Quaternary carbide Ti3NiAl2C ceramics has been investigated as a potential nuclear fusion structural material,and it has advantages in certain aspects compared with Ti2AlC,Ti3AlC2,and Ti3SiC2 structural materials.In t...Quaternary carbide Ti3NiAl2C ceramics has been investigated as a potential nuclear fusion structural material,and it has advantages in certain aspects compared with Ti2AlC,Ti3AlC2,and Ti3SiC2 structural materials.In this paper,quaternary carbide Ti3NiAl2C ceramics is pressurized to investigate its structural,mechanical,electronic properties,and Debye temperature.Quaternary carbide Ti3NiAl2C ceramics still maintains a cubic structure under pressure(0–110 GPa).At zero pressure,quaternary carbide Ti3NiAl2C ceramics only has three bonds:Ti–Al,Ni–Al,and Ti–C.However,at pressures of 20 GPa,30 GPa,40 GPa,60 GPa,and 70 GPa,new Ti–Ni,Ti–Ti,Al–Al,Ti–Al,and Ti–Ti bonds form.When the pressure reaches 20 GPa,the covalent bonds change to metallic bonds.The volume of quaternary carbide Ti3NiAl2C ceramics can be compressed to 72%of its original volume at most.Pressurization can improve the mechanical strength and ductility of quaternary carbide Ti3NiAl2C ceramics.At 50–60 GPa,its mechanical strength can be comparable to pure tungsten,and the material changes from brittleness to ductility.However,the degree of anisotropy of quaternary carbide Ti3NiAl2C ceramics increases with the increasing pressure.In addition,we also investigated the Debye temperature,density,melting point,hardness,and wear resistance of quaternary carbide Ti3NiAl2C ceramics under pressure.展开更多
With OLYMPUS PMG3 metallograph, an abnormal three-layer gradient structure, i. e. coarse grain zone, binder enrichment zone and normal structure zone from surface to inner, was observed in Cr3C2 based cemented carbide...With OLYMPUS PMG3 metallograph, an abnormal three-layer gradient structure, i. e. coarse grain zone, binder enrichment zone and normal structure zone from surface to inner, was observed in Cr3C2 based cemented carbide. In the binder enrichment zone, three different shapes of anomalous coarse carbides were observed. It is shown that the transverse rupture strength can be raised remarkably, up 20.7%from the alloy with abnormal gradient structure by removing the abnormal gradient structure. The results suggested that the abnormal gradient structure in the surface, especially the anomalous coarse carbides in the binder enrichment zone is the main reason for the lower strength展开更多
利用高温固相反应法制备了新型三元锂离子电池正极材料Li2Ru1/3Co1/3M1/3O3(M=Mn、Ni、Fe)。通过X射线衍射技术和电化学性能测试对Li2Ru1/3Co1/3M1/3O3的微观结构及其电化学性能进行了表征。研究结果表明,Li2Ru1/3Co1/3Ni1/3O3和Li2Ru1/...利用高温固相反应法制备了新型三元锂离子电池正极材料Li2Ru1/3Co1/3M1/3O3(M=Mn、Ni、Fe)。通过X射线衍射技术和电化学性能测试对Li2Ru1/3Co1/3M1/3O3的微观结构及其电化学性能进行了表征。研究结果表明,Li2Ru1/3Co1/3Ni1/3O3和Li2Ru1/3Co1/3Fe1/3O3为六方层状结构,空间群为R-3M,而Li2Ru1/3Co1/3Mn1/3O3保持了单斜结构;电化学性能测试表明Li2Ru1/3Co1/3Mn1/3O3的电化学性能优于掺杂Fe和Ni的三元材料,该材料具有良好的循环性能,在电流密度为16 m A/g情况下,首次充电容量达到190 m Ah/g,首次放电容量为171 m Ah/g,50次循环后容量保持率为98%。展开更多
The excellent optical properties of MXene provide new opportunities for short-pulse lasers. A diode-pumped passively Q-switched laser at 1.3 μm wavelength with MXene Ti3C2Tx as saturable absorber was achieved for the...The excellent optical properties of MXene provide new opportunities for short-pulse lasers. A diode-pumped passively Q-switched laser at 1.3 μm wavelength with MXene Ti3C2Tx as saturable absorber was achieved for the first time. The stable passively Q-switched laser has 454 ns pulse width and 162 kHz repetition rate at 4.5 W incident pumped power. The experimental results show that the MXene Ti3C2Tx saturable absorber can be used as an optical modulator to generate short pulse lasers in a solid-state laser field.展开更多
Synthesis of complexes（η;-CH;C;H;）M（CO）;NO（M=Mo,I;M=W,II）and clusters（η;-CH;C;H;）M（μ;-NH）(μ;-NO) （μ;-CO）Fe;（CO）;（M=Mo,III:M=W,IV）,based on the reaction of （η;-C5;）M（CO）;Cl with Na[Fe（CO）;NO...Synthesis of complexes（η;-CH;C;H;）M（CO）;NO（M=Mo,I;M=W,II）and clusters（η;-CH;C;H;）M（μ;-NH）(μ;-NO) （μ;-CO）Fe;（CO）;（M=Mo,III:M=W,IV）,based on the reaction of （η;-C5;）M（CO）;Cl with Na[Fe（CO）;NO] at room tem-perature,have been demonstrated,The crystal structures of II and IV arealso presented.展开更多
Microstructure evolution and properties of hot-extruded Inconel 625 alloy were investigated at different creep temperatures, aging time and strain rates. The experimental results indicate that the Inconel 625 alloy ex...Microstructure evolution and properties of hot-extruded Inconel 625 alloy were investigated at different creep temperatures, aging time and strain rates. The experimental results indicate that the Inconel 625 alloy exhibits an excellent creep resistance at 700 ℃ and below. When the creep temperature rises to 750 ℃, the creep resistance falls drastically due to the failure of phase transformation strengthening and the precipitation of a large amount of δ phase and σ phase at the grain boundary. The special temperature-sensitive characteristics of Inconel 625 alloy play a very important role in its fracture. When the strain rate is 8.33×10^-3s^-1, the strength of the specimen is higher than that of other parameters attributed to the effect of phase transformation strengthening. With the increase of Ni3(Al, Ti), the phase transformation strengthening inhibits thickening of the stacking faults into twins and improves the overall mechanical properties of the alloy. With the increase of the aging time, the granular Cr-rich M23C6 carbides continue to precipitate at the grain boundary, which hinders the movement of the dislocations and obviously increases the strength of the samples. Especially, the yield strength increases several times.展开更多
One new Iriterpene saponin was isolated from Panaxjaponicus C. A. Meyer var major （Burk.） C. Y. Wu et K. M. Feng, and established as oleanolic acid 3-O-[β-D-glucopyranosyl-（1 →2）-β-D-glucuronopyranosyl-6＇-O-n-...One new Iriterpene saponin was isolated from Panaxjaponicus C. A. Meyer var major （Burk.） C. Y. Wu et K. M. Feng, and established as oleanolic acid 3-O-[β-D-glucopyranosyl-（1 →2）-β-D-glucuronopyranosyl-6＇-O-n-butyl ester] which showed mod- erate antitumor activities against the A2780 cells and OVCAR-3 cells. Its structure was established by means of spectral data, particularly NMR, including HSQC and HMBC techniques.展开更多
The morphology,microstructure and decomposition behavior of M2C carbides in high speed steels with different chemical compositions have been investigated by scanning electron microscopy,transmission electron microscop...The morphology,microstructure and decomposition behavior of M2C carbides in high speed steels with different chemical compositions have been investigated by scanning electron microscopy,transmission electron microscopy,electron backscatter diffraction and X-ray diffraction.The results show that the morphology and substructure of M2C carbides are very sensitive to chemical compositions of high speed steels.M2C carbides present the plate-like shape in tungsten-molybdenum steel and present the polycrystal orientation in the eutectic cell.In contrast,they show the fibrous shape in molybdenum-base steel and exhibit the monocrystal orientation.Plate-like and fibrous M2C carbides are both metastable and decompose into M6 C together with MC at high temperatures.MC nucleates inside the plate-like M2C while it is formed at the fibrous M2C/matrix interface during the decomposition process.Such differences are expected to arise from different compositions of plate-like and fibrous M2C carbides.展开更多
以氨基-1,2,4-三唑和2-偕二硝甲基-5-硝基四唑(HDNMNT)为原料,通过中和反应合成出两种新型含能离子盐——2-偕二硝甲基-5-硝基四唑3-氨基-1,2,4-三唑盐(3-ATDNMNT)和2-偕二硝甲基-5-硝基四唑4-氨基-1,2,4-三唑盐(4-ATDNMNT),收率分别为9...以氨基-1,2,4-三唑和2-偕二硝甲基-5-硝基四唑(HDNMNT)为原料,通过中和反应合成出两种新型含能离子盐——2-偕二硝甲基-5-硝基四唑3-氨基-1,2,4-三唑盐(3-ATDNMNT)和2-偕二硝甲基-5-硝基四唑4-氨基-1,2,4-三唑盐(4-ATDNMNT),收率分别为95.4%和96.7%;利用FT-IR、1 H NMR、13C NMR、15 N NMR及元素分析等方法对其结构进行表征;采用量子化学方法计算了3-ATDNMNT和4-ATDNMNT的爆轰性能;在标准状态下(膨胀比为70∶1),利用最小自由能原理,分别计算了两种离子盐在丁羟复合推进剂中的能量性能。结果表明,3-ATDNMNT的爆速和爆压分别为8.587km/s和33.58GPa,4-ATDNMNT的爆速和爆压分别为8.693km/s和34.31GPa。以3-ATDNMNT部分取代丁羟复合推进剂中的AP后,丁羟复合推进剂的理论比冲可达2 635.7N·s/kg。以4-ATDNMNT部分取代丁羟复合推进剂中的AP后,当HTPB、Al、AP及4-ATDNMNT各组分质量分数分别为10%、5%、15%及70%时,获得该丁羟复合推进剂的最高理论比冲为2 677.2N·s/kg。展开更多
基金Project supported by Fujian Science&Technology Innovation Laboratory for Energy Devices of China(21C-LAB)(Grant No.21C-OP-202013)the National Natural Science Foundation of China(Grant No.12064027)+1 种基金the International Science and Technology Cooperation Program of China(Grant No.2015DFA61800)the Scientific Research Fund of Jiangxi Provincial Education Department,China(Grant No.GJJ180973).
文摘Quaternary carbide Ti3NiAl2C ceramics has been investigated as a potential nuclear fusion structural material,and it has advantages in certain aspects compared with Ti2AlC,Ti3AlC2,and Ti3SiC2 structural materials.In this paper,quaternary carbide Ti3NiAl2C ceramics is pressurized to investigate its structural,mechanical,electronic properties,and Debye temperature.Quaternary carbide Ti3NiAl2C ceramics still maintains a cubic structure under pressure(0–110 GPa).At zero pressure,quaternary carbide Ti3NiAl2C ceramics only has three bonds:Ti–Al,Ni–Al,and Ti–C.However,at pressures of 20 GPa,30 GPa,40 GPa,60 GPa,and 70 GPa,new Ti–Ni,Ti–Ti,Al–Al,Ti–Al,and Ti–Ti bonds form.When the pressure reaches 20 GPa,the covalent bonds change to metallic bonds.The volume of quaternary carbide Ti3NiAl2C ceramics can be compressed to 72%of its original volume at most.Pressurization can improve the mechanical strength and ductility of quaternary carbide Ti3NiAl2C ceramics.At 50–60 GPa,its mechanical strength can be comparable to pure tungsten,and the material changes from brittleness to ductility.However,the degree of anisotropy of quaternary carbide Ti3NiAl2C ceramics increases with the increasing pressure.In addition,we also investigated the Debye temperature,density,melting point,hardness,and wear resistance of quaternary carbide Ti3NiAl2C ceramics under pressure.
文摘With OLYMPUS PMG3 metallograph, an abnormal three-layer gradient structure, i. e. coarse grain zone, binder enrichment zone and normal structure zone from surface to inner, was observed in Cr3C2 based cemented carbide. In the binder enrichment zone, three different shapes of anomalous coarse carbides were observed. It is shown that the transverse rupture strength can be raised remarkably, up 20.7%from the alloy with abnormal gradient structure by removing the abnormal gradient structure. The results suggested that the abnormal gradient structure in the surface, especially the anomalous coarse carbides in the binder enrichment zone is the main reason for the lower strength
文摘利用高温固相反应法制备了新型三元锂离子电池正极材料Li2Ru1/3Co1/3M1/3O3(M=Mn、Ni、Fe)。通过X射线衍射技术和电化学性能测试对Li2Ru1/3Co1/3M1/3O3的微观结构及其电化学性能进行了表征。研究结果表明,Li2Ru1/3Co1/3Ni1/3O3和Li2Ru1/3Co1/3Fe1/3O3为六方层状结构,空间群为R-3M,而Li2Ru1/3Co1/3Mn1/3O3保持了单斜结构;电化学性能测试表明Li2Ru1/3Co1/3Mn1/3O3的电化学性能优于掺杂Fe和Ni的三元材料,该材料具有良好的循环性能,在电流密度为16 m A/g情况下,首次充电容量达到190 m Ah/g,首次放电容量为171 m Ah/g,50次循环后容量保持率为98%。
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61475089 and 61435010)the Science and Technology Planning Project of Guangdong Province,China(Grant No.2016B050501005)the Science and Technology Innovation Commission of Shenzhen,China(Grant No.KQTD2015032416270385)
文摘The excellent optical properties of MXene provide new opportunities for short-pulse lasers. A diode-pumped passively Q-switched laser at 1.3 μm wavelength with MXene Ti3C2Tx as saturable absorber was achieved for the first time. The stable passively Q-switched laser has 454 ns pulse width and 162 kHz repetition rate at 4.5 W incident pumped power. The experimental results show that the MXene Ti3C2Tx saturable absorber can be used as an optical modulator to generate short pulse lasers in a solid-state laser field.
文摘Synthesis of complexes（η;-CH;C;H;）M（CO）;NO（M=Mo,I;M=W,II）and clusters（η;-CH;C;H;）M（μ;-NH）(μ;-NO) （μ;-CO）Fe;（CO）;（M=Mo,III:M=W,IV）,based on the reaction of （η;-C5;）M（CO）;Cl with Na[Fe（CO）;NO] at room tem-perature,have been demonstrated,The crystal structures of II and IV arealso presented.
基金Funded by the National Natural Science Foundation of China(Nos.51664041,51561021,and 51665032)in part by Longyuan Youth Innovation and Entrepreneurship ProjectsBRICS STI Framework Programme
文摘Microstructure evolution and properties of hot-extruded Inconel 625 alloy were investigated at different creep temperatures, aging time and strain rates. The experimental results indicate that the Inconel 625 alloy exhibits an excellent creep resistance at 700 ℃ and below. When the creep temperature rises to 750 ℃, the creep resistance falls drastically due to the failure of phase transformation strengthening and the precipitation of a large amount of δ phase and σ phase at the grain boundary. The special temperature-sensitive characteristics of Inconel 625 alloy play a very important role in its fracture. When the strain rate is 8.33×10^-3s^-1, the strength of the specimen is higher than that of other parameters attributed to the effect of phase transformation strengthening. With the increase of Ni3(Al, Ti), the phase transformation strengthening inhibits thickening of the stacking faults into twins and improves the overall mechanical properties of the alloy. With the increase of the aging time, the granular Cr-rich M23C6 carbides continue to precipitate at the grain boundary, which hinders the movement of the dislocations and obviously increases the strength of the samples. Especially, the yield strength increases several times.
基金financially supported by Chinese Academy of Nutritional Sciences,Shanghai Institutes for Biological Sciences
文摘One new Iriterpene saponin was isolated from Panaxjaponicus C. A. Meyer var major （Burk.） C. Y. Wu et K. M. Feng, and established as oleanolic acid 3-O-[β-D-glucopyranosyl-（1 →2）-β-D-glucuronopyranosyl-6＇-O-n-butyl ester] which showed mod- erate antitumor activities against the A2780 cells and OVCAR-3 cells. Its structure was established by means of spectral data, particularly NMR, including HSQC and HMBC techniques.
基金funded by National Natural Science Foundation of China(51301038,51371050)Industry-Academia-Research Program of Jiangsu Province of China(BY2014127-03)+2 种基金Natural Science Foundation of Jiangsu Province of China(BK20141306)Key Research Program of Jiangsu Province of China(BE2016154)Jiangsu Province Key Laboratory of High-end Structural Materials of China(hsm1404)
文摘The morphology,microstructure and decomposition behavior of M2C carbides in high speed steels with different chemical compositions have been investigated by scanning electron microscopy,transmission electron microscopy,electron backscatter diffraction and X-ray diffraction.The results show that the morphology and substructure of M2C carbides are very sensitive to chemical compositions of high speed steels.M2C carbides present the plate-like shape in tungsten-molybdenum steel and present the polycrystal orientation in the eutectic cell.In contrast,they show the fibrous shape in molybdenum-base steel and exhibit the monocrystal orientation.Plate-like and fibrous M2C carbides are both metastable and decompose into M6 C together with MC at high temperatures.MC nucleates inside the plate-like M2C while it is formed at the fibrous M2C/matrix interface during the decomposition process.Such differences are expected to arise from different compositions of plate-like and fibrous M2C carbides.
文摘以氨基-1,2,4-三唑和2-偕二硝甲基-5-硝基四唑(HDNMNT)为原料,通过中和反应合成出两种新型含能离子盐——2-偕二硝甲基-5-硝基四唑3-氨基-1,2,4-三唑盐(3-ATDNMNT)和2-偕二硝甲基-5-硝基四唑4-氨基-1,2,4-三唑盐(4-ATDNMNT),收率分别为95.4%和96.7%;利用FT-IR、1 H NMR、13C NMR、15 N NMR及元素分析等方法对其结构进行表征;采用量子化学方法计算了3-ATDNMNT和4-ATDNMNT的爆轰性能;在标准状态下(膨胀比为70∶1),利用最小自由能原理,分别计算了两种离子盐在丁羟复合推进剂中的能量性能。结果表明,3-ATDNMNT的爆速和爆压分别为8.587km/s和33.58GPa,4-ATDNMNT的爆速和爆压分别为8.693km/s和34.31GPa。以3-ATDNMNT部分取代丁羟复合推进剂中的AP后,丁羟复合推进剂的理论比冲可达2 635.7N·s/kg。以4-ATDNMNT部分取代丁羟复合推进剂中的AP后,当HTPB、Al、AP及4-ATDNMNT各组分质量分数分别为10%、5%、15%及70%时,获得该丁羟复合推进剂的最高理论比冲为2 677.2N·s/kg。
