Designing a Dual-Feed Circular Polarization Antenna

This paper describes a novel dual-feed circularly polarized antenna,and the dual feeding mode is realized by grooving on the antenna radiator.The antenna utilizes air dielectric material to meet the requirements of low weight and cost.Test results demonstrate that the antenna exhibits capacitive loading between the metal antenna patch and the ground floor,allowing for adjustment of the working frequency of the dual-feed circularly polarized microstrip antenna.Specifically,the original center frequency of 2.264 GHz was reduced to 1.582 GHz,facilitating antenna miniaturization and broad bandwidth.With a return loss(S11)below-10 dB,a bandwidth of 72 MHz(1.552-1.624 GHz)was obtained.Additionally,the dual-feed microstrip antenna incorporates a 90°bridge,resulting in circular polarization gains of 2.26 dBi at 1.561 GHz and 2.45 dBi at 1.575 GHz.Overall,the antenna design offers a large working bandwidth and excellent circular polarization characteristics,making it suitable for a wide range of applications in satellite navigation and positioning terminals.

Dynamic phase assembled terahertz metalens for reversible conversion between linear polarization and arbitrary circular polarization

If a metalens integrates the circular polarization(CP)conversion function,the focusing lens together with circular-polariz-ing lens(CPL)in traditional cameras may be replaced by a metalens.However,in terahertz(THz)band,the reported metalenses still do not obtain the perfect and strict single-handed CP,because they were constructed via Pancharatnam-Berry phase so that CP conversion contained both left-handed CP(LCP)and right-handed CP(RCP)components.In this paper,a silicon based THz metalens is constructed using dynamic phase to obtain single-handed CP conversion.Also,we can rotate the whole metalens at a certain angle to control the conversion of multi-polarization states,which can simply manipulate the focusing for incident linear polarization(LP)THz wave in three polarization conversion states,in-cluding LP without conversion,LCP and RCP.Moreover,the polarization conversion behavior is reversible,that is,the THz metalens can convert not only the LP into arbitrary single-handed CP,but also the LCP and RCP into two perpen-dicular LP,respectively.The metalens is expected to be used in advanced THz camera,as a great candidate for tradi-tional CPL and focusing lens group,and also shows potential application in polarization imaging with discriminating LCP and RCP.

Wide-band circular polarization-keeping reflection mediated by metasurface

In this paper, we show that circular polarization-keeping reflection can be achieved using reflective metasurfaces. The underlying physical mechanism of the polarization-keeping reflection is analyzed using a reflection matrix. A wideband circular polarization-keeping reflector is demonstrated using N-shaped resonators. Both the simulation and experiment results show that the polarization-keeping reflection can be achieved with a high efficiency larger than 98% over the frequency range from 9.2 GHz to 17.7 GHz for both incident left- and right-handed circularly polarized waves. Under oblique incidence, the bandwidth increases as the incident angle varies from 0°to 80°. Moreover, the co-polarization reflection is independent of the incident azimuth angles.

Circular Polarization Hologram Realized by Pancharatnam-Berry Phase in Microwave Frequency

Metasurfaces have shown great potential in controlling the propagation of electromagnetic waves, making them suitable for holographic beam-shaping elements. Using the principle of array synthesis, holograms have been realized in microwave frequency to manipulate electromagnetic waves to generate specific field patterns. However, current research is almost based on linear polarization and has little analysis on the circular polarization microwave hologram. Herein, we propose a circular polarization hologram realized by sub-wavelength units with self-adaptively phase profiles of electromagnetic waves. The full, continuous control of the phase is achieved by using a single structure unit based on the Pancharatnam-Berry phase. The inhomogeneity of wave-front is considered through amplitude and phase compensation which are essential to improve the quality of microwave hologram. The model achieves circular polarization hologram in microwave frequency and the clear field pattern is generated. The circular polarization hologram enriched the research field of microwave imaging, thus providing more inspirations for the development of various related techniques.

Imprints of molecular orbitals using photoelectron angular distribution by strong laser pulses of circular polarization

We theoretically investigate the strong-field ionization of H＋2 molecules in four different electronic states by calculating photoelectron angular distributions in circularly polarized fields. We find that the structure of photoelectron angular distribution depends on the molecular orbital as well as the energy of the photoelectron. The location of main lobes changes with the symmetric property of the molecular orbital. Generally, for molecules with bonding electronic states, the photoelectron’s angular distribution shows a rotation of π/2 with respect to the molecular axis, while for molecules with antibonding electronic states, no rotation occurs. We use an interference scenario to interpret these phenomena. We also find that, due to the interference effect, a new pair of jets appears in the waist of the main lobes, and the main lobes or jets of the photoelectron’s angular distribution are split into two parts if the photoelectron energy is sufficiently high.

Asymmetric Patch Element Reflectarray with Dual Linear and Dual Circular Polarization

A reflectarray antenna consisting of asymmetrical patch elements is proposed,which is capable of producing dual linear and dual circular polarized operation at 26GHz frequency.The main purpose of this design is to support four different polarizations using the same patch element.The proposed reflectarray has a single layer configuration with a linearly polarized feed and circular ring slots in the ground plane.Asymmetric patch element is designed from a square patch element by tilting its one vertical side to some optimized inclination.A wide reflection phase range of 600°is obtained with the asymmetric patch element during unit cell measurements.A 332 element circular aperture reflectarray is designed with the proposed configuration and experimentally validated with a linearly polarized prime feed configuration.Two different orientations of mirror and non-mirror asymmetric patch elements on the surface of reflectarray are analyzed.Dual linear polarization is obtained with the mirror orientation of the asymmetric patch elements on the surface of reflectarray.Alternatively,asymmetric patch elements without mirror orientation are demonstrated to produce dual circular polarization with the same linearly polarized feed.A maximum measured gain of 24.4 dB and 26.1 dB is achieved for dual linear and dual circular polarization,respectively.Their respective measured efficiencies are 28%and 41.3%,which are supported by amaximum−3 dB gain bandwidth of 13.8%and 11.5%.The circular polarization operation of the reflectarray is also supported by a 6 dB axial ratio bandwidth of 9.2%.The proposed asymmetric patch reflectarray antenna with polarization diversity,wide bandwidth and high gain is suitable to be used in many high frequency applications of 5G communication.

Ultra-wideband linear-to-circular polarization conversion metasurface

An ultra-wideband and high-efficiency reflective linear-to-circular polarization conversion metasurface is proposed. The proposed metasurface is composed of a square array of a corner-truncated square patch printed on grounded dielectric substrate and covered with a dielectric layer, which is an orthotropic anisotropic structure with a pair of mutually perpendicular symmetric axes u and v along the directions with the tilt angles of ±45° with respect to the vertical y axis. When the u- and v-polarized waves are incident on the proposed metasurface, the phase difference between the two reflection coefficients is close to –90° in an ultra-wide frequency band, so it can realize high-efficiency and ultra-wideband LTC polarization conversion under both x- and y-polarized incidences in this band. The proposed polarization conversion metasurface is simulated and measured. Both the simulated and measured results show that the axial ratio (AR) of the reflected wave is kept below 3 dB in the ultra-wide frequency band of 5.87 GHz–21.13 GHz, which is corresponding to a relative bandwidth of 113%;moreover, the polarization conversion rate (PCR) can be kept larger than 99% in a frequency range of 8.08 GHz–20.92 GHz.

Wideband linear-to-circular polarization conversion realized by a transmissive anisotropic metasurface

We propose a metasurface which consists of three conductive layers separated by two dielectric layers. Each conductive layer consists of a square array of square loop apertures, however, a pair of corners of each square metal patch surrounded by the square loop apertures have been truncated, so it becomes an orthotropic structure with a pair of mutually perpendicular symmetric axes u and v. The simulated results show that the metasurface can be used as a wideband transmission-type polarization converter to realize linear-to-circular polarization conversion in the frequency range from12.21 GHz to 18.39 GHz, which is corresponding to a 40.4% fractional bandwidth. Moreover, its transmission coefficients at x-and y-polarized incidences are completely equal. We have analyzed the cause of the polarization conversion, and derived several formulas which can be used to calculate the magnitudes of cross-and co-polarization transmission coefficients at y-polarized incidence, together with the phase difference between them, based on the two independent transmission coefficients at u-and v-polarized incidences. Finally, one experiment was carried out, and the experiment and simulated results are in good agreement with each other.

Testing Bell’s Theorem with Circular Polarization

Bell tests with entangled light have been performed many times in many ways using linear polarizers, but the same tests have never been done with a circular polarizer. Until recently there has never been a true circular polarization beamsplitter—an optical component that separates light directly into left and right handed polarizations. Using a true circular polarization beamsplitter based on birefringent gratings, entangled light has been analyzed with unexpected results.

Hot-exciton effects on exciton diffusion and circular polarization dynamics in a single PbI_(2)nanoflake

As one of the emerging two-dimensional lead halide materials,lead iodide(PbI_(2))nanosheets have proven to possess strong application potential in the fields of high-energy radiation detection and highly efficient perovskite solar cells.However,the underlying photophysical properties such as hot-exciton-related carrier dynamics remain unclear for PbI_(2)nanosheets.Here,we report the exciton dynamics of a single PbI_(2)nanoflake prepared by an aqueous solution method.Through a three-dimensional(3D)diffusion model,we obtain the exciton annihilation radius and diffusion coefficient of a single PbI_(2)nanoflake under nonresonant and resonant excitation conditions of band-edge exciton state.As initial exciton densities increase,we find the carrier recombination mechanism for a single PbI_(2)nanoflake gradually changes from exciton-exciton annihilation to free-carrier recombination.Finally,we reveal the room-temperature circular polarization of a single PbI_(2)nanoflake is due to free-carrier recombination with a band-edge exciton dissociation time of~120 fs under the resonant excitation condition.

Ultra-thin single-layer transparent geometrical phase gradient metasurface and its application to high-gain circularly-polarized lens antenna

A new method to design an ultra-thin high-gain circularly-polarized antenna system with high efficiency is proposed based on the geometrical phase gradient metasurface（GPGM）.With an accuracy control of the transmission phase and also the high transmission amplitude,the GPGM is capable of manipulating an electromagnetic wave arbitrarily.A focusing transmission lens working at Ku band is well optimized with the F /D of 0.32.A good focusing effect is demonstrated clearly by theoretical calculation and electromagnetic simulation.For further application,an ultra-thin single-layer transmissive lens antenna based on the proposed focusing metasurface operating at 13 GHz is implemented and launched by an original patch antenna from the perspective of high integration,simple structure,and low cost.Numerical and experimental results coincide well,indicating the advantages of the antenna system,such as a high gain of 17.6 d B,the axis ratio better than 2 d B,a high aperture efficiency of 41%,and also a simple fabrication process based on the convenient print circuit board technology.The good performance of the proposed antenna indicates promising applications in portable communication systems.

A novel x-ray circularly polarized ranging method

Range measurement has found multiple applications in deep space missions. With more and further deep space ex- ploration activities happening now and in the future, the requirement for range measurement has risen. In view of the future ranging requirement, a novel x-ray polarized ranging method based on the circular polarization modulation is proposed, termed as x-ray circularly polarized ranging （XCPolR）. XCPolR utilizes the circular polarization modulation to process x-ray signals and the ranging information is conveyed by the circular polarization states. As the circular polarization states present good stability in space propagation and x-ray detectors have light weight and low power consumption, XCPolR shows great potential in the long-distance range measurement and provides an option for future deep space ranging. In this paper, we present a detailed illustration of XCPolR. Firstly, the structure of the polarized ranging system is described and the signal models in the ranging process are established mathematically. Then, the main factors that affect the ranging accuracy, including the Doppler effect, the differential demodulation, and the correlation error, are analyzed theoretically. Finally, numerical simulation is carded out to evaluate the performance of XCPolR.

Single-Layer Wideband Circularly Polarized Antenna Using Non-Uniform Metasurface for C-band Applications

A single-layer design of non-uniform metasurface(MS)based circularly polarized(CP)antenna with wideband operation characteristic is proposed and investigated in this paper.The antenna is excited by a truncated corner squared patch as a primary radiating CP source.Then,a non-uniform MS is placed in the same layer with the driven patch.Besides increasing the impedance bandwidth,the non-uniform MS also generates two additional CP bands in the high frequency band,leading to significantly increase the antenna’s overall performances.The use of non-uniform MS distinguishes our design from the other CP MS based antennas in literature,in which the MS is formed by multiple uniform unit cells and placed in different layer with the radiating element.For validation,an antenna prototype,whose overall dimensions of 0.94λ_(o)×0.94λ_(o)×0.06λ_(o) at the center operating frequency,is fabricated and experimentally tested.The measured operating bandwidth with|S11|≤−10 dB and AR≤3 dB is 27.1%(5.1–6.7 GHz)and the broadside gain within this band is from 5.7 to 7.2 dBic.Compared to the other related works,the proposed antenna has advantage of very wideband operation with single-layer design.

Compact and broadband circularly polarized ring antenna with wide beam-width for multiple global navigation satellite systems

A compact and broadband circularly polarized （CP） annular ring antenna with wide beam-width is proposed for multiple global navigation satellite systems （GNSS） in the L1 band. The annular ring is excited by two modified L-probes with quadrature phase difference. It has a 36.3% 10-dB return loss bandwidth and a 13% 3-dB axial ratio bandwidth, because of the orthogonal L-probes with 90° phase difference. The measured peak gain of the antenna is 3.9 dBic. It can detect the satellites at lower elevation as its half power beam-width （HPBW） is 113° in both the x-z and y-z planes, achieving a cross-polarization level of larger than 25 dB. Noticeably, the antenna achieves 89% size reduction compared with the conventional half wavelength patch antennas. It can be used in hand-held navigation devices of multiple GNSS such as COMPASS, Galileo, GPS and GLONASS.

An AMC-Based Circularly Polarized Antenna for 5G sub-6 GHz Communications

This paper presents an AMC(artificial magnetic conductor)-based wideband circularly polarized printed monopole antenna for unidirectional radiation.The antenna includes an AMC reflector,a coplanar waveguide(CPW)feed structure to excite the antenna,a ground plane with a rectangular slot on the left side of feedline,and an asymmetrical ground plane on its right side.The induced surface currents on CWP feedline,rectangularly slotted,and asymmetrical ground planes cause circularly polarized radiations.The AMC reflector consisting periodic metallic square patches is used instead of the conventional PEC(perfect electric conductor)reflector,the distance between the antenna and reflector is reduced from 0.25λ0 to 0.18λ0 with performance improvement.By incorporating AMC layer with the monopole antenna,the gain of antenna is increased from 3.3 dBic to 8.7 dBic while the axial ratio bandwidth(ARBW)of antenna is increased from 27.27%to 51.67%.The simulated and measured results show that the proposed antenna has an overlapping 10-dB|S_(11)|and 3-dB ARBW of 51.67%(3.0–5.09 GHz).The overall dimensions of monopole antenna backed by AMC reflector is 1.20_(λ0)×1.20_(λ0)×0.21_(λ0) and covers 5G sub-6 GHz new radio bands(n77/n78/n79)for wireless communication systems.

Novel circularly-polarized ceramic dielectric resonator antenna excited by a corner-cut square patch

A ceramic dielectric resonator antenna excited by a corner-cut square patch for the circularly-polarized operation is introduced. The effect of patch size and cut size is investigated, showing that the resonant frequency of the antenna can be changed by simply changing the patch size. The reflection, axial ratio, and radiation characteristics of the antenna are found. Measurements were carried out to verify the design. The antenna is compact in structure, which is attractive in the application as the satellite communication terminals.

A Wideband Circularly Polarized Jeans-Based Antenna at 2.45 GHz

Development of textile antennas is an important segment towards the goal of creating smart clothing. In this paper, we report on a jeans-based circularly polarized textile antenna designed for the E-band (around 2.45 GHz). We present three variations of the design and the respective results. The antenna comprises a multi-layer jeans-fabric as the substrate, a conductive fabric as the patch, which is concealed with another layer of jeans, and the ground plane is formed by either a cooper foil or another conductive fabric. A multi-layer structure was chosen to provide a wider bandwidth and better efficiency, whereas the upper surface of the antenna was covered by one more layer of jeans to both make the antenna less conspicuous, when worn on the arm, and protect the patch and substrate from mechanical damages and moisture. All three variants are characterized by a good realized gain of about 3 dB, a wide beam width and a wide bandwidth of 21% or better, around 2.45 GHz, having the radiation efficiency around 36%, and front-to-back ratio of 5 dB or better, with the ground plane being just slightly larger than the patch.

On the Design of Slot Cut Circularly Polarized Circular Microstrip Antennas

Circularly polarized microstrip antenna is frequently realized by cutting the slot inside the patch and feeding it along the diagonal axis. In the reported literature, procedure to design them at any given frequency is not available. In proposed work, circularly polarized slot cut circular microstrip antenna at 900 MHz is discussed. By studying the surface current distributions at two orthogonal modes, formulations in their resonant length are proposed. The frequencies calculated using them closely agree with simulated results. Using proposed formulation, procedure to design circular polarized antennas at different frequencies is presented that gives circular polarized response. Thus, proposed work will be helpful to design similar circular polarized circular microstrip antenna at any desired frequency.

Multi-band circular polarizer based on a twisted triple split-ring resonator

A multi-band circular polarizer using a twisted triple split-ring resonator（TSRR） is presented and studied numerically and experimentally. At four distinct resonant frequencies, the incident linearly polarized wave can be transformed into left/right-handed circularly polarized waves. Numerical simulation results show that a y-polarized wave can be converted into a right-handed circularly polarized wave at 5.738 GHz and 9.218 GHz, while a left-handed circularly polarized wave is produced at 7.292 GHz and 10.118 GHz. The experimental results are in agreement with the numerical results. The surface current distributions are investigated to illustrate the polarization transformation mechanism. Furthermore, the influences of the structure parameters of the circular polarizer on transmission spectra are discussed as well.

Polarization switching characteristics in a 1550nm VCSEL subject to circularly polarized optical injection

Polarization switching （PS） characteristics in a 1550 nm vertical-cavity surface-emitting laser （VCSEL） subject to circularly polarized optical injection （CPOI） are experimentally investigated. The results show that, under different biased current, a solitary 1550 nm VCSEL can oscillate at y polarization mode （y mode）, two polari- zation components （PCs） coexistence or x polarization mode （x mode）. The PS characteristics induced by CPOI for the VCSEL operating at y mode and x mode are analyzed and the evolutions of dynamical states with the injected power are discussed. Additionally, the mappings of nonlinear dynamical states are given in the parameters space of the injected power and frequency detuning.