Recent Advances in Interface Modification of Cu/graphite Composites and Layered Ternary Carbides of Modified Layer Candidate

We review the fundamental properties and significant issues related to Cu/graphite composites.In particular,recent research on the interfacial modification of Cu/graphite composites is addressed,including the metal-modified layer,carbide-modified layer,and combined modified layer.Additionally,we propose the use of ternary layered carbide as an interface modification layer for Cu/graphite composites.

Protective Graphite Coating for Two-Dimensional Carbon/Carbon Composites

Two-dimensional carbon/carbon(2D C/C)composites are a special class of carbon/carbon composites,generally obtained by combining resin-impregnated carbon fiber clothes,which are then cured and carbonized.This study deals with the preparation of a protective coating for these materials.This coating,based on graphite,was prepared by the slurry method.The effect of graphite and phenolic resin powders with different weight ratios was examined.The results have shown that the coating slurry can fill the pores and cracks of the composite surface,thereby densifying the surface layer of the material.With the increase of the graphite powder/phenolic resin weight ratio,the coating density is enhanced while the coating surface flatness decreases;moreover,the protective ability of coating against erosion first increases(from 1:3 to 2:2)and then decreases(from 2:2 to 3:1).When the weight ratio is about 1:1,the coating for 2D C/C composites exhibits the best erosion resistance,which greatly aids these materials during gas quenching.In this case,the erosion rate is decreased by approximately 41.5%at the impact angle of 30°and 52.3%at normal impact,respectively.This can be attributed to the ability of the coating slurry to infiltrate into the substrate,thereby bonding the fibers together and increasing the compactness of the 2D C/C composites.

Sliding wear behavior of copper-based composites reinforced with graphene nanosheets and graphite

The mechanical and tribological properties of hot-pressed copper-based composites containing different amounts of graphene nanosheets（GNSs） are compared with those of copper-graphite（Gr） composites fabricated by the same method.The results show that the Cu-GNSs composites exhibit higher relative density,microhardness and bending strength compared with Cu-Gr composites with the same volume fraction of GNSs and Gr.Moreover,the friction coefficients and wear rates reduce significantly by the addition of GNSs,whereas the limited impact on reducing friction and wear is found on graphite.The abrasive and delamination wear are the dominant wear mechanisms of the composites.It is believed that the superior mechanical and tribological performances of Cu-GNSs composites are attributed to the unique strengthening effect as well as the higher lubricating efficiency of graphene nanosheets compared with those of graphite,which demonstrates that GNS is an ideal filler for copper matrix composites,acting as not only an impactful lubricant but also a favorable reinforcement.

Sintering behavior and thermal conductivity of nickel-coated graphite flake/copper composites fabricated by spark plasma sintering

Nickel-coated graphite flakes/copper（GN/Cu） composites were fabricated by spark plasma sintering with the surface of graphite flakes（GFs） being modified by Ni–P electroless plating. The effects of the phase transition of the amorphous Ni–P plating and of Ni diffusion into the Cu matrix on the densification behavior, interfacial microstructure, and thermal conductivity（TC） of the GN/Cu composites were systematically investigated. The introduction of Ni–P electroless plating efficiently reduced the densification temperature of uncoated GF/Cu composites from 850 to 650℃ and slightly increased the TC of the X–Y basal plane of the GF/Cu composites with 20 vol%–30 vol% graphite flakes. However, when the graphite flake content was greater than 30 vol%, the TC of the GF/Cu composites decreased with the introduction of Ni–P plating as a result of the combined effect of the improved heat-transfer interface with the transition layer, P generated at the interface, and the diffusion of Ni into the matrix. Given the effect of the Ni content on the TC of the Cu matrix and on the interface thermal resistance, a modified effective medium approximation model was used to predict the TC of the prepared GF/Cu composites.

Effect of WS_2 addition on electrical sliding wear behaviors of Cu-graphite-WS_2 composites

Four kinds of Cu-based composites with different mass ratios of graphite and WS2 as lubricants were fabricated by hot-pressing method. Electrical sliding wear behaviors of the composites were investigated using a block-on-ring tribometer rubbing against Cu-5%Ag alloy ring. The results demonstrated that 800 ~C was the optimum sintering temperature for Cu-graphite-WS2 dual-lubricant composites to obtain the best comprehensive properties of mechanical strength and lubrication performance. Contact voltage drops of the Cu-based composites increased with increasing the mass ratio of WS2 to graphite. The Cu-based composite with 20% graphite and 10% WS2 showed the best wear resistance due to the excellent synergetic lubricating effect of graphite and WS2. The reasonable addition of WS2 into the Cu-graphite composite can remarkably improve the wear resistance without much rise of electrical energy loss which provides a novel principle of designing suitable sliding electrical contact materials for industrial applications.

Enhanced Thermal Conductivity and Bending Strength of Graphite Flakes/aluminum Composites Via Graphite Surface Modification

The effect of graphite surface modification on the thermal conductivity(TC) and bending strength of graphite flakes/Al composites(Gf/Al) prepared by gas pressure infiltration were investigated. Al3 Ni and Al4C3 phase may form at the interface in Ni-coated Gf/Al and uncoated Gf/Al composites, respectively, while the Al-Cu compound cannot be observed in Cu-coated Gf/Al composites. The Cu and Ni coatings enhance TC and the bending strength of the composites in the meantime. TC of Cu-coated Gf/Al composites reach 515 Wm^-1·K^-1 with 75 vol% Gf, which are higher than that of Ni-coated Gf/Al. Meanwhile, due to Al3 Ni at the interface, the bending strength of Ni-coated Gf/Al composites are far more than those of the uncoated and Cu-coated Gf/Al with the same content of Gf. The results indicate that metal-coated Gf can effectively improve the interfacial bonding between Gf and Al.

Preparation of Expanded Graphite-based Composites by One Step Impregnation

A new method for preparing expanded graphite-based composites （EGCs） was developed.The obtained samples were characterized by scanning electron microscopy （SEM）,transmission electron microscope （TEM） and nitrogen adsorption.The experimental results indicated that the EGCs was not simply mechanical mixture of EG and activated carbon,instead the activated carbon was coated on the surface of interior and external pores of the EG in the form of thin carbon layer.The thickness of the activated carbon layer was nearly one hundred nanometers by calculation.It was shown that the higher the impregnation ratio and the activation temperature were,the easier the porosity development would be.And the BET surface area and the total pore volume were as high as 1978 m2/g and 0.9917 cm3/g respectively at 350℃ with an impregnation ratio of 0.9.

Effect of graphite powder as a forming filler on the mechanical properties of SiCp/Al composites by pressure infiltration

（38vo1% SiCp ＋ 2vo1% A1203f）/2024 A1 composites were fabricated by pressure infiltration. Graphite powder was introduced as a forming filler in preform preparation, and the effects of the powder size on the microstructures and mechanical properties of the final com- posites were investigated. The results showed that the composite with 15 μm graphite powder as a forming filler had the maximum tensile strength of 506 MPa, maximum yield strength of 489 MPa, and maximum elongation of 1.2%, which decreased to 490 MPa, 430 MPa, and 0.4%, respectively, on increasing the graphite powder size from 15 to 60 μm. The composite with 60 μm graphite powder showed the highest elastic modulus, and the value decreased from 129 to 113 GPa on decreasing the graphite powder size from 60 to 15 μm. The differences between these properties are related to the different microstructures of the corresponding composites, which determine their failure modes.

Composites on Base of the Ultradispersed Polytetrafluoroethylene and Graphite Oxide Intercalated Compounds

Composites based on ultradispersed polytetrafluoroethylene and intercalated graphite oxide compounds with dodecahydro-closo-dodecaborates and methods of their fabrication have been developed. The fabricated composites have been characterized using XRD analysis, and optical microscopy. These composites are distinguished with completeness of their combustion, since the combustion products comprise gaseous boron fluorine-containing compounds of boron, boron trifluoride (BF3), and boron oxyfluoride ((BOF)3). Besides, these composites are characterized with increased energy capacity as compared to purely oxygen-containing compounds, since the heat of formation of boron fluorine-containing compounds is higher than that of boron oxide. Introduction of ultradispersed polytetrafluoroethylene imparts composites with hydrophobicity, thus improving their functioning properties.

Piezoresistivity of Carbon Fiber Graphite Cement-based Composites with CCCW

The electrical conductivity and piezoresistivity of carbon fiber graphite cement-matrix composites（CFGCC） with carbon fiber content（1% by the weight of cement）,graphite powder contents （0%-50% by the weight of cement） and CCCW（cementitious capillary crystalline waterproofing materials,4% by the weight of cement） were studied.The experimental results showed that the relationship between the resistivity of CFGCC and the concentration of graphite powders had typical features of percolation phenomena.The percolation threshold was about 20%.A clear piezoresistive effect was observed in CFGCC with 1wt% of carbon fibers,20wt% or 30wt% of graphite powders under uniaxial compressive tests,indicating that this type of smart composites was a promising candidate for strain sensing.The measured gage factor （defined as the fractional change in resistance per unit strain） of CFGCC with graphite content of 20wt% and 30wt% were 37 and 22,respectively.With the addition of CCCW,the mechanical properties of CFGCC were improved,which benefited CFGCC piezoresistivity of stability.

Tribological behaviors of Ag-graphite composites reinforced with spherical graphite

Two kinds of Ag-graphite composites reinforced with spherical graphite(SG)and conventional flake graphite(FG)were prepared by powder metallurgy technology.The effect of graphite morphology on the tribological behavior for the Ag-SG and Ag-FG under the dry sliding wear was investigated with a pin-on-disk tribometer at a load of 3.0 N in atmosphere condition.The results indicated that the minimum wear rate of 3.5×10^-5 mm^3/(N·m)for Ag-FG was achieved and it reduced by nearly an order of magnitude,reaching 1.6×10^-6 mm^3/(N·m)for the Ag-SG.The obviously different tribological behaviors between the Ag-SG and Ag-FG were closely related to the formation of cracks in the sub-surface.The stress concentration tended to generate at the edges of flake graphite during sliding process,which resulted in the cracks and severe delamination wear of Ag-FG.However,no cracks were found around the spherical graphite in Ag-SG.The spherical graphite can effectively inhibit the initiation and propagation of cracks,achieving high wear resistance.

Effects of graphite on the microstructure and properties of ultrafine WC-11Co composites by spark plasma sintering

Ultrafine WC-11Co hard metals added with different proportions of graphite were prepared by spark plasma sintering at 40 MPa/1200°C for 5 min,and the influence of graphite as free carbon on the microstructure and mechanical properties were investigated.The XRD analysis showed that decarbonization could be prevented by adding graphite.Compact hard metals composed of finer and more homogeneous WC grains with little flaws can be achieved after 0 wt.% to 1.5 wt.% graphite was added.The hardness and fracture toughness increase initially with increasing graphite content,and with over 1.5 wt.% they descend due to coarse grains and more defects.Therefore,1.5 wt.% graphite is the optimal addition content in view of the hardness and transverse rupture toughness.Furthermore,the coercive force decreases while the saturated magnetic intensity increases with the increase of graphite content.

Effect of filler on the self-lubrication performance of graphite antimony composites

Graphite antimony composites were prepared using a mechanical pressure infiltration method to force molten antimony into graphite preforms having a percolation micro-structure and a hop-pocket power filler. The micro-structural and macroscopic properties of the graphite antimony composites were analysed. Observations included metallographic analysis, physical properties and friction and wear behaviour. The results show that the wear loss is decreased by 12.24% and that the friction coefficient is re-duced by 32.61% after hop-pocket power was used. The research indicates that the hop-pocket power method gives a useful way to reduce friction coefficients and wear loss, and to increase service life and self-lubrication properties, of the graphite antimony seal-ing material as compared to carbon black.

Microstructure and properties of high-fraction graphite nanoflakes/6061Al matrix composites fabricated via spark plasma sintering

30-50 wt.%graphite nanoflakes(GNFs)/6061Al matrix composites were fabricated via spark plasma sintering(SPS)at 610℃.The effects of the sintering pressure and GNF content on the microstructure and properties of the composites were investigated.The results indicated that interfacial reactions were inhibited during SPS because no Al4C3 was detected.Moreover,the agglomeration of the GNFs increased,and the distribution orientation of the GNFs decreased with increasing the GNF content.The relative density,bending strength,and coefficient of thermal expansion(CTE)of the composites decreased,while the thermal conductivity(TC)in the X−Y direction increased.As the sintering pressure increased,the GNFs deagglomerated and were distributed preferentially in the X−Y direction,which increased the relative density,bending strength and TC,and decreased the CTE of the composites.The 50wt.%GNFs/6061Al matrix composite sintered at 610℃ under 55 MPa demonstrated the best performance,i.e.,bending strength of 72 MPa,TC and CTE(RT−100℃)of 254 W/(m·K)and 8.5×10^(−6)K^(−1)in the X−Y direction,and 55 W/(m·K)and 9.7×10^(−6)K^(−1)in the Z direction,respectively.

Evaluation of sliding wear behavior of graphite particle-containing magnesium alloy composites

The influence of graphite particle content on the friction and wear characteristics of AZ91 magnesium alloy matrix composite was studied. The results show that the wear resistances of graphite-containing composite are much better than those of the matrix under the test conditions. The anti-wear ability of magnesium alloy composite is improved substantially with the increase of the graphite content from 5% to 20%, and both wear mass loss and coefficient of friction are decreased to low level. Different wear mechanisms operate at different sliding stages. A continuous black lubricating film forms progressively on the worn surface along sliding, which effectively limits the direct interaction between the composite tribosurface and the counterpart, and also remarkably delays the transition from mild wear to severe wear for magnesium alloy composite.

Microstructures and wear properties of graphite and Al_2O_3 reinforced AZ91D-Cex composites

The magnesium matrix composites reinforced by graphite particles and Al2O3 short fibers were fabricated by squeeze-infiltration technique.The additions dispersed uniformly and no agglomeration and casting defect were observed.The microstructures and wear properties of the composites with different Ce contents of 0,0.4%,0.8%and 1.0%,respectively,were investigated.Especially,the effect of Ce on the properties was discussed.The results reveal that Ce enriches around the boundaries of graphite particles and forms Al3Ce phase with Al.The addition of Ce refines the microstructures of the composites.With the increase of Ce content,the grain size becomes smaller and the wear resistance of the composite is improved.At low load,the composites have similar worn surface.At high load,the composite with 1.0%Ce has the best wear resistance due to the existence of Al3Ce phase.The Al3Ce phase improves the thermal stability of the matrix so the graphite particles can keep intact,which can still work as lubricant. At low load,the wear mechanism is abrasive wear and oxidation wear.At high load,the wear mechanism changes to delamination wear for all the composites.

Synthesis and Characterization of Exfoliated Graphite/ABS Composites

Exfoliated graphite was prepared by chemical route and then further subjected to thermal oxidation and sonication for size reduction and increased interlayer spacing in natural flake graphite. Exfoliated graphite/ABS composites were pre-pared with varying filler concentration by solution casting method. Exfoliated graphite and composites were character-ised by scanning electron microscopy and energy dispersive X-ray analysis, Fourier transform infrared spectroscopy and X-ray diffractometry techniques. After thermal exfoliation significant peak of graphite at 2? = 26.4? disappeared completely, confirming successful exfoliation of graphite. SEM images revealed homogeneous dispersion of exfoliated graphite in the matrix and EDAX confirmed successful reduction of graphite oxide.

Effect of graphite content on wear property of graphite/Al_2O_3/Mg-9Al-1Zn-0.8Ce composites

Using squeeze-infiltration technique, Mg-9Al-1Zn-0.8Ce composite reinforced by graphite particles and Al2O3 short fibers was fabricated. The reinforcing phases combined closely with the matrix and no agglomeration was observed. The microstructure, hardness and wear property of the composites with the graphite content of 5%, 10%, 15% and 20% were investigated, respectively. The results reveal that Ce tends to enrich around the boundaries of graphite particles and Al2O3 short fibers, and forms Al3Ce phase. When the graphite content increases to 20%, the grain size becomes small. Moreover, with increasing the graphite content, the microhardness of the composites decreases but the wear resistance increases. The graphite which works as lubricant during dry sliding process decreases the wear loss. At low load, the wear mechanism of the composite is mainly abrasive wear and oxidation wear; at high load, except that the composite with 20% graphite is still with abrasive wear and oxidation wear, the wear mechanism of other composites changes to delamination wear.

Poly(lactic acid)-starch/Expandable Graphite (PLA-starch/EG) Flame Retardant Composites

This work reports on the effect of commercial expandable graphite(EG)on the flammability and thermal decomposition properties of PLA-starch blend.The PLA-starch/EG composites were prepared by melt-mixing and their thermal stability,volatile pyrolysis products and flammability characteristics were investigated.The char residues of the composites,after combustion in a cone calorimeter,were analyzed with environmental scanning electron microscopy(ESEM).The thermal decomposition stability of the composites improved in the presence of EG.However,the char content was less than expected as per the combination of the wt%EG added into PLA-starch and the%residue of PLA-starch.The flammability performance of the PLA-starch/EG composites improved,especially at 15 wt%EG content,due to a thick and strong worm-like char structure.The peak heat release rate(PHRR)improved by 74%,the total smoke production(TSP)by 40%and the specific extinction area(SEA)by 55%.The improvements are attributed to the ability of EG to exfoliate at increased temperatures during which time three effects occurred:(i)cooling due to an endothermic exfoliation process,(ii)dilution due to release of H2O,SO2 and CO2 gases,and (iii)formation of a protective intumescent char layer.However,the CO and CO2 yields were found to be unfavorably high due to the presence of EG.

Effect of graphite particle size on wear property of graphite and Al_2O_3 reinforced AZ91D-0.8%Ce composites

The graphite particles and Al_2O_3 short fibers reinforced AZ91D-0.8%Ce composites were fabricated by squeeze-infiltration technique.The researches about the effects of different graphite particle sizes on the microstructure and wear property of the composites were performed under the condition of constant contents of graphite particles and Al_2O_3 short fibers.The results reveal that the grain size of the composites changes less when the graphite particle size descends.Moreover,Ce enriches around the graphite particle and Al_2O_3 short fibers and forms Al_3Ce phase with A1 element.The graphite that works as lubricant decreases the wear loss.The wear resistance of the composites increases as the graphite particle size increases.At low load the composites have similar wear loss;at high load the composite with the largest graphite particle size has the best wear resistance.The wear mechanism of all the composites at low load is abrasive wear and oxidation wear;at high load,except the composites with the particle size of 240μm whose wear mechanism is still abrasive wear and oxidation wear,the wear mechanism of others changes to delamination wear.