A well-known hazardous metal and top contaminant in wastewater is hexavalent chromium. The two forms of most commonly found chromium are chromate ( CrO 4 2− ) and dichromate ( Cr 2 O 7 2− ). Leather tanning, cooling t...A well-known hazardous metal and top contaminant in wastewater is hexavalent chromium. The two forms of most commonly found chromium are chromate ( CrO 4 2− ) and dichromate ( Cr 2 O 7 2− ). Leather tanning, cooling tower blow-down, plating, electroplating, rinse water sources, anodizing baths etc. are the main sources of Cr (VI) contamination. The Cr (VI) is not only non-biodegradable in the environment but also carcinogenic to living population. It is still difficult to treat Cr contaminated waste water effectively, safely, eco-friendly, and economically. As a result, many techniques have been used to treat Cr (VI)-polluted wastewater, including adsorption, chemical precipitation, coagulation, ion-exchange, and filtration. Among these practices, the most practical method is adsorption for the removal of Cr (VI) from aqueous solutions, which has gained widespread acceptance due to the ease of use and affordability of the equipment and adsorbent. It has been revealed that Fe-based adsorbents’ oxides and hydroxides have high adsorptive potential to lower Cr (VI) content below the advised threshold. Fe-based adsorbents were also discovered to be relatively cheap and toxic-free in Cr (VI) treatment. Fe-based adsorbents are commonly utilized in industry. It has been discovered that nanoparticles of Fe-, Ti-, and Cu-based adsorbents have a better capacity to remove Cr (VI). Cr (VI) was effectively removed from contaminated water using mixed element-based adsorbents (Fe-Mn, Fe-Ti, Fe-Cu, Fe-Zr, Fe-Cu-Y, Fe-Mg, etc.). Initial findings suggest that Cr (VI) removal from wastewater may be accomplished by using magnesium ferrite nanomaterials as an efficient adsorbent.展开更多
A biochar-supported green nZVI(G-nZVI@MKB)composite was synthesized using mango kernel waste with“dual identity”as reductant and biomass of biochar.The G-nZVI@MKB with a Fe/C mass ratio of 2.0(G-nZVI@MKB2)was determ...A biochar-supported green nZVI(G-nZVI@MKB)composite was synthesized using mango kernel waste with“dual identity”as reductant and biomass of biochar.The G-nZVI@MKB with a Fe/C mass ratio of 2.0(G-nZVI@MKB2)was determined as the most favorable composite for hexavalent chromium(Cr(VI))removal.Distinct influencing parameters were discussed,and 99.0%of Cr(VI)removal occurred within 360 min under these optimized parameters.Pseudo-second order kinetic model and intra-particle diffusion model well depicted Cr(VI)removal process.The XRD,FTIR,SEM,and XPS analyses verified the key roles of G-nZVI and functional groups,as well as the primary removal mechanisms involving electrostatic attraction,reduction,and complexation.G-nZVI@MKB2 exhibited good stability and reusability with only a 16.4%decline in Cr(VI)removal after five cycles.This study offered evidence that mango kernel could be recycled as a beneficial resource to synthesize green nZVI-loaded biochar composite for efficient Cr(VI)elimination from water.展开更多
Metal trace elements (MTE) are among the most harmful micropollutants of natural waters. Eliminating them helps improve the quality and safety of drinking water and protect human health. In this work, we used mango ke...Metal trace elements (MTE) are among the most harmful micropollutants of natural waters. Eliminating them helps improve the quality and safety of drinking water and protect human health. In this work, we used mango kernel powder (MKP) as bioadsorbent material for removal of Cr (VI) from water. Uv-visible spectroscopy was used to monitor and quantify Cr (VI) during processing using the Beer-Lambert formula. Some parameters such as pH, mango powder, mass and contact time were optimized to determine adsorption capacity and chromium removal rate. Adsorption kinetics, equilibrium, isotherms and thermodynamic parameters such as ΔG˚, ΔH˚, and ΔS˚, as well as FTIR were studied to better understand the Cr (VI) removal process by MKP. The adsorption capacity reached 94.87 mg/g, for an optimal contact time of 30 min at 298 K. The obtained results are in accordance with a pseudo-second order Freundlich adsorption isotherm model. Finally FTIR was used to monitor the evolution of absorption bands, while Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS) were used to evaluate surface properties and morphology of the adsorbent.展开更多
Phosphorus fertilizers from less pure sedimentary sources become increasingly important, due to depletion of phosphorus from igneous rock of high quality. Consequently, robust methods with potential to remove various ...Phosphorus fertilizers from less pure sedimentary sources become increasingly important, due to depletion of phosphorus from igneous rock of high quality. Consequently, robust methods with potential to remove various types of hazardous elements are required. Among such impurities, hexavalent chromium (Cr(VI)) is very likely to become a future challenge. Different industrial ways to treat phosphate rock are currently being practised, and we have here studied how chromium behaves when using the nitro-phosphate process. The reduction mechanism of Cr (VI) in nitric acid and phosphoric acid solutions was investigated by measuring redox potential and UV-VIS spectra. The results show that Cr (VI) is not stable in strong nitric acid solutions. Reduction of Cr (VI) species decreased with decreasing temperature, NO<sub>2</sub> concentration, ionic strength and absence of light. These findings support the proposed reduction reaction:The reduction rate was observed proportional to the nitric acid decomposition: .展开更多
Lignocellulose has the potential to become a bio-based adsorbent due to its biodegradability and renewability.In this study,a novel polydopamine functionalized-lignin(lignin@PDA),prepared via self-polymerization of do...Lignocellulose has the potential to become a bio-based adsorbent due to its biodegradability and renewability.In this study,a novel polydopamine functionalized-lignin(lignin@PDA),prepared via self-polymerization of dopamine(PDA)on lignin,was used as a bio-based adsorbent for rapid scavenging of hexavalent chromium(Cr(VI)).The morphology,functional groups,crystalline structure,and chemical composition of lignin@PDA were characterized with a scanning electron microscope-energy dispersive spectrometer,Fourier transform infrared spectroscopy,X-ray diffraction,and X-ray photoelectron spectroscopy.The Cr(VI)adsorption process of lignin@PDA was studied using batch experiments as a function of pH,ionic strength,adsorbent dose,and contact time at room temperature.The adsorption rate of lignin@PDA was five times greater than that of the unmodified lignin,with a maximum adsorption capacity of 102.6 mg/g in an acidic medium.The adsorption of Cr(VI)on lignin@PDA fit the pseudo-secondorder equation and the Freundlich model,indicating that the adsorption process was mainly dominated by chemisorption and surface complexation.The thermodynamic parameters showed that adsorption of Cr(VI)on lignin@PDA was an endothermic and spontaneous process.The X-ray absorption fine structure results showed that sorption and reduction of Cr(VI)into Cr(II)occurred simultaneously on lignin.Moreover,PDA coating not only improved the reactivity of lignin but also promoted the complete reduction of Cr(VI)by lignin.According to these results,polydopamine functionalized-lignin is a promising bio-based adsorbent for immobilization of Cr(VI)from wastewater.展开更多
Up to 1.5wt%of Cr(Ⅲ)salts(CrCl_(3),and Cr_(2)O_(3))and Cr(Ⅵ)salts(Na_(2)CrO_(4),and CaCr_(2)O_(7))were incorporated into red mud-based geopolymers,respectively.The solidification/stabilization,compressive strength,a...Up to 1.5wt%of Cr(Ⅲ)salts(CrCl_(3),and Cr_(2)O_(3))and Cr(Ⅵ)salts(Na_(2)CrO_(4),and CaCr_(2)O_(7))were incorporated into red mud-based geopolymers,respectively.The solidification/stabilization,compressive strength,and durability of the Cr-containing geopolymers were investigated.The experimental results indicate that the red mud-based geopolymer could effectively solidify/stabilize different types of Cr salts with solidification/stabilization rates of above 99.61%.Geopolymers are environmentally safe when the dosage of CaCr_(2)O_(7)is≤1.0wt%,or the dosage of CrCl_(3),Cr_(2)O_(3),and Na_(2)CrO_(4)is≤1.5wt%,respectively.The effects of Cr salts on the compressive strength varies with the type and content of Cr salts.The freeze-thaw cycle is more destructive to geopolymer properties than sulfate attack or acid rain erosion.The solidification/stabilization of Cr is mainly attributed to the following reasons:a)The chemical binding of Cr is related to the formation of Cr-containing hydrates(eg,magnesiochromite((Mg,Fe)(Cr,Al)_(2)O_(4)))and doping into N-A-S-H gel and C-A-S-H gel framework;b)The physical effect is related to the encapsulation by the hydration products(e g,N-A-S-H gel and C-A-S-H gel).This study provides a reference for the treatment of hazardous Cr-containing wastes by solid waste-based geopolymers.展开更多
Chromium plays a vital role in stainless steel due to its ability to improve the corrosion resistance of the latter.However,the re-lease of chromium from stainless steel slag(SSS)during SSS stockpiling causes detrimen...Chromium plays a vital role in stainless steel due to its ability to improve the corrosion resistance of the latter.However,the re-lease of chromium from stainless steel slag(SSS)during SSS stockpiling causes detrimental environmental issues.To prevent chromium pollution,the effects of iron oxide on crystallization behavior and spatial distribution of spinel were investigated in this work.The results revealed that FeO was more conducive to the growth of spinels compared with Fe2O3 and Fe3O4.Spinels were found to be mainly distrib-uted at the top and bottom of slag.The amount of spinel phase at the bottom decreased with the increasing FeO content,while that at the top increased.The average particle size of spinel in the slag with 18wt%FeO content was 12.8μm.Meanwhile,no notable structural changes were observed with a further increase in FeO content.In other words,the spatial distribution of spinel changed when the content of iron oxide varied in the range of 8wt%to 18wt%.Finally,less spinel was found at the bottom of slag with a FeO content of 23wt%.展开更多
It is quite important to ensure the safety and sustainable development of nuclear energy for the treatment of radioactive wastewater. To treat radioactive wastewater efficiently and rapidly, two multi-amine β-cyclode...It is quite important to ensure the safety and sustainable development of nuclear energy for the treatment of radioactive wastewater. To treat radioactive wastewater efficiently and rapidly, two multi-amine β-cyclodextrin polymers(diethylenetriamine β-cyclodextrin polymer(DETA-TFCDP) and triethylenetetramine β-cyclodextrin polymer(TETA-TFCDP)) were prepared and applied to capture uranium. Results exhibited that DETA-TFCDP and TETA-TFCDP displayed the advantages of high adsorption amounts(612.2and 628.2 mg·g-1, respectively) and rapid adsorption rates, which can reach(88 ± 1)% of their equilibrium adsorption amounts in 10 min. Moreover, the adsorbent processes of DETA-TFCDP and TETATFCDP on uranium(Ⅵ) followed the Langmuir model and pseudo-second-order model, stating they were mainly chemisorption and self-endothermic. Besides, TETA-TFCDP also showed excellent selectivity in the presence of seven competing cations and could be effectively reused five times via Na2CO3as the desorption reagent. Meanwhile, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy illustrated that the enriched multi-amine groups and oxygen-containing functional groups on the surface of TETA-TFCDP were the main active sites for capturing uranium(Ⅵ). Hence, multi-amine β-cyclodextrin polymers are a highly efficient, rapid, and promising adsorbent for capturing uranium(Ⅵ)from radioactive wastewater.展开更多
文摘A well-known hazardous metal and top contaminant in wastewater is hexavalent chromium. The two forms of most commonly found chromium are chromate ( CrO 4 2− ) and dichromate ( Cr 2 O 7 2− ). Leather tanning, cooling tower blow-down, plating, electroplating, rinse water sources, anodizing baths etc. are the main sources of Cr (VI) contamination. The Cr (VI) is not only non-biodegradable in the environment but also carcinogenic to living population. It is still difficult to treat Cr contaminated waste water effectively, safely, eco-friendly, and economically. As a result, many techniques have been used to treat Cr (VI)-polluted wastewater, including adsorption, chemical precipitation, coagulation, ion-exchange, and filtration. Among these practices, the most practical method is adsorption for the removal of Cr (VI) from aqueous solutions, which has gained widespread acceptance due to the ease of use and affordability of the equipment and adsorbent. It has been revealed that Fe-based adsorbents’ oxides and hydroxides have high adsorptive potential to lower Cr (VI) content below the advised threshold. Fe-based adsorbents were also discovered to be relatively cheap and toxic-free in Cr (VI) treatment. Fe-based adsorbents are commonly utilized in industry. It has been discovered that nanoparticles of Fe-, Ti-, and Cu-based adsorbents have a better capacity to remove Cr (VI). Cr (VI) was effectively removed from contaminated water using mixed element-based adsorbents (Fe-Mn, Fe-Ti, Fe-Cu, Fe-Zr, Fe-Cu-Y, Fe-Mg, etc.). Initial findings suggest that Cr (VI) removal from wastewater may be accomplished by using magnesium ferrite nanomaterials as an efficient adsorbent.
基金supported by the National Natural Science Foundation of China(51808253)the Science and Technology Planning Project of Jilin Province(20220508008RC)+1 种基金Science and Technology Project of Jilin Provincial Education Department(JJKH20220295KJ and JJKH20210272KJ)the Science and Technology Projects of the Ministry of Housing and Urban-Rural Development(2018-K6-003).
文摘A biochar-supported green nZVI(G-nZVI@MKB)composite was synthesized using mango kernel waste with“dual identity”as reductant and biomass of biochar.The G-nZVI@MKB with a Fe/C mass ratio of 2.0(G-nZVI@MKB2)was determined as the most favorable composite for hexavalent chromium(Cr(VI))removal.Distinct influencing parameters were discussed,and 99.0%of Cr(VI)removal occurred within 360 min under these optimized parameters.Pseudo-second order kinetic model and intra-particle diffusion model well depicted Cr(VI)removal process.The XRD,FTIR,SEM,and XPS analyses verified the key roles of G-nZVI and functional groups,as well as the primary removal mechanisms involving electrostatic attraction,reduction,and complexation.G-nZVI@MKB2 exhibited good stability and reusability with only a 16.4%decline in Cr(VI)removal after five cycles.This study offered evidence that mango kernel could be recycled as a beneficial resource to synthesize green nZVI-loaded biochar composite for efficient Cr(VI)elimination from water.
文摘Metal trace elements (MTE) are among the most harmful micropollutants of natural waters. Eliminating them helps improve the quality and safety of drinking water and protect human health. In this work, we used mango kernel powder (MKP) as bioadsorbent material for removal of Cr (VI) from water. Uv-visible spectroscopy was used to monitor and quantify Cr (VI) during processing using the Beer-Lambert formula. Some parameters such as pH, mango powder, mass and contact time were optimized to determine adsorption capacity and chromium removal rate. Adsorption kinetics, equilibrium, isotherms and thermodynamic parameters such as ΔG˚, ΔH˚, and ΔS˚, as well as FTIR were studied to better understand the Cr (VI) removal process by MKP. The adsorption capacity reached 94.87 mg/g, for an optimal contact time of 30 min at 298 K. The obtained results are in accordance with a pseudo-second order Freundlich adsorption isotherm model. Finally FTIR was used to monitor the evolution of absorption bands, while Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS) were used to evaluate surface properties and morphology of the adsorbent.
文摘Phosphorus fertilizers from less pure sedimentary sources become increasingly important, due to depletion of phosphorus from igneous rock of high quality. Consequently, robust methods with potential to remove various types of hazardous elements are required. Among such impurities, hexavalent chromium (Cr(VI)) is very likely to become a future challenge. Different industrial ways to treat phosphate rock are currently being practised, and we have here studied how chromium behaves when using the nitro-phosphate process. The reduction mechanism of Cr (VI) in nitric acid and phosphoric acid solutions was investigated by measuring redox potential and UV-VIS spectra. The results show that Cr (VI) is not stable in strong nitric acid solutions. Reduction of Cr (VI) species decreased with decreasing temperature, NO<sub>2</sub> concentration, ionic strength and absence of light. These findings support the proposed reduction reaction:The reduction rate was observed proportional to the nitric acid decomposition: .
基金supported by the Zhejiang Provincial Natural Science Foundation of China(Grant No.LQ19E030017)the Research Start-up Fund(Grant No.KYS205619042)the Technological Research Project for Public Welfare of Zhejiang Province(Grant No.LGG19E030005).
文摘Lignocellulose has the potential to become a bio-based adsorbent due to its biodegradability and renewability.In this study,a novel polydopamine functionalized-lignin(lignin@PDA),prepared via self-polymerization of dopamine(PDA)on lignin,was used as a bio-based adsorbent for rapid scavenging of hexavalent chromium(Cr(VI)).The morphology,functional groups,crystalline structure,and chemical composition of lignin@PDA were characterized with a scanning electron microscope-energy dispersive spectrometer,Fourier transform infrared spectroscopy,X-ray diffraction,and X-ray photoelectron spectroscopy.The Cr(VI)adsorption process of lignin@PDA was studied using batch experiments as a function of pH,ionic strength,adsorbent dose,and contact time at room temperature.The adsorption rate of lignin@PDA was five times greater than that of the unmodified lignin,with a maximum adsorption capacity of 102.6 mg/g in an acidic medium.The adsorption of Cr(VI)on lignin@PDA fit the pseudo-secondorder equation and the Freundlich model,indicating that the adsorption process was mainly dominated by chemisorption and surface complexation.The thermodynamic parameters showed that adsorption of Cr(VI)on lignin@PDA was an endothermic and spontaneous process.The X-ray absorption fine structure results showed that sorption and reduction of Cr(VI)into Cr(II)occurred simultaneously on lignin.Moreover,PDA coating not only improved the reactivity of lignin but also promoted the complete reduction of Cr(VI)by lignin.According to these results,polydopamine functionalized-lignin is a promising bio-based adsorbent for immobilization of Cr(VI)from wastewater.
基金Funded by the National Natural Science Foundation of China(Nos.52074245,52374416 and 52202029)the China Postdoctoral Science Foundation(No.2022M721058)。
文摘Up to 1.5wt%of Cr(Ⅲ)salts(CrCl_(3),and Cr_(2)O_(3))and Cr(Ⅵ)salts(Na_(2)CrO_(4),and CaCr_(2)O_(7))were incorporated into red mud-based geopolymers,respectively.The solidification/stabilization,compressive strength,and durability of the Cr-containing geopolymers were investigated.The experimental results indicate that the red mud-based geopolymer could effectively solidify/stabilize different types of Cr salts with solidification/stabilization rates of above 99.61%.Geopolymers are environmentally safe when the dosage of CaCr_(2)O_(7)is≤1.0wt%,or the dosage of CrCl_(3),Cr_(2)O_(3),and Na_(2)CrO_(4)is≤1.5wt%,respectively.The effects of Cr salts on the compressive strength varies with the type and content of Cr salts.The freeze-thaw cycle is more destructive to geopolymer properties than sulfate attack or acid rain erosion.The solidification/stabilization of Cr is mainly attributed to the following reasons:a)The chemical binding of Cr is related to the formation of Cr-containing hydrates(eg,magnesiochromite((Mg,Fe)(Cr,Al)_(2)O_(4)))and doping into N-A-S-H gel and C-A-S-H gel framework;b)The physical effect is related to the encapsulation by the hydration products(e g,N-A-S-H gel and C-A-S-H gel).This study provides a reference for the treatment of hazardous Cr-containing wastes by solid waste-based geopolymers.
基金the National Natural Science Foundation of China(Nos.52074078 and 52374327)the Applied Fundamental Research Program of Liaoning Province(No.2023JH2/101600002)+2 种基金the Shenyang Young Middle-Aged Scientific and Technological Innovation Talent Support Program(No.RC220491)the Liaoning Province Steel Industry-University-Research Innovation Alliance Cooperation Project of Bensteel Group(No.KJBLM202202)the Fundamental Research Funds for the Central Universities(Nos.N2201023 and N2325009).
文摘Chromium plays a vital role in stainless steel due to its ability to improve the corrosion resistance of the latter.However,the re-lease of chromium from stainless steel slag(SSS)during SSS stockpiling causes detrimental environmental issues.To prevent chromium pollution,the effects of iron oxide on crystallization behavior and spatial distribution of spinel were investigated in this work.The results revealed that FeO was more conducive to the growth of spinels compared with Fe2O3 and Fe3O4.Spinels were found to be mainly distrib-uted at the top and bottom of slag.The amount of spinel phase at the bottom decreased with the increasing FeO content,while that at the top increased.The average particle size of spinel in the slag with 18wt%FeO content was 12.8μm.Meanwhile,no notable structural changes were observed with a further increase in FeO content.In other words,the spatial distribution of spinel changed when the content of iron oxide varied in the range of 8wt%to 18wt%.Finally,less spinel was found at the bottom of slag with a FeO content of 23wt%.
基金National Natural Science Foundation of China(21603064,52102214)Natural Science Foundation of Jiangxi Province(20202BABL203026,20212BAB203001,20202BABL214016)College Student Innovation and Enterprise Programme of Jiangxi Province(S202310405010)provided funding for this study.
文摘It is quite important to ensure the safety and sustainable development of nuclear energy for the treatment of radioactive wastewater. To treat radioactive wastewater efficiently and rapidly, two multi-amine β-cyclodextrin polymers(diethylenetriamine β-cyclodextrin polymer(DETA-TFCDP) and triethylenetetramine β-cyclodextrin polymer(TETA-TFCDP)) were prepared and applied to capture uranium. Results exhibited that DETA-TFCDP and TETA-TFCDP displayed the advantages of high adsorption amounts(612.2and 628.2 mg·g-1, respectively) and rapid adsorption rates, which can reach(88 ± 1)% of their equilibrium adsorption amounts in 10 min. Moreover, the adsorbent processes of DETA-TFCDP and TETATFCDP on uranium(Ⅵ) followed the Langmuir model and pseudo-second-order model, stating they were mainly chemisorption and self-endothermic. Besides, TETA-TFCDP also showed excellent selectivity in the presence of seven competing cations and could be effectively reused five times via Na2CO3as the desorption reagent. Meanwhile, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy illustrated that the enriched multi-amine groups and oxygen-containing functional groups on the surface of TETA-TFCDP were the main active sites for capturing uranium(Ⅵ). Hence, multi-amine β-cyclodextrin polymers are a highly efficient, rapid, and promising adsorbent for capturing uranium(Ⅵ)from radioactive wastewater.
