The detection of hypersonic targets usually confronts range migration(RM)issue before coherent integration(CI).The traditional methods aiming at correcting RM to obtain CI mainly considers the narrow-band radar condit...The detection of hypersonic targets usually confronts range migration(RM)issue before coherent integration(CI).The traditional methods aiming at correcting RM to obtain CI mainly considers the narrow-band radar condition.However,with the increasing requirement of far-range detection,the time bandwidth product,which is corresponding to radar’s mean power,should be promoted in actual application.Thus,the echo signal generates the scale effect(SE)at large time bandwidth product situation,influencing the intra and inter pulse integration performance.To eliminate SE and correct RM,this paper proposes an effective algorithm,i.e.,scaled location rotation transform(ScLRT).The ScLRT can remove SE to obtain the matching pulse compression(PC)as well as correct RM to complete CI via the location rotation transform,being implemented by seeking the actual rotation angle.Compared to the traditional coherent detection algorithms,Sc LRT can address the SE problem to achieve better detection/estimation capabilities.At last,this paper gives several simulations to assess the viability of ScLRT.展开更多
BACKGROUND Mandibular retraction is the main etiological mechanism of class II malocclusion in China and the subsequent distal molar relationship can cause functional discomfort in mastication,breathing and the tempor...BACKGROUND Mandibular retraction is the main etiological mechanism of class II malocclusion in China and the subsequent distal molar relationship can cause functional discomfort in mastication,breathing and the temporomandibular joint.The use of mandibular advancement(MA)devices has recently emerged as an adolescent mandibular retraction treatment;however,current studies regarding the effect thereof are relatively few,and there is lack of sufficient clinical support.AIM To investigate the clinical effect of invisalign MA on the treatment of mandibular retraction in adolescents.METHODS This study included 30 adolescent patients who underwent treatment with the MA appliances from December 2017 to June 2021.The lateral cephalometric data before and after treatment were collected and imported into Dolphin Imaging software.The changes were measured by linear measurement superimposed with lateral cephalometric trajectory based on the Pancherz technology.RESULTS There was no significant difference in the length and position of maxilla before and after the treatment.The position of the mandible moved 3.13 mm,the length increased 4.14 mm,the mandibular ramus length increased 4.09 mm,the body length increased 4.25 mm,and the position of the condyle moved 1.03 mm forward after treatment.Additionally,changes in the incisor sagittal position and labial inclination were observed.The position of the upper incisor point moved back 1.33 mm,without statistical difference,the inclination and tooth angle decreased by 3.44°and 4.06°,respectively;the position of the lower incisor point was moved 2.98 mm,and the inclination and tooth angle increased by 2.62°and 1.23°,respectively.Furthermore,changes in the incisor overjet and molar relationship were seen.Overjet decreased by 4.31 mm,of which 1.78 mm was due to dental factors,accounting for 41.3%of the effect as opposed to 58.7%due to skeletal factors.Molar relationship improved 3.87 mm,with 1.34 mm due to dental factors,and dental and skeletal factors were accounted for 34.6%and 65.4%of the effect,respectively.CONCLUSION For adolescent patients with mandible retraction,invisalign MA can effectively promote the mandible growth,and it was proven to be mainly due to skeletal effects.展开更多
Due to improper acquisition settings and other noise artifacts,the image degraded to yield poor mean preservation in brightness.The simplest way to improve the preservation is the implementation of histogram equalizat...Due to improper acquisition settings and other noise artifacts,the image degraded to yield poor mean preservation in brightness.The simplest way to improve the preservation is the implementation of histogram equalization.Because of over-enhancement,it failed to preserve the mean brightness and produce the poor quality of the image.This paper proposes a multi-scale decomposi-tion for brightness preservation using gamma correction.After transformation to hue,saturation and intensity(HSI)channel,the 2D-discrete wavelet transform decomposed the intensity component into low and high-pass coefficients.At the next phase,gamma correction is used by auto-tuning the scale value.The scale is the modified constant value used in the logarithmic function.Further,the scale value is optimized to obtain better visual quality in the image.The optimized value is the weighted distribution of standard deviation-mean of low pass coefficients.Finally,the experimental result is estimated in terms of quality assessment measures used as absolute mean brightness error,the measure of information detail,signal to noise ratio and patch-based contrast quality in the image.By comparison,the proposed method proved to be suitably remarkable in retaining the mean brightness and better visual quality of the image.展开更多
The space satellite programs, such as CZCS/Nimbus - 7, VHRSR/FY - 1, OCFS/ ADEOS and SeaWiFS/SeaStar, have demonstrated and proven that remote sensing is a powerful tool for understanding the spatial and temporal ocea...The space satellite programs, such as CZCS/Nimbus - 7, VHRSR/FY - 1, OCFS/ ADEOS and SeaWiFS/SeaStar, have demonstrated and proven that remote sensing is a powerful tool for understanding the spatial and temporal ocean color distribution. In general, there are two main techni-cal keys in the processing ocean color satellite data. They are the atmospheric correction and the inver-sion of water-leaving radiance into water constituents (such as chlorophyll, suspended material and yel low substance) quantitatively. The SeaWiFS (sea-viewing wide field-of-view sensor) atmospheric correc-tion algorithm for China's coastal waters is discussed. First, the major advantages of SeaWiFS are introduced. Second, in view of the problems of the SeaDAS algorithm applying in China' s coastal waters, the local atmospheric correction algorithms are discussed and developed. Finally, the advantages of the local algorithms are presented by the compari-son of the results from two different algorithms.展开更多
Vertical errors often present in multibeam swath bathymetric data. They are mainly sourced by sound refraction, internal wave disturbance, imperfect tide correction, transducer mounting, long period heave, static draf...Vertical errors often present in multibeam swath bathymetric data. They are mainly sourced by sound refraction, internal wave disturbance, imperfect tide correction, transducer mounting, long period heave, static draft change, dynamic squat and dynamic motion residuals, etc. Although they can be partly removed or reduced by specific algorithms, the synthesized depth biases are unavoidable and sometimes have an important influence on high precise utilization of the final bathymetric data. In order to. confidently identify the decimeter-level changes in seabed morphology by MBES, we must remove or weaken depth biases and improve the precision of multibeam bathymetry further. The fixed-interval profiles that are perpendicular to the vessel track are generated to adjust depth biases between swaths. We present a kind of postprocessing method to minimize the depth biases by the histogram of cumulative depth biases. The datum line in each profile can be obtained by the maximum value of histogram. The corrections of depth biases can be calculated according to the datum line. And then the quality of final bathymetry can be improved by the corrections. The method is verified by a field test.展开更多
High resolution Fresnel zone plates for nanoscale three-dimensional imaging of materials by both soft and hard x-rays are increasingly needed by the broad applications in nanoscience and nanotechnology.When the outmos...High resolution Fresnel zone plates for nanoscale three-dimensional imaging of materials by both soft and hard x-rays are increasingly needed by the broad applications in nanoscience and nanotechnology.When the outmost zone-width is shrinking down to 50 nm or even below,patterning the zone plates with high aspect ratio by electron beam lithography still remains a challenge because of the proximity effect.The uneven charge distribution in the exposed resist is still frequently observed even after standard proximity effect correction(PEC),because of the large variety in the line width.This work develops a new strategy,nicknamed as local proximity effect correction(LPEC),efficiently modifying the deposited energy over the whole zone plate on the top of proximity effect correction.By this way,50 nm zone plates with the aspect ratio from 4:1 up to 15:1 and the duty cycle close to 0.5 have been fabricated.Their imaging capability in soft(1.3 keV)and hard(9 keV)x-ray,respectively,has been demonstrated in Shanghai Synchrotron Radiation Facility(SSRF)with the resolution of 50 nm.The local proximity effect correction developed in this work should also be generally significant for the generation of zone plates with high resolutions beyond 50 nm.展开更多
Controllable D-D neutron sources have a long service life,low cost,and non-radioactivity.There are favorable prospects for its application in geophysical well logging,since traditional chemical radioactive sources use...Controllable D-D neutron sources have a long service life,low cost,and non-radioactivity.There are favorable prospects for its application in geophysical well logging,since traditional chemical radioactive sources used for well logging pose potential threats to the safety of the human body and environment.This paper presents an improved method to measure formation density that employs a D-D neutron source.In addition,the lithological effect on the measured density was removed to better estimate the formation porosity.First,we investigated the spatial distribution of capture gamma rays through Monte Carlo simulations as well as the relationship between the ratio of capture gamma ray counts and formation density to establish theoretical support for the design of density logging tools and their corresponding data processing methods.Second,we obtained the far to near detector counts of captured gamma rays for an optimized tool structure and then established its correlation with the density and porosity of three typical formations with pure quartz,calcite,and dolomite minerals.Third,we determined the values for correcting the densities of sandstone and dolomite with the same porosity using limestone data as the reference and established the equations for calculating the correction values,which lays a solid foundation for accurately calculating formation porosity.We observed that the capture gamma ray counts first increased then decreased and varied in different formations;this was especially observed in high-porosity formations.Under the same lithologic conditions(rock matrix),as the porosity increases,the peak value of gamma ray counts moves toward the neutron source.At different detector-source distances,the ratio of the capture gamma ray counts was well correlated with the formation density.An equation of the formation density conversion was established based on the ratio of capture gamma ray counts at the detector-source distances of 30 cm and 65 cm,and the calculated values were consistent with the true values.After correction,the formation density was highly consistent with the true value of the limestone density,and the mean absolute error was 0.013 g/cm3.The calculated porosity values were very close to the true values,and the mean relative error was 2.33%,highlighting the accuracy of the proposed method.These findings provide a new method for developing D-D neutron source logging tools and their well-log data processing methods.展开更多
Systems using numerous cameras are emerging in many fields due to their ease of production and reduced cost, and one of the fields where they are expected to be used more actively in the near future is in image-based ...Systems using numerous cameras are emerging in many fields due to their ease of production and reduced cost, and one of the fields where they are expected to be used more actively in the near future is in image-based rendering (IBR). Color correction between views is necessary to use multi-view systems in IBR to make audiences feel comfortable when views are switched or when a free viewpoint video is displayed. Color correction usually involves two steps: the first is to adjust camera parameters such as gain, brightness, and aperture before capture, and the second is to modify captured videos through image processing. This paper deals with the latter, which does not need a color pattern board. The proposed method uses scale invariant feature transform (SIFT) to detect correspondences, treats RGB channels independently, calculates lookup tables with an energy-minimization approach, and corrects captured video with these tables. The experimental results reveal that this approach works well.展开更多
A third-order correction was recently suggested to improve the accuracy of the half-power bandwidth method in estimating the damping of single DOF systems.This paper analyzes the accuracy of the half-power bandwidth m...A third-order correction was recently suggested to improve the accuracy of the half-power bandwidth method in estimating the damping of single DOF systems.This paper analyzes the accuracy of the half-power bandwidth method with the third-order correction in damping estimation for multi-DOF linear systems.Damping ratios in a two-DOF linear system are estimated using its displacement and acceleration frequency response curves,respectively.A wide range of important parameters that characterize the shape of these response curves are taken into account.Results show that the third-order correction may greatly improve the accuracy of the half-power bandwidth method in estimating damping in a two-DOF system.In spite of this,the half-power bandwidth method may significantly overestimate the damping ratios of two-DOF systems in some cases.展开更多
Research works on width compensation and correction were carried out in order to eliminate the effects of the PVPC( plan view pattern control) on width accuracy of plate mill. The thickness correction calculation form...Research works on width compensation and correction were carried out in order to eliminate the effects of the PVPC( plan view pattern control) on width accuracy of plate mill. The thickness correction calculation formula was derived for compensation the width deviation caused by PVPC function,and the formula is unified under the thinning and thickening conditions. In order to improve the width calculation accuracy, width spread calculation process was modified with dividing one large reduction pass to several small reduction calculation steps. The thickness wedge was simplified to rectangle based on the volume constant principle,and the width spread model for PVPC was constructed. The width compensation and correction for the PVPC functions are used for the online control process,and the Product dimension accuracy is improved. With the decrease of crop losses,the product yield was increased with 0. 2%.展开更多
The blind-hole method is the most widely used approach to experimentally determine the distribution of residual stress. This paper aims to improve test accuracy of welding residual stress and conducts an experimental ...The blind-hole method is the most widely used approach to experimentally determine the distribution of residual stress. This paper aims to improve test accuracy of welding residual stress and conducts an experimental study on the strain release factors involved when using the blind-hole method for Q235 and Q345, two steels commonly used in building structures. The ranges of strain release factors A and B in the elastic stage, the effects of strain release factors on residual stress calculated values, and the plastic corrected strain release factors are analyzed considering of the effect of plastic deformation around the blind hole on measurement accuracy. Finally, a simplified calculation formula to determine strain release factors is proposed for use with the blind-hole method. Results show that in the elastic stage, strain release factor A for Q235 and Q345 ranges from-0.399 to-0.525 and strain release factor B from-0.791 to-0.960. Changing the strain release factors A and B shows that calculated residual tensile stress varies in relation to a decrease in both factor values. However, there is a increase in calculated residual compressive stress with a decrease in the strain release factor A value, but there is an decrease with a decrease in strain release factor B value. Calculated residual stress applied to elastic strain release factors is compared with that applied to amended plastic strain release factors for Q235 steel. The maximum deviation between calculated residual stress and test stress is reduced from 21.1 to 1.0%,and for Q345 steel from 26.5 to 1.2%. It is thus evident that the plastic correction formula proposed in this paper can be used in calculations when conducting a residual stress test.展开更多
A novel method,referred to as joint multiple subpulses processing,is developed to calibrate the nonideal transfer function of radio frequency front-end and I/Q imbalance in quadrature modulate/demodulate systems simul...A novel method,referred to as joint multiple subpulses processing,is developed to calibrate the nonideal transfer function of radio frequency front-end and I/Q imbalance in quadrature modulate/demodulate systems simultaneously,which frequently occur in wideband Synthetic Aperture Radar(SAR) systems.Based on the time-frequency relation of the chirp signal and the analyses of the channel errors in wideband SAR,joint multiple subpulses processing method is adopted to separate the image frequency component due to the I/Q channel error.Then,the complete description of the channel error is acquired for building the correction function,which is used to correct the radar raw echo in frequency domain.The validity and capability of this method are demonstrated by the experiments of the channel error correction on the high resolution SAR system with the effective bandwidth of 500 MHz.展开更多
The subtle color distinction is the important function of electronic endoscope imaging diagnosis.However,after image acquisition,transmission and display,color distortions of intracorporeal organs or tissues occur ine...The subtle color distinction is the important function of electronic endoscope imaging diagnosis.However,after image acquisition,transmission and display,color distortions of intracorporeal organs or tissues occur inevitably,which are adverse to analyze image features accurately or to diagnose early pathological changes.A real-time color correction algorithm based on fourneighborhood and polynomial regression in YUV color space is proposed.Based on polynomial regression the color correction matrix is calculated in YUV color space according to the dierences between standard values of color checker and measured values of that imaged by the endoscope.As the correction is only executed on U and V components in YUV color space,the defect that the color of corrected images in RGB color space will change along with luminance can be avoided,and then the stability of image color is improved.Owing to four-neighborhood processing,the signal-to-noise ratio of corrected images is enhanced and the processing speed of correction algorithm is accelerated.The average color dierence is reduced from 0.3944 to 0.2850 by application of the proposed algorithm in high-denition electronic endoscope.A total of 17 frames per second can be achieved at the resolution of 1280800,and the color characteristics of the image after processing match that of human visual system.展开更多
Unbalance existing in the mechanical systems is one of the most common causes which leads to unexpected vibration,nonsmooth motions,uncertain dynamics and even instability. In this paper,the problem of unbalance ident...Unbalance existing in the mechanical systems is one of the most common causes which leads to unexpected vibration,nonsmooth motions,uncertain dynamics and even instability. In this paper,the problem of unbalance identification and correction is investigated for the countershaft system of a precision centrifuge with two degrees of freedom. According to the characteristics of the load under test installed on the countershaft,a gradual subdivision algorithm is proposed to identify the phase of the unbalance,and its amplitude is calculated by using a space vector algorithm,where the vibration information of the mainshaft system is obtained by utilizing two axis-layout displacement transducers installed associated to the mainshaft.Based on ADAMS software,some numerical simulations are presented and compared,and further,the validity of the strategy is demonstrated by experimental examples.展开更多
AIM:To evaluate the refractive correction for standard automated perimetry(SAP)in eyes with refractive multifocal contact lenses(CL)in healthy young participants.METHODS:Twenty-nine eyes of 29 participants were ...AIM:To evaluate the refractive correction for standard automated perimetry(SAP)in eyes with refractive multifocal contact lenses(CL)in healthy young participants.METHODS:Twenty-nine eyes of 29 participants were included.Accommodation was paralyzed in all participants with 1%cyclopentolate hydrochloride.SAP was performed using the Humphrey SITA-standard 24-2 and 10-2 protocol under three refractive conditions:monofocal CL corrected for near distance(baseline);multifocal CL corrected for distance(m CL-D);and m CL-D corrected for near vision using a spectacle lens(m CL-N).Primary outcome measures were the foveal threshold,mean deviation(MD),and pattern standard deviation(PSD).RESULTS:The foveal threshold of m CL-N with both the24-2 and 10-2 protocols significantly decreased by 2.2-2.5 d B(P〈0.001),while that of m CL-D with the 24-2 protocol significantly decreased by 1.5 d B(P=0.0427),as compared with that of baseline.Although there was no significant difference between the MD of baseline and m CL-D with the24-2 and 10-2 protocols,the MD of m CL-N was significantly decreased by 1.0-1.3 d B(P〈0.001)as compared with that of both baseline and m CL-D,with both 24-2 and 10-2 protocols.There was no significant difference in the PSD among the three refractive conditions with both the 24-2 and 10-2 protocols.CONCLUSION:Despite the induced mydriasis and the optical design of the multifocal lens used in this study,our results indicated that,when the dome-shaped visual field test is performed with eyes with large pupils and wearing refractive multifocal CLs,distance correction without additional near correction is to be recommended.展开更多
Baseline offset in digital strong-motion acceleration record and initial velocity can produce unrealistic results for ground velocity and displacement derived from the acceleration by integration. A new method is prop...Baseline offset in digital strong-motion acceleration record and initial velocity can produce unrealistic results for ground velocity and displacement derived from the acceleration by integration. A new method is proposed for the baseline correction and initial velocity calculation. It is based on linear least-squares fitting of the pre-event portion of velocity derived from the uncorrected acceleration data. Compared with the conventional method,which is based on removing the mean values of the pre-event portions of the acceleration and velocity traces,this method has clearer physical meaning and better stability.展开更多
A simplified surface correction formulation is proposed to diminish the far-field spurious sound generated by the quadrupole source term in Ffowcs Williams and Hawkings(FW-H)integrals.The proposed formulation utilizes...A simplified surface correction formulation is proposed to diminish the far-field spurious sound generated by the quadrupole source term in Ffowcs Williams and Hawkings(FW-H)integrals.The proposed formulation utilizes the far-field asymptotics of the Green’s function to simplify the computation of its high-order derivatives,which circumvents the difficulties reported in the original frequency-domain surface correction formulation.The proposed formulation has been validated by investigating the benchmark case of sound generated by a convecting vortex.The results show that the proposed formulation successfully eliminates the spurious sound.The applications of the proposed formulation to flows with some special parameters are also discussed.展开更多
Let two separate surveys collect related information on a single population U. Consider situation where we want to best combine data from the two surveys to yield a single set of estimates of a population quantity (po...Let two separate surveys collect related information on a single population U. Consider situation where we want to best combine data from the two surveys to yield a single set of estimates of a population quantity (population parameter) of interest. This Article presents a multiplicative bias reduction estimator for nonparametric regression to two sample problem in sample survey. The approach consists to apply a multiplicative bias correction to an estimator. The multiplicative bias correction method which was proposed, by Linton & Nielsen, 1994, assures a positive estimate and reduces the bias of the estimate with negligible increase in variance. Even as we apply this method to the two sample problem in sample survey, we found out through the study of it asymptotic properties that it was asymptotically unbiased, and statistically consistent. Furthermore an empirical study was carried out to compare the performance of the developed estimator with the existing ones.展开更多
As an open-loop model predictive control algorithm,finite control set model predictive control(FCS-MPC)scheme in power converter system is based on assumption that responses of optimal control implemented on predictio...As an open-loop model predictive control algorithm,finite control set model predictive control(FCS-MPC)scheme in power converter system is based on assumption that responses of optimal control implemented on prediction model agree well with actual system.The influence of model parameter mismatches and environment disturbance on control performance of scheme is neglected.Then,based on feedback correction strategy in traditional model predictive control algorithm,we derive a finite control set model predictive control with feedback correction scheme(FCS-MPCFC)that allows us to adjust prediction model output at current instant by model prediction error at previous instant,and the closed-loop correction of prediction model output is achieved.Simulations comparison analyses on a two-level three-phase inverter with multi-type model parameter mismatches controlled by traditional and improved FCS-MPC scheme are presented.Experiments are carried out on DSP controller platform.展开更多
In order to understand the effect of hardening ductility parameters and softening ductility parameters of the concrete damage plastic model in LS-DYNA,a sensitivity and reliability analysis of these parameters through...In order to understand the effect of hardening ductility parameters and softening ductility parameters of the concrete damage plastic model in LS-DYNA,a sensitivity and reliability analysis of these parameters through a convenient cube unit test was conducted. The results showed that the peak strength strain was independent of the hardening ductility parameter DH,but affected by AH,BH,and CH. The softening ductility was mainly related to the softening ductility parameter AS,but not affected by the damage ductility exponent BS. In case that the model with default parameters failed to match the AS-controlled damage softening phase,an optimized model with an AS correction was developed. The corrected model with the AS value of 2 matched well with the code model,and exhibited good feasibility in predicting the stress-strain curve of different grades of concrete. Moreover,the practicability of the corrected model was further validated by the conventional triaxial test. The simulated curve exhibited favorable consistence with the trial curve. Therefore,the model with parameter correction could provide a prospective reference for predicting the mechanical properties of concrete.展开更多
基金supported by the National Natural Science Foundation of China(62101099)the Chinese Postdoctoral Science Foundation(2021M690558,2022T150100,2018M633352,2019T120825)+3 种基金the Young Elite Scientist Sponsorship Program(YESS20200082)the Aeronautical Science Foundation of China(2022Z017080001)the Open Foundation of Science and Technology on Electronic Information Control Laboratorythe Natural Science Foundation of Sichuan Province(2023NSFSC1386)。
文摘The detection of hypersonic targets usually confronts range migration(RM)issue before coherent integration(CI).The traditional methods aiming at correcting RM to obtain CI mainly considers the narrow-band radar condition.However,with the increasing requirement of far-range detection,the time bandwidth product,which is corresponding to radar’s mean power,should be promoted in actual application.Thus,the echo signal generates the scale effect(SE)at large time bandwidth product situation,influencing the intra and inter pulse integration performance.To eliminate SE and correct RM,this paper proposes an effective algorithm,i.e.,scaled location rotation transform(ScLRT).The ScLRT can remove SE to obtain the matching pulse compression(PC)as well as correct RM to complete CI via the location rotation transform,being implemented by seeking the actual rotation angle.Compared to the traditional coherent detection algorithms,Sc LRT can address the SE problem to achieve better detection/estimation capabilities.At last,this paper gives several simulations to assess the viability of ScLRT.
基金This study was reviewed and approved by the Medical Ethics Committee of The Affiliated Hospital of Qingdao University(authorisation number:QYFYWZLL26729).
文摘BACKGROUND Mandibular retraction is the main etiological mechanism of class II malocclusion in China and the subsequent distal molar relationship can cause functional discomfort in mastication,breathing and the temporomandibular joint.The use of mandibular advancement(MA)devices has recently emerged as an adolescent mandibular retraction treatment;however,current studies regarding the effect thereof are relatively few,and there is lack of sufficient clinical support.AIM To investigate the clinical effect of invisalign MA on the treatment of mandibular retraction in adolescents.METHODS This study included 30 adolescent patients who underwent treatment with the MA appliances from December 2017 to June 2021.The lateral cephalometric data before and after treatment were collected and imported into Dolphin Imaging software.The changes were measured by linear measurement superimposed with lateral cephalometric trajectory based on the Pancherz technology.RESULTS There was no significant difference in the length and position of maxilla before and after the treatment.The position of the mandible moved 3.13 mm,the length increased 4.14 mm,the mandibular ramus length increased 4.09 mm,the body length increased 4.25 mm,and the position of the condyle moved 1.03 mm forward after treatment.Additionally,changes in the incisor sagittal position and labial inclination were observed.The position of the upper incisor point moved back 1.33 mm,without statistical difference,the inclination and tooth angle decreased by 3.44°and 4.06°,respectively;the position of the lower incisor point was moved 2.98 mm,and the inclination and tooth angle increased by 2.62°and 1.23°,respectively.Furthermore,changes in the incisor overjet and molar relationship were seen.Overjet decreased by 4.31 mm,of which 1.78 mm was due to dental factors,accounting for 41.3%of the effect as opposed to 58.7%due to skeletal factors.Molar relationship improved 3.87 mm,with 1.34 mm due to dental factors,and dental and skeletal factors were accounted for 34.6%and 65.4%of the effect,respectively.CONCLUSION For adolescent patients with mandible retraction,invisalign MA can effectively promote the mandible growth,and it was proven to be mainly due to skeletal effects.
文摘Due to improper acquisition settings and other noise artifacts,the image degraded to yield poor mean preservation in brightness.The simplest way to improve the preservation is the implementation of histogram equalization.Because of over-enhancement,it failed to preserve the mean brightness and produce the poor quality of the image.This paper proposes a multi-scale decomposi-tion for brightness preservation using gamma correction.After transformation to hue,saturation and intensity(HSI)channel,the 2D-discrete wavelet transform decomposed the intensity component into low and high-pass coefficients.At the next phase,gamma correction is used by auto-tuning the scale value.The scale is the modified constant value used in the logarithmic function.Further,the scale value is optimized to obtain better visual quality in the image.The optimized value is the weighted distribution of standard deviation-mean of low pass coefficients.Finally,the experimental result is estimated in terms of quality assessment measures used as absolute mean brightness error,the measure of information detail,signal to noise ratio and patch-based contrast quality in the image.By comparison,the proposed method proved to be suitably remarkable in retaining the mean brightness and better visual quality of the image.
文摘The space satellite programs, such as CZCS/Nimbus - 7, VHRSR/FY - 1, OCFS/ ADEOS and SeaWiFS/SeaStar, have demonstrated and proven that remote sensing is a powerful tool for understanding the spatial and temporal ocean color distribution. In general, there are two main techni-cal keys in the processing ocean color satellite data. They are the atmospheric correction and the inver-sion of water-leaving radiance into water constituents (such as chlorophyll, suspended material and yel low substance) quantitatively. The SeaWiFS (sea-viewing wide field-of-view sensor) atmospheric correc-tion algorithm for China's coastal waters is discussed. First, the major advantages of SeaWiFS are introduced. Second, in view of the problems of the SeaDAS algorithm applying in China' s coastal waters, the local atmospheric correction algorithms are discussed and developed. Finally, the advantages of the local algorithms are presented by the compari-son of the results from two different algorithms.
基金supported by the project of Shandong Provincial National Science Foundation for Distinguished Young Scholars(Grant No.JQ201113)SDUST's National Science Foundation for Distinguished Young Scholars(Grant No.2010KYJQ102)
文摘Vertical errors often present in multibeam swath bathymetric data. They are mainly sourced by sound refraction, internal wave disturbance, imperfect tide correction, transducer mounting, long period heave, static draft change, dynamic squat and dynamic motion residuals, etc. Although they can be partly removed or reduced by specific algorithms, the synthesized depth biases are unavoidable and sometimes have an important influence on high precise utilization of the final bathymetric data. In order to. confidently identify the decimeter-level changes in seabed morphology by MBES, we must remove or weaken depth biases and improve the precision of multibeam bathymetry further. The fixed-interval profiles that are perpendicular to the vessel track are generated to adjust depth biases between swaths. We present a kind of postprocessing method to minimize the depth biases by the histogram of cumulative depth biases. The datum line in each profile can be obtained by the maximum value of histogram. The corrections of depth biases can be calculated according to the datum line. And then the quality of final bathymetry can be improved by the corrections. The method is verified by a field test.
基金Project supported by the National Natural Science Foundation of China(Grant No.U1732104)China Postdoctoral Science Foundation(Grant No.2017M611443)Shanghai STCSM2019-11-20 Grant,China(Grant No.19142202700)。
文摘High resolution Fresnel zone plates for nanoscale three-dimensional imaging of materials by both soft and hard x-rays are increasingly needed by the broad applications in nanoscience and nanotechnology.When the outmost zone-width is shrinking down to 50 nm or even below,patterning the zone plates with high aspect ratio by electron beam lithography still remains a challenge because of the proximity effect.The uneven charge distribution in the exposed resist is still frequently observed even after standard proximity effect correction(PEC),because of the large variety in the line width.This work develops a new strategy,nicknamed as local proximity effect correction(LPEC),efficiently modifying the deposited energy over the whole zone plate on the top of proximity effect correction.By this way,50 nm zone plates with the aspect ratio from 4:1 up to 15:1 and the duty cycle close to 0.5 have been fabricated.Their imaging capability in soft(1.3 keV)and hard(9 keV)x-ray,respectively,has been demonstrated in Shanghai Synchrotron Radiation Facility(SSRF)with the resolution of 50 nm.The local proximity effect correction developed in this work should also be generally significant for the generation of zone plates with high resolutions beyond 50 nm.
基金supported by the National Natural Science Foundation of China(Nos.41704113,41674129)Key R&D Projects in Shandong Province(No.2019GSF109047)+1 种基金China Postdoctoral Science Foundation Grant(No.2019M661912)Science and Technology Plan Project of Shandong Education of China(Nos.J18KA190 and J18KA128)。
文摘Controllable D-D neutron sources have a long service life,low cost,and non-radioactivity.There are favorable prospects for its application in geophysical well logging,since traditional chemical radioactive sources used for well logging pose potential threats to the safety of the human body and environment.This paper presents an improved method to measure formation density that employs a D-D neutron source.In addition,the lithological effect on the measured density was removed to better estimate the formation porosity.First,we investigated the spatial distribution of capture gamma rays through Monte Carlo simulations as well as the relationship between the ratio of capture gamma ray counts and formation density to establish theoretical support for the design of density logging tools and their corresponding data processing methods.Second,we obtained the far to near detector counts of captured gamma rays for an optimized tool structure and then established its correlation with the density and porosity of three typical formations with pure quartz,calcite,and dolomite minerals.Third,we determined the values for correcting the densities of sandstone and dolomite with the same porosity using limestone data as the reference and established the equations for calculating the correction values,which lays a solid foundation for accurately calculating formation porosity.We observed that the capture gamma ray counts first increased then decreased and varied in different formations;this was especially observed in high-porosity formations.Under the same lithologic conditions(rock matrix),as the porosity increases,the peak value of gamma ray counts moves toward the neutron source.At different detector-source distances,the ratio of the capture gamma ray counts was well correlated with the formation density.An equation of the formation density conversion was established based on the ratio of capture gamma ray counts at the detector-source distances of 30 cm and 65 cm,and the calculated values were consistent with the true values.After correction,the formation density was highly consistent with the true value of the limestone density,and the mean absolute error was 0.013 g/cm3.The calculated porosity values were very close to the true values,and the mean relative error was 2.33%,highlighting the accuracy of the proposed method.These findings provide a new method for developing D-D neutron source logging tools and their well-log data processing methods.
文摘Systems using numerous cameras are emerging in many fields due to their ease of production and reduced cost, and one of the fields where they are expected to be used more actively in the near future is in image-based rendering (IBR). Color correction between views is necessary to use multi-view systems in IBR to make audiences feel comfortable when views are switched or when a free viewpoint video is displayed. Color correction usually involves two steps: the first is to adjust camera parameters such as gain, brightness, and aperture before capture, and the second is to modify captured videos through image processing. This paper deals with the latter, which does not need a color pattern board. The proposed method uses scale invariant feature transform (SIFT) to detect correspondences, treats RGB channels independently, calculates lookup tables with an energy-minimization approach, and corrects captured video with these tables. The experimental results reveal that this approach works well.
基金National Natural Science Foundation under Grant No. 51179093National Basic Research Program of China under Grant No. 2011CB013602Program for New Century Excellent Talents in University under Grant No.NCET-10-0531
文摘A third-order correction was recently suggested to improve the accuracy of the half-power bandwidth method in estimating the damping of single DOF systems.This paper analyzes the accuracy of the half-power bandwidth method with the third-order correction in damping estimation for multi-DOF linear systems.Damping ratios in a two-DOF linear system are estimated using its displacement and acceleration frequency response curves,respectively.A wide range of important parameters that characterize the shape of these response curves are taken into account.Results show that the third-order correction may greatly improve the accuracy of the half-power bandwidth method in estimating damping in a two-DOF system.In spite of this,the half-power bandwidth method may significantly overestimate the damping ratios of two-DOF systems in some cases.
基金Sponsored by the Fundamental Research Funds for the Central Universities(Grant No.N120407007)
文摘Research works on width compensation and correction were carried out in order to eliminate the effects of the PVPC( plan view pattern control) on width accuracy of plate mill. The thickness correction calculation formula was derived for compensation the width deviation caused by PVPC function,and the formula is unified under the thinning and thickening conditions. In order to improve the width calculation accuracy, width spread calculation process was modified with dividing one large reduction pass to several small reduction calculation steps. The thickness wedge was simplified to rectangle based on the volume constant principle,and the width spread model for PVPC was constructed. The width compensation and correction for the PVPC functions are used for the online control process,and the Product dimension accuracy is improved. With the decrease of crop losses,the product yield was increased with 0. 2%.
基金supported by the National Natural Science Foundation of China (no. 51478120)
文摘The blind-hole method is the most widely used approach to experimentally determine the distribution of residual stress. This paper aims to improve test accuracy of welding residual stress and conducts an experimental study on the strain release factors involved when using the blind-hole method for Q235 and Q345, two steels commonly used in building structures. The ranges of strain release factors A and B in the elastic stage, the effects of strain release factors on residual stress calculated values, and the plastic corrected strain release factors are analyzed considering of the effect of plastic deformation around the blind hole on measurement accuracy. Finally, a simplified calculation formula to determine strain release factors is proposed for use with the blind-hole method. Results show that in the elastic stage, strain release factor A for Q235 and Q345 ranges from-0.399 to-0.525 and strain release factor B from-0.791 to-0.960. Changing the strain release factors A and B shows that calculated residual tensile stress varies in relation to a decrease in both factor values. However, there is a increase in calculated residual compressive stress with a decrease in the strain release factor A value, but there is an decrease with a decrease in strain release factor B value. Calculated residual stress applied to elastic strain release factors is compared with that applied to amended plastic strain release factors for Q235 steel. The maximum deviation between calculated residual stress and test stress is reduced from 21.1 to 1.0%,and for Q345 steel from 26.5 to 1.2%. It is thus evident that the plastic correction formula proposed in this paper can be used in calculations when conducting a residual stress test.
基金Supported by the National High-Tech Research and Development Plan of China(No.2007AA120302)
文摘A novel method,referred to as joint multiple subpulses processing,is developed to calibrate the nonideal transfer function of radio frequency front-end and I/Q imbalance in quadrature modulate/demodulate systems simultaneously,which frequently occur in wideband Synthetic Aperture Radar(SAR) systems.Based on the time-frequency relation of the chirp signal and the analyses of the channel errors in wideband SAR,joint multiple subpulses processing method is adopted to separate the image frequency component due to the I/Q channel error.Then,the complete description of the channel error is acquired for building the correction function,which is used to correct the radar raw echo in frequency domain.The validity and capability of this method are demonstrated by the experiments of the channel error correction on the high resolution SAR system with the effective bandwidth of 500 MHz.
基金supported by grants from National Key Technology R&D Program(Grant No.:2011BAI12B06)the Fundamental Research Funds for the Central Universities(Grant No.:2012FZA5023).
文摘The subtle color distinction is the important function of electronic endoscope imaging diagnosis.However,after image acquisition,transmission and display,color distortions of intracorporeal organs or tissues occur inevitably,which are adverse to analyze image features accurately or to diagnose early pathological changes.A real-time color correction algorithm based on fourneighborhood and polynomial regression in YUV color space is proposed.Based on polynomial regression the color correction matrix is calculated in YUV color space according to the dierences between standard values of color checker and measured values of that imaged by the endoscope.As the correction is only executed on U and V components in YUV color space,the defect that the color of corrected images in RGB color space will change along with luminance can be avoided,and then the stability of image color is improved.Owing to four-neighborhood processing,the signal-to-noise ratio of corrected images is enhanced and the processing speed of correction algorithm is accelerated.The average color dierence is reduced from 0.3944 to 0.2850 by application of the proposed algorithm in high-denition electronic endoscope.A total of 17 frames per second can be achieved at the resolution of 1280800,and the color characteristics of the image after processing match that of human visual system.
基金Sponsored by the National Natural Science Foundation of China(Grant Nos.61203191 and 61427809)the China Postdoctoral Science Foundation(Grant No.2015M571415)+1 种基金the Heilongjiang Postdoctoral Foundation(Grant No.LBH-Z14088)the Fundamental Research Funds for the Central Universities(Grant No.HIT.NSRIF.201626)
文摘Unbalance existing in the mechanical systems is one of the most common causes which leads to unexpected vibration,nonsmooth motions,uncertain dynamics and even instability. In this paper,the problem of unbalance identification and correction is investigated for the countershaft system of a precision centrifuge with two degrees of freedom. According to the characteristics of the load under test installed on the countershaft,a gradual subdivision algorithm is proposed to identify the phase of the unbalance,and its amplitude is calculated by using a space vector algorithm,where the vibration information of the mainshaft system is obtained by utilizing two axis-layout displacement transducers installed associated to the mainshaft.Based on ADAMS software,some numerical simulations are presented and compared,and further,the validity of the strategy is demonstrated by experimental examples.
基金Supported by School of Allied Health Sciences,Kitasato University,Kanagawa,Japan
文摘AIM:To evaluate the refractive correction for standard automated perimetry(SAP)in eyes with refractive multifocal contact lenses(CL)in healthy young participants.METHODS:Twenty-nine eyes of 29 participants were included.Accommodation was paralyzed in all participants with 1%cyclopentolate hydrochloride.SAP was performed using the Humphrey SITA-standard 24-2 and 10-2 protocol under three refractive conditions:monofocal CL corrected for near distance(baseline);multifocal CL corrected for distance(m CL-D);and m CL-D corrected for near vision using a spectacle lens(m CL-N).Primary outcome measures were the foveal threshold,mean deviation(MD),and pattern standard deviation(PSD).RESULTS:The foveal threshold of m CL-N with both the24-2 and 10-2 protocols significantly decreased by 2.2-2.5 d B(P〈0.001),while that of m CL-D with the 24-2 protocol significantly decreased by 1.5 d B(P=0.0427),as compared with that of baseline.Although there was no significant difference between the MD of baseline and m CL-D with the24-2 and 10-2 protocols,the MD of m CL-N was significantly decreased by 1.0-1.3 d B(P〈0.001)as compared with that of both baseline and m CL-D,with both 24-2 and 10-2 protocols.There was no significant difference in the PSD among the three refractive conditions with both the 24-2 and 10-2 protocols.CONCLUSION:Despite the induced mydriasis and the optical design of the multifocal lens used in this study,our results indicated that,when the dome-shaped visual field test is performed with eyes with large pupils and wearing refractive multifocal CLs,distance correction without additional near correction is to be recommended.
基金supported by the National Natural Science Foundation of China( 41004020)the Director Foundation of Institute of Seismology,CEA(IS200926044)
文摘Baseline offset in digital strong-motion acceleration record and initial velocity can produce unrealistic results for ground velocity and displacement derived from the acceleration by integration. A new method is proposed for the baseline correction and initial velocity calculation. It is based on linear least-squares fitting of the pre-event portion of velocity derived from the uncorrected acceleration data. Compared with the conventional method,which is based on removing the mean values of the pre-event portions of the acceleration and velocity traces,this method has clearer physical meaning and better stability.
基金This work was supported by the National Natural Science Foundation of China Basic Science Center Program for"Multiscale Problems in Nonlinear Mechanics"(Grant 11988102)the National Natural Science Foundation of China(Grants 11922214 and 91952301)the National Numerical Windtunnel project.
文摘A simplified surface correction formulation is proposed to diminish the far-field spurious sound generated by the quadrupole source term in Ffowcs Williams and Hawkings(FW-H)integrals.The proposed formulation utilizes the far-field asymptotics of the Green’s function to simplify the computation of its high-order derivatives,which circumvents the difficulties reported in the original frequency-domain surface correction formulation.The proposed formulation has been validated by investigating the benchmark case of sound generated by a convecting vortex.The results show that the proposed formulation successfully eliminates the spurious sound.The applications of the proposed formulation to flows with some special parameters are also discussed.
文摘Let two separate surveys collect related information on a single population U. Consider situation where we want to best combine data from the two surveys to yield a single set of estimates of a population quantity (population parameter) of interest. This Article presents a multiplicative bias reduction estimator for nonparametric regression to two sample problem in sample survey. The approach consists to apply a multiplicative bias correction to an estimator. The multiplicative bias correction method which was proposed, by Linton & Nielsen, 1994, assures a positive estimate and reduces the bias of the estimate with negligible increase in variance. Even as we apply this method to the two sample problem in sample survey, we found out through the study of it asymptotic properties that it was asymptotically unbiased, and statistically consistent. Furthermore an empirical study was carried out to compare the performance of the developed estimator with the existing ones.
基金This work was supported in part by the Natural Science Foundation of Hunan Province,China under Grant 2015JJ6070。
文摘As an open-loop model predictive control algorithm,finite control set model predictive control(FCS-MPC)scheme in power converter system is based on assumption that responses of optimal control implemented on prediction model agree well with actual system.The influence of model parameter mismatches and environment disturbance on control performance of scheme is neglected.Then,based on feedback correction strategy in traditional model predictive control algorithm,we derive a finite control set model predictive control with feedback correction scheme(FCS-MPCFC)that allows us to adjust prediction model output at current instant by model prediction error at previous instant,and the closed-loop correction of prediction model output is achieved.Simulations comparison analyses on a two-level three-phase inverter with multi-type model parameter mismatches controlled by traditional and improved FCS-MPC scheme are presented.Experiments are carried out on DSP controller platform.
基金Supported by the National Natural Science Foundation of China(10272109)
文摘In order to understand the effect of hardening ductility parameters and softening ductility parameters of the concrete damage plastic model in LS-DYNA,a sensitivity and reliability analysis of these parameters through a convenient cube unit test was conducted. The results showed that the peak strength strain was independent of the hardening ductility parameter DH,but affected by AH,BH,and CH. The softening ductility was mainly related to the softening ductility parameter AS,but not affected by the damage ductility exponent BS. In case that the model with default parameters failed to match the AS-controlled damage softening phase,an optimized model with an AS correction was developed. The corrected model with the AS value of 2 matched well with the code model,and exhibited good feasibility in predicting the stress-strain curve of different grades of concrete. Moreover,the practicability of the corrected model was further validated by the conventional triaxial test. The simulated curve exhibited favorable consistence with the trial curve. Therefore,the model with parameter correction could provide a prospective reference for predicting the mechanical properties of concrete.