Fabrication of Graphene/Cu Composite by Chemical Vapor Deposition and Effects of Graphene Layers on Resultant Electrical Conductivity

Graphene(Gr)has unique properties including high electrical conductivity;Thus,graphene/copper(Gr/Cu)composites have attracted increasing attention to replace traditional Cu for electrical applications. However,the problem of how to control graphene to form desired Gr/Cu composite is not well solved. This paper aims at exploring the best parameters for preparing graphene with different layers on Cu foil by chemical vapor deposition(CVD)method and studying the effects of different layers graphene on Gr/Cu composite’s electrical conductivity. Graphene grown on single-sided and double-sided copper was prepared for Gr/Cu and Gr/Cu/Gr composites. The resultant electrical conductivity of Gr/Cu composites increased with decreasing graphene layers and increasing graphene volume fraction. The Gr/Cu/Gr composite with monolayer graphene owns volume fraction of less than 0.002%,producing the best electrical conductivity up to59.8 ×10^(6)S/m,equivalent to 104.5% IACS and 105.3% pure Cu foil.

Purification of Single-walled Carbon Nanotubes Grown by a Chemical Vapour Deposition(CVD) Method

A procedure for purification of single walled carbon nanotubes(SWNTs) grown by the chemical vapour deposition(CVD) of carbon monooxide has been developed. Based on the result from TGA/DTA of as prepared sample, the oxidation temperature was determined. The process included sonication, oxidation and acid washing steps. The purity and yield after purification were determined and estimated by TEM. Moreover, for the first time, a loop structure for CVD SWNTs has been observed.

C-H-F氛围下金刚石薄膜的低温CVD生长过程分析

基于第一性原理的密度泛函理论对C-H-F氛围下低温CVD金刚石薄膜的生长过程进行仿真分析,计算H、F原子在氢终止金刚石表面发生萃取反应的吸附能、反应热与反应能垒,并分析CF_(3)、CF_(2)、CF 3种生长基团在带有活性位点基底上的吸附。结果表明:与H原子相比,F原子更容易在氢终止金刚石表面萃出H,并以HF形式脱附,且在C-H-F氛围下有利于在低温时产生更多的活性位点;CF_(3)、CF_(2)、CF基团在吸附后的结构和吸附能绝对值都更有利于金刚石相的生成,适当提高CF_(3)、CF_(2)、CF基团的浓度有助于实现金刚石相的更高速率生长。

Fabrication of 160-nm T-gate metamorphic AlInAs/GaInAs HEMTs on GaAs substrates by metal organic chemical vapour deposition

The fabrication and performance of 160-nm gate-length metamorphic AlInAs/GaInAs high electron mobility transistors （mHEMTs） grown on GaAs substrate by metal organic chemical vapour deposition （MOCVD） are reported. By using a novel combined optical and e-beam photolithography technology, submicron mHEMTs devices have been achieved. The devices exhibit good DC and RF performance. The maximum current density was 817 mA/mm and the maximum transconductance was 828 mS/mm. The non-alloyed Ohmic contact resistance Rc was as low as 0.02 Ω- ram. The unity current gain cut-off frequency （fT） and the maximum oscillation frequency （fmax） were 146 GHz and 189 GHz, respectively. This device has the highest fT yet reported for a 160-nm gate-length HEMTs grown by MOCVD. The output conductance is 28.9 mS/mm, which results in a large voltage gain of 28.6, Also, an input capacitance to gate-drain feedback capacitance ratio, Cgs/Cgd, of 4.3 is obtained in the device.

Electron field emission characteristics of nano-catkin carbon films deposited by electron cyclotron resonance microwave plasma chemical vapour deposition

This paper reported that the nano-catkin carbon films were prepared on Si substrates by means of electron cyclotron resonance microwave plasma chemical vapour deposition in a hydrogen and methane mixture. The surface morphology and the structure of the fabricated films were characterized by using scanning electron microscopes and Raman spectroscopy, respectively. The stable field emission properties with a low threshold field of 5V/μm corresponding to a current density of about 1μA/cm^2 and a current density of 3.2mA/cm^2 at an electric field of 10V/μm were obtained from the carbon film deposited at CH4 concentration of 8%. The mechanism that the threshold field decreased with the increase of the CH4 concentration and the high emission current appeared at the high CH4 concentration was explained by using the Fowler-Nordheim theory.

Influence of double AlN buffer layers on the qualities of GaN films prepared by metal-organic chemical vapour deposition

In this paper we report that the GaN thin film is grown by metal-organic chemical vapour deposition on a sapphire （0001） substrate with double A1N buffer layers. The buffer layer consists of a low-temperature （LT） A1N layer and a high-temperature （HT） A1N layer that are grown at 600 ℃ and 1000 ℃, respectively. It is observed that the thickness of the LT-A1N layer drastically influences the quality of GaN thin film, and that the optimized 4.25-min-LT-A1N layer minimizes the dislocation density of GaN thin film. The reason for the improved properties is discussed in this paper.

The high deposition of microcrystalline silicon thin film by very high frequency plasma enhanced chemical vapour deposition and the fabrication of solar cells

This paper reports that the intrinsic microcrystalline silicon （μc-Si：H） films are prepared with plasma enhanced chemical vapour deposition from silane/hydrogen mixtures at 200℃ with the aim to increase the deposition rate. An increase of the deposition rate to 0.88 nm/s is obtained by using a plasma excitation frequency of 75 MHz. This increase is obtained by the combination of a higher deposition pressure, an increased silane concentration, and higher discharge powers. In addition, the transient behaviour, which can decrease the film crystallinity, could be prevented by filling the background gas with H2 prior to plasma ignition, and selecting proper discharging time after silane flow injection. Material prepared under these conditions at a deposition rate of 0.78nm/s maintains higher crystallinity and fine electronic properties. By H-plasma treatment before i-layer deposition, single junction μc-Si：H solar cells with 5.5% efficiency are fabricated.

Field emission characteristics of nano-sheet carbon films deposited by quartz-tube microwave plasma chemical vapour deposition

Nano-sheet carbon films are prepared on Si wafers by means of quartz-tube microwave plasma chemical vapour deposition （MPCVD） in a gas mixture of hydrogen and methane. The structure of the fabricated films is investigated by using field emission scanning electron microscope （FESEM） and Raman spectroscopy. These nano^carbon films are possessed of good field emission （FE） characteristics with a low threshold field of 2.6 V/μm and a high current density of 12.6 mA/cm^2 at an electric field of 9 V/μm. As the FE currents tend to be saturated in a high E region, no simple Fowler-Nordheim （F-N） model is applicable. A modified F N model considering statistic effects of FE tip structures and a space-charge-limited-current （SCLC） effect is applied successfully to explaining the FE data observed at low and high electric fields, respectively.

Development of Electrospray Laser Chemical Vapour Deposition for Homogenous Alumina Coatings

Electrospray,as a liquid source supply system,has been applied to chemical vapour deposition（CVD）.In thermal CVD,the microstructure of the obtained films changes from dense to coarse granular because of the decreasing surface temperature during deposition.Using the electrospray laser chemical vapour deposition method,we prepared homogenous alumina coatings.We found that laser irradiation was effective in compensating the surface temperature decrease,and an alpha-alumina coating with dense columnar microstructures was obtained at a deposition rate of 200 μm/h using 200 W Nd：YAG laser irradiation.

Characterization of GaSb Films by Metalorganic Chemical Vapour Deposition

GaSb epilayers were grown on GaSb and GaAs substrates by atmospheric pressure metalorganic chemical vapor deposition (MOCVD). The properties of GaSb layers were characterized by low temperature photoluminescence (PL) spectra and scanning electron acoustic microscopy (SEAM) images. The temperature dependence of the PL spectrum was investigated and a red shift of bound excitons was observed in high quality epilayer. The pyramids of the surface and the buried subsurfaces were observed by scanning electron microscopy (SEM) and scanning electron acoustic microscopy (SEAM), and their growth model was discussed.

The effects of sapphire nitridation on GaN growth by metalorganic chemical vapour deposition

In situ optical reflectivity measurements are employed to monitor the GaN epilayer growth process above a lowtemperature GaN buffer layer on a c-plane sapphire substrate by metalorganic chemical vapour deposition. It is found that the lateral growth of the GaN islands and their coalescence are promoted in the initial growth stage if optimized nitridation time and temperature are selected when the substrate is pre-exposed to ammonia. As confirmed by atomic force microscopy observations, the quality of the CaN epilayers is closely dependent on the surface morphology of the nitridated buffer layer, especially grain size and nucleation density.

Growth and characterization of InAsSb alloys by metalorganic chemical vapour deposition

Low pressure metalorganic chemical vapour deposition （LP-MOCVD） growth and characteristics of InAsSb on （100） GaSb substrates are investigated. Mirror-like surfaces with a minimum lattice mismatch are obtained. The samples are studied by photoluminescence spectra, and the output is 3.17μm in wavelength. The surface of InAsSb epilayer shows that its morphological feature is dependent on buffer layer. With an InAs buffer layer used, the best surface is obtained. The InAsSb film shows to be of n-type conduction with an electron concentration of 8.52 × 10^16 cm^-3.

Photoluminescence and lasing properties of InAs/GaAs quantum dots grown by metal-organic chemical vapour deposition

Photoluminescence （PL） and lasing properties of InAs/GaAs quantum dots （QDs） with different growth procedures prepared by metalorganic chemical vapour deposition are studied. PL measurements show that the low growth rate QD sample has a larger PL intensity and a narrower PL line width than the high growth rate sample. During rapid thermal annealing, however, the low growth rate sample shows a greater blueshift of PL peak wavelength. This is caused by the larger InAs layer thickness which results from the larger 2-3 dimensional transition critical layer thickness for the QDs in the low-growth-rate sample. A growth technique including growth interruption and in-situ annealing, named indium flush method, is used during the growth of GaAs cap layer, which can flatten the GaAs surface effectively. Though the method results in a blueshift of PL peak wavelength and a broadening of PL line width, it is essential for the fabrication of room temperature working QD lasers.

Structural Evolution of SiC Films During Plasma-Assisted Chemical Vapour Deposition

Evolution of chemical bonding configurations for the films deposited from hexam- ethyldisiloxane （HMDSO） diluted with H2 during plasma assisted chemical vapour deposition is investigated. In the experiment a small amount of CH4 was added to adjust the plasma environment and modify the structure of the deposited films. The measurements of Raman spectroscopy and X-ray diffraction （XRD） revealed the production of 6H-SiC embedded in the amorphous matrix without the input of CH4. As CH4 was introduced into the deposition reaction, the transition of 6H-SiC to cubic SiC in the films took place, and also the film surfaces changed from a structure of ellipsoids to cauliflower-like shapes. With a further increase of CH4 in the flow ratio, the obtained films varied from Si-C bonding dominant to a sp^2/sp^3 carbon-rich composition.

SiC epitaxial layers grown by chemical vapour deposition and the fabrication of Schottky barrier diodes

This paper presents the results of unintentionally doped 4H-SiC epilayers grown on n-type Si-faced 4H-SiC substrates with 8° off-axis toward the [1120] direction by low pressure horizontal hot-wall chemical vapour deposition. Growth temperature and pressure are 1580 ℃ and 10^4 Pa, respectively. Good surface morphology of the sample is observed using atomic force microscopy （AFM） and scanning electron microscopy （SEM）. Fourier transform infrared spectroscopy （FTIR） and x-ray diffraction （XRD） are used to characterize epitaxial layer thickness and the structural quality of the films respectively. The carrier concentration in the unintentional 4H-SiC homoepitaxial layer is about 6.4×10^14 cm^-3 obtained by C-V measurements. Schottky barrier diodes （SBDs） are fabricated on the epitaxial wafer in order to verify the quality of the wafer and to obtain information about the correlation between background impurity and electrical properties of the devices. Ni and Ti/4H-SiC Schottky barrier diodes with very good performances were obtained and their ideality factors are 1.10 and 1.05 respectively.

Influence of oxygen on the growth of cubic boron nitride thin films by plasma-enhanced chemical vapour deposition

Cubic boron nitride thin films were deposited on silicon substrates by low-pressure inductively coupled plasmaenhanced chemical vapour deposition. It was found that the introduction of 02 into the deposition system suppresses both nucleation and growth of cubic boron nitride. At a B2H6 concentration of 2.5% during film deposition, the critical O2 concentration allowed for the nucleation of cubic boron nitride was found to be less than 1.4%, while that for the growth of cubic boron nitride was higher than 2.1%. Moreover, the infrared absorption peak observed at around 1230- 1280 cm^-1, frequently detected for cubic boron nitride films prepared using non-ultrahigh vacuum systems, appears to be due to the absorption of boron oxide, a contaminant formed as a result of the oxygen impurity. Therefore, the existence of trace oxygen contamination in boron nitride films can be evaluated qualitatively by this infrared absorption peak.

Influence of ignition condition on the growth of silicon thin films using plasma enhanced chemical vapour deposition

The influences of the plasma ignition condition in plasma enhanced chemical vapour deposition （PECVD） on the interfaces and the microstructures of hydrogenated microcrystalline Si （μc-Si：H） thin films are investigated. The plasma ignition condition is modified by varying the ratio of Sill4 to H2 （RH）. For plasma ignited with a constant gas ratio, the time-resolved optical emission spectroscopy presents a low value of the emission intensity ratio of Ha to Sill＊ （Iuα//SiH＊） at the initial stage, which leads to a thick amorphous incubation layer. For the ignition condition with a profiling RH, the higher IHα/ISiH＊ values are realized. By optimizing the RN modulation, a uniform crystallinity along the growth direction and a denser αc-Si：H film can be obtained. However, an excessively high IRα/ISIH＊ may damage the interface properties, which is indicated by capacitance-voltage （C-V） measurements. Well controlling the ignition condition is critically important for the applications of Si thin films.

The properties of GaMnN films grown by metalorganic chemical vapour deposition using Raman spectroscopy

An investigation of room-temperature Raman scattering is carried out on ferromagnetic semiconductor GaMnN films grown by metalorganic chemical vapour deposition with different Mn content values. New bands around 300 and 669 cm-1, that are not observed in undoped GaN, are found. They are assigned to disorder-activated mode and local vibration mode （LYM）, respectively. After annealing, the intensity ratio between the LVM and E2（high） mode, i.e., ILVM/IE2 （high）, increases. The LO phonon-plasmon coupled （LOPC） mode is found in GaMnN, and the frequency of the LOPC mode of GaMnN shifting toward higher side is observed with the increase in the Mn doping in GaN. The ferromagnetic character and the carrier density of our GaMnN sample are discussed.

Growth of aligned single-walled carbon nanotubes under ac electric fields through floating catalyst chemical vapour deposition

Through floating catalyst chemical vapour deposition（CVD） method, well-aligned isolated single-walled carbon nanotubes （SWCNTs） and their bundles were deposited on the metal electrodes patterned on the SiO2/Si surface under ac electric fields at relatively low temperature（280℃）. It was indicated that SWCNTs were effectively aligned under ac electric fields after they had just grown in the furnace. The time for a SWCNT to be aligned in the electric field and the effect of gas flow were estimated. Polarized Raman scattering was performed to characterize the aligned structure of SWCNTs. This method would be very useful for the controlled fabrication and preparation of SWCNTs in practical applications.