An InP optical 90°hybrid based on a×4 MMI coupler with a deep ridged waveguide is designed and fabricated.The working principle of the 90°hybrid is systematically introduced.Three-dimensional beam ropag...An InP optical 90°hybrid based on a×4 MMI coupler with a deep ridged waveguide is designed and fabricated.The working principle of the 90°hybrid is systematically introduced.Three-dimensional beam ropagation method(3D BPM)is used to optimize the structure parameters of the 90°hybrid.The designed compact structure is demonatrated to have a low excess loss less than-0.15 dB,a high common mode rejection ratio better than 40 dB,and a low relative phase deviation less than±2.5°.The designed hybrid is manufactured on a sandwitched structure deposited on an InP substrate.The measured results show that the common mode rejection ratios are larger than 20 dB in a range from 1520 nm to 1580 nm.The phase deviations are less than±5°in a range from 1545 nm to 1560 nm and less than±7°across the C band.The designed 90°optical hybrid is suitable well for realizing miniaturization,high-properties,and high bandwidth of coherent receiver.展开更多
[Objectives] To analyze the similarities of Boenninghausenia sessilicarpa Levl. and Boenninghausenia albiflora(Hook.) Meiss by the common and variant peak ratio dual indicator sequence method. [Methods] Four different...[Objectives] To analyze the similarities of Boenninghausenia sessilicarpa Levl. and Boenninghausenia albiflora(Hook.) Meiss by the common and variant peak ratio dual indicator sequence method. [Methods] Four different solvents(petroleum ether, chloroform, ethyl acetate and methanol) were used to extract the chemical components of different polar regions of B. sessilicarpa and B. albiflora. UV-visible spectrophotometry(second derivative method) was used to collect the fingerprints of different solvent extracts, and common and variant peak peak ratios were analyzed for the absorption peak data. [Results] The common peak ratio and variant peak ratio data of ground parts of B. albiflora and B. sessilicarpa was S2∶S5(46.2(54.2, 62.5)), compared with the data of other groups, the common peak ratio was the largest, thus the components of ground parts of B. albiflora and B. sessilicarpa were closest and had the largest similarities; the common peak ratio and variant peak ratio data of the components extracted by chloroform from B. albiflora and B. sessilicarpa was Y2∶Y6(54.2(38.5, 46.2)), compared with the data of other groups, the variant peak ratio was the smallest, thus, the chemical components near the chloroform polarity of two kinds of medicinal materials had the largest similarities and smallest differences. [Conclusions] This method is simple and easy to operate, and the ultraviolet fingerprint data of four different polar organic solvent extracts are used for comprehensive analysis, and the results have high specificity and high accuracy. Besides, there are certain similarities and also differences between the chemical components of B. sessilicarpa and B. albiflora. It is expected to provide a new evaluation method for the variety quality of B. sessilicarpa and B. albiflora.展开更多
An approach is recommended for the correction of common Pb contribution to \{\{\}\+\{207\}Pb\}/\{\{\}\+\{206\}Pb\} ages obtained by the zircon evaporation technique. A comparison with that by Cocherie et al. (1992) sh...An approach is recommended for the correction of common Pb contribution to \{\{\}\+\{207\}Pb\}/\{\{\}\+\{206\}Pb\} ages obtained by the zircon evaporation technique. A comparison with that by Cocherie et al. (1992) shows that two approaches yield similar results in the \{\{\}\+\{207\}Pb\}*/\{\{\}\+\{206\}Pb\}* ratios. But when using the new approach, only two errors of the measured \{\{\}\+\{204\}Pb\}/\{\{\}\+\{206\}Pb\} and \{\{\}\+\{207\}Pb\}/\{\{\}\+\{206\}Pb\} ratios are introduced to the calculated \{\{\}\+\{207\}Pb\+*\}/\{\{\}\+\{206\}Pb\+*\} ratios.展开更多
As is known to all, grinding force is one of the most important parameters to evaluate the whole process of grinding. Generally, the grinding force is resolved to three component forces, namely, normal grinding force ...As is known to all, grinding force is one of the most important parameters to evaluate the whole process of grinding. Generally, the grinding force is resolved to three component forces, namely, normal grinding force F n, tangential grinding force F t and a component force acting along the direction of longitudinal feed which is usually neglected because of insignificance. The normal grinding force F n has influence upon surface deformation and roughness of workpiece, while the tangential grinding force F t mainly affect power consumption and service life of grinding wheel. In order to study deep into the process of the unsteady state grinding, we set up a measurement system to monitor the change of grinding force during the course of grinding and try to find some difference in the change of grinding force between the steady state grinding and unsteady state grinding. In the test, the normal and tangential grinding forces, F n and F t were measured by using a set of equipments including sensor, amplifier, oscilloscope and computer monitor. From the results, we can conclude that: 1) In the unsteady state grinding process, the values of the grinding forces are much lower than those of the steady state grinding process and the grinding force ratio showed a nonlinear fluctuation. 2) The tendency of the grinding forces in the process of the unsteady state grinding proved the existence of the cutting and micro-cutting actions. 3) Because the grinding force signals of the unsteady state grinding are much weaker than those of the steady state grinding, to obtain accurate value of the grinding forces, wave filtering is needed to be done. The whole process to filter the perturbation wave can be separated into three steps in order, changing the grinding force signals from analog signals into digital signals, FFT (fast Fourier transform) treatment to the digital signals, and IFFT(inversion fast Fourier transform) treatment to the digital signals after spectrum limitation.展开更多
This work gives an analytical theory of the signal-to-thermal-noise ratio (SNR) of classical Hall plates with four contacts at small magnetic field. In contrast to previous works, the symmetry of the Hall plates is re...This work gives an analytical theory of the signal-to-thermal-noise ratio (SNR) of classical Hall plates with four contacts at small magnetic field. In contrast to previous works, the symmetry of the Hall plates is reduced to only a single mirror axis, whereby the average of potentials of the two output contacts off this mirror axis differs from the average of potentials at the two supply contacts on the mirror axis, i.e. the output common mode differs from 50%. Surprisingly, at fixed power dissipated in the Hall plate, the maximum achievable SNR is only 9% smaller for output common modes of 30% and 70% when compared to the overall optimum at output common modes of 50%. The theory is applied to Vertical Hall effect devices with three contacts on the top surface and one contact being the buried layer in a silicon BiCMOS process. Geometries are found with large contacts and only a moderate loss in SNR.展开更多
基金Project supported by the National Key Research and Development Program of China(Grant No.2016YFB0402404)the Beijing Natural Science Foundation,China(Grant No.4194093)the National Natural Science Foundation of China(Grant Nos.61635010,61674136,and 61435002).
文摘An InP optical 90°hybrid based on a×4 MMI coupler with a deep ridged waveguide is designed and fabricated.The working principle of the 90°hybrid is systematically introduced.Three-dimensional beam ropagation method(3D BPM)is used to optimize the structure parameters of the 90°hybrid.The designed compact structure is demonatrated to have a low excess loss less than-0.15 dB,a high common mode rejection ratio better than 40 dB,and a low relative phase deviation less than±2.5°.The designed hybrid is manufactured on a sandwitched structure deposited on an InP substrate.The measured results show that the common mode rejection ratios are larger than 20 dB in a range from 1520 nm to 1580 nm.The phase deviations are less than±5°in a range from 1545 nm to 1560 nm and less than±7°across the C band.The designed 90°optical hybrid is suitable well for realizing miniaturization,high-properties,and high bandwidth of coherent receiver.
基金Supported by State Key Research and Development Program of Ministry of Science and Technology(2018YFC1708000)Scientific and Technological Project at Department and Bureau Level(2018JC028)Fundamental Research Funds for the Central Universities of Southwest Minzu University(2018NQN13)
文摘[Objectives] To analyze the similarities of Boenninghausenia sessilicarpa Levl. and Boenninghausenia albiflora(Hook.) Meiss by the common and variant peak ratio dual indicator sequence method. [Methods] Four different solvents(petroleum ether, chloroform, ethyl acetate and methanol) were used to extract the chemical components of different polar regions of B. sessilicarpa and B. albiflora. UV-visible spectrophotometry(second derivative method) was used to collect the fingerprints of different solvent extracts, and common and variant peak peak ratios were analyzed for the absorption peak data. [Results] The common peak ratio and variant peak ratio data of ground parts of B. albiflora and B. sessilicarpa was S2∶S5(46.2(54.2, 62.5)), compared with the data of other groups, the common peak ratio was the largest, thus the components of ground parts of B. albiflora and B. sessilicarpa were closest and had the largest similarities; the common peak ratio and variant peak ratio data of the components extracted by chloroform from B. albiflora and B. sessilicarpa was Y2∶Y6(54.2(38.5, 46.2)), compared with the data of other groups, the variant peak ratio was the smallest, thus, the chemical components near the chloroform polarity of two kinds of medicinal materials had the largest similarities and smallest differences. [Conclusions] This method is simple and easy to operate, and the ultraviolet fingerprint data of four different polar organic solvent extracts are used for comprehensive analysis, and the results have high specificity and high accuracy. Besides, there are certain similarities and also differences between the chemical components of B. sessilicarpa and B. albiflora. It is expected to provide a new evaluation method for the variety quality of B. sessilicarpa and B. albiflora.
文摘An approach is recommended for the correction of common Pb contribution to \{\{\}\+\{207\}Pb\}/\{\{\}\+\{206\}Pb\} ages obtained by the zircon evaporation technique. A comparison with that by Cocherie et al. (1992) shows that two approaches yield similar results in the \{\{\}\+\{207\}Pb\}*/\{\{\}\+\{206\}Pb\}* ratios. But when using the new approach, only two errors of the measured \{\{\}\+\{204\}Pb\}/\{\{\}\+\{206\}Pb\} and \{\{\}\+\{207\}Pb\}/\{\{\}\+\{206\}Pb\} ratios are introduced to the calculated \{\{\}\+\{207\}Pb\+*\}/\{\{\}\+\{206\}Pb\+*\} ratios.
文摘As is known to all, grinding force is one of the most important parameters to evaluate the whole process of grinding. Generally, the grinding force is resolved to three component forces, namely, normal grinding force F n, tangential grinding force F t and a component force acting along the direction of longitudinal feed which is usually neglected because of insignificance. The normal grinding force F n has influence upon surface deformation and roughness of workpiece, while the tangential grinding force F t mainly affect power consumption and service life of grinding wheel. In order to study deep into the process of the unsteady state grinding, we set up a measurement system to monitor the change of grinding force during the course of grinding and try to find some difference in the change of grinding force between the steady state grinding and unsteady state grinding. In the test, the normal and tangential grinding forces, F n and F t were measured by using a set of equipments including sensor, amplifier, oscilloscope and computer monitor. From the results, we can conclude that: 1) In the unsteady state grinding process, the values of the grinding forces are much lower than those of the steady state grinding process and the grinding force ratio showed a nonlinear fluctuation. 2) The tendency of the grinding forces in the process of the unsteady state grinding proved the existence of the cutting and micro-cutting actions. 3) Because the grinding force signals of the unsteady state grinding are much weaker than those of the steady state grinding, to obtain accurate value of the grinding forces, wave filtering is needed to be done. The whole process to filter the perturbation wave can be separated into three steps in order, changing the grinding force signals from analog signals into digital signals, FFT (fast Fourier transform) treatment to the digital signals, and IFFT(inversion fast Fourier transform) treatment to the digital signals after spectrum limitation.
文摘This work gives an analytical theory of the signal-to-thermal-noise ratio (SNR) of classical Hall plates with four contacts at small magnetic field. In contrast to previous works, the symmetry of the Hall plates is reduced to only a single mirror axis, whereby the average of potentials of the two output contacts off this mirror axis differs from the average of potentials at the two supply contacts on the mirror axis, i.e. the output common mode differs from 50%. Surprisingly, at fixed power dissipated in the Hall plate, the maximum achievable SNR is only 9% smaller for output common modes of 30% and 70% when compared to the overall optimum at output common modes of 50%. The theory is applied to Vertical Hall effect devices with three contacts on the top surface and one contact being the buried layer in a silicon BiCMOS process. Geometries are found with large contacts and only a moderate loss in SNR.
