected δ13C values, LA was the secondary morphological factor, SD was the third morphological factor, LNC was the last physiological factor. This suggested that leaf δ13C was directly controlled by physiological and morphological adjustments with changing environmental conditions due to the elevation.

Physical and mechanical properties of sandstone containing a single fissure after exposure to high temperatures

In order to investigate the physical and mechanical properties of sandstone containing fissures after exposure to high temperatures,fissures with different angles α were prefabricated in the plate sandstone samples,and the processed samples were then heated at 5 different temperatures.Indoor uniaxial compression was conducted to analyze the change rules of physical properties of sandstone after exposure to high temperature,and the deformation,strength and failure characteristics of sandstone containing fissures.The results show that,with increasing temperature,the volume of sandstone increases gradually while the quality and density decrease gradually,and the color of sandstone remains basically unchanged while the brightness increases markedly when the temperature is higher than 585 ℃;the peak strength of sandstone containing fissures first decreases then increases when the temperature is between 25℃and 400℃.The peak strain of sandstone containing fissures increases gradually while the average modulus decreases gradually with increasing temperature,and the mechanical properties of sandstone show obvious deterioration after 400 ℃.The peak strain of sandstone containing fissures increases gradually while the average modulus decreases gradually with increasing temperature;with increasing angle αof the fissure,the evolution characteristics of the macro-mechanical parameters of sandstone are closely related to the their own mechanical properties.When the temperature is 800 ℃,the correlation between the peak strength and average modulus of sandstone and the angle α of the fissure is obviously weakened.The failure modes of sandstone containing fissures after high temperature exposure are of three different kinds including:tensile crack failure,tensile and shear cracks mixed failure,and shear crack failure.Tensile and shear crack mixed failure occur mainly at low temperatures and small angles;tensile crack failure occurs at high temperatures and large angles.

Research on windmill starting characteristics of MTE-D micro turbine engine

Micro turbine engine （MTE） is an important kind of propulsion system for miniature unmanned aircraft or missiles, because of its better high-speed performance （than propeller propulsion） and higher propulsion efficiency （obviously than rockets）. Windmill start is a common air-starting mode used in micro turbine engine. The windmill starting characteristics are important to the practical use of micro turbine engine. In this paper, the windmill starting characteristics research for a 12 cm diameter （MTE-D） micro turbine engine is carried out by experiment and numerical simulation. The characteristic of rotor mechanical losses at low-speed condition is stud- ied, and the engine common working line of windmill starting process is obtained. Based on the engine windmill characteristics, the propane ignition characteristics under different inflow conditions are researched, and the envelope of propane ignition and propane flameout is determined. The experimental research of fuel supply and ignition characteristics is completed, and the envelope of fuel supply and ignition is obtained. The windmill stage, propane ignition stage, fuel ignition stage and acceleration process from idling-speed to 80% full speed of MTE-D micro turbine engine is optimized, and the optimization windmill starting parameters are collected. The successful wind-mill starting experiment under this condition with engine speed up to 80% full speed indicates that these starting parameters are reasonable. All the starting parameters of MTE-D micro turbine engine obtained in this work are dimensionless parameters, and the conclusions obtained in this study have some reference to other micro turbine engines with the similar structural form and starting process.

Characterization of( Nb,Ti,Mo) C Precipitates in an Ultrahigh Strength Martensitic Steel

A study on ultrahigh strength steel plate subjected to novel thermo-mechanical control process was presented. The mechanical properties examination showed that the investigated steel exhibited excellent combination of ultra-high strength（ 2 200 MPa） and toughness（ 26 J）. The microstructure of the experimental steel was observed by scanning electron microscope and transmission electron microscope. Desired martensitic lath with width of about 180- 250 nm was obtained. Nanostructured carbide precipitates with sizes of 20-50 nm,which contained Nb,Ti and Mo,were observed in the lath martensitic microstructure,and confirmed to be MC-type carbides with B1 structure by means of selected area electron diffraction.The compositional characteristics revealed by energy dispersive X-ray spectrometer mapping implied that the carbide forming elements Nb,Ti and Mo distributed in the precipitates evenly. Three-dimensional atom probe tomography reconstruction further indicated that Mo incorporated into the precipitates without enrichment in the carbide-matrix interface and probably substituted for Nb and Ti to form the（ Nb,Ti,Mo） C carbides.

Insights on pretreatment of Indian hematite fines in grate-kiln pelletizing process： the choice of grinding processes

Indian hematite fines are normally characterized by high iron grade and minor impurities, which are usually used for sinter fines. With macroscale operations technology of blast furnace in Indian, pellets, as a kind of high-quality materials, attract more and more attention. However, the hematite fines possess the coarse size. Hence, they inevitably need to be further finely ground for pelletizing before balling. The grinding behavior of Indian hematite fines was revealed by conducting the ball milling tests and determining the Bond ball mill work index （Wi）. The results show that Indian hematite fines have an excellent grindability with Wi of only 7.40-7.73 kWh/t, indicating that ball milling is an economically viable way to pretreat Indian hematite fines. Nonetheless, due to poor sedimentation and filtering properties of wet ground products, the dry ball milling is more appropriate to process Indian hematite fines. In addition, the superior quality green balls can be manufactured with dry ground products under the conditions of 0.5% bentonite dosage, 7.5% moisture and balling for 12 min, which further confirmed that the recommended pellet feed preparation technique is reasonable.