Auto-parametric resonance of a continuous-beam-bridge model under two-point periodic excitation:an experimental investigation and stability analysis

The auto-parametric resonance of a continuous-beam bridge model subjected to a two-point periodic excitation is experimentally and numerically investigated in this study.An auto-parametric resonance experiment of the test model is conducted to observe and measure the auto-parametric resonance of a continuous beam under a two-point excitation on columns.The parametric vibration equation is established for the test model using the finite-element method.The auto-parametric resonance stability of the structure is analyzed by using Newmark's method and the energy-growth exponent method.The effects of the phase difference of the two-point excitation on the stability boundaries of auto-parametric resonance are studied for the test model.Compared with the experiment,the numerical instability predictions of auto-parametric resonance are consistent with the test phenomena,and the numerical stability boundaries of auto-parametric resonance agree with the experimental ones.For a continuous beam bridge,when the ratio of multipoint excitation frequency(applied to the columns)to natural frequency of the continuous girder is approximately equal to 2,the continuous beam may undergo a strong auto-parametric resonance.Combined with the present experiment and analysis,a hypothesis of Volgograd Bridge's serpentine vibration is discussed.

Analysis of inhomogeneity of solidified microstructure of continuous casting copper tubular billet based on factor analysis

The horizontal continuous casting process,the initial step in TP2 copper tubular processing,directly determines the microstructure and properties of copper tubular.However,the process parameters of the continuous casting characterize time variation,multiple disturbances and strong coupling.As a consequence,their influence on a casting billet is difficult to be determined.Due to the above issues,the common factor and special factor analysis of the factor analysis model were used in this study,and the casting experiment and billet metallographic experiment were carried out to diagnose and analyze the reason of the microstructure inhomogeneity.The multiple process parameters were studied and classified using common factor analysis,2 the cast billets with abnormal microstructures were identified by GT^(2) statistics,and the most important factors affecting the microstructural homogeneity were found by special factor analysis.The calculated and experimental results show that the principal parameters influencing the inhomogeneity of solidified microstructure are the primary inlet water pressure and the primary outlet water temperature.According to the consequence of the above investigation,the inhomogeneity of the copper billet microstructure can be effectively improved when the process parameters are controlled and adjusted.

Spectroscopic Leaf Level Detection of Powdery Mildew for Winter Wheat Using Continuous Wavelet Analysis

Powdery mildew （Blumeria graminis） is one of the most destructive crop diseases infecting winter wheat plants, and has devastated millions of hectares of farmlands in China. The objective of this study is to detect the disease damage of powdery mildew on leaf level by means of the hyperspectral measurements, particularly using the continuous wavelet analysis. In May 2010, the reflectance spectra and the biochemical properties were measured for 114 leaf samples with various disease severity degrees. A hyperspectral imaging system was also employed for obtaining detailed hyperspectral information of the normal and the pustule areas within one diseased leaf. Based on these spectra data, a continuous wavelet analysis （CWA） was carried out in conjunction with a correlation analysis, which generated a so-called correlation scalogram that summarizes the correlations between disease severity and the wavelet power at different wavelengths and decomposition scales. By using a thresholding approach, seven wavelet features were isolated for developing models in determining disease severity. In addition, 22 conventional spectral features （SFs） were also tested and compared with wavelet features for their efficiency in estimating disease severity. The multivariate linear regression （MLR） analysis and the partial least square regression （PLSR） analysis were adopted as training methods in model mildew on leaf level were found to be closely related with the development. The spectral characteristics of the powdery spectral characteristics of the pustule area and the content of chlorophyll. The wavelet features performed better than the conventional SFs in capturing this spectral change. Moreover, the regression model composed by seven wavelet features outperformed （R2=0.77, relative root mean square error RRMSE=0.28） the model composed by 14 optimal conventional SFs （R2---0.69, RRMSE--0.32） in estimating the disease severity. The PLSR method yielded a higher accuracy than the MLR method. A combination of CWA and PLSR was found to be promising in providing relatively accurate estimates of disease severity of powdery mildew on leaf level.

POWER FLOW ANALYSIS AND APPLICATION SIMULATION OF ELECTROMAGNETIC CONTINUOUSLY VARIABLE TRANSMISSION

With the structure of two air gaps and two rotors, the electromagnetic continuously variable transmission（EMCVT） is a novel power-split continuously variable transmission（CVT）. There are two kinds of power flowing through the EMCVT, one is mechanical power and the other is electric power. In the mean time, there are three power ports in the EMCVT, one is the outer rotor named mechanical power port and the other two are the inner rotor and the stator named electric power ports. The mechanical power port is connected to the driving wheels through the final gear and the electric ports are connected to the batteries through the transducers. The two kinds of power are coupled on the outer rotor of the EMCVT. The EMCVT can be equipped on the conventional vehicle being regarded as the CVT and it also can be equipped on the hybrid electric vehicle（HEV） as the multi-energy sources assembly. The power flows of these two kinds of applications are analysed. The back electromotive force（EMF） equations are illatively studied and so the dynamic mathematic model is theorized. In order to certify the feasibility of the above theories, three simulations are carried out in allusion to the above two kinds of mentioned applications of the EMCVT and a five speed automatic transmission（AT） vehicle. The simulation results illustrate that the efficiency of the EMCVT vehicles is higher than that of the AT vehicle owed to the optimized operation area of the engine. Hence the fuel consumption of the EMCVT vehicles is knock-down.

Continuous flow analysis of dissolved total phosphorus in seawater by UVK_(2)S_(2)O_(8) online digestion method

Several methods for analysis of dissolved total phosphorus in seawater were reviewed. Discussions were focused on UVirradiation and persulphate oxidation methods which are the most popular dissolved organic phosphorus determinationmethods presently. The compounds used for the phosphorus recovery test were categorized into three groups accordingto their chemical structure. It was found that low power UV irradiation can decompose POC or PC bonds efficientlybut may be inefficient for POP bonds. Heating-bath in acid condition is useful for decomposing POP bonds. Usingthe continuous flow analysis system (Auto-analyzer II), UV digestion and heating-bath, series experiments were carriedout based on the above analysis. Eleven model compounds were employed for the phosphorus recovery test and thefactors influencing the decomposition efficiency of dissolved compounds containing phosphorus were clarified. Finally,the optimal design for determination of dissolved total phosphorus in seawater based on the routine continuous flowanalysis system was presented. For the organic mono-phosphate, the recovery is more than 90% and a recovery of33%~51% was obtained for inorganic or organic polyphosphates. Up to now, this is the highest decompositionefficiency for dissolved phosphorus based on the continuous flow analysis system.

Furnace structure analysis for copper flash continuous smelting based on numerical simulation

According to the innate characteristic of four types of furnace, the copper flash continuous smelting （CFCS） furnace can be considered a synthetic reactor of two relatively independent processes： flash matte smelting process （FMSP） and copper continuous converting process （CCCP）. Then, the CFCS thermodynamic model was proposed by establishing the multi-phase equilibrium model of FMSP and the local-equilibrium model of CCCP, respectively, and by combining them through the smelting intermediates. Subsequently, the influences of the furnace structures were investigated using the model on the formation of blister copper, the Fe3O4 behavior, the copper loss in slag and the copper recovery rate. The results show that the type D furnace, with double flues and a slag partition wall, is an ideal CFCS reactor compared with the other three types furnaces. For CFCS, it is effective to design a partition wall in the furnace to make FMSP and CCCP perform in two relatively independent zones, respectively, and to make smelting gas and converting gas discharge from respective flues.

An Empirical Application of User-Guided Program Analysis

Although static program analysis methods are frequently employed to enhance software quality,their efficiency in commercial settings is limited by their high false positive rate.The EUGENE tool can effectively lower the false positive rate.However,in continuous integration(CI)environments,the code is always changing,and user feedback from one version of the software cannot be applied to a subsequent version.Additionally,people find it difficult to distinguish between true positives and false positives in the analytical output.In this study,we developed the EUGENE-CI technique to address the CI problem and the EUGENE-rank lightweight heuristic algorithm to rate the reports of the analysis output in accordance with the likelihood that they are true positives.On the three projects ethereum,go-cloud,and kubernetes,we assessed our methodologies.According to the trial findings,EUGENE-CI may drastically reduce false positives while EUGENE-rank can make it much easier for users to identify the real positives among a vast number of reports.We paired our techniques with GoInsight~1 and discovered a vulnerability.We also offered a patch to the community.

CAUCHY TYPE INTEGRALS AND A BOUNDARY VALUE PROBLEM IN A COMPLEX CLIFFORD ANALYSIS

Clifford analysis is an important branch of modern analysis;it has a very important theoretical significance and application value,and its conclusions can be applied to the Maxwell equation,Yang-Mill field theory,quantum mechanics and value problems.In this paper,we first give the definition of a quasi-Cauchy type integral in complex Clifford analysis,and get the Plemelj formula for it.Second,we discuss the H?lder continuity for the Cauchy-type integral operators with values in a complex Clifford algebra.Finally,we prove the existence of solutions for a class of linear boundary value problems and give the integral representation for the solution.

A novel method for gamma spectrum analysis of low-level and intermediate-level radioactive waste

The uncertainty of nuclide libraries in the analysis of the gamma spectra of low-and intermediate-level radioactive waste(LILW)using existing methods produces unstable results.To address this problem,a novel spectral analysis method is proposed in this study.In this method,overlapping peaks are located using a continuous wavelet transform.An improved quadratic convolution method is proposed to calculate the widths of the peaks and establish a fourth-order filter model to estimate the Compton edge baseline with the overlapping peaks.Combined with the adaptive sensitive nonlinear iterative peak,this method can effectively subtracts the background.Finally,a function describing the peak shape as a filter is used to deconvolve the energy spectrum to achieve accurate qualitative and quantitative analyses of the nuclide without the aid of a nuclide library.Gamma spectrum acquisition experiments for standard point sources of Cs-137 and Eu-152,a segmented gamma scanning experiment for a 200 L standard drum,and a Monte Carlo simulation experiment for triple overlapping peaks using the closest energy of three typical LILW nuclides(Sb-125,Sb-124,and Cs-134)are conducted.The results of the experiments indicate that(1)the novel method and gamma vision(GV)with an accurate nuclide library have the same spectral analysis capability,and the peak area calculation error is less than 4%;(2)compared with the GV,the analysis results of the novel method are more stable;(3)the novel method can be applied to the activity measurement of LILW,and the error of the activity reconstruction at the equivalent radius is 2.4%;and(4)The proposed novel method can quantitatively analyze all nuclides in LILW without a nuclide library.This novel method can improve the accuracy and precision of LILW measurements,provide key technical support for the reasonable disposal of LILW,and ensure the safety of humans and the environment.

Analysis of a Typical Case of Meteorological Service in Tangpu Reservoir

The continuous rainy precipitation process from February to March in 2019 was selected to analyze the effect of meteorological service in Tangpu Reservoir basin,so as to sum up service experience and then lay a better foundation for subsequent services.In response to the rainy weather from December 2018 to early 2019,three rounds of flood discharge were carried out in Tangpu Reservoir.During February-March in 2019,the hit rate of short-term area rainfall forecast for Tangpu Reservoir was 80.0%.Compared with the median of forecast interval,the average absolute error was 7.6 mm,and the relative error was 32.7%.The large deviation in the forecast from March 27 to 28 was deeply analyzed,and it is found that the main reasons were excessive reliance on and trust in a single model,insufficient correction of the actual situation,and insufficient judgment of the nature of precipitation.For the future reservoir meteorological service,three aspects of thinking were put forward,such as further strengthening the sharing of hydrological and meteorological information,improving the forecasting ability,and deepening the research of runoff forecast models.

Analysis of the Maximum Continuous Precipitation Variation in Shenyang in 48 Years

[Objective] The aim was to study the changes of maximum continuous precipitation in Shenyang in recent 48 years.[Method] By dint of the daily precipitation from May to September from 1961 to 2008 and according to simple linear trend estimates and microwave analysis,the maximum consecutive precipitation in each month was analyzed.[Result] The frequency of extreme value for the maximum consecutive precipitation in Shenyang increased since 1990.The decreasing trend of maximum consecutive precipitation from May to September was consistent with that around 1990.The decrease of maximum consecutive precipitation amount had tendency to decrease along with the passing of time.There was 5 years temporal scale period of maximum consecutive precipitation from May to September in Shenyang.Maximum value occurred in 1973 and the minimum value occurred in 2000.[Conclusion] The study had important reality meaning to the understanding of climate changes in Shenyang and disaster prevention and relief work of extreme climate incidents.

3D FE Analysis of Thermal Behavior of Billet in Rod and Wire Hot Continuous Rolling Process

An FE model was developed to study thermal behavior during the rod and wire hot continuous rolling process. The FE code MSC. Marc was used in the simulation using implicit static arithmetic. The whole rolling process of 30 passes was separated and simulated with several continuous 3D elastic-plastic FE models. A rigid pushing body and a data transfer technique were introduced into this model. The on-line experiments were conducted on 304 stainless steel and GCr15 steel hot continuous rolling process to prove the results of simulation by implicit static FEM. The results show that the temperature results of finite element simulations are in good agreement with experiments, which indicate that the FE model developed in this study is effective and efficient.

Climatic Analysis of Continuous Rain in Southwest of Shandong

The continuous rain data from 1961 to 2007 in Heze city was analyzed in this paper.The results showed that continuous rain increased from north to south.Continuous rain processes took place most frequently in summer,next in autumn,and the least in winter.Using wavelet to analyze the sequence of seasonal and annual continuous rain,it had a 5 years cycle oscillation at 2Y(year) level and a 20 years cycle oscillation at 10Y level.An abrupt climate change of continuous rain took place in 1986.Continuous rain was in a more period from 2001 to 2010 and would decrease gradually within the period.

Temperature field analysis and its application in hot continuous rolling of Inconel 718 superalloy

A coupled thermo-mechanical model containing metal flow and temperature field for calculating temperature variation has been developed on fourteen-pass hot continuous rolling of round rod for Inconel 718 alloy using 3D elastic-plastic finite element method （FEM）. The temperature of characteristic analysis points in the intermediate cross-section of the workpiece has been simulated at initial temperature ranging from 960 to 1000 ℃ and initial velocity in range of 0.15-0.55 m·s^-1. Based on finite element analysis and microstructural observation in cylindrical hot compression experiments, the appropriate hot continuous rolling technologies have been designed for rod products with different diameters. For a real rolling practice, the simulated surface temperature was examined and is in good agreement with the measured one.

Possibility for Recognition of Psychic Brain Activity with Continuous Wavelet Analysis of EEG

The brain is a unique organization in nature, possessing the ability for psychic activity, which manifests itself in thoughts, feelings and emotions. In present days, numbers of mathematical methods for analysis of electroencephalogram (EEG) were developed with continuous wavelet transform being one of the most successive approaches for studying of brain activity. This paper is aimed to develop methods for investigation of psychic brain activity with help of continuous wavelet analysis of EEG. Ability of human to realize semantic content of the image presented on the screen was tested. Experiment was accompanied with simultaneous EEG recording, which was held with developed software and PC-based experimental setup. The information capabilities of continuous wavelet transform-based method for EEG analysis were improved for the recognition of specific patterns in human brain activity. Comparative wavelet analysis was carried out for EEG recordings at the moment of awareness of the semantic content of the image and for EEG recordings in the absence of conscious (subjective) perception of the semantic content of the image. Significant differences were shown in the alpha rhythm of EEG for the moments of awareness of the semantic content of the image and for the moments of absence of conscious perception. Continuous wavelet analysis of EEG showed that the alpha rhythm is the main EEG rhythm, which can be used to estimate the presence of subjective perception of the visual image. Significant differences were shown in the alpha rhythm of EEG for the moments of awareness of the semantic content of the image and for the moments of absence of conscious perception. Conducted studies allow to conclude that revealing of brain activity related to visual image awareness is possible through analysis of EEG.

Modeling and Dynamic Analysis of Fractional-Order Buck Converter in Continuous Conduction Mode

According to the fact that the actual inductor and actual capacitor are fractional, the mathematical and state-space averaging models of fractional order Buck converters in continuous conduction mode(CCM) are constructed by using fractional calculus theory. Firstly, the parameter conditions that ensure that the converter working in CCM is given and transfer functions are derived. Also, the inductor current and the output voltage are analyzed. Then the difference between the mathematical model and the circuit model are analyzed, and the effect of fractional order is studied by comparing the integer order with fractional order model. Finally, the dynamic behavior of the current-controlled Buck converter is investigated. Simulation experiments are achieved via the use of Matlab/Simulink. The experimental results verify the correctness of theoretical analysis, the order should be taken as a significant parameter. When the order is taken as a bifurcation parameter, the dynamic behavior of the converter will be affected and bifurcation points will be changed as order varies.

Analysis of a Rare Continuous Rainy Process in Midsummer

[Objective] The research aimed to analyze a rare low temperature and rainy weather process which happened in Anhui Province from July 22 to August 14,2009.[Method] Based on the data of conventional observation,NCEP analysis field and automatic station,a rare low temperature and rainy weather process which occurred in Anhui Province from July 22 to August 14,2009 was analyzed.The formation reason of continuous rainy process in midsummer was discussed.The circulation characteristics and influence systems of continuous rainy process were revealed.On the base,the influences of configuration of circulation fields and difference of physical quantity fields at high and low layers on range and intensity of precipitation were analyzed.[Result] According to the circulation situation and influence system,the continuous rainy process could be divided into four stages:July 22-24,from July 27 to August 1,August 4-8 and August 9-14.Moreover,it was respectively affected by northeast low vortex,cold and warm air,high-level low trough,typhoon and periphery of subtropical high at four stages.The maintenance of big specific humidity zone provided sufficient water vapor condition for the continuous rainy weather.The rainstorm appeared in dense zone of specific humidity line,where the specific humidity >13 g/kg in the humidity front zone.A temperature trough maintained at 850 hPa.The cold air which continued to diffuse and go south was main reason of the abnormally low temperature during the continuous rainy period.Moreover,it provided ascending motion condition for precipitation maintenance.[Conclusion] The research provided references for actual forecast of continuous rainy weather.

Analysis of sp Pillar Stability Experiment: Continuous thermo-mechanical model development and calibration

The paper describes an analysis of thermo-mechanical （TM） processes appearing during the Aspo Pillar Stability Experiment （APSE）. This analysis is based on finite elements with elasticity, plasticity and dam- age mechanics models of rock behaviour and some least squares calibration techniques. The main aim is to examine the capability of continuous mechanics models to predict brittle damage behaviour of gran- ite rocks. The performed simulations use an in-house finite element software GEM and self-developed experimental continuum damage MATLAB code. The main contributions are twofold. First, it is an inverse analysis, which is used for （1） verification of an initial stress measurement by back analysis of conver- gence measurement during construction of the access tunnel and （2） identification of heat transfer rock mass properties by an inverse method based on the known heat sources and temperature measurements. Second, three different hierarchically built models are used to estimate the pillar damage zones, i.e. elas- tic model with Drucker-Prager strength criterion, elasto-plastic model with the same yield limit and a combination of elasto-plasticity with continuum damage mechanics. The damage mechanics model is also used to simulate uniaxial and triaxial compressive strength tests on the ,Aspo granite.

Continuous regional arterial infusion for the treatment of severe acute pancreatitis: a meta-analysis

BACKGROUND： Continuous regional arterial infusion（CRAI） is a drug delivery system, which dramatically increases the drug concentration in the pancreas. Previous clinical and basic studies have demonstrated the possible therapeutic efficacy of CRAI for severe acute pancreatitis（SAP）. This meta-analysis of all published randomized controlled trials（RCTs） was conducted to assess the efficacy and safety of CRAI for the treatment of SAP. DATA SOURCES： Up to August 10, 2014, RCTs comparing CRAI with intravenous infusion for SAP in PubM ed, Embase, EBSCO, MEDLINE, Science Citation Index Expanded, Cochrane Library, China Academic Journals Full-Text Database, Chinese Biomedical Literature Database, and Chinese Scientific Journals Database were selected by two independent reviewers. The relative risk（RR） and their 95% confidence intervals（CI） for duration of elevated serum amylase and urine amylase, duration of abdominal pain, infection rate, incidence of complication, overall mortality, curative rate, hospital stay and details of subgroup analysis were extracted. Meta-analyses were made using the software Review Manager（RevM an version 5.10）.RESULTS： Six RCTs with 390 patients meeting the inclusion criteria were included in the final analysis. Compared with intravenous infusion route, CRAI significantly shortened the duration of elevated urine amylase（MD=-2.40, 95% CI=-3.20,-1.60; P〈0.00001） and the duration of abdominal pain（MD=-1.46, 95% CI=-1.94,-0.98; P〈0.00001）, decreased the incidence of complication（RR=0.35, 95% CI=0.15, 0.81; P=0.01） and overall mortality（RR=0.25, 95% CI=0.08, 0.78;P=0.02）, shortened the duration of hospital stay（MD=-10.36, 95% CI=-17.05,-3.68; P=0.002）, and increased the curative rate（RR=1.66, 95% CI=1.13, 2.46; P=0.01）. No mortality and catheter-related infections due to CRAI administration was reported in these studies. Subgroup analysis showed that the combination of drug administration via CRAI did not significantly improve the outcomes.CONCLUSION： CRAI is effective for the treatment of SAP, and the combination of drug administration via CRAI did not have a significant effect on the improvement of the outcomes.

Seismic analysis of long-span continuous rigid frame bridges in cold regions:a case study of Bridge 1 in north of international tourism resort in Changbai Mountain

It is helpful to improve the seismic design theory of long-span continuous bridges for studying the seismic performance of each cantilever construction state.Taking the Bridge 1 in the north of Changbai-Mountain international tourism resort as an example,the authors studied it in shutdown phase and the cantilever construction process,established the simulation model by using Midas / civil,and analyzed time-history of each construction stage for the bridge.The study shows that long-span bridge cantilever construction in northeastern China can be divided into two-year tasks for construction(suspending in winter).It is needed to think about seismic stability of the cantilever position in shut-down phase of winter.The effect of longitudinal vibration is the most disadvantageous influence to bridge,and its calculation results can provide reference for seismic design of similar bridges in the future.