Objective:This study investigated the effect of proximal contact strength on the three-dimensional displacements of cantilever fixed partial denture(CFPD) under vertically concentrated loading with digital laser speck...Objective:This study investigated the effect of proximal contact strength on the three-dimensional displacements of cantilever fixed partial denture(CFPD) under vertically concentrated loading with digital laser speckle(DLS) technique.Methods:Fresh mandible of beagle dog was used to establish the implant-supported CFPD for specimen.DLS technique was employed for measuring the three-dimensional displacement of the prosthesis under vertically concentrated loading ranging from 200 to 3 000 g.The effect of the contact tightness on the displacement of CFPD was investigated by means of changing the contact tightness.Results:When an axial concentrated loading was exerted on the pontic of the implant-supported CFPD,the displacement of the CFPD was the greatest.The displacement of the prosthesis decreased with the increase of contact strength.When the contact strength was 0,0.95,and 3.25 N,the displacement of the buccolingual direction was smaller than that of the mesiodistal direction but greater than that of the occlusogingival direction.When the force on the contact area was 6.50 N,the mesiodistal displacement of the prosthesis was the biggest while the buccolingual displacement was the smallest.Conclusions:The implant supported CFPD is an effective therapy for fully or partially edentulous patients.The restoration of the contact area and the selection of the appropriate contact strength can reduce the displacement of the CFPD,and get a better stress distribution.The most appropriate force value is 3.25 N in this study.展开更多
The model for computing frictional coefficient between two teeth faces at the state of mixed elastohydrodynamic lubrication is established. And then more than 80 sets of numerical calculations and six sets of disc fat...The model for computing frictional coefficient between two teeth faces at the state of mixed elastohydrodynamic lubrication is established. And then more than 80 sets of numerical calculations and six sets of disc fatigue tests are completed. The results show that when the film thickness ratio λ 〈1.6, frictional coefficient μ is drastically decreased as λ. rises; Thereafter it decreases smoothly until λ=4.5. When λ〉4.5, however, it goes up again with λ, which indicates that the excessive film thickness ratio will deteriorate gearing contact fatigue strength. At the end, the formulae for determining the frictional coefficients are formed.展开更多
To downsize and lighten automatic transmission components, the gears installed must be strengthened in terms of pitting endurance and/or wear resistance. The most important metallurgical factor affecting fractures is ...To downsize and lighten automatic transmission components, the gears installed must be strengthened in terms of pitting endurance and/or wear resistance. The most important metallurgical factor affecting fractures is well known to be resistance to softening when steel is tempered at approximately 573 K. Carbonitriding with a high amount of nitrogen is a very effective production technique because nitrogen increases the resistance during tempering. However, structural anomalies begin to appear in the surface layer when the nitrogen content exceeds 0.6 mass% in the chromium steel generally used. To address this, we have developed new high-strength chromium steel with an optimized chemical composition that effectively inhibits anomalies even when Carbonitriding with a nitrogen content of more than 0.6 mass%. We performed a drivetrain durability test on an automatic transmission component designed to have excellent contact fatigue strength and a tooth root bending impact and fatigue strength. We found that the developed steel that was carbonitrided with a content of about 0.9 mass%, and then shot peened hard, has a pitting life of roughly 4.5 times that of conventionally manufactured steel.展开更多
As the thickness of silicon solar wafer and solar cells becomes thinner, the cells are subjected to high stress due to the thermal coefficient mismatch induced by metallization process. Handling and bowing problems as...As the thickness of silicon solar wafer and solar cells becomes thinner, the cells are subjected to high stress due to the thermal coefficient mismatch induced by metallization process. Handling and bowing problems associated with thinner wafers become increasingly important, as these can lead to cells cracking and thus to high yield losses. The goal of this work to provide experimental understanding of Al rear side microstructure development and mechanical properties as well as correlate the obtained results with fracture behaviour of the cell. It is shown that the aluminium back contact has a complex microstructure, consisting of five main components: 1) the back surface field layer;2) a eutectic layer;3) spherical (3 - 5 μm) hypereutectic Al-Si particles surrounded by a thin aluminium oxide layer (200 nm);4) a bis- muth-silicate glass matrix;and 5) pores (14 vol%). It was concluded that the eutectic layer thickness and waviness depends on Al particle size, amount of Al paste and textured surface roughness of silicon wafers. The Young’s modulus of the Al-Si particles is estimated by nano-indentation and the overall Young’s modulus is estimated on the basis of bowing measurements and found to be ~43 GPa. It was found, that there is a relation between aluminium paste composition, eutectic layer thickness, mechanical strength and bowing of solar cells. Three main parameters were found to affect the mechanical strength of mc-silicon solar cells with an aluminium contact layer, namely the eutectic layer thickness and uniformity, the Al layer thickness (which results from the Al particle size and its distribution), and the amount of porosity and the bismuth glass fraction.展开更多
CuCr25W1Ni2 alloy was prepared by means of vacuum induction melting (VIM). A series of Cu/Cr alloys with different compositions (mass fraction, 25%～75%) and Cr grain sizes (up to 150 μm) were investigated for their ...CuCr25W1Ni2 alloy was prepared by means of vacuum induction melting (VIM). A series of Cu/Cr alloys with different compositions (mass fraction, 25%～75%) and Cr grain sizes (up to 150 μm) were investigated for their differences in physical properties and breakdown voltage. The influence of alloy elements and microstructure on the performance of CuCr25W1Ni2 alloy was also discussed. Experimental results show that the chromium phase is strengthened and its size is minimized by the addition of tungsten powder. After electrical breakdown, very fine tungsten particles in the melt layer form the external nuclei in the solidification process. The microstructure of surface melt layer of CuCr25W1Ni2 alloy is much flatter. It can notably improve the dielectric strength. On the other hand, the nickel can enhance the mutual solubility of copper and chromium, and the whole alloy is strengthened. [展开更多
文摘Objective:This study investigated the effect of proximal contact strength on the three-dimensional displacements of cantilever fixed partial denture(CFPD) under vertically concentrated loading with digital laser speckle(DLS) technique.Methods:Fresh mandible of beagle dog was used to establish the implant-supported CFPD for specimen.DLS technique was employed for measuring the three-dimensional displacement of the prosthesis under vertically concentrated loading ranging from 200 to 3 000 g.The effect of the contact tightness on the displacement of CFPD was investigated by means of changing the contact tightness.Results:When an axial concentrated loading was exerted on the pontic of the implant-supported CFPD,the displacement of the CFPD was the greatest.The displacement of the prosthesis decreased with the increase of contact strength.When the contact strength was 0,0.95,and 3.25 N,the displacement of the buccolingual direction was smaller than that of the mesiodistal direction but greater than that of the occlusogingival direction.When the force on the contact area was 6.50 N,the mesiodistal displacement of the prosthesis was the biggest while the buccolingual displacement was the smallest.Conclusions:The implant supported CFPD is an effective therapy for fully or partially edentulous patients.The restoration of the contact area and the selection of the appropriate contact strength can reduce the displacement of the CFPD,and get a better stress distribution.The most appropriate force value is 3.25 N in this study.
基金This project is supported by Provincial Natural Science Foundation of Shanxi, China (No. 20041057)Scholarship Council of Shanxi, China (No. 2005-22)
文摘The model for computing frictional coefficient between two teeth faces at the state of mixed elastohydrodynamic lubrication is established. And then more than 80 sets of numerical calculations and six sets of disc fatigue tests are completed. The results show that when the film thickness ratio λ 〈1.6, frictional coefficient μ is drastically decreased as λ. rises; Thereafter it decreases smoothly until λ=4.5. When λ〉4.5, however, it goes up again with λ, which indicates that the excessive film thickness ratio will deteriorate gearing contact fatigue strength. At the end, the formulae for determining the frictional coefficients are formed.
文摘To downsize and lighten automatic transmission components, the gears installed must be strengthened in terms of pitting endurance and/or wear resistance. The most important metallurgical factor affecting fractures is well known to be resistance to softening when steel is tempered at approximately 573 K. Carbonitriding with a high amount of nitrogen is a very effective production technique because nitrogen increases the resistance during tempering. However, structural anomalies begin to appear in the surface layer when the nitrogen content exceeds 0.6 mass% in the chromium steel generally used. To address this, we have developed new high-strength chromium steel with an optimized chemical composition that effectively inhibits anomalies even when Carbonitriding with a nitrogen content of more than 0.6 mass%. We performed a drivetrain durability test on an automatic transmission component designed to have excellent contact fatigue strength and a tooth root bending impact and fatigue strength. We found that the developed steel that was carbonitrided with a content of about 0.9 mass%, and then shot peened hard, has a pitting life of roughly 4.5 times that of conventionally manufactured steel.
文摘As the thickness of silicon solar wafer and solar cells becomes thinner, the cells are subjected to high stress due to the thermal coefficient mismatch induced by metallization process. Handling and bowing problems associated with thinner wafers become increasingly important, as these can lead to cells cracking and thus to high yield losses. The goal of this work to provide experimental understanding of Al rear side microstructure development and mechanical properties as well as correlate the obtained results with fracture behaviour of the cell. It is shown that the aluminium back contact has a complex microstructure, consisting of five main components: 1) the back surface field layer;2) a eutectic layer;3) spherical (3 - 5 μm) hypereutectic Al-Si particles surrounded by a thin aluminium oxide layer (200 nm);4) a bis- muth-silicate glass matrix;and 5) pores (14 vol%). It was concluded that the eutectic layer thickness and waviness depends on Al particle size, amount of Al paste and textured surface roughness of silicon wafers. The Young’s modulus of the Al-Si particles is estimated by nano-indentation and the overall Young’s modulus is estimated on the basis of bowing measurements and found to be ~43 GPa. It was found, that there is a relation between aluminium paste composition, eutectic layer thickness, mechanical strength and bowing of solar cells. Three main parameters were found to affect the mechanical strength of mc-silicon solar cells with an aluminium contact layer, namely the eutectic layer thickness and uniformity, the Al layer thickness (which results from the Al particle size and its distribution), and the amount of porosity and the bismuth glass fraction.
文摘CuCr25W1Ni2 alloy was prepared by means of vacuum induction melting (VIM). A series of Cu/Cr alloys with different compositions (mass fraction, 25%～75%) and Cr grain sizes (up to 150 μm) were investigated for their differences in physical properties and breakdown voltage. The influence of alloy elements and microstructure on the performance of CuCr25W1Ni2 alloy was also discussed. Experimental results show that the chromium phase is strengthened and its size is minimized by the addition of tungsten powder. After electrical breakdown, very fine tungsten particles in the melt layer form the external nuclei in the solidification process. The microstructure of surface melt layer of CuCr25W1Ni2 alloy is much flatter. It can notably improve the dielectric strength. On the other hand, the nickel can enhance the mutual solubility of copper and chromium, and the whole alloy is strengthened. [
