Determination of Material Parameters of EVA Foam under Uniaxial Compressive Testing Using Hyperelastic Models

The objective of this research was to determine the mechanical parameter from EVA foam and also investigate its behavior by using Blatz-Ko,Neo-Hookean,Mooney model and experimental test.The physical characteristic of EVA foam was also evaluated by scanning electron microscopy(SEM).The results show that Blatz-Ko and Neo-Hookean model can fit the curve at 5%and 8%strain,respectively.The Mooney model can fit the curve at 50%strain.The modulus of rigidity evaluated from Mooney model is 0.0814±0.0027 MPa.The structure of EVA foam from SEM image shows that EVA structure is a closed cell with homogeneous porous structure.From the result,it is found that Mooney model can adjust the data better than other models.This model can be applied for mechanical response prediction of EVA foam and also for reference value in engineering application.

Finite element analysis of small-scale hot compression testing

This paper models hot compression testing using a dilatometer in loading mode.These small-scale tests provide a high throughput at low cost,but are susceptible to inhomogeneity due to friction and temperature gradients.A novel method is presented for correcting the true stress-strain constitutive response over the full range of temperatures,strain-rates and strain.The nominal response from the tests is used to predict the offset in the stress-strain curves due to inhomogeneity,and this stress offsetΔσis applied piecewise to the data,correcting the constitutive response in one iteration.A key new feature is the smoothing and fitting of the flow stress data as a function of temperature and strain-rate,at multiple discrete strains.The corrected model then provides quantitative prediction of the spatial and temporal variation in strain-rate and strain throughout the sample,needed to correlate the local deformation conditions with the microstructure and texture evolution.The study uses a detailed series of 144 hot compression tests of a Zr-Nb alloy.While this is an important wrought nuclear alloy in its own right,it also serves here as a test case for modelling the dilatometer for hot testing of high temperature alloys,particularly those with dualα-βphase microstructures(such as titanium alloys).

Evaluation of granule structure and strength properties of green packed beds in iron ore sintering using high-resolution X-ray tomography and uniaxial compression testing

The strength properties of green sinter beds,including the Young’s modulus and maximum bed strain,were evaluated using uniaxial compression tests.The green-sinter-bed samples were scanned using X-ray computed tomography(XCT),and the geometry characteristics of the granules were quantified by XCT image analysis.The orthogonal array method was applied to determine the concomitant effects of the moisture,hydrated lime,and concentrate contents on the bed strength characteristics.Less bed strain was observed when the granules had a thin adhering layer and increased interlock contacts,which had a great capacity to resist the applied load collectively.The optimal combination for decreasing the bed maximum strain was 5.8%moisture,2%hydrated lime,and 0%concentrate.The moisture and concentrate contents were the most significant factors determining the green bed strength.Increasing the moisture and concentrate contents produced granules with a thicker and more deformable adhering layer,resulting in a more compact bed.The addition of hydrated lime inhibited rearrangement,deformation,and fracture of the granules in green sinter bed during compression.

Particle simulation of the failure process of brittle rock under triaxial compression

In order to investigate the failure process of brittle rock under triaxial compression through both experimental and numerical approaches, the particle simulation method was used in numerical simulations and the simulated results were compared with those of the experiment. The numerical simulation results, such as fracture propagation, microcrack distribution, stress-strain response, and damage patterns, were discussed in detail. The simulated results under various confining pressures （0-60 MPa） are in good agreement with the experimental results. The simulated results reveal that rock failure is caused by axial splitting under uniaxial compression. As the confining pressure increases, rock failure occurs in a few localized shear planes and the rock mechanical behavior is changed from brittle to ductile. Consequently, the peak failure strength, microcrack numbers, and the shear plane angle increase, but the ratio of tensile to shear microcracks decreases. The damage formation during the compression simulations indicates that the particle simulation method can produce similar behaviors as those observed through laboratory compression tests.

Constitutive relationship of IN690 superalloy by using uniaxial compression tests

The hot deformation behavior of IN690 superalloy was characterized in a temperature range of 1273-1473 K and a strain rate range of 0.01-10 s^-1 using uniaxial compression tests on process annealed material.The constitutive relations between flow stress and effective strain,effective strain rate as well as deformation temperature were studied.It can be concluded that the flow stress significantly reduces with the deformation temperature of IN690 superalloy increasing.Whereas,there is a significant increase of flow stress when the strain rate increases from 0.1 s^-1 to 10 s^-1.Based on the hyperbolic-sine Arrhenius-type equation,a constitutive equation considering compensation of strain was developed.The activation energy and the material constants（Q,n and ln A） decrease as the deformation strain increases.The strain dependent term is successfully incorporated in the constitutive equation through a quartic equation.A good agreement between the experimental data and the predicted results has been achieved,indicating that the proposed constitutive equation and the methods of determing the material constants are suitable to model the high temperature deformation behavior of IN690 superalloy.

Three-dimensional finite element simulation and reconstruction of jointed rock models using CT scanning and photogrammetry

The geometry of joints has a significant influence on the mechanical properties of rocks.To simplify the curved joint shapes in rocks,the joint shape is usually treated as straight lines or planes in most laboratory experiments and numerical simulations.In this study,the computerized tomography (CT) scanning and photogrammetry were employed to obtain the internal and surface joint structures of a limestone sample,respectively.To describe the joint geometry,the edge detection algorithms and a three-dimensional (3D) matrix mapping method were applied to reconstruct CT-based and photogrammetry-based jointed rock models.For comparison tests,the numerical uniaxial compression tests were conducted on an intact rock sample and a sample with a joint simplified to a plane using the parallel computing method.The results indicate that the mechanical characteristics and failure process of jointed rocks are significantly affected by the geometry of joints.The presence of joints reduces the uniaxial compressive strength (UCS),elastic modulus,and released acoustic emission (AE) energy of rocks by 37%–67%,21%–24%,and 52%–90%,respectively.Compared to the simplified joint sample,the proposed photogrammetry-based numerical model makes the most of the limited geometry information of joints.The UCS,accumulative released AE energy,and elastic modulus of the photogrammetry-based sample were found to be very close to those of the CT-based sample.The UCS value of the simplified joint sample (i.e.38.5 MPa) is much lower than that of the CT-based sample (i.e.72.3 MPa).Additionally,the accumulative released AE energy observed in the simplified joint sample is 3.899 times lower than that observed in the CT-based sample.CT scanning provides a reliable means to visualize the joints in rocks,which can be used to verify the reliability of photogrammetry techniques.The application of the photogrammetry-based sample enables detailed analysis for estimating the mechanical properties of jointed rocks.

Fundamental Study on Response Properties of Structures Constructed on Lunar Regolith

The Artemis Program, for constructing the lunar base, is in progress. How to design and construct architectural and civil engineering structures in the lunar environment has become an important issue. The lunar surface is covered with soft sand, called regolith, and it is required to protect lunar bases and structures, as well as internal precision equipment, against vibrational disturbances such as moonquakes and meteorite collisions. Therefore, in this study, the static and cyclic triaxial compression tests of the regolith simulant were conducted. The reference strain and equivalent damping factor of the regolith simulant were smaller compared to sandy soil on Earth. In addition, a shaking table test using model specimens was conducted on the response properties of regolith ground alone and structures set on regolith ground. The buried foundation and pile foundation notably suppressed the horizontal response attributed to the rocking component compared to a direct foundation.

Experimental study on cracking behaviour of moulded gypsum containing two non-parallel overlapping flaws under uniaxial compression

Failure of rock mass that is subjected to compressive loads occurs from initiation, propagation, and linkage of new cracks from preexisting fissures. Our research investigates the cracking behaviour and coalescence process in a brittle material with two non-parallel overlapping flaws using a high-speed camera. The coalescence tensile crack and tensile wing cracks were the first cracks to occur from the preexisting flaws. The initiation stresses of the primary cracks at the two tips of each flaw were simultaneous and decreased with reduced flaw inclination angle. The following types of coalescence cracks were identified between the flaws: primary tensile coalescence crack, tensile crack linkage, shear crack linkage, mixed tensile-shear crack, and indirect crack coalescence. Coalescence through tensile linkage occurred mostly at pre-peak stress. In contrast, coalescence through shear or mixed tensile-shear cracks occurred at higher stress. Overall, this study indicates that the geometry of preexisting flaws affect crack initiation and coalescence behaviour.

Specimen aspect ratio and progressive field strain development of sandstone under uniaxial compression by three-dimensional digital image correlation

The complete stress-strain characteristics of sandstone specimens were investigated in a series of quasistatic monotonic uniaxial compression tests.Strain patterns development during pre-and post-peak behaviours in specimens with different aspect ratios was also examined.Peak stress,post-peak portion of stress-strain,brittleness,characteristics of progressive localisation and field strain patterns development were affected at different extents by specimen aspect ratio.Strain patterns of the rocks were obtained by applying three-dimensional(3D) digital image correlation(DIC) technique.Unlike conventional strain measurement using strain gauges attached to specimen,3D DIC allowed not only measuring large strains,but more importantly,mapping the development of field strain throughout the compression test,i.e.in pre-and post-peak regimes.Field strain development in the surface of rock specimen suggests that strain starts localising progressively and develops at a lower rate in pre-peak regime.However,in post-peak regime,strains increase at different rates as local deformations take place at different extents in the vicinity and outside the localised zone.The extent of localised strains together with the rate of strain localisation is associated with the increase in rate of strength degradation.Strain localisation and local inelastic unloading outside the localised zone both feature post-peak regime.

Shape ratio effects on the mechanical characteristics of rectangular prism rocks and isolated pillars under uniaxial compression

Isolated pillars in underground mines are subjected to uniaxial stress,and the load bearing cross-section of pillars is commonly rectangularly shaped.In addition,the uniaxial compression test(UCT)is widely used for determining the basic mechanical properties of rocks and revealing the mechanism of isolated pillar disasters under unidimensional stress.The shape effects of rock mechanical properties under uniaxial compression are mainly quantitatively reflected in the specific shape ratios of rocks.Therefore,it is necessary to study the detailed shape ratio effects on the mechanical properties of rectangular prism rock specimens and isolated pillars under uniaxial compressive stress.In this study,granite,marble and sandstone rectangular prism specimens with various height to width ratios(r)and width to thickness ratios(u)were prepared and tested.The study results show that r and u have a great influence on the bearing ability of rocks,and thin or high rocks have lower uniaxial compressive strength.Reducing the level of r can enhance the u effect on the strength of rocks,and increasing the level of u can enhance the r effect on the strength of rocks.The lateral strain on the thickness side of the rock specimen is larger than that on the width side,which implies that crack growth occurs easily on the thickness side.Considering r and u,a novel strength prediction model of isolated pillars was proposed based on the testing results,and the prediction model was used for the safety assessment of 179 isolated pillars in the Xianglu Mountain Tungsten Mine.

Temperature-controlled triaxial compression/creep test device for thermodynamic properties of soft sedimentary rock and corresponding theoretical prediction

In deep geological disposal of high-level nuclear waste,one of the most important subjects is to estimate long-term stability and strength of host rock under high temperature conditions caused by radioactive decay of the waste.In this paper,some experimental researches on the thermo-mechanical characteristics of soft sedimentary rock have been presented.For this reason,a new temperature-controlled triaxial compression and creep test device,operated automatically by a computer-controlled system,whose control software has been developed by the authors,was developed to conduct the thermo-mechanical tests in different thermal loading paths,including an isothermal path.The new device is proved to be able to conduct typical thermo-mechanical element tests for soft rock.The test device and the related testing method were introduced in detail.Finally,some test results have been simulated with a thermo-elasto-viscoplastic model that was also developed by the authors.

EFFECTS OF STRAIN RATE ＆TEMPERATURE ON HOT COMPRESSION FLOW BEHAVIOR OF A HYDROGENATED CAST Ti－25Al－

The flow behavior of a cast Ti-25Al-10Nb-3V-1Mo alloy based onTi3Al, with and without hydrogen content, was investigated under isothermal compression test at strain rates of 0.1s-1 to 0.001s -1 in the temperature range of 900℃ to1000 ℃. The hot compression peak stress (or the maximum flow stress) of the alloy withand without hydrogen decreases with the increasing temperature and the decreasingstrain rate. Hydrogenation makes the hot compression peak stress decrease by 37%～53%, which corresponds to lowering the deformation temperature by about 50℃.Strain rate does not change the favorable effect of hydrogenation on hot compressionflow behavior at all three deformation temperatures. The microstructure of the alloywith 0.2% H (mass %) deformed at a fixed temperature exhibits the same feature asthat of the alloys without hydrogenation deformed at higher temperatures for bothstrain rates. Hydrogenation has the same effect on microstructure as strain rate andtemperature.

System-on-Chip Test Data Compression Based on Split-Data Variable Length (SDV) Code

System-on-a-chips with intellectual property cores need a large volume of data for testing. The large volume of test data requires a large testing time and test data memory. Therefore new techniques are needed to optimize the test data volume, decrease the testing time, and conquer the ATE memory limitation for SOC designs. This paper presents a new compression method of testing for intellectual property core-based system-on-chip. The proposed method is based on new split- data variable length (SDV) codes that are designed using the split-options along with identification bits in a string of test data. This paper analyses the reduction of test data volume, testing time, run time, size of memory required in ATE and improvement of compression ratio. Experimental results for ISCAS 85 and ISCAS 89 Benchmark circuits show that SDV codes outperform other compression methods with the best compression ratio for test data compression. The decompression architecture for SDV codes is also presented for decoding the implementations of compressed bits. The proposed scheme shows that SDV codes are accessible to any of the variations in the input test data stream.

A Novel Variable Shifting Code for Test Compression of SoC

The test vector compression is a key technique to reduce IC test time and cost since the explosion of the test data of system on chip （SoC） in recent years. To reduce the bandwidth requirement between the automatic test equipment （ATE） and the CUT （circuit under test） effectively, a novel VSPTIDR （variable shifting prefix-tail identifier reverse） code for test stimulus data compression is designed. The encoding scheme is defined and analyzed in detail, and the decoder is presented and discussed. While the probability of 0 bits in the test set is greater than 0.92, the compression ratio from VSPTIDR code is better than the frequency-directed run-length （FDR） code, which can be proved by theoretical analysis and experiments. And the on-chip area overhead of VSPTIDR decoder is about 15.75 % less than the FDR decoder.

Effect of gravel on rock failure in glutenite reservoirs under different confining pressures

Due to the existence of gravel,glutenite is heterogeneous and different from fine-grained rocks such as sandstone and shale in structure.To fully understand the effect of gravel on failure mode in glutenite,we performed triaxial compression tests on different glutenites.The results indicate that failure modes of glutenite are complex due to the existence of gravel.Under different confining pressures,three failure modes were observed.The first failure mode,a tensile failure under uniaxial compression,produces multiple tortuous longitudinal cracks.In this failure mode,the interaction between gravels provides the lateral tensile stress for rock splitting.The second failure mode occurs under low and medium confining pressure and produces a crack band composed of micro-cracks around gravels.This failure mode conforms to the Mohr-Coulomb criterion and is generated by shear failure.In this failure mode,shear dilatancy and shear compaction may occur under different confining pressures to produce different crack band types.In the second failure mode,gravel-induced stress concentration produces masses of initial micro-cracks for shear cracking,and gravels deflect the fracture surfaces.As a result,the fracture is characterized by crack bands that are far broader than in fine-grained rocks.The third failure mode requires high confining pressure and produces disconnected cracks around gravels without apparent crack bands.In this failure mode,the gravel rarely breaks,indicating that the formation of these fractures is related to the deformation of the matrix.The third failure mode requires lower confining pressure in glutenite with weak cement and matrix support.Generally,unlike fine-grained rocks,the failure mode of glutenite is not only controlled by confining pressure but also by the gravel.The failure of glutenite is characterized by producing cracks around gravels.These cracks are produced by different mechanisms and distributed in different manners under different confining pressures to form different fracture patterns.Therefore,understanding the rock microstructure and formation stress state is essential in guiding glutenite reservoir development.

Effects of confining pressure and temperature on strength and deformation behavior of frozen saline silty clay

Buildings are always affected by frost heave and thaw settlement in cold regions,even where saline soil is present.This paper describes the triaxial testing results of frozen silty clay with high salt content and examines the in-fluence of confining pressure and temperature on its mechanical characteristics.Conventional triaxial compression tests were conducted under different confining pressures(0.5–7.0 MPa)and temperatures(-6℃,-8℃,-10℃,and-12℃).The test results show that when the confining pressure is less than 1 MPa,the frozen saline silty clay is dominated by brittle behavior with the X-shaped dilatancy failure mode.As the confining pressure increases,the sample gradually transitions from brittle to plastic behavior.The strength of frozen saline silty clay rises first and then decreases with increasing confining pressure.The improved Duncan-Chang hyperbolic model can describe the stress-strain relationship of frozen saline silty clay.And the parabolic strength criterion can be used to describe the strength evolution of frozen saline silty clay.The function relation of strength parameters with temperature is obtained by fitting,and the results of the parabolic strength criterion are in good agreement with the experimental results,especially when confining pressure is less than 5 MPa.Therefore,the study has important guiding significance for design and construction when considering high salinity soil as an engineering material in cold regions.

Hot deformation behavior of microstructural constituents in a duplex stainless steel during high-temperature straining

The hot deformation characteristics of 1.4462 duplex stainless steel （DSS） were analyzed by considering strain partitioning between austenite and ferrite constituents. The individual behavior of ferrite and austenite in microstructure was studied in an iso-stress condition. Hot compression tests were performed at temperatures of 800-1100~C and strain rates of 0.001-1 s-1. The flow stress was modeled by a hyperbolic sine constitutive equation, the corresponding constants and apparent activation energies were determined for the studied alloys. The constitutive equation and law of mixture were used to measure the contribution factor of each phase at any given strain. It is found that the contribution factor of ferrite exponentially declines as the Zener-HoUomon parameter （Z） increases. On the contrary, the austenite contribution polynomially increases with the increase of Z. At low Z values below 2.6. x 1015 （lnZ---35.5）, a negative contribution factor is determined for austenite that is attributed to dynamic recrystallization. At high Z values, the contribution factor of austenite is about two orders of magnitude greater than that of ferrite, and therefore, austenite can accommodate more strain. Microstructural characterization via electron back-scattered diffraction （EBSD） confirms the mechanical results and shows that austenite recrystallization is possible only at high temperature and low strain rate.

Tensile and compressive behavior of Ti-based bulk metallic glass composites

This article focuses on the tensile and compressive characteristics of a Ti-based bulk metallic glass composite （BMGC）. It is found that the yield stress, maximum strength, and fracture strain are 1380 MPa, 1516 MPa, and 4.3% for uniaxial tension, but 1580 MPa, 4010 MPa, and 29% for uniaxial compression, respectively. The composite displays a linear ＂work hardening＂ capacity under compression; however, the ＂work softening＂ behavior is observed in the true engineering stress-strain curve upon tensile loading. The fracture surfaces of specimens also exhibit dissimilar properties under the different loadings.

Compressive deformation behavior of an indirect-extruded Mg-8Sn-1Al-1Zn alloy

The medium and warm deformation behaviors of an indirect-extruded Mg-8Sn-IAI-IZn alloy were investigated by compression tests at temperatures between 298 and 523 K and strain rates of 0.001-10 s-1. It was found that the twinning-slip transition temperature was strain rate dependent, and all the true stress-true strain curves could be divided into two groups： concave and convex curves. Associated microstructural investigations indicated that the dynamic recrystallization （DRX） be- havior of the alloy varied with deformation conditions. At high strain rate and low temperature, dynamically recrystallized grains preferentially nucleated and developed in the twinned regions, indicating that twinning-induced DRX was dominant. While, at low strain rate, DRX developed extensively at grain boundaries and twins, and the process of twinning contributed to both oriented nucleation and selective growth. For the studied alloy, cracks mainly initiated from the shear band and twinning lamellar over the ranges of temperature and strain rate currently applied.

Validity of continuous-failure-state unloading triaxial tests as a means to estimate the residual strength of rocks

The residual strength of rocks and rock masses is an important parameter to be constrained for analysis and design purposes in many rock engineering applications.A residual strength envelope in principal stress space is typically developed using residual strength data obtained from compression tests on many different specimens of the same rock type.In this study,we examined the potential for use of the continuous-failure-state testing concept as a means to constrain the residual strength envelope using a limited number of specimens.Specifically,cylindrical specimens of three rock types(granodiorite,diabase,and Stanstead granite)were unloaded at the residual state such that a full residual strength envelope for each individual specimen was obtained.Using a residual strength model that introduces a single new strength parameter(the residual strength index,or RSI),the results of the continuous-failurestate unloading tests were compared to conventionally obtained residual strength envelopes.Overall,the continuous-failure-state residual strength data were found to be consistent with the conventional residual strength data.However,it was identified that the primary factor limiting an accurate characterization of the residual strength for a given rock type is not the amount of data for a given specimen,but the variety of specimens available to characterize the inherent variability of the rock unit of interest.Accordingly,the use of continuous-failure-state testing for estimation of the residual strength of a rock unit is only recommended when the number of specimens available for testing is very limited(i.e.<5).