Study of steam heat transfer enhanced by CO_(2) and chemical agents: In heavy oil production

Steam flooding with the assistance of carbon dioxide (CO_(2)) and chemicals is an effective approach for enhancing super heavy oil recovery. However, the promotion and application of CO_(2) and chemical agent-assisted steam flooding technology have been restricted by the current lack of research on the synergistic effect of CO_(2) and chemical agents on enhanced steam flooding heat transfer. The novel experiments on CO_(2)–chemicals cooperate affected steam condensation and seepage were conducted by adding CO_(2) and two chemicals (sodium dodecyl sulfate (SDS) and the betaine temperature-salt resistant foaming agent ZK-05200).According to the experimental findings, a “film” formed on the heat-transfer medium surface following the co-injection of CO_(2) and the chemical to impede the steam heat transfer, reducing the heat transfer efficiency of steam, heat flux and condensation heat transfer coefficient. The steam seepage experiment revealed that the temperature at the back end of the sandpack model was dramatically raised by 3.5–12.8 °C by adding CO_(2) and chemical agents, achieving the goal of driving deep-formation heavy oil. The combined effect of CO_(2) and SDS was the most effective for improving steam heat transfer, the steam heat loss was reduced by 6.2%, the steam condensation cycle was prolonged by 1.3 times, the condensation heat transfer coefficient was decreased by 15.5%, and the heavy oil recovery was enhanced by 9.82%. Theoretical recommendations are offered in this study for improving the CO_(2)–chemical-assisted steam flooding technique.

Decomposition kinetics of dimethyl methylphospate(chemical agent simulant) by supercritical water oxidation

Supercritical water oxidation （SCWO） has been drawing much attention due to effectively destroy a large variety of high-risk wastes resulting from munitions demilitarization and complex industrial chemical. An important design consideration in the development of supercritical water oxidation is the information of decomposition rate. In this paper, the decomposition rate of dimethyl methylphosphonate（DMMP）, which is similar to the nerve agent VX and GB（Sarin） in its structure, was investigated under SCWO conditions. The experiments were performed in an isothermal tubular reactor with a H2O2 as an oxidant. The reaction temperatures were ranged from 398 to 633℃ at a fixed pressure of 24 MPa. The conversion of DMMP was monitored by analyzing total organic carbon （TOC） on the liquid effluent samples. It is found that the oxidative decomposition of DMMP proceeded rapidly and a high TOC decomposition up to 99.99% was obtained within 11 s at 555℃. On the basis of data derived from experiments, a global kinetic equation for the decomposition of DMMP was developed. The model predictions agreed well with the experimental data.

Surface Decontamination of Chemical Agent Surrogates Using an Atmospheric Pressure Air Flow Plasma Jet

An atmospheric pressure dielectric barrier discharge （DBD） plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless steel or iron plate painted with alkyd or PVC. The experi- mental results of material decontamination show that the residual chemical agent on the material is lower than the permissible value of the National Military Standard of China. In order to test the corrosion effect of the plasma jet on different material surfaces in the decontamination pro-cess, corrosion tests for the materials of polymethyl methacrylate, neoprene, polyvinyl chloride （PVC）, polyethylene （PE）, phenolic resin, iron plate painted with alkyd, stainless steel, aluminum, etc. were carried out, and relevant parameters were examined, including etiolation index, chroma- tism, loss of gloss, corrosion form, etc. The results show that the plasma jet is slightly corrosive for part of the materials, but their performances are not affected. A portable calculator, computer display, mainboard, circuit board of radiogram, and a hygrometer could work normally after being treated by the plasma jet.

Comparative Study on the Efficacies of 11 Chemical Agents against Taro Soft Rot Caused by Pectobacterium aroidearum

[Objective]The paper was to screen the effective agents for effectively controlling the occurrence and prevalence of taro soft rot.[Method]The fungicidal effects of 11 fungicides on taro soft rot were determined by inhibition zone method.[Result]0.3%Tetramycin,25%bromothalonil,3%Zhongshengmycin and 30%zinc thiazole had better antifungal effect on Pectobacterium aroidearum at recommended concentration.The indoor toxicity of four fungicides showed that the EC50 of 0.3%tetramycin AS was the smallest of 0.6μg/mL,indicating that tetramycin had the largest toxicity and the best inhibitory effect against P.aroidearum;followed by 25%bromothalonil EC and 3%Zhongshengmycin WP,with the EC_(50) of 2.57 and 97.72μg/mL,respectively;the inhibitory effect of 30%zinc thiazole SC against P.aroidearum was the poorest.[Conclusion]The study provides a reference for screening out new and efficient chemical agents against taro soft rot.

Study on scattering properties of tissues with hyperosmotic chemical agents

Optical properties of biological tissue are variable due to the changes of micro-structures and scattering constituents after hyperosmotic chemical agents permeates into tissue. The changes of optical properties of biological tissue are due to the refractive indices matching between the scatterers with high refractive index and the ground substances, which reduce scattering of tissue. The main reasons are that permeated semipermeable chemical agents with higher refractive index than the ground substances of tissue makes the refractive index of ground substances of tissue higher by the enhancement of the permeated concentration. We studied on the collimated transmittance changes of light penetrating biological tissue after the hyperosmotic chemical agents administrates with different concentration.

Detection and Analysis of Chemical Agents in Sun-proof Products

15 chemical sunscreen agents in 220 batches of sun-proof products were tested,and the test results were checked with the product labels and approvals,and the problems found were compared and analyzed.There were some inconsistencies among the actual ingredients,labeling ingredients and approval ingredients in the sun-proof products on the market,and the problem of insufficient input of raw materials was prominent.The supervision of this kind of products should be strengthened so as to reduce the safety risk of consumers using this kind of products.

Multiple chemical warfare agent simulant decontamination by self-driven microplasma

Low-temperature plasma is a green and high-efficiency technology for chemical warfare agent(CWA)decontamination.However,traditional plasma devices suffer from the problems of highpower composition and large power-supply size,which limit their practical applications.In this paper,a self-driven microplasma decontamination system,induced by a dielectric-dielectric rotary triboelectric nanogenerator(dd-r TENG),was innovatively proposed for the decontamination of CWA simulants.The microplasma was characterized via electrical measurements,optical emission spectra and ozone concentration detection.With an output voltage of-3460 V,the dd-r TENG can successfully excite microplasma in air.Reactive species,such as OH,O(1D),Hαand O3were detected.With input average power of 0.116 W,the decontamination rate of 2-chloroethyl ethyl sulfide reached 100%within 3 min of plasma treatment,while the decontamination rates of malathion and dimethyl methylphosphonate reached(65.92±1.65)%and(60.88±1.92)%after 7 min of plasma treatment,respectively.In addition,the decontamination rates gradually decreased with the increase in the simulant concentrations.Typical products were identified and analyzed.This study demonstrates the broad spectrum and feasibility of the dd-r TENG-microplasma for CWA elimination,which provides significant guidance for their practical applications in the future.

Programmed cell death, antioxidant response and oxidative stress in wheat f lag leaves induced by chemical hybridization agent SQ-1

Male sterility induced by a chemical hybridization agent （CHA） is an important tool for utilizing crop heterosis. Leaves, especially the flag leaves, as CHA initial recipients play a decisive role in inducing male sterility. To investigate effects of different treatment times of CHA-SQ-1 used, morphological, biochemical and physiological responses of wheat flag leaves were detected in thistudy. CHA induced programmed cell death （PCD） as shown in terminal deoxynucleotidyl transferase-mediated dUTP nick end-labelling （TUNEL） and DNA laddering analysis. In the early phase, CHA-SQ-1 trig- gered organelle changes arid PCD in wheat leaves accompanied by excess production of reactive oxygen species （O2- and H202） and down-regulation of the activities of superoxide dismutase （SOD）, catalase （CAT） and guaiacol peroxidase （POD）. Meanwhile, leaf cell DNAs showed ladder-like patterns on agarose gel, indicating that CHA-SQ-1 led to the activation of the responsible endonuclease. The oxidative stress assays showed that lipid peroxidation was strongly activated and photosynthesis was obviously inhibited in SQ-l-induced leaves. However, CHA contents in wheat leaves gradually reduced along with the time CHA-SQ-1 applied. Young flags returned to an oxidative/antioxidative balance and ultimately developed into mature green leaves. These results provide explanation of the relations between PCD and anther abortion and practical application of CHA for hybrid breeding.

Laboratory investigation into the use of soundless chemical demolitions agents for the breakage of hard rock

The method of drilling and blasting with explosives is widely used in rock fragmentation applications in the mining industry for mine development and ore production.However,the use of explosives is associated with rigorous safety and environmental constraints as blasting creates toxic fumes,ground vibrations,and dust.This study is focused on the use of Soundless Chemical Demolition Agents(SCDA)as a more environmentally friendly method for rock breakage and a potential replacement of explosives.In this paper,the results of a series of experimental tests are reported to identify the efect of SCDA on hard rock breakage under no load and under uniaxial loading conditions.Stanstead granite prismatic specimens of 152.4 mm(6″)×152.4–203.2 mm(6–8″)×406.4 mm(16″)are used to test the infuence of borehole size on the time to fracturing with SCDA borehole size of 25.4 mm(1″),31.75 mm(1.25″)and 38.1 mm(1.5″).It is shown that the fracturing time decreases with increasing borehole size.It is also shown that specimens subjected to uniaxial compression of 5 MPa fracture as early as 7 h after SCDA mixing.A borehole spacing to borehole diameter ratio of 12.8 to 14.6 is suggested for practical applications.

A prototype portable instrument employing micro-preconcentrator and FBAR sensor for the detection of chemical warfare agents

The presence of chemical warfare agents(CWAs)in the environment is a serious threat to human safety,but there are many problems with the currently available detection methods for CWAs.For example,gas chromatography–mass spectrometry cannot be used for in-field detection owing to the rather large size of the equipment required,while commercial sensors have the disadvantages of low sensitivity and poor selectivity.Here,we develop a portable gas sensing instrument for CWA detection that consists of a MEMSfabricated micro-preconcentrator(μPC)and a film bulk acoustic resonator(FBAR)gas sensor.The μPC is coated with a nanoporous metal–organic framework material to enrich the target,while the FBAR provides rapid detection without the need for extra carrier gas.Dimethyl methylphosphonate(DMMP),a simulant of the chemical warfare agent sarin,is used to test the performance of the instrument.Experimental results show that the μPC provides effective sample pretreatment,while the FBAR gas sensor has good sensitivity to DMMP vapor.The combination of μPC and FBAR in one instrument gives full play to their respective advantages,reducing the limit of detection of the analyte.Moreover,both the μPC and the FBAR are fabricated using a CMOS-compatible approach,and the prototype instrument is compact in size with high portability and thus has potential for application to in-field detection of CWAs.

Protection of armoured vehicles against chemical, biological and radiological contamination

The article presents problems related to mechanical protection of vehicles with different add-on armours against chemical,biological and radiological contamination.This applies to vehicles with additional passive,reactive and hybrid protection in the form of cassettes against piercing with anti-tank projectiles,piercing with their kinetic energy of impact,and as a result of chemical energy of shaped charges as well as explosively formed projectiles.It has been shown how increased ballistic protection of these vehicles at the same time reduces their decontaminability in various places of the vehicle due to the increased additional surface of the vehicle with cassettes.Prevention of contamination of these cassettes has been presented as a way of reducing hard to reach surface for decontamination and a method of insulating construction elements(stands),fixing these cassettes to the vehicle,from the environment to prevent contact with contaminated liquids and dusts.The selection of appropriate materials is shown,which may affect the improvement of the decontamination efficiency of the vehicle with such cassettes.This applies to the use of materials with low absorption of chemical warfare agents,which prevent the accumulation of large amounts of these agents on contaminated surfaces and improve the effectiveness of decontamination.It also shows how to ensure better access of the disinfectant to as much of the vehicle surface as possible,covered with cassettes that have been contaminated.It shows how a vehicle,in particular with such cassettes,can provide protection against radar detection when Radar Absorbent Material is used on vehicle cassettes.

Field-deployable rapid multiple biosensing system for detection of chemical and biological warfare agents

The threat of biological and chemical terror acts remains a growing worldwide concern.There is therefore a need to develop appropriate technology for the detection of chemical and biological warfare agents,with early identification intended for use by first responders.Here,we disclose the developed autonomous air sampling and detection system for evaluation of the presence of chemical and biological warfare agents that can be harmful to the population.The current device utilizes the designed mist generator-assisted air collection system(338 l min^(−1))and biosensing chip technologies,such as electrochemical measurement,Au nanoparticle-based localized surface plasmon resonance,and rapid microfluidic chip PCR for detection of minute concentrations lower than the mean lethal dose(LD_(50))of nerve gases(sarin and VX),toxic proteins(BTX/A/Hc and ricin),and pathogens(anthrax simulant).An operation time of only 5–15 min is needed for the collection and detection;sample preparation is already integrated into the system without the need for direct human intervention.In addition to the system’s sensitivity and ease of use,its portability makes it highly beneficial for first responders,which could aid in immediate risk assessment and mitigation of on-site events.

Portable System for CWA Detection Using Micro Array Gas Sensor

Biochemistry weapon is raising new tools of war and terror.This research is an experiment about portable system for CWAs (chemical warfare agents) detection using micro array gas system.CWAs were divided into four types such as blood, nerve,vesicant,and choking agent.To detect various CWAs,semiconductor thick film sensor array based on tin oxide was fabricated and their gas responses were examined.Operating temperature was range of 250℃to 350℃and gas concentration was range of 0.1μg/g to 10μg/g.Sensor array was measured as operating temperatures,concentrations for four simulant agents of CWAs.Extracted parameters from results were carried out classification among CWAs through the principal component analysis (PCA).Also,classification of gases is studied using adaptive resonance theory (ART) that is one of neural network algorithm.Results displayed using PDA system.

Screening and Analysis of Proteins Interacting with TaPDK from Physiological Male Sterility Induced by CHA in Wheat

To further research the regulatory network of pyruvate dehydrogenase kinase （designated as TaPDK） in physiological male-sterility （PHYMS） of wheat induced by chemical hybridizing agent （CHA） SQ-1, an anther cDNA library was constructed, and the proteins interacting with TaPDK were screened via yeast two-hybrid technique. Subsequently, a few candidate proteins in nucleotide expression levels were detected by real-time quantitative PCR. Yeast-two hybrid screening was performed by mating yeast strain Y2HGold containing BD-TaPDK bait plasmid with yeast strain Y187 including anther cDNA library plasmid. Diploid yeast cells were plated on synthetic dropout nutrient medium （SD/-Ade/-His/-Leu/-Trp） （QDO）, and further were incubated on QDO medium containing AbA and X-α-Gal. The interactions between TaPDK and the proteins obtained from positive colonies were further confirmed by co-transformation validation. After plasmids DNA were extracted from blue colonies and sequenced, the sequences results were analyzed by bioinformatic methods. Finally, 24 colonies were obtained, including eight genes, namely non-specific lipid-transfer protein precursor （TanLTP）, polyubiquitin （TaPUbi）, glyceraldehyde-3-phosphate dehydrogenase, proliferating cell nuclear antigen （TaPCNA）, CBS domain containing protein （TaCBS）, actin, guanine nucleotide-binding protein beta subunit, chalcone synthase, and three new genes with unknown function. The results of quantitative RT-PCR showed that the expression levels of TanLTP, TaPUbi, and TaPCNA were obviously up-regulated in PHYMS anther, and TaCBS expression was only increased at the tricellular stage in PHYMS anther compared with in fertile lines. Whereas, the expression of TaPDK was obviously down-regulated in PHYMS lines. Collectively, these datas indicated that the majority of candidate proteins might be related to pollen abortion in PHYMS lines, which further suggested that TaPDK plays multiple roles in pollen development, besides participating in regulating pyruvate dehydrogenase complex activity.

Wearable membranes from zirconium-oxo clusters cross-linked polymer networks for ultrafast chemical warfare agents decontamination

The urgent need for immediate personal protection against chemical warfare agents(CWAs)spurs the requirement on robust and highly efficient catalytic systems that can be conveniently integrated to wearable devices.Herein,as a new concept for CWA decontamination catalyst design,sub-nanoscale,catalytically active zirconium-oxo molecular clusters are covalently integrated in flexible polymer network as crosslinkers for the full exposure of catalytic sites as well as robust framework structures.The obtained membrane catalysts exhibit high swelling ratio with aqueous content as 84 wt%and therefore,demonstrate quasi-homogeneous catalytic activity toward the rapid hydrolysis of both CWA,soman(GD)(t_(1/2)=5.0 min)and CWA simulant,methyl paraoxon(DMNP)(t_(1/2)=8.9 min).Meanwhile,due to the covalent nature of cross-linkages and the high flexibility of polymer strands,the membranes possess promising mechanical strength and toughness that can stand the impact of high gas pressures and show high permeation for both CO_(2)and O_(2),enabling their extended applications in the field of collective/personal protective materials with body comfort.

A crosslinking hydrogel binder for high-sulfur content S@pPAN cathode in rechargeable lithium batteries

High-energy density lithium-sulfur(Li-S) batteries have received intensive attention as promising energy storage system.Among diverse sulfur-based cathodes,sulfurized pyrolyzed poly(acrylonitrile)(S@pPAN)cathode delivered superior electrochemical performance.However,the sulfur content of S@pPAN is relatively low(<50 wt%),which significantly limits the energy density.Herein,a hydrogel SA-Cu binder was proposed with a crosslinking network constructed by Cu^(2+) ions.The introduction of Cu^(2+) ions enabled excellent electrochemical behaviors of S@pPAN cathode even with high sulfur content of 52.6 wt% via chemical interaction with sulfur and polysulfide.Moreover,a favorable cathode interphase was formed containing electrochemically active and conductive CuSx.S@pPAN/SA-Cu exhibited a high sulfur utilization of 85.3%,long cycling stability over 1000 cycles and remarkable capacity of 1200 mAh g_(s)^(-1) even at10 C.Furthermore,ascribed to the improved electrode structure,high-loading electrode(sulfur loading:4 mg cm^(-2)) displayed stable cycling with areal capacity of 5.26 mAh cm^(-2)(1315 mAh g_(s)^(-1)) after 40 cycles.This study provides new directions to prepare high-sulfur content and high-loading S@pPAN cathode for higher energy density.

Synthesis and Gas Sensing of TiO_2 Ultrafine Powders by Precipitating

We investigated the gas sensing characteristics of rutile and anatase TiO_2 nano-particle sensors for chemical warfare agents.TiO_2 nano-powders with rutile and anatase structure were fabricated by controlling pH value without heat treatment respectively.The mean particle size of TiO_2 powders were below 10 nm.As-prepared TiO_2 powders have several advantages of nano particle size and high surface area and could be a prominent candidate for nano-sensors.TiO_2 sensors were examined with DMMP for chemical warfare agents detection.

Rapid destruction of sarin surrogates by gas phase reactions with focus on diisopropyl methylphosphonate(DIMP)

Rapid destruction of stockpiles of sarin and other chemical weapon agents(CWA)requires understanding and quantitative description of the relevant chemical reactions.Rapid reactions at elevated temperatures are of particular interest for prompt agent defeat scenarios.Diisopropyl methylphosphonate(DIMP)is a sarin surrogate particularly well suited to model sarin thermal decomposition and is often used in experiments.This article is a review of different experimental methods addressing decomposition of gasified DIMP,respective results and their interpretations.Major early decomposition products are propene,methylphosphonic acid,methyl(oxo)phosphoniumolate,and isopropanol.Early computational work using available kinetic data for fluorine and the phosphorus-fluorine bond predicted the decomposition under incineration conditions.Experiments using an isothermal flow reactor operated at 700-800 K were used to model DIMP decomposition as unimolecular reaction with results that were consistent with the earlier theoretical work.Decomposition in dynamic environments was studied using DIMP supported on rapidly heated substrates.The results showed different decomposition products and product sequences forming at different heating rates,suggesting the need for revised reaction kinetics.However,species quantification in such experiments is difficult because of inherent large temperature gradients.Plasma produced in a corona discharge was also reported to lead to rapid DIMP decomposition at low temperatures.Decomposition products were distinct from those observed at high temperatures.Shock tube experiments may be well suited to study decomposition of organophosphorus compounds like DIMP following their rapid heating in diverse environments.However,presently,only sarin surrogates other than DIMP have been investigated,and no intermediate reaction products,important for developing a validated mechanism,could be detected.

Vapor-phase decomposition of dimethyl methylphosphonate (DMMP),a sarin surrogate,in presence of metal oxides

Chemical warfare agents(CWA)are stockpiled in large quantities across the globe.Agents stored in inaccessible facilities need to be destroyed rapidly without dispersing the compounds to surrounding areas.Metal-based energetic formulations are used in such prompt defeat applications to rapidly decompose the CWA by generating a high temperature environment.An alternate,and possibly a more effective decomposition pathway could be provided by chemicidal action of aerosolized condensed combustion products,which typically consist of metal oxides.Toxic fumes that escape the high temperature blast zone can be neutralized by smoke generated during combustion,depending on the particle size,surface characteristics,chemical properties,and concentration of this smoke.This review considers relevant experimental and modeling studies quantifying decomposition of CWA comprising organophosphorus compounds and their surrogates on the surface of various metal oxides.Dimethyl methylphosphonate(DMMP),a sarine surrogate,was used most commonly for such experiments.Many reported efforts focused on the mechanisms of adsorption of DMMP to various metal oxides and initial reaction steps cleaving various bonds from the chemisorbed molecules.For selected oxides,these experiments were supported by quantum-mechanical calculations.In other studies,the capacity of oxide surfaces to adsorb and decompose DMMP was quantified.In most cases,porous catalysts were used although limited experimental data are available for aerosolized nonporous oxide particles.The reported experimental data applicable to scenarios involving prompt decomposition of CWA are summarized.It is noted that information is lacking describing respective heterogeneous reaction kinetics.Preliminary estimates of aerosolized smoke particle concentrations required to destroy CWA are made considering gas phase diffusion rates and reported values of the oxide capacity to decompose CWA or their surrogates.

Synthesis, chemical nuclease activity, and in vitro cytotoxicity of benzimidazole-based Cu(Ⅱ)/Co(Ⅱ) complexes

In this study, novel mono/di-nuclear Cu（p-2-bmb）（OH）（Cl O4）（1） and Co2（p-2-bmb）2Cl4（2）（p-2-bmb = 1-（（2-（pyridin-2-yl）-benzoimidazol-1-yl）methyl）-1H-benzotriazole） complexes with the nitrogen heterocyclic benzimidazole-based ligand were synthesized and characterized. The two complexes showed antiproliferative effects in various carcinoma cell lines, especially complex 1 in the SMMC7721 tumor cell line. Complex 1 was also able to pass through the cell membrane and enter the nucleus and mitochondrion. An analysis of in vitro chemical nuclease activity revealed that complex 1 partially intercalated to calf thymus DNA and exhibited strong unwinding activity against p BR322 superhelical plasmid DNA. The comet assay and flow cytometry analysis confirmed that 1 caused extensive DNA damage and arrested SMMC7721 tumor cells at G2/M phase of the cell cycle, leading to loss of mitochondrial membrane potential and apoptosis. These results suggest that these benzimidazole-based metal complexes could be potential anti-cancer agents.