Semi-analytical solution for drained expansion analysis of a hollow cylinder of critical state soils

The expansion of a thick-walled hollow cylinder in soil is of non-self-similar nature that the stress/deformation paths are not the same for different soil material points.As a result,this problem cannot be solved by the common self-similar-based similarity techniques.This paper proposes a novel,exact solution for rigorous drained expansion analysis of a hollow cylinder of critical state soils.Considering stress-dependent elastic moduli of soils,new analytical stress and displacement solutions for the nonself-similar problem are developed taking the small strain assumption in the elastic zone.In the plastic zone,the cavity expansion response is formulated into a set of first-order partial differential equations(PDEs)with the combination use of Eulerian and Lagrangian descriptions,and a novel solution algorithm is developed to efficiently solve this complex boundary value problem.The solution is presented in a general form and thus can be useful for a wide range of soils.With the new solution,the non-self-similar nature induced by the finite outer boundary is clearly demonstrated and highlighted,which is found to be greatly different to the behaviour of cavity expansion in infinite soil mass.The present solution may serve as a benchmark for verifying the performance of advanced numerical techniques with critical state soil models and be used to capture the finite boundary effect for pressuremeter tests in small-sized calibration chambers.

Physical and mechanical properties and microstructures of submarine soils in the Yellow Sea

In recent years,the exploration of seabed has been intensified,but the submarine soils of silt and sand in the Yellow Sea area have not been well investigated so far.In this study,the physical and mechanical properties of silt and sand from the Yellow Sea were measured using a direct shear apparatus and their microstructures were observed using a scanning electron microscope.The test results suggest that the shear strength of silt and sand increases linearly with the increase of normal stress.Based on the direct shear test,the scanning electron microscope was used to observe the section surface of sand.It is observed that the section surface becomes rough,with many“V”‐shaped cracks.Many particles appear on the surface of the silt structure and tend to be disintegrated.The X‐ray diffraction experiment reveals that the sand and silt have different compositions.The shear strength of sand is slightly greater than that of silt under high stress,which is related to the shape of soil particles and the mineral composition.These results can be a reference for further study of other soils in the Yellow Sea;meanwhile,they can serve as soil parameters for the stability and durability analyses of offshore infrastructure construction.

Liquefaction susceptibility and deformation characteristics of saturated coral sandy soils subjected to cyclic loadings-a critical review

Coral sandy soils widely exist in coral island reefs and seashores in tropical and subtropical regions.Due to the unique marine depositional environment of coral sandy soils,the engineering characteristics and responses of these soils subjected to monotonic and cyclic loadings have been a subject of intense interest among the geotechnical and earthquake engineering communities.This paper critically reviews the progress of experimental investigations on the undrained behavior of coral sandy soils under monotonic and cyclic loadings over the last three decades.The focus of coverage includes the contractive-dilative behavior,the pattern of excess pore-water pressure(EPWP)generation and the liquefaction mechanism and liquefaction resistance,the small-strain shear modulus and strain-dependent shear modulus and damping,the cyclic softening feature,and the anisotropic characteristics of undrained responses of saturated coral sandy soils.In particular,the advances made in the past decades are reviewed from the following aspects:(1)the characterization of factors that impact the mechanism and patterns of EPWP build-up;(2)the identification of liquefaction triggering in terms of the apparent viscosity and the average flow coefficient;(3)the establishment of the invariable form of strain-based,stress-based,or energy-based EPWP ratio formulas and the unique relationship between the new proxy of liquefaction resistance and the number of cycles required to reach liquefaction;(4)the establishment of the invariable form of the predictive formulas of small strain modulus and strain-dependent shear modulus;and(5)the investigation on the effects of stress-induced anisotropy on liquefaction susceptibility and dynamic deformation characteristics.Insights gained through the critical review of these advances in the past decades offer a perspective for future research to further resolve the fundamental issues concerning the liquefaction mechanism and responses of coral sandy sites subjected to cyclic loadings associated with seismic events in marine environments.

Extended wet sieving method for determination of complete particle size distribution of general soils

The traditional standard wet sieving method uses steel sieves with aperture?0.063 mm and can only determine the particle size distribution(PSD)of gravel and sand in general soil.This paper extends the traditional method and presents an extended wet sieving method.The extended method uses both the steel sieves and the nylon filter cloth sieves.The apertures of the cloth sieves are smaller than 0.063 mm and equal 0.048 mm,0.038 mm,0.014 mm,0.012 mm,0.0063 mm,0.004 mm,0.003 mm,0.002 mm,and 0.001 mm,respectively.The extended method uses five steps to separate the general soil into many material sub-groups of gravel,sand,silt and clay with known particle size ranges.The complete PSD of the general soil is then calculated from the dry masses of the individual material sub-groups.The extended method is demonstrated with a general soil of completely decomposed granite(CDG)in Hong Kong,China.The silt and clay materials with different particle size ranges are further examined,checked and verified using stereomicroscopic observation,physical and chemical property tests.The results further confirm the correctness of the extended wet sieving method.

Temporal and environmental factors drive community structure and function of methanotrophs in volcanic forest soils

Methanotrophs,organisms that obtain oxygen by oxidizing methane,are recognized as the only known biological sink for atmospheric CH_4,and forest soil methanotrophs play crucial roles in mitigating global warming.The succession patterns of methanotrophic communities and functions in Wudalianchi volcano forest soils could provide a basis for the study of evolutionary mechanisms between soil microorganisms,the environment,and carbon cycling of temperate forest ecosystems under climate change.In this study,the characteristics and drivers of methanotrophic community structure and function of two volcanic soils at different stages of development are analyzed,including an old volcano and a new volcano,which most recently erupted 300 years and 17-19×10^(5)years ago,respectively,and a non-volcano hills as control,based on space for time substitution and Miseq sequencing and bioinformation technology.The results showed that CH_(4) fluxes were significantly higher in old-stage volcano forest soils than new-stage forest soils and non-volcano forest soils.There were significant differences in the community composition and diversity of soil methanotrophs from different volcano forest soils.Methylococcus was the dominant genus in all soil samples.Additionally,the relative abundance of Methylococcus,along with Clonothrix,Methyloglobulus,Methylomagum,Methylomonas and Methylosarcina,were the important genera responsible for the differences in methanotrophic community structure in different volcano forest soils.The relative abundance of methanotroph belonging toγ-proteobacteria was significantly higher than that belonging toα-proteobacteria(P<0.05).Chao1,Shannon and Simpson indices of soil methanotrophic community were significantly lower in new-stage volcanos and were significantly affected by bulk density,total porosity,p H,nitrate,dissolved organic carbon and dissolved organic nitrogen.There were significant differences in community structure between new-stage and old-stage volcanoes.Bulk density and p H are important soil properties contributing to the divergence of methanotrophs community structure,and changes in soil properties due to soil development time are important factors driving differences in methanotrophs communities in Wudalianchi volcanic soils.

Discussion of“Site observations of weathered granitic soils subjected to cementation and partial drainage using SCPTU”[J Rock Mech Geotech Eng 15(2023)984e996]

Comprehensive data from in situ and laboratory tests in residual soil have been presented by Zhang et al.(2023).A number of issues addressed in the paper have been the interest of the discussers,namely the characterisation and behaviour of residual soils,limitation of piezocone testing due to the capacity of the entire system,measurement of shear wave velocity,rate effect of piezocone(CPTU)testing and piezocone testing with dual pore pressure penetrometers.Clarification and complementation of these issues are required with regard to both the execution and interpretation of the tests.

Geochemical Characterization of Soils in the Playa Lake Environment of Laguna de Encinillas, Chihuahua, Mexico

Laguna de Encinillas, located in Chihuahua, Mexico, is an ephemeral lake situated within a playa lake sedimentary depositional environment. This region plays a significant role in the aquifer supplying water to Chihuahua City. A surficial soil sampling campaign was conducted in 2017, 2018, and 2021 to assess the potential impact of surface soil composition on groundwater quality. The collected soil samples were analyzed using inductively coupled plasma mass spectrometry (ICP-MS) following microwave-assisted digestion. The analytical results were employed to generate spatial distribution maps of elemental concentrations using QGIS, applying interpolation methods such as inverse distance weighting (IDW) and Kriging. The analysis revealed elevated concentrations of beryllium (Be), calcium (Ca), cadmium (Cd), chromium (Cr), magnesium (Mg), and strontium (Sr) in the eastern part of the study area. In contrast, arsenic (As) and iron (Fe) were more prevalent in the western sector. Notably, high levels of barium (Ba), silver (Ag), cobalt (Co), potassium (K), and scandium (Sc) were identified in the northeastern region. At the same time, nickel (Ni), titanium (Ti), and vanadium (V) were concentrated in the northern portion. Manganese (Mn) was particularly prominent in the southern area. The geogenic source of these elements is likely linked to the volcanic rocks from the surrounding mountain ranges.

Effect of Some Physical Factors on Interrill Erosion of Soils in Gidan-Kwanu Area, Nigeria

Savanna regions in Nigeria face environmental degradation and barren land, negatively impacting food and agricultural productivity. Inter-rill erosion occurs due to raindrop impact and transport, particularly on hill slopes. A study was conducted using a sprinkler rainfall simulator and plot experiment to study soil erosion processes. Soil samples were collected from four farms in Gidan Kwanu, with varying moisture content. Sand content ranged from 46.0% to 76.20%, silt from 11.30% to 23.50%, and clay from 11.0% to 30.0%. Uncultivated and bare land had a higher average porosity (15.47% and 14.99%), while cultivated land had lower porosity (14.4%). The study found that most people in Gidan-Kwanu primarily practice farming, which is season-dependent and rain-fed. Soil type and texture significantly contribute to inter-rill erosion, with cultivated and uncultivated soil being more resistant to erosion than bare land soil. The study concluded that farming practices in Gidan-Kwanu are primarily season-dependent and rain-fed. Soil type and texture significantly contribute to inter-rill erosion, with cultivated and uncultivated soil being more resistant to erosion than bare land soil.

Afforestation increases microbial diversity in low-carbon soils

Afforestation has an important role in biodiversity conservation and ecosystem function improvement.A meta-analysis was carried out in China,which has the largest plantation area globally,to quantify the effects of plantings on soil microbial diversity.The results showed that the overall effect of afforestation on soil microbial diversity was positive across the country.Random forest algorithm suggested that soil carbon was the most important factor regulating microbial diversity and the positive response was only found with new plantings on low-carbon bare lands but not on high-carbon farmlands and grasslands.In addition,afforestation with broadleaved species increased microbial diversity,whereas planting with conifers had no effect on microbial diversity.This study clarified the effects of plantings on soil microbial diversity,which has an important implication for establishing appropriate policies and practices to improve the multiple functionalities(e.g.,biodiversity conservation and climate change mitigation)during plantation establishment.

A bounding surface visco-plasticity model considering generalized spacing ratio of soils

The non-unique critical state of soils with time-dependent behaviors is a significant issue in geotechnical engineering problems.However,previous bounding surface plasticity models cannot predict accurately the non-unique critical state of soils,because the distance between the compression line and critical state line charged by strain-rate effect is basically neglected.To fill this gap,a generalized spacing ratio of soils is defined in the elasto-viscoplastic framework,and a bounding surface visco-plasticity model is formulated and verified,which can consider the generalized spacing ratio.Specifically,the generalized spacing ratio of soils reflects the distance between the compression line and the critical state line of soils with time-dependent behaviors.Then,the generalized spacing ratio is introduced into an improved anisotropic bounding surface.A new expression of the visco-plastic multiplier is derived by solving the consistency equation of an anisotropic bounding surface.In the expression,a strain rate index is proposed to account for the strain-rate effect on visco-plastic strain increment,and a visco-plastic hardening modulus is derived to predict the visco-plastic response of soils in overconsolidation conditions.The model is then verified through constant strain rate tests and creep tests.Notably,it can capture the non-unique critical states of soils with time-dependent behaviors due to the generalized spacing ratio and the creep rupture of soils due to the visco-plastic multiplier that considers the stress ratio and visco-plastic strain rate.

Accurate method based on data filtering for quantitative multi-element analysis of soils using CF-LIBS

To obtain more stable spectral data for accurate quantitative analysis of multi-element,especially for the large-area in-situ elements detection of soils, we propose a method for a multielement quantitative analysis of soils using calibration-free laser-induced breakdown spectroscopy(CF-LIBS) based on data filtering. In this study, we analyze a standard soil sample doped with two heavy metal elements, Cu and Cd, with a specific focus on the line of Cu I324.75 nm for filtering the experimental data of multiple sample sets. Pre-and post-data filtering,the relative standard deviation for Cu decreased from 30% to 10%, The limits of detection(LOD)values for Cu and Cd decreased by 5% and 4%, respectively. Through CF-LIBS, a quantitative analysis was conducted to determine the relative content of elements in soils. Using Cu as a reference, the concentration of Cd was accurately calculated. The results show that post-data filtering, the average relative error of the Cd decreases from 11% to 5%, indicating the effectiveness of data filtering in improving the accuracy of quantitative analysis. Moreover, the content of Si, Fe and other elements can be accurately calculated using this method. To further correct the calculation, the results for Cd was used to provide a more precise calculation. This approach is of great importance for the large-area in-situ heavy metals and trace elements detection in soil, as well as for rapid and accurate quantitative analysis.

Analysis of the Fertilizing and Bioremediation Potential of Leaf Litter Compost Amendment in Different Soils through Indexing Method

This research study explored the efficacy of leaf litter compost as a sustainable soil amendment with the objective of promoting soil health and mitigating the accumulation of potentially toxic elements. The investigation encompassed the impact of various organic compost amendments, including leaf compost, cow dung manure, kitchen waste compost, municipal organic waste compost, and vermicompost. The study employed Inductively Coupled Plasma Mass Spectrometry (ICP-MS) to evaluate soil nutrient levels and concentrations of Potentially Toxic Elements (PTEs) such as arsenic, chromium, cadmium, mercury, lead, nickel, and lithium. The fertilization and bioremediation potential of these compost amendments are quantified using an indexing method. Results indicated a substantial increase in overall nutrient levels (carbon, nitrogen, phosphorus, potassium, and sulfur) in soils treated with leaf compost and other organic composts. Fertility indices (FI) are notably higher in compost-amended soils (ranging from 2.667 to 3.938) compared to those amended with chemical fertilizers (ranging from 2.250 to 2.813) across all soil samples. Furthermore, the mean concentrations of PTEs were significantly lower in soils treated with leaf compost and other organic compost amendments compared to those treated with chemical fertilizers amendments. The assessment through the indexing method revealed a high clean index (CI) for leaf compost amendment (ranging from 3.407 to 3.58), whereas the chemical fertilizer amendment exhibits a relatively lower CI (ranging from 2.78 to 3.20). Consequently, leaf compost and other organic composts exhibit the potential to enhance sustainable productivity, promoting soil health and environmental safety by improving nutrient levels and remediating potentially toxic elements in the soil.

Physicochemical and Bacteriological Profile of Bilanko and Ngamakala Peat Bog Soils (Republic of Congo)

Peatlands are unique and complex natural ecosystems that are part of the most important carbon reservoirs on our planet, home to a diversity of microorganisms responsible for fermentation, humification or peat. The aim is to understand chemical and biological indicators of peatland soils. This work aims to determine the physicochemical and bacteriological profile and lipolytic activity of soil bacteria in Bilanko peatlands. The bacterial profile with the production of lipases is carried out by classical microbiology techniques. The results show that the soils are moderately acidic with temperatures of 27.8˚C ± 0.01˚C for Bilanko and 27.1˚C ± 0.57˚C for Ngamakala. The electroconductivity (EC) varies from (9.52 ± 0.002) μS/cm to (39.01 ± 1.4) μS/cm with low turbidity of (2.04 ± 0.66) mg/L to (31.02 ± 0.84) mg/L and low ion concentrations with, however, a richness in phenolic compounds for Bilanko compared to Ngamakala. FMAT diversity ranged from (1.71 ± 0.88)∙104 UFC/g to (2.92 ± 0.07)∙105 UFC/g for Bilanko and (1.30 ± 0.73)∙104 UFC/g to (2.89 ± 0.06)∙104 UFC/g for Ngamakala. Bacillus loads ranged from (5.20 ± 1.40)∙103 CFU/g to (1.22 ± 0.13)∙104 CFU/g and from (1.11 ± 0.13)∙104 CFU/g to (9.20 ± 2.05)∙103 CFU/g;enterobacteria loads from (1.40 ± 0.76)∙103 CFU/g to (8.80 ± 1.73)∙103 CFU/g and from (1.01 ± 0.02)∙103 CFU/g to (9.20 ± 2.05)∙103 CFU/g;in Pseudomonas from 0 to (2.30 ± 0.53)∙102 CFU/g and from 0 to (8.90 ± 2.35)∙102 CFU/g for Bilanko and Ngamakala respectively. These results reveal a variation in bacterial similarity and distribution in the Bilanko and Ngamakala peat bogs.

Different Approaches to Reduce Salinity in Salt-Affected Soils and Enhancing Salt Stress Tolerance in Plants

Salt stress is one of the most harmful environmental stresses in recent times and represents a significant threat to food security. Soil salinization is caused by spontaneous natural processes of mineral dissolution and human activities such as inappropriate irrigation practices. Natural geological progressions like weathering of rocks, arid climate, and higher evaporation, as well as anthropogenic activities, including the use of brackish water for irrigation, and poor tillage operations, are the foremost causes of soil salinization. Typical characteristics of saline soils are salt stress, high pH, and lack of organic carbon, as well as low availability of nutrients. Disruption of precipitation patterns as well as high average annual temperatures due to climate change additionally negatively affects the process of soil salinization. Productivity and ability to support crop growth are reduced on saline soil. Salinity-induced stress reduces plant growth by modulating the antioxidative system and nutrient orchestration. The aim of this work is to show that the mentioned problems can be alleviated in several ways such as the addition of biochar, exogenous application of several elicitors, seed priming, etc. Research has shown that the addition of biochar can significantly improve the recovery of saline soil. The addition of biochar has no significant effect on soil pH, while the cation exchange capacity of the soil increased by 17%, and the electrical conductivity of the saturated paste extract decreased by 13.2% (depends on the initial salinity and the type of biochar raw material). Moreover, biochar enriched with silicon increases the resistance of bananas to salt stress. In addition, exogenous application of several elicitors helps plants to alleviate stress by inducing stress-related physicochemical and molecular changes (selenium, sulfur, silicon, salicylic acid). Finally, seed priming showed positive effects on metabolomics, proteomics and growth of plants subjected to abiotic stress. Priming usually involves immersing the seed in a solution for a period of time to induce physiological and metabolic progression prior to germination.

Effect of CO_(2)exposure on the mechanical strength of geopolymerstabilized sandy soils

In recent years,there has been growing interest in developing methods for mitigating greenhouse effect,as greenhouse gas emissions continue to contribute to global temperature rise.On the other hand,investigating geopolymers as environmentally friendly binders to mitigate the greenhouse effect using soil stabilization has been widely conducted.However,the effect of CO_(2)exposure on the mechanical properties of geopolymer-stabilized soils is rarely reported.In this context,the effect of CO_(2)exposure on the mechanical and microstructural features of sandy soil stabilized with volcanic ash-based geopolymer was investigated.Several factors were concerned,for example the binder content,relative density,CO_(2)pressure,curing condition,curing time,and carbonate content.The results showed that the compressive strength of the stabilized sandy soil specimens with 20%volcanic ash increased from 3 MPa to 11 MPa.It was also observed that 100 kPa CO_(2)pressure was the optimal pressure for strength development among the other pressures.The mechanical strength showed a direct relationship with binder content and carbonate content.Additionally,in the ambient curing(AC)condition,the mechanical strength and carbonate content increased with the curing time.However,the required water for carbonation evaporated after 7 d of oven curing(OC)condition and as a result,the 14-d cured samples showed lower mechanical strength and carbonate content in comparison with 7-d cured samples.Moreover,the rate of strength development was higher in OC cured samples than AC cured samples until 7 d due to higher geopolymerization and carbonation rate.

Multivariate Approach to Characterizing Soil Quality of Gabonese’s Ferralitic Soils

Assessing soil quality is essential for crop management and soil temporal changes. The present study aims to evaluate soil quality in the Ferralitic soils context countrywide. This assessment was done using multivariate soil quality indice (SQI) models, such as additive quality index (AQI), weighted quality indexes (WQIadd and WQIcom) and Nemoro quality index (NQI), applied to two approaches of indicator selection: total data set (TDS) and minimum data set (MDS). Physical and chemical soil indicators were extracted from the ORSTOM’s reports resulting from a sampling campaign in different provinces of Gabon. The TDS approach shows soil quality status according to eleven soil indicators extracted from the analysis of 1,059 samples from arable soil layer (0 - 30 cm depth). The results indicated that 87% of all provinces presented a very low soil quality (Q5) whatever the model. Among soil indicators, exchangeable K+ and Mg2+, bulk density and C/N ratio were retained in MDS, using principal component analysis (PCA). In the MDS approach, 50 to 63% of provinces had low soil quality grades with AQI, WQIadd and NQI, whereas the total was observed with WQIcom. Only 25% of provinces had medium soil quality grades with AQI and NQI models, while 12.5% (NQI) and 25% (AQI) presented high quality grades. Robust statistical analyses confirmed the accuracy and validation (0.80 r P ≤ 0.016) of AQI, WQIadd and NQI into the TDS and MDS approaches. The same sensitivity index value (1.53) was obtained with AQI and WQIadd. However, WQIadd was chosen as the best SQI model, according to its high linear regression value (R2 = 0.82) between TDS and MDS. This study has important implications in decision-making on monitoring, evaluation and sustainable management of Gabonese soils in a pedoclimatic context unfavorable to plant growth.

At-rest lateral earth pressure of compacted expansive soils:Experimental investigations and prediction approach

This paper presents experimental studies on a compacted expansive soil,from Nanyang,China for investigating the at-rest lateral earth pressureσL of expansive soils.The key studies include(i)relationships between theσL and the vertical stressσV during soaking and consolidation,(ii)the influences of initial dry densityρd0 and moisture content w 0 on the vertical and lateral swelling pressures at no swelling strain(i.e.σV0 andσL0),and(iii)evolution of theσL during five long-term wetting-drying cycles.Experimental results demonstrated that the post-soakingσL-σV relationships are piecewise linear and their slopes in the passive state(σL>σV)and active state(σL<σV)are similar to that of the consolidationσL-σV relationships in the normal-and over-consolidated states,respectively.The soakingσL-σV relationships converge to the consolidationσL-σV relationships at a thresholdσV where the interparticle swelling is restrained.TheσL0 andσV0 increase monotonically withρd0;however,they show increasing-then-decreasing trends with the w 0.The extent of compaction-induced swelling anisotropy,which is evaluated byσL0/σV0,reduces with an increase in the compaction energy and molding water content.TheσL reduces over moisture cycles and the stress relaxation in theσL during soaking is observed.An approach was developed to predict the at-rest soakingσL-σV relationships,which requires conventional consolidation and shear strength properties and one measurement of theσL-σV relationships during soaking.The proposed approach was validated using the results of three different expansive soils available in the literature.

Physico-chemical properties and macrofauna of soils under various farming systems of cold arid region in Balochistan,Pakistan

Barshore is a small village in the Pishin District,Balochistan,Pakistan,with dry summers and cold rainy winters.This is an agrarian region,mostly with orchards of various fruit trees.This study investigated the physico-chemical properties and macrofauna of soils under various agricultural management practices of this region.The concentrations of soil organic matter(SOM),soil organic carbon(SOC),nutrients,pH,electrical conductivity,soil texture,and the abundance and number of species of soil macrofauna of the agricultural fields were measured.Fifteen agricultural fields were sampled.Fourteen fields were orchards of apple,apricot or the mixture of apple and apricot trees and one field was a cropland,cultivated with wheat as a monocrop.The orchards were under conservation agricultural practices;whereas,the cropland was under conventional management.These agricultural lands were 2-26 years old.The concentration of soil organic matter(SOM)in the upper 0-10 cm depth of these field sites ranged from 11.6 g kg^(-1)to 32.8 g kg^(-1)soil.As compared to cropland,orchards had significantly higher concentration of SOM and SOC.A total of 18 soil macrofauna species were found and the most common and abundant were ants(Monomorium minimum,Camponotus pennsylvanicus,Solenopsis invicta,and Lasius niger)followed by Arion ssp.(Brown Slug)and earthworm Lumbricus terrestris.Regression analysis revealed non-significant relationship of the age and the concentration of SOM with the number of macrofauna species and with the concentrations of total mineral nitrogen,bioavailable phosphorus and clay.The existence of ants had no relationship with the concentration of SOM;whereas,existence of Lumbricus terrestris tended to had a positive relationship with the concentration of SOM.The field of tree-based intercropping system was 2 years of age since the land was converted from rangeland to a cropland,had two ant species coexisting.This indicates the positive influence of crop diversification on soil macrofauna.

Evaluation of the Level of Pollution by Heavy Metals of Market Garden Soils along the Chari River in Ndjamena: Case of the 9th and 7th Districts

The main aim of this study was to characterize the metal content of soils used for market gardening along the Chari river: the 7th and 9th districts of NDjaména. To achieve this, two sites were selected: Gassi and Walia, and two control sites (Gassi and Walia). A total of fifty (50) soil samples were taken (24 from the Gassi site, 24 from the Walia site and 2 as control soils) and then analyzed to determine a number of physico-chemical parameters (pH, OM and electrical conductivity) and heavy metal concentrations in the various soils. The TME content (As, Cd, Cu, Cr, Ni, Pb, Hg and Zn) of the soils was determined by plasma-coupled Atomic Emission Spectrometry. In order to assess the level of contamination in Gassi and Walia soils, the geoaccumulation index (GeoIndex), contamination factor and degree of contamination were calculated. Results for physico-chemical parameters revealed that pH ranged from acidic (4.6) to moderately neutral (6.5), electrical conductivity was higher in cultivated soils (mean 292.14 μs/cm) than in control soils (mean 149.33 μs/cm), and soils were rich in organic matter. Overall, heavy metal concentrations in cultivated soils were higher than in control soils. The pollution estimate shows that soils in the area have no moderate contamination. The increase in TME concentrations in cultivated soils is thought to be due to the input of agricultural inputs to the soil. However, these levels are below the Average shale reference and Canadian guidelines for agricultural soil quality. Principal component analysis shows that metals are positively and significantly correlated with each other, and negatively and moderately significantly correlated with each other.

Modelling rapid non-destructive test using light weight deflectometer on granular soils across different degrees of saturation

This study introduces an advanced finite element model for the light weight deflectometer(LWD),which integrates contact mechanics with fully coupled models.By simulating LWD tests on granular soils at various saturation levels,the model accurately reflects the dependence of the LWD modulus on dry density,water content,and effective stress.This model addresses and overcomes the limitations of previous finite element models for this specific problem.Simultaneously,this research presents the first experimentally validated fully coupled contact impact model.Furthermore,the research provides a comparative assessment of elastoplastic and nonlinear elastic models and contrasts an enriched node-tosegment method(developed in this study)with the more precise mortar technique for contact mechanics.These comparisons reveal unique advantages and challenges for each method.Moreover,the study underscores the importance of careful application of the LWD modulus,emphasising the need for sophisticated tools to interpret soil behaviour accurately.