MICROALLOYING EFFECT OF BORON ON COPPER-BASE ALLOYS

The microstructure and properties of boron-modified copper-base alloys were investigated by tension,corrosion,corrosive wear and erosion tests.The results show that by adding boron in copper-base alloys,the strength and hardness of alloys increase,the plasticity decreases somewhat;the corrosion,corrosive wear and erosion resistance of boron-modified copper-base alloys improve obviously.The microalloying mechanism of boron in copper-base alloys was found.

COLOR CHARACTERISTICS OF BINARY COPPER-BASE ALLOYS

The effect of Al, Zn, Sn, Mn, Si and Ni on the color characteristics of binary copper-base alloys has been researched systematically and quantitatively. The results show that all alloying elements decrease the red content of an alloy at different levels but have different effects on the yellow color. Al and Zn enhance the yellow content of an alloy, whereas Sn, Mn, Si and Ni decrease the yellow content. When the alloys with different karat gold colors are imitated, Al and Zn are the most important color mixing elements and Sn, Mn, Si and Ni can be used as auxiliary.

Simplified quantitative analysis method and its application in the insitu synthesized copper-based azide chips

Copper-based azide(Cu(N_(3))2 or CuN_(3),CA)chips synthesized by in-situ azide reaction and utilized in miniaturized explosive systems has become a hot research topic in recent years.However,the advantages of in-situ synthesis method,including small size and low dosage,bring about difficulties in quantitative analysis and differences in ignition capabilities of CA chips.The aim of present work is to develop a simplified quantitative analysis method for accurate and safe analysis of components in CA chips to evaluate and investigate the corresponding ignition ability.In this work,Cu(N_(3))2 and CuN_(3)components in CA chips were separated through dissolution and distillation by utilizing the difference in solubility and corresponding content was obtained by measuring N_(3)-concentration through spectrophotometry.The spectrophotometry method was optimized by studying influencing factors and the recovery rate of different separation methods was studied,ensuring the accuracy and reproducibility of test results.The optimized method is linear in range from 1.0-25.0 mg/L,with a correlation coefficient R^(2)=0.9998,which meets the requirements of CA chips with a milligram-level content test.Compared with the existing ICP method,component analysis results of CA chips obtained by spectrophotometry are closer to real component content in samples and have satisfactory accuracy.Moreover,as its application in miniaturized explosive systems,the ignition ability of CA chips with different component contents for direct ink writing CL-20 and the corresponding mechanism was studied.This study provided a basis and idea for the design and performance evaluation of CA chips in miniaturized explosive systems.

Metal-organic-framework-derived copper-based catalyst for multicomponent C-S coupling reaction

Copper-based metal-organic frameworks(Cu-MOFs)are a promising multiphase catalyst for catalyzing C-S coupling reactions by virtue of their diverse structures and functions.However,the unpleasant odor and instability of the organosulfur,as well as the mass-transfer resistance that exists in multiphase catalysis,have often limited the catalytic application of Cu-MOFs in C-S coupling reactions.In this paper,a Cu-MOFs catalyst modified by cetyltrimethylammonium bromide(CTAB)was designed to enhance mass transfer by increasing the adsorption of organic substrates using the long alkanes of CTAB.Concurrently,elemental sulfur was used to replace organosulfur to achieve a highly efficient and atom-economical multicomponent C-S coupling reaction.

Tarnish Testing of Copper-Based Alloys Coated with SiO_2-Like Films by PECVD

The tarnishing test in the presence of hydrogen sulfide（H2S） vapors has been used to investigate the tarnish resistance capability of copper-based alloys coated with Si02-like films by means of plasma-enhanced chemical vapor deposition（PECVD） fed with a tetraethoxysilane/oxygen mixture.The chemical and morphological properties of the films have been characterized by using infrared absorption spectroscopy（IR） and scanning electron microscopy（SEM）with energy disperse spectroscopy（EDS）.The corrosion products of the samples after the tarnishing test have been identified by X-ray diffraction analysis（XRD）.It has been found that SiO2-like films formed via PECVD with a high O2 flow rate could protect copper-based alloys from H2S vapor tarnishing.The alloys coated at the O2 flow rate of 20 sccm remain uncorroded after 54days of H2S vapor tarnish testing.The corrosion products for the alloys deposited at a low O2flow rate after 54 days of tarnish testing are mainly composed of brochantite.

Catalytic combustion of methane over nano ZrO_2-supported copper-based catalysts

The nano ZrO2-supported copper-based catalysts for methane combustion were investigated by means of N2 adsorption, TEM, XRD, H2-TPR techniques and the test of methane oxidation. Two kinds of ZrO2 were used as support, one （ZrO2-1） was obtained from the commercial ZrO2 and the other （ZrO2-2） was issued from the thermal decomposition of zirconium nitrate. It was found that the CuO/ZrO2-2 catalyst was more active than CuO/ZrO2-1. N2 adsorption, H2-TPR and XRD measurements showed that larger surface area, better reduction property, presence of tetragonal ZrO2 and higher dispersion of active component for CuO/ZrO2-2 than that of CuO/ZrO2-1. These factors could be the dominating reasons for its higher activity for methane combustion.

Effect of preparation methods of aluminum emulsions on catalytic performance of copper-based catalysts for methanol synthesis from syngas

Various Cu/ZnO/Al2O3 catalysts have been synthesized by different aluminum emulsions as aluminum sources and their pertormances tor methanol synthesis from syngas have been investigated. The influences of preparation methods of aluminum emulsions on physicochemical and catalytic properties of catalysts were studied by XRD, SEM, XPS,N2 adsorption-desorption techniques and methanol synthesis from syngas. The preparation methods of aluminum emulsions were found to influence the catalytic activity, CuO crystallite size, surface area and Cu0 surface area and reduction process. The results show that the catalyst CN using the aluminum source prepared by addition the ammonia into the aluminum nitrate （NP） exhibited the best catalytic performance for methanol synthesis from syngas.

A highly hydrothermal stable copper-based catalyst for catalytic wet air oxidation of m-cresol in coal chemical wastewater

Catalytic wet air oxidation(CWAO) can degrade some refractory pollutants at a low cost to improve the biodegradability of wastewater. However, in the presence of high temperature and high pressure and strong oxidizing free radicals, the stability of catalysts is often insufficient, which has become a bottleneck in the application of CWAO. In this paper, a copper-based catalyst with excellent hydrothermal stability was designed and prepared. TiO_(2) with excellent stability was used as the carrier to ensure the longterm anchoring of copper and reduce the leaching of the catalyst. The one pot sol–gel method was used to ensure the super dispersion and uniform distribution of copper nanoparticles on the carrier, so as to ensure that more active centers could be retained in a longer period. Experiments show that the catalyst prepared by this method has good stability and catalytic activity, and the catalytic effect is not significantly reduced after 10 cycles of use. The oxidation degradation experiment of m-cresol with the strongest biological toxicity and the most difficult to degrade in coal chemical wastewater was carried out with this catalyst. The results showed that under the conditions of 140℃, 2 MPa and 2 h, m-cresol with a concentration of up to 1000 mg·L^(-1) could be completely degraded, and the COD removal rate could reach 79.15%. The biological toxicity of wastewater was significantly reduced. The development of the catalyst system has greatly improved the feasibility of CWAO in the treatment of refractory wastewater such as coal chemical wastewater.

Comprehensive first-principles studies on phase stability of copper-based halide perovskite derivatives A_lCu_mX_n(A = Rb and Cs;X = Cl, Br, and I)

Recently,inorganic copper-based halide perovskites and their derivatives(CHPs)with chemical formulas AlCumXn(A=Rb and Cs;X=Cl,Br and I;l,m,and n are integers.),have received increasing attention in the photoluminescence field,due to their lead-free,cost-effective,earth-abundant and low electronic dimensionality.Ascribed to flexible valence charge of Cu(Cu1+and Cu2+)and complex competing phases,the crystal structures and phase stabilities of CHPs are complicated and ambiguous,which limits their experimental applications.Via comprehensive first-principles calculations,we have investigated thermodynamic stabilities of possible crystal phases for AlCumXn by considering all the possible secondary phases existing in inorganic crystal structure database(ICSD).Our results are in agreement with existing experiments and further predicted the existence of 10 stable CHPs,i.e.Rb3 Cu2 Br5,Rb3 Cu2 I5,Rb Cu2 Cl3,Rb2 Cu I3,Rb2 Cu Br4,Rb Cu Br3,Rb3 Cu2 Br7,Cs3 Cu2 Br7,Cs3 Cu2 Cl7 and Cs4 Cu5 Cl9,which have not yet been reported in experiments.This work provides a phase and compositional map that may guide experiments to synthesize more novel inorganic CHPs with diverse properties for potential functional applications.

Migration of sulfur in in-situ gasification chemical looping combustion of Beisu coal with iron-and copper-based oxygen carriers

Chemical looping combustion(CLC)is an energy conversion technology with high efficiency and inherent separation of CO_(2).The existence of sulfur in coal may affect the CO_(2) purity and the performance of oxygen carrier due to the interactions between sulfur contaminants and oxygen carrier.The migration of sulfur in Beisu coal during the in-situ gasification chemical looping combustion(i G-CLC)process using two oxygen carriers(iron ore and Cu O/Si O_(2))was investigated respectively.The thermodynamic analysis results showed the formation of metal sulfides was thermodynamically favored at low temperatures and low oxygen excess coefficients,while they were obviously inhibited and the production of SO_(2) was significantly promoted with an increase in temperature and oxygen excess coefficient.Moreover,part of sulfur was captured and fixed in the forms of alkali/alkaline earth metal sulfate due to the high amount of alkali/alkaline earth metal oxides in the coal ash or/and oxygen carrier.The experimental results showed that the sulfur in coal mainly released in the form of SO_(2),and the sulfur conversion efficiency(XS)in the reduction stage were 51.04%and 48.24%when using iron ore and Cu O/Si O_(2) respectively.The existence of metal sulfides was observed in the reduced oxygen carriers.The values of XSin the reoxidation process reached 3.80%and 7.64%when using iron ore and Cu O/Si O_(2) respectively.The residue and accumulation of sulfur were also found on the surfaces of two oxygen carriers.

Effects of Copper-based Nutritional Foliar Fertilizers on Photosynthetic Characteristics,Yield and Disease Control Efficiency of Cotton

[Objectives] The effects of copper-based nutrient foliar fertilizer on photosynthetic characteristics,yield,accumulation and distribution of trace elements in various organs,disease prevention effect and soil enzyme activity were studied,so as to provide a theoretical basis for the application of foliar fertilizers in cotton production. [Methods]Through two years of field experiments,six treatments were set in total,namely spraying water( CK),traditional Bordeaux mixture( BDM),Kocide 2000( KCD),copper-based nutrient foliar fertilizer( CF),iron-copper-based nutrient foliar fertilizer( CFFe),and zinc-boron-copper-based nutrient foliar fertilizer( CFZnB). Randomized block arrangement was adopted. Chlorophyll content in leaves was measured at each growth stage of the cotton. Photosynthetic characteristics of leaves were measured at the peak bolling stage. Plants were sampled at initial boll opening stage. The whole plant was divided into root,stem,leaf and cotton boll parts,in which the total copper,total zinc,total iron contents and accumulations were determined. Soil samples were collected from each plot,followed by the determination of soil enzyme activity. Disease index was investigated at bud,flowering and boll-forming and boll opening stage. [Results]( 1) Spraying CFFe,CFZnB,CF and KCD could significantly improve chlorophyll content of cotton leaves,and the CFFe treatment had the highest increase up to13. 30%,followed by the CFZnB treatment,which was 11. 40% higher than the CK; and photosynthetic rate,stomata conductance and transpiration rate could be improved significantly,and the CFFe treatment showed the highest photosynthetic rate,which increased by 26. 35% compared with the CK,followed by the CFZnB treatment,which increased by 17. 96% compared with CK; and intercellular CO2 concentration was significantly reduced.( 2) Spraying BDM,KCD,CF,CFFe and CFZnB can significantly increase total copper content and accumulation in various cotton organs( except the total copper content in the stem part of the CFZnB treatment; the CFZnB and CFFe treatments can significantly increase total zinc content and accumulation in various cotton organs; and spraying CFFe,CFZnB and CF can significantly increase total iron content and accumulation in various cotton organs( except the total iron content in the stem part of the CF treatment).( 3)Spraying CFFe,CFZnB,CF,KCD and BDM greatly reduced the disease index at flowering and boll-forming and boll opening stages.( 4) The CFZnB and CFFe treatments had the highest soil urease activity,which was 7. 14% higher than that of the CK,but the difference from the CK was not significant; the catalase activity of each treatment was significantly higher than that of the BDM treatment; and the sucrase activity of each treatment was significantly higher than that of the CK.( 5) Spraying CFFe,CFZnB,CF and KCD significantly improved lint yield of cotton,and the CFZnB treatment showed the highest yield increase up to 12. 34%,followed by the CFFe treatment,with an increase in the range of 8. 77%-10. 20%. [Conclusions]Copper-based nutrient foliar fertilizers have dual functions of disease control and prevention and plant nutrition and health care,and not only can significantly increase cotton yield,but also has certain disease prevention effect.It is recommended to use copper-based nutrient foliar fertilizers.

Accelerated design of high-performance Mg-Mn-based magnesium alloys based on novel bayesian optimization

Magnesium(Mg),being the lightest structural metal,holds immense potential for widespread applications in various fields.The development of high-performance and cost-effective Mg alloys is crucial to further advancing their commercial utilization.With the rapid advancement of machine learning(ML)technology in recent years,the“data-driven''approach for alloy design has provided new perspectives and opportunities for enhancing the performance of Mg alloys.This paper introduces a novel regression-based Bayesian optimization active learning model(RBOALM)for the development of high-performance Mg-Mn-based wrought alloys.RBOALM employs active learning to automatically explore optimal alloy compositions and process parameters within predefined ranges,facilitating the discovery of superior alloy combinations.This model further integrates pre-established regression models as surrogate functions in Bayesian optimization,significantly enhancing the precision of the design process.Leveraging RBOALM,several new high-performance alloys have been successfully designed and prepared.Notably,after mechanical property testing of the designed alloys,the Mg-2.1Zn-2.0Mn-0.5Sn-0.1Ca alloy demonstrates exceptional mechanical properties,including an ultimate tensile strength of 406 MPa,a yield strength of 287 MPa,and a 23%fracture elongation.Furthermore,the Mg-2.7Mn-0.5Al-0.1Ca alloy exhibits an ultimate tensile strength of 211 MPa,coupled with a remarkable 41%fracture elongation.

Relationship between the unique microstructures and behaviors of high-entropy alloys

High-entropy alloys(HEAs),which were introduced as a pioneering concept in 2004,have captured the keen interest of nu-merous researchers.Entropy,in this context,can be perceived as representing disorder and randomness.By contrast,elemental composi-tions within alloy systems occupy specific structural sites in space,a concept referred to as structure.In accordance with Shannon entropy,structure is analogous to information.Generally,the arrangement of atoms within a material,termed its structure,plays a pivotal role in dictating its properties.In addition to expanding the array of options for alloy composites,HEAs afford ample opportunities for diverse structural designs.The profound influence of distinct structural features on the exceptional behaviors of alloys is underscored by numer-ous examples.These features include remarkably high fracture strength with excellent ductility,antiballistic capability,exceptional radi-ation resistance,and corrosion resistance.In this paper,we delve into various unique material structures and properties while elucidating the intricate relationship between structure and performance.

Influence of Metalloid Elements on the Magnetic Properties and Anisotropy of FeNi-based Amorphous Alloys

The magnetic properties and anisotropy of amor- phous(Fe_(80)Ni_(20))_(78)Si_xB_(22-x).alloys have been investigated systematically.The maximum permeability,coercive force and remanence have been determined for as-prepared and annealed samples,The results on the technical magnetic properties of this alloy system have been discussed and compared with Masumoto's.

Thermostability and Application of the Copper-based SMA Engineering Component

The influence of thermo cycle times under variant loads and environment temperatures on the properties of Cu-16.4Zn-4Al (Re) SMA component was studied by thermostability experiments on Cu-16.4Zn-4Al SMA with the composition containing corium Re. Tangent rule was applied to determine the transformation temperature from displacement-temperature loop plot by computer in each thermal-cold cycle. The results is as follows the transformation temperature increases and shape memory property decrease with increasing load, which leads the action temperature of component to be abnormal, and the memory property decreases after overheating aging, and the memory property decreases with increasing cycle times, while the decreasing is not obvious and the recovery ratio is higher than 90% in one thousand times. It is due to the addition of corium Re which has the function of grain refinement. Therefore, it is necessary to avoid overloading and overheating in the application of such component. Thus, a kind of thermo valve that works at normal pressure and in the water as working substance was designed to replace complicate original electromechanical system.

Dynamic Kinetics of Methanol Synthesis over a Commercial Copper-Based Catalyst

Adsorption, surface reaction and process dynamics on the surface of a commercial copper-based catalyst for methanol synthesis from CO/CO2/H2 were systematically studied by means of temperature programmed desorption (TPD), temperature programmed surface reaction (TPSR), in-situ Fourier transform-inferred spec-troscopy(FTIR) and stimulus-response techniques. As a part of results, an elementary step sequence was suggested and a group of ordinary differential equations (ODEs) for describing transient conversations relevant to all species on the catalyst surface and in the gas phase in a micro-fixed-bed reactor was derived. The values of the parameters referred to dynamic kinetics were estimated by fitting the solution of the ODEs with the transient response data obtained by the stimulus-response technique with a FTIR analyzer as an on-line detector.

Microstructure and damping properties of LPSO phase dominant Mg-Ni-Y and Mg-Zn-Ni-Y alloys

This work studied the microstructure,mechanical properties and damping properties of Mg_(95.34)Ni_(2)Y_(2.66) and Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloys systematically.The difference in the evolution of the long-period stacked ordered(LPSO)phase in the two alloys during heat treatment was the focus.The morphology of the as-cast Mg_(95.34)Ni_(2)Y_(2.66)presented a disordered network.After heat treatment at 773 K for 2 hours,the eutectic phase was integrated into the matrix,and the LPSO phase maintained the 18R structure.As Zn partially replaced Ni,the crystal grains became rounded in the cast alloy,and lamellar LPSO phases and more solid solution atoms were contained in the matrix after heat treatment of the Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloy.Both Zn and the heat treatment had a significant effect on damping.Obvious dislocation internal friction peaks and grain boundary internal friction peaks were found after temperature-dependent damping of the Mg_(95.34)Ni_(2)Y_(2.66)and Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloys.After heat treatment,the dislocation peak was significantly increased,especially in the alloy Mg_(95.34)Ni_(2)Y_(2).66.The annealed Mg_(95.34)Ni_(2)Y_(2.66)alloy with a rod-shaped LPSO phase exhibited a good damping performance of 0.14 atε=10^(−3),which was due to the difference between the second phase and solid solution atom content.These factors also affected the dynamic modulus of the alloy.The results of this study will help in further development of high-damping magnesium alloys.

Recent innovations in laser additive manufacturing of titanium alloys

Titanium(Ti)alloys are widely used in high-tech fields like aerospace and biomedical engineering.Laser additive manufacturing(LAM),as an innovative technology,is the key driver for the development of Ti alloys.Despite the significant advancements in LAM of Ti alloys,there remain challenges that need further research and development efforts.To recap the potential of LAM high-performance Ti alloy,this article systematically reviews LAM Ti alloys with up-to-date information on process,materials,and properties.Several feasible solutions to advance LAM Ti alloys are reviewed,including intelligent process parameters optimization,LAM process innovation with auxiliary fields and novel Ti alloys customization for LAM.The auxiliary energy fields(e.g.thermal,acoustic,mechanical deformation and magnetic fields)can affect the melt pool dynamics and solidification behaviour during LAM of Ti alloys,altering microstructures and mechanical performances.Different kinds of novel Ti alloys customized for LAM,like peritecticα-Ti,eutectoid(α+β)-Ti,hybrid(α+β)-Ti,isomorphousβ-Ti and eutecticβ-Ti alloys are reviewed in detail.Furthermore,machine learning in accelerating the LAM process optimization and new materials development is also outlooked.This review summarizes the material properties and performance envelops and benchmarks the research achievements in LAM of Ti alloys.In addition,the perspectives and further trends in LAM of Ti alloys are also highlighted.

Model Calculation of ln γ_i^0 for Solute Elements in Copper-base Alloy Systems

A calculation formula of ln γ i 0 for solute element i in liquid alloys was derived by use of free volume theory and Miedema formation enthalpy model. The values of ln γ i 0 of solute elements in liquid copper at 1273 K were obtained. The results obtained show that the coincidence rate of sign (positive or negative) was 90% for the calculated and experimental values, which were basically in the same magnitude.

Microstructures,corrosion behavior and mechanical properties of as-cast Mg-6Zn-2X(Fe/Cu/Ni)alloys for plugging tool applications

Mg-6Zn-2X(Fe/Cu/Ni)alloys were prepared through semi-continuous casting,with the aim of identifying a degradable magnesium(Mg)alloy suitable for use in fracturing balls.A comparative analysis was conducted to assess the impacts of adding Cu and Ni,which result in finer grains and the formation of galvanic corrosion sites.Scanner electronic microscopy examination revealed that precipitated phases concentrated at grain boundaries,forming a semi-continuous network structure that facilitated corrosion penetration in Mg-6Zn-2Cu and Mg-6Zn-2Ni alloys.Pitting corrosion was observed in Mg-6Zn-2Fe,while galvanic corrosion was identified as the primary mechanism in Mg-6Zn-2Cu and Mg-6Zn-2Ni alloys.Among the tests,the Mg-6Zn-2Ni alloy exhibited the highest corrosion rate(approximately 932.9 mm/a)due to its significant potential difference.Mechanical testing showed that Mg-6Zn-2Ni alloy possessed suitable ultimate compressive strength,making it a potential candidate material for degradable fracturing balls,effectively addressing the challenges of balancing strength and degradation rate in fracturing applications.