Ion Dynamics in Concentrated Electrolyte Solutions:Relating Equilibrium Fluctuations of the Ions to Transport Properties in Battery Cells

In recent years,the interest in the development of highly concentrated electrolyte solutions for battery applications has increased enormously.Such electrolyte solutions are typically characterized by a low flammability,a high thermal and electrochemical stability and by the formation of a stable solid electrolyte interphase(SEI)in contact to electrode materials.However,the classification of concentrated electrolyte solutions in terms of the classical scheme"strong"or"weak"has been controversially discussed in the literature.In this paper,a comprehensive theoretical framework is presented for a more general classification,which is based on a comparison of charge transport and mass transport.By combining the Onsager transport formalism with linear response theory,center-of-mass fluctuations and collective translational dipole fluctuations of the ions in equilibrium are related to transport properties in a lithium-ion battery cell,namely mass transport,charge transport and Li^(+)transport under anion-blocking conditions.The relevance of the classification approach is substantiated by showing that i)it is straightforward to classify highly concentrated electrolytes and that ii)both fast charge transport and fast mass transport are indispensable for achieving fast Li^(+)transport under anion-blocking conditions.

Molecular dynamics study of primary radiation damage in TiVTa concentrated solid-solution alloy

The primary radiation damage in pure V and TiVTa concentrated solid-solution alloy(CSA)was studied using a molecular dynamics method.We have performed displacement cascade simulations to explore the generation and evolution behavior of irradiation defects.The results demonstrate that the defect accumulation and agglomeration in TiVTa CSA are significantly suppressed compared to pure V.The peak value of Frenkel pairs during cascade collisions in TiVTa CSA is much higher than that in pure V due to the lower formation energy of point defects.Meanwhile,the longer lifetime of the thermal spike relaxation and slow energy dissipation capability of TiVTa CSA can facilitate the recombination of point defects.The defect agglomeration rate in TiVTa CSA is much lower due to the lower binding energy of interstitial clusters and reduced interstitial diffusivity.Furthermore,the occurrence probability of dislocation loops in TiVTa CSA is lower than that in pure V.The reduction in primary radiation damage may enhance the radiation resistance of TiVTa CSA,and the improved radiation tolerance is primarily attributed to the relaxation stage and long-term defect evolution rather than the ballistic stage.These results can provide fundamental insights into irradiation-induced defects evolution in refractory CSAs.

Numerical Assessment of the Thermal Efficiency of a Concentrated Photovoltaic/Thermal (CPV/T) Hybrid System Using Air as Heat Transfer Fluid

In this paper, we propose a thermal model of a hybrid photovoltaic/thermal concentration system. Starting from the thermal balance of the model, the equation is solved and simulated with a MATLAB code, considering air as the cooling fluid. This enabled us to evaluate some of the parameters influencing the electrical and thermal performance of this device. The results showed that the temperature, thermal efficiency and electrical efficiency delivered depend on the air mass flow rate. The electrical and thermal efficiencies for different values of air mass flow are encouraging, and demonstrate the benefits of cooling photovoltaic cells. The results show that thermal efficiency decreases air flow rate greater than 0.7 kg/s, whatever the value of the light concentration used. The thermal efficiency of the solar cell increases as the light concentration increases, whatever the air flow rate used. For a concentration equal to 30 sun, the thermal efficiency is 0.16 with an air flow rate equal to 0.005 kg/s;the thermal efficiency increases to 0.19 with an air flow rate equal to 0.1 kg/s at the same concentration. An interesting and useful finding was that the proposed numerical model allows the determination of the electrical as well as thermal efficiency of the hybrid CPV/T with air flow as cooling fluid.

Effect of Gd on neutron absorption properties and electrochemical corrosion behavior of Zr-Gd alloy in boiling concentrated HNO3

A Zr-Gd alloy with neutron poisoning properties and resistance to boiling concentrated HNO3 corrosion was developed based on a corrosion-resistant Zr-702 alloy to meet the demand for neutron shielding in the closed-loop treatment of spent fuel and the nuclear chemical industry.In this study,1 wt.%,3 wt.%,5 wt.%,7 wt.%,and 9 wt.%Zr-Gd alloys were designed and fabricated with Zr-702 as the control element.The electrochemical behavior of the Zr-Gd alloys in boiling concentrated HNO3 was investigated,and the neutron shielding effect on plate thickness and Gd content was simulated.The experimental results demonstrate that the corrosion resistance of the alloy decreased slightly before~7-9 wt.%with increasing Gd content;this is the inflection point of its corrosion resistance.The alloy uniformly dissolved the Gd content that could not be dissolved in the Zr lattice,resulting in numerous micropores on the passivation coating,which deteriorated and accelerated the corrosion rate.The MCNP simulation demonstrated that when the Gd content was increased to 5 wt.%,a 2-mm-thick plate can shield 99.9%neutrons;an alloy with a Gd content≥7 wt.%required only a 1-mm-thick plate,thereby showing that the addition of Gd provides an excellent neutron poisoning effect.Thus,the corrosion resistance and neutron shielding performance of the Zr-Gd alloy can meet the harsh service requirements of the nuclear industry.

Moderately concentrated electrolyte enabling high-performance lithium metal batteries with a wide working temperature range

The electrolyte integrated with lithium metal anodes is subjected to the issues of interfacial compatibility and stability,which strongly influence the performances of high-energy lithium metal batteries.Here,we report a new electrolyte recipe viz.a moderately concentrated electrolyte comprising of 2.4 M lithium bis(fluorosulfonyl)imide(LiFSI)in a cosolvent mixture of fluorinated ethylene carbonate(FEC)and dimethyl carbonate(DMC)with relatively high ion conductivity.Owing to the preferential decomposition of LiFSI and FEC,an inorganic-rich interphase with abundant Li_(2)O and LiF nanocrystals is formed on lithium metal with improved robustness and ion transfer kinetics,enabling lithium plating/stripping with an extremely low overpotential of~8 mV and the average CE of 97%.When tested in Li||LiFePO_(4) cell,this electrolyte provides long-term cycling with a capacity retention of 98.3%after 1000 cycles at 1 C and an excellent rate performance of 20 C,as well as an areal capacity of 1.35 mA h cm^(-2)at the cathode areal loading of 9 mg cm^(-2).Moreover,the Li||LiFePO_(4) cell exhibits excellent wide-temperature performances(-40~60℃),including long-term cycling stability over 2600 cycles without visible capacity fading at 0℃,as well as extremely high average CEs of 99.6%and 99.8% over 400 cycles under-20℃ and 45℃.

Dynamics and genetic regulation of macronutrient concentrations during grain development in maize

Nitrogen(N), phosphorus(P), and potassium(K) are essential macronutrients that are crucial not only for maize growth and development, but also for crop yield and quality. The genetic basis of macronutrient dynamics and accumulation during grain filling in maize remains largely unknown. In this study, we evaluated grain N, P, and K concentrations in 206 recombinant inbred lines generated from a cross of DH1M and T877 at six time points after pollination. We then calculated conditional phenotypic values at different time intervals to explore the dynamic characteristics of the N, P, and K concentrations. Abundant phenotypic variations were observed in the concentrations and net changes of these nutrients. Unconditional quantitative trait locus(QTL) mapping revealed 41 non-redundant QTLs, including 17, 16, and 14 for the N, P, and K concentrations, respectively. Conditional QTL mapping uncovered 39 non-redundant QTLs related to net changes in the N, P, and K concentrations. By combining QTL, gene expression, co-expression analysis, and comparative genomic data, we identified 44, 36, and 44 candidate genes for the N, P, and K concentrations, respectively, including GRMZM2G371058 encoding a Doftype zinc finger DNA-binding family protein, which was associated with the N concentration, and GRMZM2G113967encoding a CBL-interacting protein kinase, which was related to the K concentration. The results deepen our understanding of the genetic factors controlling N, P, and K accumulation during maize grain development and provide valuable genes for the genetic improvement of nutrient concentrations in maize.

Comprehensive treatment of latex wastewater and resource utilization of concentrated liquid

Latex wastewater is a kind of refractory organic wastewater containing high concentrations of organics and ammonia nitrogen.In this work,the combined process of forward osmosis(FO)and reverse osmosis(RO)was designed to treat the latex wastewater in the whole process,achieving the water recovery rate of 99%and basically no waste discharge after the catalytic oxidation process.The turbidity of the latex wastewater was decreased to below 1 NTU by microfiltration pretreatment,and then using MgCl_2 worked as the draw solution for FO process to treat the latex wastewater.Different operation conditions including adding acid or scale inhibitor as the pretreatment methods were conducted to improve the treatment performance of the combined process.After the treatment of the whole process,the concentration of COD was less than 20 mg·L^(-1),the concentration of NH_3-N was less than 10 mg·L^(-1),and the concentration of TP was less than 0.5 mg·L^(-1)for the treated latex wastewater.The water quality met standards of industrial water reuse after the complete analysis of the treated latex wastewater,meanwhile,useful substances of L-Quebrachitol(L-Q)were successfully extracted from the concentrated solution.Therefore,the combined process of FO and RO could realize the efficient treatment and reuse of latex wastewater,which provided with some important guidance on the industrial application.

Static Analysis of Anisotropic Doubly-Curved Shell Subjected to Concentrated Loads Employing Higher Order Layer-Wise Theories

In the presentmanuscript,a Layer-Wise(LW)generalizedmodel is proposed for the linear static analysis of doublycurved shells constrained with general boundary conditions under the influence of concentrated and surface loads.The unknown field variable is modelled employing polynomials of various orders,each of them defined within each layer of the structure.As a particular case of the LW model,an Equivalent Single Layer(ESL)formulation is derived too.Different approaches are outlined for the assessment of external forces,as well as for non-conventional constraints.The doubly-curved shell is composed by superimposed generally anisotropic laminae,each of them characterized by an arbitrary orientation.The fundamental governing equations are derived starting from an orthogonal set of principal coordinates.Furthermore,generalized blending functions account for the distortion of the physical domain.The implementation of the fundamental governing equations is performed bymeans of the Generalized Differential Quadrature(GDQ)method,whereas the numerical integrations are computed employing theGeneralized IntegralQuadrature(GIQ)method.In the post-processing phase,an effective procedure is adopted for the reconstruction of stress and strain through-the-thickness distributions based on the exact fulfillment of three-dimensional equilibrium equations.A series of systematic investigations are performed in which the static response of structures with various curvatures and lamination schemes,calculated by the present methodology,have been successfully compared to those ones obtained fromrefined finite element three-dimensional simulations.Even though the present LW approach accounts for a two-dimensional assessment of the structural problem,it is capable of well predicting the three-dimensional response of structures with different characteristics,taking into account a reduced computational cost and pretending to be a valid alternative to widespread numerical implementations.

Concentrated ternary ether electrolyte allows for stable cycling of a lithium metal battery with commercial mass loading high-nickel NMC and thin anodes

A new concentrated ternary salt ether-based electrolyte enables stable cycling of lithium metal battery(LMB)cells with high-mass-loading(13.8 mg cm^(−2),2.5 mAh cm^(−2))NMC622(LiNi_(0.6)Co_(0.2)Mn_(0.2)O_(2))cathodes and 50μm Li anodes.Termed“CETHER-3,”this electrolyte is based on LiTFSI,LiDFOB,and LiBF4 with 5 vol%fluorinated ethylene carbonate in 1,2-dimethoxyethane.Commer-cial carbonate and state-of-the-art binary salt ether electrolytes were also tested as baselines.With CETHER-3,the electrochemical performance of the full-cell battery is among the most favorably reported in terms of high-voltage cycling stability.For example,LiNi_(x)Mn_(y)Co_(1-x-y)O_(2)(NMC)-Li metal cells retain 80%capacity at 430 cycles with a 4.4 V cut-off and 83%capacity at 100 cycles with a 4.5 V cut-off(charge at C/5,discharge at C/2).According to simulation by density functional theory and molecular dynamics,this favorable performance is an outcome of enhanced coordination between Li^(+)and the solvent/salt molecules.Combining advanced microscopy(high-resolution transmission electron microscopy,scanning electron microscopy)and surface science(X-ray photoelectron spectroscopy,time-of-fight secondary ion mass spectroscopy,Fourier-transform infrared spectroscopy,Raman spectroscopy),it is demonstrated that a thinner and more stable cathode electrolyte interphase(CEI)and solid electrolyte interphase(SEI)are formed.The CEI is rich in lithium sulfide(Li_(2)SO_(3)),while the SEI is rich in Li_(3)N and LiF.During cycling,the CEI/SEI suppresses both the deleterious transformation of the cathode R-3m layered near-surface structure into disordered rock salt and the growth of lithium metal dendrites.

Efficient desorption and reuse of collector from the flotation concentrate:A case study of scheelite

Flotation is the most common method to obtain concentrate through the selective adsorption of collectors on target minerals to make them hydrophobic and floatable.In the hydrometallurgy of concentrate,collectors adsorbed on concentrate can damage ion-exchange resin and increase the chemical oxygen demand(COD)value of wastewater.In this work,we proposed a new scheme,i.e.,desorbing the collectors from concentrate in ore dressing plant and reusing them in flotation flowsheet.Lead nitrate and benzohydroxamic acid(Pb-BHA)complex is a common collector in scheelite flotation.In this study,different physical(stirring or ultrasonic waves)and chemical(strong acid or alkali environment)methods for facilitating the desorption of Pb-BHA collector from scheelite concentrate were explored.Single-mineral desorption tests showed that under the condition of pulp pH 13 and ultrasonic treatment for 15 min,the highest desorption rates of Pb and BHA from the scheelite concentrate were 90.48%and 63.75%,respectively.Run-of-mine ore flotation tests revealed that the reuse of desorbed Pb and BHA reduced the collector dosage by 30%for BHA and 25%for Pb.The strong alkali environment broke the chemical bonds between Pb and BHA.The cavitation effect of ultrasonic waves effectively reduced the interaction intensity between Pb-BHA collector and scheelite surfaces.This method combining ultrasonic waves and strong alkali environment can effectively desorb the collectors from concentrate and provide“clean”scheelite concentrate for metallurgic plants;the reuse of desorbed collector in flotation flowsheet can reduce reagent cost for ore dressing plants.

Different concentrations of hyaluronic acid eye drops for dry eye syndrome: a systematic review and Meta-analysis

AIM:To compare high or low concentration of hyaluronic acid eye drops(HY)for dry eye syndromes(DES).METHODS:Randomized controlled trials(RCTs)comparing various concentrations of HY were searched in PubMed,Embase,Web of Science,Cochrane,SinoMed,CNKI,Wanfang Database,CQVIP,and Chinese journals databases between inception and July 2023.Pooled standardized mean differences(SMD)or weighted mean difference(WMD)with 95%confidence intervals(CI)from RCTs evaluating Schirmer’s I test(SIT),corneal fluorescein staining score(CFS),tear breakup time(TBUT),DES score(DESS),and Ocular Surface Disease Index(OSDI)were calculated.Sensitivity analysis,Egger’s test and Meta-regression analysis were performed for all indicators.RESULTS:We conducted a Meta-analysis of 10 RCTs that met the inclusion criteria,involving 1796 cases.High-concentrations group significantly improved the outcome of CFS according to random effects modelling(SMD,-3.37;95%CI,-5.25 to-1.48;P=0.0005).The rest of the results were not statistically significant,including indicators such as SIT,TBUT,DESS and OSDI.CONCLUSION:For dry eyes with positive corneal staining,a high concentration of HY is recommended,whereas in other cases,a high concentration of HY does not offer a more pronounced advantage over a low concentration of HY in the treatment of dry eyes.

Achievable hole concentration at room temperature as a function of Mg concentration for MOCVD-grown p-GaN after sufficient annealing

Relationship between the hole concentration at room temperature and the Mg doping concentration in p-GaN grown by MOCVD after sufficient annealing was studied in this paper.Different annealing conditions were applied to obtain sufficient activation for p-GaN samples with different Mg doping ranges.Hole concentration,resistivity and mobility were characterized by room-temperature Hall measurements.The Mg doping concentration and the residual impurities such as H,C,O and Si were measured by secondary ion mass spectroscopy,confirming negligible compensations by the impurities.The hole concentration,resistivity and mobility data are presented as a function of Mg concentration,and are compared with literature data.The appropriate curve relating the Mg doping concentration to the hole concentration is derived using a charge neutrality equation and the ionized-acceptor-density[N-(A)^(-)](cm^(−3))dependent ionization energy of Mg acceptor was determined asE_(A)^(Mg)=184−2.66×10^(−5)×[N_(A)^(-)]1/3 meV.

Effects of Different Concentrations of Sulfate Ions on Carbonate Crude Oil Desorption:Experimental Analysis and Molecular Simulation

Low salinity water containing sulfate ions can significantly alter the surface wettability of carbonate rocks.Nevertheless,the impact of sulfate concentration on the desorption of oil film on the surface of carbonate rock is still unknown.This study examines the variations in the wettability of the surface of carbonate rocks in solutions containing varying amounts of sodium sulfate and pure water.The problem is addressed in the framework of molecular dynamics simulation(Material Studio software)and experiments.The experiment’s findings demonstrate that sodium sulfate can increase the rate at which oil moisture is turned into water moisture.The final contact angle is smaller than that of pure water.The results of the simulations show that many water molecules travel down the water channel under the influence of several powerful forces,including the electrostatic force,the van der Waals force and hydrogen bond,crowding out the oil molecules on the calcite’s surface and causing the oil film to separate.The relative concentration curve of water and oil molecules indicates that the separation rate of the oil film on the surface of calcite increases with the number of sulfate ions.

Study on concentration distribution and detonation characteristics for non-axisymmetric fuel dispersal

The study of non-axisymmetric fuel dispersal and detonation can provide reference for the prevention of industrial cloud explosion accidents and the design of fuel air explosive(FAE).The concentration and detonation fields of 85 kg cylindrical and fan-shaped fuel are investigated by experiments and numerical simulations.A dynamic model of the whole process for fuel dispersal and detonation is built.The concentration distribution of fuel is used as the initial condition to calculate the detonation stage,thus solving the initial value problem of detonation field.The phase and component changes of fuel cloud at different locations are compared.The fuel cloud is divided into directions of 0°,90°,135°and 180°.The results show that the maximum cloud radius is 20.94 m in 135°and the minimum is 12.04 m in 0°.The diameter of the detonation fireball is 53.6 m,and the peak temperature is 3455 K.The highest peak overpressure is 3.44 MPa in 0°and the lowest is 2.97 MPa in 135°.The proportion of liquid phase in 0°is22.90%,and the fuel loss is 11.8% and 9% higher than that in 135°and cylindrical charge,respectively.The stable propagation distance of blast wave in 135°is 42.50% longer than 0°and 28.37% longer than cylindrical charge.

Effects of Serum Concentration, Synchronization Time and Confluence on the Cell-Cycle Synchronization Efficiency of Goat Fibroblasts

This study aims to evaluate the effect of serum concentration, synchronization time, and confluence degree on the synchronisation efficiency of goat fibroblast cycle. The results indicated that there was no difference in the percentage of nucleated fibroblasts in the G0/G1 stage between serum concentrations of 0.3% and 0.4% (83.89% and 82.69%, respectively, P > 0.05) as well as between serum concentrations of 0.2% and 0.5% (76.95% and 75.46%, respectively, P > 0.05). The percentage of nucleated fibroblasts in the G0/G1 stage was highest at the concentration of 0.3% and lowest in the control group (83.89% vs. 62.67%, P 0.05). The beneficial effect of high confluence was confirmed by the large percentage of nucleated fibroblasts at the G0/G1 stage. The 60% confluency was significantly lower than the 80% and 100% confluency (73.44%, 86.63%, and 87.17%, respectively, P < 0.05). The results indicate that the goat fibroblast cycle synchronization is the most effective at the serum concentration of 0.3%, 72 hours of synchronization and 100% confluency.

Effects of different concentrations of nicotinamide on hematopoietic stem cells cultured in vitro

BACKGROUND In vitro expansion to increase numbers of hematopoietic stem cells(HSCs)in cord blood could improve clinical efficacy of this vital resource.Nicotinamide(NAM)can promote HSC expansion ex vivo,but its effect on hematopoietic stem and progenitor cells(HSPCs,CD34^(+)CD38)and functional subtypes of HSCs-shortterm repopulating HSCs(ST-HSCs,CD34^(+)CD38CD45RACD49f^(+))and long-term repopulating HSCs(LT-HSCs,CD34^(+)CD38CD45RACD49f^(+)CD90^(+))is not yet known.As a sirtuin 1(SIRT1)inhibitor,NAM participates in regulating cell adhesion,polarity,migration,proliferation,and differentiation.However,SIRT1 exhibits dual effects by promoting or inhibiting differentiation in different tissues or cells.We propose that the concentration of NAM may influence proliferation,differentiation,and SIRT1 signaling of HSCs.AIM To evaluate the effects and underlying mechanisms of action of different concentrations of NAM on HSC proliferation and differentiation.METHODS CD34^(+)cells were purified from umbilical cord blood using MacsCD34 beads,and cultured for 10-12 d in a serum-free medium supplemented with cytokines,with different concentrations of NAM added according to experimental requirements.Flow cytometry was used to detect phenotype,cell cycle distribution,and apoptosis of the cultured cells.Real-time polymerase chain reaction was used to detect the transcription levels of target genes encoding stemness-related factors,che mokines,components of hypoxia pathways,and antioxidant enzymes.Dichloro-dihydro-fluorescein diacetate probes were used to evaluate intracellular production of reactive oxygen species(ROS).Determination of the effect of different culture conditions on the balance of cytokine by cytometric bead array.RESULTS Compared with the control group,the proportion and expansion folds of HSPCs(CD34^(+)CD38)incubated with 5 mmol/L or 10 mmol/L NAM were significantly increased(all P<0.05).The ST-HSCs ratio and fold expansion of the 5 mmol/L NAM group were significantly higher than those of the control and 10 mmol/L NAM groups(all P<0.001),whereas the LT-HSCs ratio and fold expansion of the 10 mmol/L NAM group were significantly higher than those of the other two groups(all P<0.05).When the NAM concentration was>10 mmol/L,cell viability significantly decreased.In addition,compared with the 5 mmol/L NAM group,the proportion of apoptotic cells in the 10 mmol/L NAM group increased and the proportion of cells in S and G2 phase decreased.Compared with the 5 mmol/L NAM group,the HSCs incubated with 10 mmol/L NAM exhibited significantly inhibited SIRT1 expression,increased intracellular ROS content,and downregulated expression of genes encoding antioxidant enzymes(superoxide dismutase 1,peroxiredoxin 1).CONCLUSION Low concentrations(5 mmol/L)of NAM can better regulate the balance between proliferation and differentiation,thereby promoting expansion of HSCs.These findings allow adjustment of NAM concentrations according to expansion needs.

Rheological properties and concentration evolution of thickened tailings under the coupling effect of compression and shear

Cemented paste backfill(CPB)is a key technology for green mining in metal mines,in which tailings thickening comprises the primary link of CPB technology.However,difficult flocculation and substandard concentrations of thickened tailings often occur.The rheological properties and concentration evolution in the thickened tailings remain unclear.Moreover,traditional indoor thickening experiments have yet to quantitatively characterize their rheological properties.An experiment of flocculation condition optimization based on the Box-Behnken design(BBD)was performed in the study,and the two response values were investigated:concentration and the mean weighted chord length(MWCL)of flocs.Thus,optimal flocculation conditions were obtained.In addition,the rheological properties and concentration evolution of different flocculant dosages and ultrafine tailing contents under shear,compression,and compression-shear coupling experimental conditions were tested and compared.The results show that the shear yield stress under compression and compression-shear coupling increases with the growth of compressive yield stress,while the shear yield stress increases slightly under shear.The order of shear yield stress from low to high under different thickening conditions is shear,compression,and compression-shear coupling.Under compression and compression-shear coupling,the concentration first rapidly increases with the growth of compressive yield stress and then slowly increases,while concentration increases slightly under shear.The order of concentration from low to high under different thickening conditions is shear,compression,and compression-shear coupling.Finally,the evolution mechanism of the flocs and drainage channels during the thickening of the thickened tailings under different experimental conditions was revealed.

A Facile Li_(2)TiO_(3) Surface Modification to Improve the Structure Stability and Electrochemical Performance of Full Concentration Gradient Li-Rich Oxides

Full concentration gradient lithium-rich layered oxides are catching lots of interest as the next generation cathode for lithium-ion batteries due to their high discharge voltage,reduced voltage decay and enhanced rate performance,whereas the high lithium residues on its surface impairs the structure stability and long-term cycle performance.Herein,a facile multifunctional surface modification method is implemented to eliminate surface lithium residues of full concentration gradient lithium-rich layered oxides by a wet chemistry reaction with tetrabutyl titanate and the post-annealing process.It realizes not only a stable Li_(2)TiO_(3)coating layer with 3D diffusion channels for fast Li^(+)ions transfer,but also dopes partial Ti^(4+)ions into the sub-surface region of full concentration gradient lithium-rich layered oxides to further strengthen its crystal structure.Consequently,the modified full concentration gradient lithium-rich layered oxides exhibit improved structure stability,elevated thermal stability with decomposition temperature from 289.57℃to 321.72℃,and enhanced cycle performance(205.1 mAh g^(-1)after 150 cycles)with slowed voltage drop(1.67 mV per cycle).This work proposes a facile and integrated modification method to enhance the comprehensive performance of full concentration gradient lithium-rich layered oxides,which can facilitate its practical application for developing higher energy density lithium-ion batteries.

Global CO_(2)concentration change induced by“trigger-connectors”model,especially since about 24 Ma?A preliminary hypothesis

Background,aim,and scope The tectonic uplift of the Cenozoic Tibetan Plateau has produced a chain effect,which is an excellent location for Earth system science research,and its uplift process,mechanism and environmental effects are the hot spot and frontier of the current research.The“Tibetan Plateau uplift-weathering-CO_(2)concentration-global climate change”model was put forward by Raymo and Ruddiman to interpret the Late Cenozoic climate change.However,there are still some questions suspended,such as does the weathering of the Tibetan Plateau have the ability to control the global climate?How to explain the modern-like global CO_(2)concentration starting at about 24 Ma?Here,a short space was taken to present a brainstorm about the above questions on account of existing geological pieces of evidence.Materials and methods In this paper,we integrate the formation and evolution of the Yangtze River and Pearl River,the origin and development of the Asian inland aridification-monsoon system,the Cenozoic tectonic uplift process of the Tibetan Plateau,and the westerly winds to discuss and analyze the relationship between the Cenozoic CO_(2)concentration changes and the uplift of the Tibetan Plateau and why the CO_(2)concentration similar to the present was formed at about 24 Ma.Results Similar correspondence of the surface uplift history of Xizang,other global mountains,and the declining CO_(2)concentration could support the theory Tibetan Plateau weathering inf luences CO_(2)concentration.Starting from 24 Ma,the most important character was the uplift and erosion of Xizang and Himalaya,collaborating with Ocean Iron Fertilization(OIF)together as an entity to control the atmospheric CO_(2)concentration because the great Asian rivers,Asian monsoons,and westerlies connected Xizang and surrounded seas together through materials transportation.Discussion Paleogeographic reconstructions from 40 Ma to 20 Ma illustrate that the main topographic change occurred in the Andes,Cordillera orogenic belt,and Xizang.We comprise a comprehensive set of evidence from independent data,which correspond temporally with the tipping point(about 24 Ma)of the atmospheric CO_(2)and we noticed that modern-like Asia monsoon,inland aridity,Asian great rivers,and climate zone formed at about 24 Ma and also there are tectonic activities for the Andes and Rockies.We raised the possibility that the modern-like atmospheric CO_(2)concentration at about 24 Ma was caused by the above geological factors.Here the rivers,monsoon,and westerlies are termed as“connectors”.In addition,these Asian rivers originated from Xizang,the monsoon,and inner Asian aridification are strongly a function of the uplift and growth of Xizang,thus,Xizang here is named as“trigger”.The distinct character of“trigger-connectors”model is that this not only takes the monsoon,westerlies,and the global great rivers into consideration but also expands the range which inf luences atmospheric CO_(2)concentration,from local points to a vast area since about 24 Ma,such as from Tibetan Plateau to Asia,including surrounded seas,after about 24 Ma.However,because the opening of the Late Oligocene-Early Miocene Antarctic periphery straits is highly coincident with the onset of modern-like global atmospheric CO_(2)concentration,we are forced to consider that they also had a significant impact on the reduction of atmospheric CO_(2)concentrations at this time.Conclusions“Trigger-connectors”was put forward to explain the Cenozoic CO_(2)variation,especially modern-like global CO_(2)concentration since about 24 Ma.Recommendations and perspectives Here we use the“trigger-connectors”model to explain the formation of modern-like CO_(2)concentrations starting at about 24 Ma,but there are still some problems.The most important premise for the“trigger-connectors”model is the constructed Cenozoic CO_(2)concentration record is reliable,which is the foundation of our hypothesis.In the future,potential improvements should focus on topographic reconstructions of Xizang and the global mountains.Here we have concentrated on Xizang in the considered timeslices but still,pay less attention to other global orogenic belts.Collaborations with geologist experts in those regions could provide valuable feedback to evaluate their potential role of them in CO_(2)evolution.What is more,considerable progress may be achieved with the addition and consideration of more and new geological data.

Effect of low concentration electrolytes on the formation and corrosion resistance of PEO coatings on AM50 magnesium alloy

In this paper,the formation process,morphology,and electrochemical performance of PEO coatings on AM50 magnesium alloy prepared in low concentration phosphate,aluminate,and phosphate-aluminate electrolytes were systematically studied.The results show that the coatings prepared from the phosphate electrolytes have a higher thickness and better corrosion resistance properties compared to the other electrolytes.The coatings prepared from low concentration phosphate-aluminate mixed electrolytes have slightly thinner thickness,a similar coating structure and an order of magnitude lower value of electrochemical impedance compared with phosphate electrolyte coatings.The Coatings prepared from low concentration aluminate electrolytes have the lowest thickness and the worst corrosion resistance properties which gets close to corrosion behavior of the bare AM50 under the same test conditions.Considering application,coatings prepared from single low concentration phosphate electrolytes and low concentration phosphate-aluminate electrolytes have greater potential than single low concentration aluminate coatings.However,reducing the electrolyte concentrations of coating forming ions too much has negative influence on the coating growth rate.