Methacrylic acid was used together with a molecular imprinting technique to modify chitosan. In addition, the adsorption kinetics and adsorption isotherms were recorded and the results were analyzed to investigate rep...Methacrylic acid was used together with a molecular imprinting technique to modify chitosan. In addition, the adsorption kinetics and adsorption isotherms were recorded and the results were analyzed to investigate reparative adsorption for Cr（VI） from the polluted Xiangjiang River water. A comparative X-ray analysis shows that the degree of crystallization in the imprinted polymer was significantly weakened, the area of the non-crystalline region was larger. There were more adsorption sites in the imprinted polymer, and the adsorption capacity towards Cr（VI） was increased. The adsorption capacity of the imprinted polymer towards Cr（VI） increased with time and reaches saturation after 8 h. The optimal adsorption time was 4-8 h after the adsorption starting and the optimal pH value for the solution was in the range of 4.5-7.5. When the chitosan reaches saturation, the adsorption capacity achieves a state of equilibrium, and the maximum Cr（VI） extraction rate reaches 33.7%. Moreover, the adsorption capacity of the imprinted polymer towards Cr（VI） increases with increasing chitosan concentration. In this situation, the Cr（VI） extraction rate shows little variation, and the maximum removal rate can reach 98.3%. Furthermore, the Cr（VI） extraction rate increases with an increase in the degree of deacetylation in the chatoyant and chitosan, with the best adsorption effect corresponding to 90% deacetylation. Fitting the adsorption data to the quasi first- and second-order kinetic models yields correlation coefficients of 0.9013 and 0.9875, respectively. The corresponding rate constants for the two models are 0.0091 min-1 and 7.129 g/（mg.min）, respectively. Hence, the adsorption using Cr（VI）-imprinted chitosan is more consistent with the second-order kinetics. Comparing the data to Freundlich and Langrnuir adsorption isotherms shows that the latter has a better linear fit and a maximum adsorption capacity of 15.784 mg/g.展开更多
基金Project(41271332)supported by the National Natural Science Foundation of ChinaProject(2010YBB186)supported by the Social Science Foundation of Hunan Province,Chian
文摘Methacrylic acid was used together with a molecular imprinting technique to modify chitosan. In addition, the adsorption kinetics and adsorption isotherms were recorded and the results were analyzed to investigate reparative adsorption for Cr（VI） from the polluted Xiangjiang River water. A comparative X-ray analysis shows that the degree of crystallization in the imprinted polymer was significantly weakened, the area of the non-crystalline region was larger. There were more adsorption sites in the imprinted polymer, and the adsorption capacity towards Cr（VI） was increased. The adsorption capacity of the imprinted polymer towards Cr（VI） increased with time and reaches saturation after 8 h. The optimal adsorption time was 4-8 h after the adsorption starting and the optimal pH value for the solution was in the range of 4.5-7.5. When the chitosan reaches saturation, the adsorption capacity achieves a state of equilibrium, and the maximum Cr（VI） extraction rate reaches 33.7%. Moreover, the adsorption capacity of the imprinted polymer towards Cr（VI） increases with increasing chitosan concentration. In this situation, the Cr（VI） extraction rate shows little variation, and the maximum removal rate can reach 98.3%. Furthermore, the Cr（VI） extraction rate increases with an increase in the degree of deacetylation in the chatoyant and chitosan, with the best adsorption effect corresponding to 90% deacetylation. Fitting the adsorption data to the quasi first- and second-order kinetic models yields correlation coefficients of 0.9013 and 0.9875, respectively. The corresponding rate constants for the two models are 0.0091 min-1 and 7.129 g/（mg.min）, respectively. Hence, the adsorption using Cr（VI）-imprinted chitosan is more consistent with the second-order kinetics. Comparing the data to Freundlich and Langrnuir adsorption isotherms shows that the latter has a better linear fit and a maximum adsorption capacity of 15.784 mg/g.
