Finite Element Analysis for In-Plane Crushing Behaviour of Aluminium Honeycombs

A number of finite element simulations were performed to analyze the in-plane crushing behaviour of aluminium honeycombs and the results are presented and discussed. The simulations include both X1 and X2 cases. All the analyses are quasi-static, and can be divided into three groups, which are designed to investigate the effects of cell size, foil thickness and yield stress of the foil material, respectively, on the structural response of honeycombs. The result indicates that these factors can significantly affect the plateau stresses of honeycomb cellular structures in both directions, and the plateau stresses in X2 direction are slightly smaller than those in X1 direction. The simulation results were further compared with published theoretical predictions and show higher values. The difference was then analyzed and a new expression for the plateau stress of honeycombs was suggested.

The coupled hydro-mechanical behaviours of compacted crushed Callovo-Oxfordian argillite

Callovo-Oxfordian （COx） argillite obtained from the excavation of high-level radioactive waste geological disposal has been evaluated as an alternative sealing/backfill material in France. This paper presents an experimental investigation into the hydro-mechanical behaviour of compacted crushed COx argillite. A series of oedorneter compressive tests including various loading-unloading cycles were conducted on COx argillite powders at different initial water contents. After reaching the desired dry density （2.0 Mg/m^3）, the vertical stress was reduced to different levels （7.0 and 0.5 MPa） and the compacted sample was then flooded under constant volume conditions while measuring the changes in the vertical stress. It was found that the initial water content significantly affects the compressive behaviour. The measured saturated hydraulic conductivity is less than 1×10^-10m/s.

Compressive Behaviours of Concrete Cylinders Wrapped with 2-D Glass Fabrics

Concrete cylindess wrapped with glass fabrics of various constructions were fabricated. Compressive behaviours of cylinders with and without fabric wrapping were investigated. Comparisons of the compressive characters while using different fabrication parameters were made. It was demonstrated that the effect of the fabric reinforcent was obvious. The tensile strength of the filament used in the fabric played an important role as far as the anti-compression behaviour of the reinforced cylinders is concened.

Effect of hydrogen addition on compression deformation behaviour of Ti-0.3Mo-0.8Ni alloy argon-arc welded joints

The effect of hydrogen addition on compression deformation behaviour of Ti-0.3Mo-0.8Ni alloy argon-arc welded joint has been investigated.Evolution mechanism of hydrogen-induced flow stress was discussed in detail.The results show that with increasing hydrogen content,the stretching and bending extent of fully lamellar microstructures including ot lamellas and acicular hydride continued to increase,the morphology of dynamic recrystallization(DRX)grains tended to change from approximately equiaxed to large lamellar shape,and the quantity of DRX grains and recrystallization degree of grains increased obviously.A large number of dislocations concentrated in the vicinity of the hydride.Steady stress was decreased continuously with increasing hydrogen content,while peak stress of the hydrogenated 0.12 wt.% H weld zone was decreased to the minimum value and then increased slowly.A slight decrease in flow stress of the hydrogenated 0.05 wt.% H weld zone was caused by limited increase in the volume fraction of softer βphase.Hydrogen-induced DRX of a phase and improved dislocation movement by strong interaction between the hydride and dislocation directly resulted in a sharp drop in flow stress of the hydrogenated 0.12 and 0.21 wt.% H weld zone.Solute hydrogen also finitely contributed to a sharp drop in flow stress of the hydrogenated 0.12 and 0.21 wt.% H weld zone by promoted local softening,which induced continuous DRX and more movable dislocations to participate in slipping or climbing.The reinforcement effect and plastic deformation of the hydride and solution strengthening of P phase induced by solute hydrogen finally led to the increase in flow stress of the hydrogenated 0.21 wt.% H weld zone in its true strain range from 0 to 0.36.

OUT-OF-PLANE COMPRESSIVE PROPERTIES OF HEXAGONAL PAPER HONEYCOMBS

The compressive behaviour of paper honeycombs is studied by means of an experimental analysis. Experiment results show how geometry aspects of hexagonal paper honeycombs, e.g. the height of paper honeycomb, the thickness and length of honeycomb cell-wall, the drawing ratio of hexagonal honeycomb, affect the compressive properties of the paper honeycombs. It is in good agreement with the theory model. The constraint factor K of the critical buckling stress is mainly determined by the length of honeycomb cell-wail. It can be described as K=1.54 for B type paper honeycombs and K=3.32 for D type paper honeycombs. The plateau stress is the power exponent function of the thickness to length ratio of honeycomb cell-wall, and the experiment results show that the constant is 13.2 and the power exponent is 1.77. The research results can be used to characterize and improve efficiently the compressive properties of paper honeycombs.