Effects of Temperature on Determination of Protein Concentration with Coomassie Brilliant Blue Method

[Objective] This study aimed to investigate the effects of temperature on determination of protein concentration with Coomassie Brilliant Blue method,thus proving advice and guidance for accurate determination of protein concentration.[Method] With Coomassie Brilliant Blue method,the concentrations of different bovine serum albumin samples were determined under different temperatures and incubation time.[Result] According to the standard curve,when the determination range of protein concentration was 0-100 mg/ml,the determined protein concentration was relatively stable after incubation at 20 ℃ for 20-30 min.Furthermore,the determination result of higher protein concentration with Coomassie Brilliant Blue method was less affected by various factors.[Conclusion] In determination of protein concentration with Coomassie Brilliant Blue method,temperature,sample concentration and incubation time were important factors affecting the accuracy of experimental results.

Response of Sea Surface Temperature to Chlorophyll-a Concentration in the Tropical Pacific:Annual Mean,Seasonal Cycle,and Interannual Variability

The response of the upper-ocean temperatures and currents in the tropical Pacific to the spatial distribution of chlorophyll-a and its seasonal cycle is investigated using a coupled atmosphere-ocean model and a stand-alone oceanic general circulation model.The spatial distribution of chlorophyll-a significantly influences the mean state of models in the tropical Pacific.The annual mean SST in the eastern equatorial Pacific decreases accompanied by a shallow thermocline and stronger currents because of shallow penetration depth of solar radiation.Equatorial upwelling dominates the heat budget in that region.Atmosphere-ocean interaction processes can further amplify such changes. The seasonal cycle of chlorophyll-a can dramatically change ENSO period in the coupled model.After introducing the seasonal cycle of chlorophyll-a concentration,the peak of the power spectrum becomes broad,and longer periods（3 years） are found.These changes led to ENSO irregularities in the model. The increasing period is mainly due to the slow speed of Rossby waves,which are caused by the shallow mean thermocline in the northeastern Pacific.

Synthesis of Water Utilization System Using Concentration Interval Analysis Method （ Ⅰ ） Non-Mass-Transfer-Based Operation

A strategy for water and wastewater minimization is developed for continuous water utilization systems involving fixed flowrate(non-mass-transfer-based)operations,based on the fictitious operations that is introduced to represent the water losing and/or generating operations and a modified concentration interval analysis(MCIA) technique.This strategy is a simple,nongraphical,and noniterative procedure and is suitable for the quick yields of targets and the identification of pinch point location.Moreover,on the basis of the target method,a heuristic-based approach is also presented to generate water utilization networks,which could be demonstrated to be optimum ones. The proposed approaches are illustrated with example problems.

The algorithms of chlorophyll-a concentration for CMODIS

The algorithms of extracting chlorophyll-a （Chl-a） concentration have been established for Chinese moderate resolution imaging spectrometer （CMODIS） mounted on Shenzhou-3 spaceship launched on 25 March 2002. The CMODIS is an ocean color sensor with 30 visible channels and 4 infrared channels, much different from other ocean color satellites and needs new algorithms to process data. Three models of Chl-a concentration were established based on Chl-a data retrieved from sea-viewing wide field-ofview sensor （SeaWiFS）, with the average relative errors of 26. 6%, 24%. 0% and 33.5%, respectively. This practical and economic approach can be used for developing the algorithms of Chinese ocean color and temperature sensor （COCTS） on the satellite Haiyang-1 to derive the Chl-a concentration concentration distribution. The applicability of the algorithms was analyzed using some in situ measurements. Suspended sediment is the main factor influencing the accuracy of the spectral ratio algorithms of Chl-a concentration. The algorithms are suitable to using in the regions where suspended sediment concentrations （ SSC ） are less than 5 g/m^3 under the condition of relative error of Chl-a concentration retrieval within 35%. High concentration of suspended sediment leads to the overestimate remote sensing retrieval of concentration of Chl-a, while low-middle SSCs lead to the low Chl-a concentration values using the spectral ratio algorithms. Since the accuracy of Chl-a concentration by the spectral ratio algorithms is limited to waters of Case 2, it is necessary to develop semi-analytical models to improve the performance of satellite ocean color remote sensing in turbid coastal waters.

Combining Principal Component Regression and Artificial Neural Network to Predict Chlorophyll-a Concentration of Yuqiao Reservoir’s Outflow

In order to investigate the eutrophication degree of Yuqiao Reservoir, a hybrid method, combining principal component regression (PCR) and artificial neural network (ANN), was adopted to predict chlorophyll-a concentration of Yuqiao Reservoir’s outflow. The data were obtained from two sampling sites, site 1 in the reservoir, and site 2 near the dam. Seven water variables, namely chlorophyll-a concentration of site 2 at time t and that of both sites 10 days before t, total phosphorus(TP), total nitrogen(TN),...

Research on Distribution Regularities of Dust Concentration and Granularity in Large Mining Height Working Face

The key for dust control of coal mine is to clarify the dust concentration distribution and sedimentation in different areas. Both similarity experiment and numerical simulation method have certain restrictions and are quite different from the actual situation on site. In order to study the dust sedimentation regularity of coal mine in large mining height, “filter membrane method” is adopted in this paper, i.e., to dry and weigh the filter membrane before and after sampling, collect the dust of respirable zone on mining face and calculate the dust concentration based on a main airway of 100 m. The result shows that: A large amount of dust will be produced during coal mining, wherein the maximum dust concentration from 6 m upstream to 100 m downstream of coal cutter is 121 mg/m3, while the minimum dust concentration is 61 mg/m3;The dust concentration in return airway is reduced with the distance increases, while the dust concentration at the entrance is 91 mg/m3;A large amount of dust may fall from roof during section advancing and improves the dust concentration of hydraulic support in walking area obviously;The dust granularity of mining face and return airway is 0 - 100 μm, but the amount of respirable dust is higher than 80%, the larger the dust particle size, the higher the dust concentration. Besides, dust in small particle size can be suspended in air flow for longer, but that in large particle size may subside under the action of gravity;To reduce dust exposure, the mining position shall be located in the windward direction of advancing or coal cutter. This research can provide guidance for taking dust prevention measures of working face in large mining height.

Statistical characteristics of chlorophyll-a concentration in Hong Kong's coastal waters

In this paper seven of the ten Water Control Zones (WCZs) in Hong Kong's coastal waters with monthly or bi-weekly sampling data of 17 parameters collected at 37 monitoring stations from 1988 to 1999 were selected to analyze the spatial and temporal variations of chlorophyll-a and its influencing factors. Cluster analysis was employed to group the monitoring stations based on the structure of the data set. Multiple step regression was employed to determine the significant influencing factors of chlorophyll-a level. The results suggest that all the monitoring stations could be grouped into two clusters. Cluster Ⅰ with frequent red tide incidents comprises two WCZs which are semi-enclosed bays. Cluster Ⅱ with less red tide occurrence comprises the other five WCZs in an estuarine environment in the west. For both clusters, the organic contents indicator, BODS, was a common significant influencing factor of the chlorophyll-a level. Nitrogen and light penetration condition related to turbidity, total volatile solids and suspended solids had more influence on the cholophyll-a level in Cluster Ⅰ than in Cluster Ⅱ, while phosphorus and oceanographic conditions associated with salinity, temperature, dissolved oxygen and pH were more important in Cluster Ⅱ than in Cluster Ⅰ. Generally, there was a higher average chlorophyll-a level in winter and autumn in a year. The chlorophyll-a level was much higher in Cluster Ⅰ than in Cluster Ⅱ among all seasons. Although the chlorophyll-a concentration had great variations from place to place in Hong Kong's coastal waters, it seemed to have a common long term fluctuation period of 8-10 years with a high-low-high variation in the period in the whole region, which might be influenced by other factors of global scale.

Rapid Estimation on the Sperm Concentration in Boar Semen by Spectrophotometric Method

[ Objective] To establish the standardized spectrophotometric method to determine boar sperm concentration. [ Method ] The relation- ships between absorbance （A）, transmittance （T） and sperm concentration （C） of different wavelengths （450, 550, 650 nm） were compared. [ Result] The maximum sperm concentration detected by absorbance presented an upward trend with the increase of the wavelengths, 202 mitliorVml （450 nm）, 224 million/ml （550 nm） and 235 mUlion/ml （650 nm）, respectively, but the stability of repeated measurement was decreased. With the increase of sperm dilution times, the stability of repeated measurement of transmittance was reduced, and when dilution times were more than 10 times （450 nm）, 6 times （550 nm） and 4 times （650 nm）, differences appeared between the observed values of repeated measurement. [ Con- clusion] Wavelength at 450 nm was found to be the most sensitive and reliable, and sperm concentration presented cubic functional regression rela- tionship or power functional regression relationship with absorbance or transmittance, respectively. The regression equation for the standard curve at 450 nm was C400 = 0.48A3 - 0.76A2 ＋ 0.67A - 0.066 （ R = 0.951 ） and C400 = 1.657T -0.108. 8 （ R = 0.940）.

The Study of Area-Concentration Fractal Method in Litho-Geochemical Data in Tanurjeh Area, Khorasan Province

Given the scientific progresses as well as the invention of new methods in exploration, it is necessary to conduct some re-investigations in several exploration zones. So, in the present research, geochemical data on Tanurjeh exploration zone, (located in Northern Neishaboor, Khorasane Razavi province) is studied by using some modern statistical methods. Fractal methods are appropriated to study and separate the grades societies in deposits. In this article, litho-geochemical analysis results (ICP) are processed by concentration area fractal method (CA). The distribution diagrams related to the statistical populations are drawn, and anomaly populations of Copper, Gold and Molybdenum are determined besides previous studies (petrography and alteration), the results of statistic methods (CA) and aid presence of the porphyry system in depth.

Applicability of Gravity Separation Method on the Ashashire Gold Ore Deposit from Benishangul Gumuz Region, Western Ethiopia

The study was conducted to determine the applicability of gravity separation method on the Ashashire gold ore deposit Benishangul gumuz region, western Ethiopia. The Ashashire composite was produced to provide sufficient mass for this study and experiment, including sample preparation, mineralogical analysis of gold and associated elements, gravity concentration, and data interpretation and analysis. During the study, a grind optimization was conducted on the composites sample with varying grind size to evaluate the effect of grind size on gold recovery. The ore was moderately ground to the standard grind size of 80%, passing 106 µm, 75 µm, 53 µm and this nominal size was selected for the preliminary assessment for concentration optimization for this deposit. The gravity testing comprised three-stage concentration using Knelson concentrator. High recovery of gold from the gravity concentrates was achieved from the second gravity concentration. Based on the laboratory experimental result analysis, a grind size of P80 75 µm is selected as optimal size for the Ashashire gold deposit. Increasing the grind size from P80 of 75 µm to 106 µm decreases the recovery rate from 75% to 54%, or decreasing the grind size from P80 of 75 µm to 53 µm decreases the gold recovery rate to 37%. The native gold grain in the ores is mostly associated with quartz and fine gold is closely associated with pyrite. According to analysis of the fire assay, chemical, and mineralogical data, only gold and telluride is commercially valuable elements in the ores. Predominantly gold was occurred in the native form of Au-Te. The sample subjected to gravity separation assayed about 2.6 g/t Au.

Synthesize of ZnO Nanorods on Quartz Substrates with Seed Layer via Hydrothermal Method: Influence of Solution Concentration

Vertically oriented ZnO nanorods have been synthesized by hydrothermal method on quartz substrates with a seed layer. The influence of solution concentration on the morphology, structural and optical properties was analyzed. Results indicated that with the increase of solution concentration, the diameter and uniformity of ZnO nanorods increased. And the preferred orientation is obviously which shows better crystal quality. Typically, when the solution concentration is 0.03 mol/L, the nanorods exhibit a stronger UV emission peak located around 380 nm. In the visible region, all synthesized samples demonstrate more than 80% of optical transparency.

Multi-Scale Variation Prediction of PM2.5 Concentration Based on a Monte Carlo Method

Haze concentration prediction,especially PM2.5,has always been a significant focus of air quality research,which is necessary to start a deep study.Aimed at predicting the monthly average concentration of PM2.5 in Beijing,a novel method based on Monte Carlo model is conducted.In order to fully exploit the value of PM2.5 data,we take logarithmic processing of the original PM2.5 data and propose two different scales of the daily concentration and the daily chain development speed of PM2.5 respectively.The results show that these data are both approximately normal distribution.On the basis of the results,a Monte Carlo method can be applied to establish a probability model of normal distribution based on two different variables and random sampling numbers can also be generated by computer.Through a large number of simulation experiments,the average monthly concentration of PM2.5 in Beijing and the general trend of PM2.5 can be obtained.By comparing the errors between the real data and the predicted data,the Monte Carlo method is reliable in predicting the PM2.5 monthly mean concentration in the area.This study also provides a feasible method that may be applied in other studies to predict other pollutants with large scale time series data.

SCATTERING OF FLEXURAL WAVES AND DYNAMIC STRESS CONCENTRATIONS IN MINDLIN'S THICK PLATES WITH A CUTOUT

Using the complex variable method and conformal mapping,scat- tering of flexural waves and dynamic stress concentrations in Mindlin's thick plates with a cutout have been studied.The general solution of the stress problem of the thick plate satisfying the boundary conditions on the contour of cutouts is obtained. Applying the orthogonal function expansion technique,the dynamic stress problem can be reduced into the solution of a set of infinite algebraic equations.As examples, numerical results for the dynamic stress concentration factor in Mindlin's plates with a circular,elliptic cutout are graphically presented in sequence.

Effect of Yb^(3+) concentration on the structures and upconversion luminescence properties of Y_2O_3:Er^(3+) ultrafine phosphors

Y2O3：Er^3＋ ultrafine phosphors with a varying Yb^3＋ ion concentration were prepared by a urea homogeneous precipitation method. The results of XRD show that all the samples are of a pure cubic structure and the average crystallite sizes can be calculated as 45, 34, and 28 nm for Y2O3：Er^3＋ ultrafine phosphors with Yb^3＋ ion concentrations of 0, 10%, and 20%, respectively. The lattice constant and cell volume of the ultrafine phosphors decrease with enhancing Yb^3＋ ion concentration. The upconversion luminescence spectra of all the samples were studied under 980 nm laser excitation. The strong green and red upconversion emission were observed, and attributed to the ^2H11/2→^4I15/2, ^4S3/2 → ^4I15/2 and ^4F9/2 →^4I15/2 transitions of Er^3＋, respectively. The intensity of red emission increases with increasing Yb^3＋ ion concentration. The effect of Yb^3＋ ion concentration on the structures and upconversion luminescence mechanism were discussed.

MULTIPLICITY AND CONCENTRATION BEHAVIOUR OF POSITIVE SOLUTIONS FOR SCHRDINGER-KIRCHHOFF TYPE EQUATIONS INVOLVING THE p-LAPLACIAN IN R^N

In this article, we study the multiplicity and concentration behavior of positive solutions for the p-Laplacian equation of SchrSdinger-Kirchhoff type -εpM（εp-N∫RN｜△u｜p）△pu＋v（x｜u｜p-2u=f（u）in RN, where △p is the p-Laplacian operator, 1 〈 p 〈 N, M ： R＋ → R＋ and V ： RN →R＋ are continuous functions, ε is a positive parameter, and f is a continuous function with subcritical growth. We assume that V satisfies the local condition introduced by M. del Pino and P. Felmer. By the variational methods, penalization techniques, and Lyusternik- Schnirelmann theory, we prove the existence, multiplicity, and concentration of solutions for the above equation.

Particle characteristics and rheological constitutive relations of high concentration red mud

Red mud has relatively small solid particles （d50= 13.02 μm） and will flow in paste form under high pressure during pipeline transport. Red mud belongs to a two-phase flow of materials with high viscosity and a high concentration of non-sedimentation, homogeneous solid-liquids. It is difficult to test its rheological properties under atmospheric pressure. Measurements such as rotational viscometry can not reflect the real state of the material when it is flowing in a pipe. Tested rheological parameters are somewhat higher than the actual values. In our investigation, grain shape, distinctive modality and grain size distribution of red mud were tested. Based on the principle of tube measurement, rheological experiments on red mud at different concentrations were carried out by using our independently developed tube-type pressure theology test facility, and obtained constitutive equations. We conclude that red mud behaves as non-Newtonian pseudo-plastic fluid in pipe flows. Its consistency and power-law indices vary considerably with different concentrations.

Effect of Surface Topography on Stress Concentration Factor

Neuber rule and Arola-Ramulu model are widely used to predict the stress concentration factor of rough specimens. However, the height parameters and effective valley radius used in these two models depend strongly on the resolution of the roughness-measuring instruments and are easily introduce measuring errors. Besides, it is difficult to find a suitable parameter to characterize surface topography to quantitatively describe its effect on stress concentration factor. In order to overcome these disadvantages, profile moments are carried out to characterize surface topography, surface topography is simulated by superposing series of cosine components, the stress concentration factors of different micro cosine-shaped surface topographies are investigated by finite element analysis. In terms of micro cosine-shaped surface topography, an equation using the second profile moment to estimate the stress concentration factor is proposed, predictions for the stress concentration factor using the proposed expression are within 10% error compared with the results of finite element analysis, which are more accurate than other models. Moreover, the proposed equation is applied to the real surface topography machined by turning. Predictions for the stress concentration factor using the proposed expression are within 10% of the maximum stress concentration factors and about 5% of the effective stress concentration factors estimated from the finite element analysis for three levels of turning surface topographies under different simulated scales. The proposed model is feasible in predicting the stress concentration factors of real machined surface topographies.

AN ANALYSIS FOR DIFFRACTION OF FLEXURAL WAVES AND DYNAMIC STRESS CONCENTRATIONS IN THICK PLATES WITH A CAVITY

By using the complex variable method and conformal mapping, the diffraction of flexural waves and dynamic stress concentrations in thick plates with a cavity have been studied. A general solution of the stress problem of the thick plate satisfying the boundary conditions on the contour of an arbitrary cavity is obtained. By employing the orthogonal function expansion technique, the dynamic stress problem can be reduced to the solution of an infinite algebraic equation series. As an example, the numerical results for the dynamic stress concentration factor in thick plates with a circular, elliptic cavity are graphically presented. The numerical results are discussed.

DYNAMIC STRESS CONCENTRATIONS IN AMBARTSUMIAN'S PLATE WITH A CUTOUT

Based on the motion equations of flexural wave in Ambartsumian' s plates including the effects of transverse shear deformations,by using perturbation method of small parameter,the scatter- ing of flexural waves and dynamic stress concentrations in the plate with a cutout have been studied. The asypmtotic solution of the dynamic stress problem is obtained.Numerical results for the dynamic stress concentration factor in Ambartsumian's plates with a circular cutout are graphically presented and discussed.

Stress concentration factor expression for tension strip with eccentric elliptical hole

Two explicit expressions of the stress concentration factor for a tension finite-width strip with a central elliptical hole and an eccentric elliptical hole, respectively, are formulated by using a semi-analytical and semi-empiricai method. Accuracy of the results obtained from these expressions is better, and application scope is wider, than the results of Durelli＇s photo-elastic experiment and Isida＇s formula. When eccentricity of the elliptical hole is within a certain range, the error is less than 8%. Based on the relation between the stress concentration factor and the stress intensity factor, a stress intensity factor expression for tension strips with a center or an eccentric crack is derived with the obtained stress concentration factor expressions. Compared with the existing formulae and the finite element analysis, this stress intensity factor expression also has sufficient accuracy.