An adaptive response compensation technique has been proposed to compensate for the response lag of the constant-current hot-wire anemometer (CCA) by taking advantage of digital signal processing technology. First, we...An adaptive response compensation technique has been proposed to compensate for the response lag of the constant-current hot-wire anemometer (CCA) by taking advantage of digital signal processing technology. First, we have developed a simple response compensation scheme based on a precise theoretical expression for the frequency response of the CCA (Kaifuku et al. 2010, 2011), and verified its effectiveness experimentally for hot-wires of 5 μm, 10 μm and 20 μm in diameter. Then, another novel technique based on a two-sensor probe technique—originally developed for the response compensation of fine-wire thermocouples (Tagawa and Ohta 1997;Tagawa et al. 1998)—has been proposed for estimating thermal time-constants of hot-wires to realize the in-situ response compensation of the CCA. To demonstrate the usefulness of the CCA, we have applied the response compensation schemes to multipoint velocity measure- ment of a turbulent wake flow formed behind a circular cylinder by using a CCA probe consisting of 16 hot-wires, which were driven simultaneously by a very simple constant-current circuit. As a result, the proposed response compensation techniques for the CCA work quite successfully and are capable of improving the response speed of the CCA to obtain reliable measurements comparable to those by the commercially-available constant-temperature hot-wire anemometer (CTA).展开更多
The derivative of charge and discharge curves (d t /d E vs E plot) can be used to describe the charge and discharge process more exactly. The d t /d E ? 獷 plots of nickel hydroxide electrode at different charge/disch...The derivative of charge and discharge curves (d t /d E vs E plot) can be used to describe the charge and discharge process more exactly. The d t /d E ? 獷 plots of nickel hydroxide electrode at different charge/discharge rates and intermittent discharge experiment are discussed. Though the d t /d E ? 獷 plot is affected by many factors, it clearly has intrinsic relation with the nature of active material such as conductivity and thermodynamic potential of active material, which changes with the state of charge. The d t /d E—E plot can also be applied to other electrochemical active materials, especially to those having several phases during charge or discharge.展开更多
This paper proposes a design and control approach to parallel resonant converter(PRC) based battery chargers.The proposed approach is particularly suitable for the constant-current constant-voltage(CC-CV)charging meth...This paper proposes a design and control approach to parallel resonant converter(PRC) based battery chargers.The proposed approach is particularly suitable for the constant-current constant-voltage(CC-CV)charging method, which is the most commonly utilized one.Since the PRC is operated at two different frequencies for each CC and CV charging modes, this approach eliminates the need for complicated control techniques such as the frequency-control and phase-shift-control.The proposed method not only simplifies the design and implementation processes of the converter unit but also simplifies the design of output filter configuration and decreases the number of the required components for the control of the charger.The proposed method is confirmed by two experimental setups.The results show that the designed charger circuit ensured a very stable constant current in CC charging phase, where the charging current is fixed to 1.75 A.Although a voltage increase in CV phase is observed, the charger circuit is able to decrease the charging current to 0.5 A in CV phase, as depicted in battery data-sheet.The efficiency of the charger is figured out to be in the range of 86%-93% in the first setup, while it is found to be in the range of 78%-88% in the second setup,where a high frequency transformer is employed.展开更多
A 5.0-V 2.0-A flyback power supply controller providing constant-voltage （CV） and constant-current （CC） output regulation without the use of an optical coupler is presented. Dual-close-loop control is proposed her...A 5.0-V 2.0-A flyback power supply controller providing constant-voltage （CV） and constant-current （CC） output regulation without the use of an optical coupler is presented. Dual-close-loop control is proposed here due to its better regulation performance of tolerance over process and temperature compared with open loop control used in common. At the same time, the two modes, CC and CV, could switch to each other automatically and smoothly according to the output voltage level not sacrificing the regulation accuracy at the switching phase, which overcomes the drawback of the digital control scheme depending on a hysteresis comparator to change the mode. On-chip compensation using active capacitor multiplier technique is applied to stabilize the voltage loop, eliminate an additional package pin, and save on the die area. The system consumes as little as 100 mW at no-load condition without degrading the transient response performance by utilizing the adaptive switching frequency control mode. The proposed controller has been implemented in a commercial 0.35μm 40-V BCD process, and the active chip area is 1.5×1.0 mm^2. The total error of the output voltage due to line and load variations is less than 4-1.7%.展开更多
SiC MOSFET是一种高性能的电力电子器件,其开通/关断过程中积累/释放的栅电荷Q_(g)对MOSFET的开关速度、功率损耗等参数有重要影响。通常采用在栅极设置恒流源驱动,对时间进行积分的方法来测量Q_(g)。为了降低驱动复杂度,提高测试结果...SiC MOSFET是一种高性能的电力电子器件,其开通/关断过程中积累/释放的栅电荷Q_(g)对MOSFET的开关速度、功率损耗等参数有重要影响。通常采用在栅极设置恒流源驱动,对时间进行积分的方法来测量Q_(g)。为了降低驱动复杂度,提高测试结果精度和可视性,基于双脉冲测试平台的感性负载回路,改用耗尽型MOSFET限制栅极电流实现恒流充电,对SiC MOSFET进行测试。同时利用反馈电阻将较小的栅极电流信号转换为较大的电压信号。实验结果表明:在误差允许范围(±5%)内该测试方案能较为准确地测得SiC MOSFET的Q_(g),测试结果符合器件规格书曲线。展开更多
文摘An adaptive response compensation technique has been proposed to compensate for the response lag of the constant-current hot-wire anemometer (CCA) by taking advantage of digital signal processing technology. First, we have developed a simple response compensation scheme based on a precise theoretical expression for the frequency response of the CCA (Kaifuku et al. 2010, 2011), and verified its effectiveness experimentally for hot-wires of 5 μm, 10 μm and 20 μm in diameter. Then, another novel technique based on a two-sensor probe technique—originally developed for the response compensation of fine-wire thermocouples (Tagawa and Ohta 1997;Tagawa et al. 1998)—has been proposed for estimating thermal time-constants of hot-wires to realize the in-situ response compensation of the CCA. To demonstrate the usefulness of the CCA, we have applied the response compensation schemes to multipoint velocity measure- ment of a turbulent wake flow formed behind a circular cylinder by using a CCA probe consisting of 16 hot-wires, which were driven simultaneously by a very simple constant-current circuit. As a result, the proposed response compensation techniques for the CCA work quite successfully and are capable of improving the response speed of the CCA to obtain reliable measurements comparable to those by the commercially-available constant-temperature hot-wire anemometer (CTA).
文摘The derivative of charge and discharge curves (d t /d E vs E plot) can be used to describe the charge and discharge process more exactly. The d t /d E ? 獷 plots of nickel hydroxide electrode at different charge/discharge rates and intermittent discharge experiment are discussed. Though the d t /d E ? 獷 plot is affected by many factors, it clearly has intrinsic relation with the nature of active material such as conductivity and thermodynamic potential of active material, which changes with the state of charge. The d t /d E—E plot can also be applied to other electrochemical active materials, especially to those having several phases during charge or discharge.
文摘This paper proposes a design and control approach to parallel resonant converter(PRC) based battery chargers.The proposed approach is particularly suitable for the constant-current constant-voltage(CC-CV)charging method, which is the most commonly utilized one.Since the PRC is operated at two different frequencies for each CC and CV charging modes, this approach eliminates the need for complicated control techniques such as the frequency-control and phase-shift-control.The proposed method not only simplifies the design and implementation processes of the converter unit but also simplifies the design of output filter configuration and decreases the number of the required components for the control of the charger.The proposed method is confirmed by two experimental setups.The results show that the designed charger circuit ensured a very stable constant current in CC charging phase, where the charging current is fixed to 1.75 A.Although a voltage increase in CV phase is observed, the charger circuit is able to decrease the charging current to 0.5 A in CV phase, as depicted in battery data-sheet.The efficiency of the charger is figured out to be in the range of 86%-93% in the first setup, while it is found to be in the range of 78%-88% in the second setup,where a high frequency transformer is employed.
文摘A 5.0-V 2.0-A flyback power supply controller providing constant-voltage （CV） and constant-current （CC） output regulation without the use of an optical coupler is presented. Dual-close-loop control is proposed here due to its better regulation performance of tolerance over process and temperature compared with open loop control used in common. At the same time, the two modes, CC and CV, could switch to each other automatically and smoothly according to the output voltage level not sacrificing the regulation accuracy at the switching phase, which overcomes the drawback of the digital control scheme depending on a hysteresis comparator to change the mode. On-chip compensation using active capacitor multiplier technique is applied to stabilize the voltage loop, eliminate an additional package pin, and save on the die area. The system consumes as little as 100 mW at no-load condition without degrading the transient response performance by utilizing the adaptive switching frequency control mode. The proposed controller has been implemented in a commercial 0.35μm 40-V BCD process, and the active chip area is 1.5×1.0 mm^2. The total error of the output voltage due to line and load variations is less than 4-1.7%.
