Equation of Radiation Heat Transfer in Multiple Combustion Boiler Furnace of Fluidized Bed and Pulverized Coal Firing

The equation for radiation heat transfer in a multiple combustion boiler furnace with nuidized bed and pulverized coal firing is derived from direct calculation of radiation heat transfer.

Compatibility of Fly Ash and Slag from Circulating Fluidized Bed Boiler for Concrete Beam

The applications of fly ash and slag from circulating fluidized bed boiler were studied as mineral admixture and aggregate for steel reinforced concrete beam.The results show that the concrete beam with fly ash and slag from circulating fluidized bed boilers has a similar ultimate cracking load coefficient as the ordinary cement concrete and a higher bending moment limit.Under the same load,it has a smaller deformation than the ordinary concrete.

Effects of particle type on the particle fluidization and distribution in a liquid–solid circulating fluidized bed boiler

A liquid-solid circulating fluidized bed boiler is designed and built for visualization research by applying the fluidized bed heat transfer and fouling prevention technology to the water side of the boiler. Four types of engineering plastic particles with different physical properties are selected as the solid working media. The effect of particle types on the fluidization and distribution of particles in the boiler is investigated under different feedwater flow rates and amount of added particles by using the charge couple device image measurement and acquisition system. The results show that all kinds of particles can't be normally fluidized and accumulate in the drum at low amount of added particles and feedwater flow rate. The particles with great density and low sphericity are more likely to accumulate. The average solid holdup in the riser tubes increases with the increase in feedwater flow rate and the amount of added particles. The non-uniform degree of particle distribution in the riser tubes generally decreases with the increase in feedwater flow rate and the amount of added particles. The particles with small density and settling velocity have high average solid holdup in the riser tubes under close sphericity. In generally,the smaller the density and settling velocity, the more uniform the particle distribution in the riser tubes.Three-dimensional diagrams of the non-uniform degree of particle distribution in the riser tubes of the boiler are established.

Model prediction of the operating behavior of a circulating fluidized bed boiler

An improved mathematical model for a circulating fluidized bed (CFB) boiler based on the model developed earlier by the authors was applied to simulate the operation of a 12 MW CFB boiler. The influences of the excess air ratio, primary air ratio, coal particle size distribution, coal properties (ash content and volatile content) and Ca/S ratio on the boiler operation were analyzed. The results showed that the model simulation may be applied to the optimum design and economic operation of the CFB boiler.

Hardening Properties of Foamed Concrete with Circulating Fluidized Bed Boiler Ash, Blast Furnace Slag, and Desulfurization Gypsum as the Binder

Recently, a large amount of circulating fluidized bed boiler ash (CFBA) and desulfurization gypsum (DSG) has been produced, and it is essential to develop technology to utilize them. These materials have CaO and SO3, which are considered to be a stimulant for blast furnace slag (BFS). This study presents an experimental investigation of the compressive strength and heavy metal ions immobilization properties of cement-free materials comprising CFBA, BFS, and DSG. The feasibility of manufacturing foamed concrete using these materials was examined, and field test of foamed concrete was conducted. Experimentally, the flow, compressive strength, and heavy metal ions concentration were evaluated via inductively coupled plasma atomic emission spectroscopy (ICP-AES) of the paste and foamed concrete. The experimental investigation revealed the self-healing hardening ability of fluidized bed boiler ash. In addition, the compressive strength was increased with the increasing replacement rates of BFS and DSG in the CFBA paste, and the compressive strength of 14.6 - 17.2 MPa was recorded over 28 days of curing. From the result obtained, the feasibility of manufacturing foamed concrete with a foam volume of 120 L, incorporating the aforementioned materials, is confirmed. It was also found that after 28 days of age, a 7.9-MPa compressive strength of the foamed concrete was attained, and heavy metal ions elution in this foamed concrete was also significantly reduced. Therefore, CFBA, BFS, and DSG could be used as a binder for the foamed concrete.

超临界循环流化床锅炉深度调峰时水冷壁流动不稳定特性计算分析

针对深度调峰时超临界循环流化床锅炉水冷壁管道内的汽液两相流动不稳定问题,提出了一种适用于不同工况的频域法数学模型。通过对质量、能量、动量方程进行小扰动线性化后经拉普拉斯变换得到了用于描述管道内汽液流体流动稳定性的传递函数,通过图解奈奎斯特图的方法判断管内工质流动的稳定性。然后,通过该模型计算了某350 MW超临界循环流化床锅炉水冷壁管段的不稳定边界并研究了不同参数对流动不稳定特性的影响。计算结果表明:所选回路在20%和50%锅炉最大连续蒸发量负荷发生流动不稳定时,热负荷分别为76.09 kW·m^(-2)和113.52 kW·m^(-2),水冷壁管道流动稳定且安全;入口过冷度对临界热流密度的影响呈非单值性;增大质量流速使流体的进口和出口密度差减小,有利于流动的稳定;增大入口节流系数,可以抑制入口处流量的脉动,有利于流动的稳定;在不同的工况条件下,改变管段倾斜角度会对流动稳定性产生不同的影响。

生物质锅炉屏式过热器弯曲变形原因分析

针对某电厂40MW机组生物质循环流化床锅炉在启动初期高温过热器管屏出现严重变形的原因进行分析,认为锅炉在启动初期减温水喷水量过大,造成高温过热器管屏中蒸汽带水,高温过热器管屏璧温偏差波动大,进而导致管屏弯曲变形。针对此种问题,建议运行人员在锅炉启动初期,严格控制减温水的喷水量,同时,快速通过锅炉启动初期阶段,避免管屏弯曲问题。

300 MW循环流化床锅炉SNCR脱硝仿真模拟

针对某300 MW循环流化床锅炉SNCR脱硝过程进行CFD仿真模拟,获得了锅炉出口到旋风分离器出口的速度和氨浓度分布及变化规律。结果显示:烟气进入旋风分离器后被快速加速,最高速度达110 m/s,并呈中心区速度低、靠近壁面区速度高的趋势;尿素溶液经喷枪喷入烟道后,快速蒸发为氨气,并在整个旋风分离器内迅速扩散。随着喷射速度的增加,整个反应区内的氨浓度增加,当喷射速度从60 m/s增加至90 m/s的过程中,氨浓度分布规律发生变化。

60 MW循环流化床锅炉水冷壁泄漏原因分析

旨在分析某热电厂2号循环流化床锅炉水冷壁管泄漏的原因。通过宏观检查、金相检查及拉伸试验等方法,对泄漏管样及对比管样的焊接质量、组织状态及力学性能进行了全面检测。宏观检查发现,泄漏管样及一处对比管样堆焊处存在焊接裂纹及局部焊瘤,表明焊接时电流过大导致母材过热熔化;金相检查进一步证实了过烧组织的形成及焊接裂纹的扩展路径;拉伸试验结果表明,未泄漏管样的力学性能符合标准要求。泄漏原因为水冷壁管表面堆焊时焊接电流过大,导致母材过烧并产生焊接裂纹。

CFB锅炉燃烧过程优化控制系统技术改造研究

用无辨识自适应预估控制技术对循环流化床锅炉燃烧过程进行优化,及时、准确对主汽压力、主汽温度、炉膛压力、给煤、一次风机、二次风机、引风机、断煤处理、床压进行自动控制,实现了燃烧过程自动控制和过程优化,使运行更加平稳。减少煤耗1%以上,经济效益明显,实现了节能降耗减碳的目标。

超超临界循环流化床锅炉技术研发进展

随着技术进步和对节能减排需求的提升,更先进的超超临界循环流化床(circulating fluidized bed,CFB)锅炉技术成为行业发展趋势。该文探讨了超超临界CFB锅炉技术的设计理念,包括流态化燃烧、水动力系统、污染物控制及系统集成等关键技术。分析大尺寸炉膛内流态化燃烧的均匀性和燃尽性问题,探讨了不同炉型燃烧系统设计;研究超超临界压力下低质量流速垂直管圈水动力系统的设计方案;提出在大截面和高炉膛条件下污染物控制的设计思路;通过对锅炉燃烧技术、热力系统及辅助系统的耦合特性分析,指出燃烧侧与蒸汽侧系统设计的优化方向。基于对关键技术的深入研究和超临界CFB锅炉的实践经验,形成了多种超超临界CFB技术方案,多个采用不同技术方案的项目已进入到工程应用阶段,其中可靠、灵活、清洁和高效是设计中的关键考量。期望这些多样化的超超临界CFB技术路线能够在未来发展中展现出灵活性和低碳优势。

燃煤锅炉改燃兰炭燃烧工艺及效益分析

兰炭因热值高、硫含量低的特点被广泛应用于散煤替代,燃煤锅炉改燃兰炭是实现资源合理利用、降低污染物排放和改善企业经济效益的有效途径。以河北某循环流化床锅炉改燃兰炭工程为例,燃烧系统采用掺烧灰渣的方法,解决改燃后机械未完全燃烧导致损失大和物料循环不稳定问题,确定了兰炭和灰渣的最佳掺混比为9∶1;配风系统采用控制总量并降低一次风率的方法,解决兰炭着火困难的问题,确定了最佳一次风比例为55%;换热系统采用增加锅炉尾部受热面的方法,解决因燃料热值提升较大产生的蒸汽超温和锅炉效率下降问题。改燃扩容后锅炉烟尘、SO2和NOx排放分别比原锅炉降低了73%、94%和55%,以原锅炉35 t/h的额定功率运行,每小时节约燃料成本5.51%,产吨蒸汽所需燃料成本降低6.47元。

基于TF-NGO算法的CFB锅炉床温系统建模研究

床温是循环流化床(CFB)锅炉重要的运行参数之一。针对床温耦合性强、干扰因素多、控制复杂的问题,亟需建立床温的数学模型,以实现床温控制,从而保证CFB锅炉安全、平稳地运行。为此,首先引入了混沌映射、切线飞行(TF)和柯西变异策略改进北方苍鹰优化(NGO)算法,并用实际工况的系统模型测试TF-NGO算法。测试结果表明,TF-NGO算法拥有更快的收敛速度和更高的寻优精度。其次,采集并预处理山西某电厂350 MW超临界CFB锅炉的现场运行数据。最后,采用TF-NGO算法对所建模型的参数进行辨识,并用实际工况数据进行模型验证。辨识和验证结果表明,由TF-NGO算法辨识的床温模型与实际输出拟合度高,能有效反映床温的动态特性,证明所建模型的有效性。该研究为后续对350 MW超临界CFB锅炉床温的优化控制研究奠定了基础。

240t/h循环流化床锅炉深度灵活调峰工程示范

煤电深度灵活调峰是促进可再生能源电力消纳、减少CO_(2)排放的重要举措。但燃煤锅炉深度灵活调峰存在负荷下调深度受限和NO_(x)排放高的技术难题。本文首次采用循环流化床耦合煤粉预热的技术路线,改建了现役240 t/h高温高压循环流化床锅炉,试验结果表明,锅炉负荷调节深度降低18%,且实现了零喷氨超低NO_(x)排放。240 t/h循环流化床锅炉深度灵活调峰工程示范的成功运行,为燃煤电站深度灵活调峰技术的发展提供了支撑。

循环流化床锅炉降低灰渣含碳量热态试验研究

针对循环流化床(CFB)锅炉燃用非设计煤种工况下,对总风量、一/二次风比例、床温、床压等参数进行热态调整试验,分析各参数对锅炉飞灰及底渣含碳量的影响规律。结果表明:在330 t/h负荷的基准工况下(不投飞灰再循环),通过适当提升床压及燃烧室温度,能使燃料充分燃烧,飞灰含碳量由调整前最高20.75%减少到15.97%左右,底渣含碳量从最高2.28%降低至0.40%左右,锅炉效率提高约1.5%以上。此外,飞灰再循环的投入能有效降低飞灰含碳量,建议在生产实践中尽量保证飞灰再循环的连续投入。

330 MW循环流化床锅炉深度调峰技术

为推进“双碳”政策的实施,消纳波动性较强的新能源并网发电,当前对火电机组的深度调峰要求越来越高。循环流化床(circulating fluidized bed,CFB)锅炉机组在深度调峰低负荷运行工况有着先天优势,但实现20%以下的超低负荷运行依然面临众多的困难,如炉内流化的稳定性、氮氧化物的排放及炉内局部超温带来的安全性等问题。以某330 MW CFB锅炉的深度调峰技术应用为例,介绍了输煤筛分破碎系统、风帽节流圈、下二次风管等机组部件的改造,并配合烟气再循环等技术应用,成功实现了18%的超低负荷深度调峰运行,同时也很好地控制了NOx的排放。最后总结了CFB机组超低负荷深度调峰技术的关键点和难点,对深度调峰运行带来的潜在问题进行了分析,并提出了相应的解决措施。研究结果具有重要的工程借鉴作用。

超临界循环流化床锅炉水冷壁吸热偏差计算及深度调峰水动力特性

超临界循环流化床锅炉在深度调峰过程中受热负荷及质量流速变化的影响容易出现管壁拉裂、超温爆管等安全问题,故有必要对锅炉深度调峰负荷时热偏差系数、水动力特性进行计算研究。该文根据超临界循环流化床锅炉水冷壁及水冷屏结构,建立水动力计算数学模型并运用实炉测量数据计算实炉热偏差系数,对310及110MW负荷实炉热偏差系数进行计算,并采用110MW负荷实炉热偏差系数对120及70MW(深度调峰负荷)的水动力进行计算,将120MW负荷时的出口汽温计算结果与实炉测量数据进行对比验证,对70MW深度调峰负荷水动力计算结果进行分析。结果表明:循环流化床锅炉高低负荷时热偏差系数分布规律不同,在相近负荷时炉膛热偏差系数呈现出一致性,并且锅炉在70MW深度调峰负荷时,锅炉能安全稳定运行。深度调峰负荷时循环流化床锅炉吸热偏差系数及水动力特性的计算研究,为现有火电机组进行灵活性深度调峰优化改造提供一定的理论基础。

超临界660 MW循环流化床锅炉NO_(x)排放控制困难分析及处理

为解决某电厂超临界660 MW循环流化床(circulating fluidized bed,CFB)锅炉满负荷运行NO_(x)排放较难控制、瞬时值易超过超低排放限值且选择性非催化还原(selective non-catalytic reduction,SNCR)脱硝系统氨耗量较大氨逃逸严重的问题,现场进行了NO_(x)原始排放、SNCR脱硝效率、CO质量浓度及底渣可燃物的试验,并进行了二次风量布置优化试验。研究发现:锅炉原始NO_(x)排放较低,满负荷运行时不超过120 mg/m^(3)(标准状态,下同);中低负荷时NO_(x)质量浓度低于50 mg/m^(3),但炉膛前后NO_(x)质量浓度偏差较大,烟气中的NO_(x)主要在炉膛前部产生。NO_(x)排放较难控制的原因是SNCR脱硝效率较低和炉膛给煤不均。6台分离器入口的SNCR脱硝效率均低于50.0%,其中B、C、E、F 4台分离器脱硝效率低于40.0%。此外,从原始NO_(x)生成来看,根据炉膛深度方向上床温分布、底渣可燃物质量分数和CO质量浓度变化可以确定,炉膛给煤不均也对满负荷NO_(x)排放控制影响显著。当前,电厂若不进行给煤系统改造暂无法实现给煤均匀,但可以通过调整炉膛深度方向二次风量配比降低原始NO_(x)生成,降幅可达9.77%。

不带外置床的700 MW超超临界循环流化床锅炉失电后水冷壁安全计算分析

通过对某660 MW电厂失电事故过程中烟气温度、蒸汽温度及工质流量的变化规律进行分析,得到了炉膛密相区、过渡区及稀相区热负荷随时间的变化规律。在此基础上,以某700MW超超临界循环流化床(circulating fluidized bed,CFB)锅炉为对象,建立了失电事故发生后水冷壁内的流动传热计算模型,开发了以Fortran语言为基础的水冷壁内瞬态特性计算程序。分别对密相区、过渡区及稀相区进行分析,通过计算得到了失电后的水冷壁壁温及出口工质温度等热力参数的变化规律。计算结果表明:失电后水冷壁密相区出口的最高壁温为558.6℃,稀相区出口的最高壁温为579.6℃,不需要配备紧急补水泵来保证失电后水冷壁的安全。研究结果可为电厂处理超超临界CFB锅炉失电事故提供指导。