Preparation and Performance of Organically Modified Montmorillonite Composite Separation Membrane

A new composite separation membrane was developed by using organically modified montmorillonite(OMMT)as an additive.The effects of OMMT on the modification and properties of PVDF composite membranes were investigated.It is found that different kinds and amounts of OMMT into the casting solution can obviously change the pure water flux,separation performance and hydrophilicity of composite membrane in varying degrees.When the TA/PDA-MMT was 0.5 wt%,the pure water flux of the membrane reached the maximum,which was 584.7 L/(m^(2)·h),about 6 times that of the original membrane.The OMMT/PVDF composite membrane had good hydrophilicity and stability in the treatment of oily wastewater.The development of novel OMMT/PVDF composite membrane will provide a new idea for solving the problem of oily wastewater treatment.

Layer-by-layer fabrication of montmorillonite coating immobilizing Cu_(2)O nanoparticles for continuously catalyzing glycerol to dihydroxyacetone

Microreactors are increasingly used for green and safe chemical processes owing to their benefits of superior mass and heat transfer,increased yield,safety,and simplicity of control.However,immobilizing catalysts in microreactors remains challenging.In this investigation,a technique for creating Cu_(2)O/montmorillonite catalyst coating,using electrostatic attraction for layer-by-layer self-assembly,was proposed.The montmorillonite film's morphology and thickness could be efficiently regulated by adjusting the degree of exfoliation and surface charge of montmorillonite,alongside layer-by-layer coating times.The Cu_(2)O nanoparticles were immobilized using the flow deposition approach.The resulting Cu_(2)O@montmorillonite-film-coated capillary microreactor successfully transformed glycerol into dihydroxyacetone.The conversion of glycerol and product selectivity could be controlled by adjusting the molar ratio of reactants,temperature,residence time,and Cu_(2)O loading.The maximum glycerol conversion observed was 47.6%,with a 27%selectivity toward dihydroxyacetone.The study presents a technique for immobilizing montmorillonite-based catalyst coatings in capillary tubing,which can serve as a foundation for the future application of microreactors in glycerol conversion.

Vertically aligned montmorillonite aerogel-encapsulated polyethylene glycol with directional heat transfer paths for efficient solar thermal energy harvesting and storage

The conversion and storage of photothermal energy using phase change materials(PCMs)represent an optimal approach for harnessing clean and sustainable solar energy.Herein,we encapsulated polyethylene glycol(PEG)in montmorillonite aerogels(3D-Mt)through vacuum impregnation to prepare 3D-Mt/PEG composite PCMs.When used as a support matrix,3D-Mt can effectively prevent PEG leakage and act as a flame-retardant barrier to reduce the flammability of PEG.Simultaneously,3D-Mt/PEG demonstrates outstanding shape retention,increased thermal energy storage density,and commendable thermal and chemical stability.The phase transition enthalpy of 3D-Mt/PEG can reach 167.53 J/g and remains stable even after 50 heating-cooling cycles.Furthermore,the vertical sheet-like structure of 3D-Mt establishes directional heat transport channels,facilitating efficient phonon transfer.This configuration results in highly anisotropic thermal conductivities that ensure swift thermal responses and efficient heat conduction.This study addresses the shortcomings of PCMs,including the issues of leakage and inadequate flame retardancy.It achieves the development and design of 3D-Mt/PEG with ultrahigh strength,superior flame retardancy,and directional heat transfer.Therefore,this work offers a design strategy for the preparation of high-performance composite PCMs.The 3D-Mt/PEG with vertically aligned and well-ordered array structure developed in this research shows great potential for thermal management and photothermal conversion applications.

Early changes in corneal densitometry after FS-LASIK combined with accelerated corneal cross-linking for correction of high myopia

AIM:To observe the effects of femtosecond laserassisted excimer laser in situ keratomileusis combined with accelerated corneal cross-linking(FS-LASIK Xtra)on corneal densitometry after correcting for high myopia.METHODS:In this prospectively study,130 patients underwent FS-LASIK or FS-LASIK Xtra for high myopia.Their right eyes were selected for inclusion in the study,of which 65 cases of 65 eyes in the FS-LASIK group,65 patients with 65 eyes in the FS-LASIK Xtra group.Patients were evaluated for corneal densitometry at 1,3,and 6mo postoperatively using Pentacam Scheimpflug imaging.RESULTS:Preoperative differences in corneal densitometry between the FS-LASIK and FS-LASIK Xtra groups in different ranges were not statistically significant(P>0.05).Layer-by-layer analysis revealed statistically significant differences in the anterior(120μm),central,and total layer corneal densitometry between the FS-LASIK and FS-LASIK Xtra groups at 1 and 3mo postoperatively(all P<0.05),the FS-LASIK Xtra group is higher than that of the FS-LASIK group.Analysis of different diameter ranges showed statistically significant differences between the FS-LASIK group and the FS-LASIK Xtra group at 1mo postoperatively in the ranges of 0–2,2–6,and 6–10 mm(both P<0.05);At 3mo postoperatively,the FS-LASIK Xtra group is higher than that of the FS-LASIK group in the ranges of 0–2 and 2–6 mm(P<0.05).At 6mo postoperatively,there were no statistically significant differences in corneal densitometry between the FS-LASIK group and the FS-LASIK Xtra group in different diameter ranges(all P>0.05).CONCLUSION:There is an increase in internal corneal densitometry during the early postoperative period after FS-LASIK Xtra for correction of high myopia.However,the densitometry values decreased to the level of conventional FS-LASIK at 6mo after surgery,with the most significant changes observed in the superficial central zone.

Construction of all-organic low dielectric polyimide hybrids via synergistic effect between covalent organic framework and cross-linking structure

Polyimide(PI)is a promising electronic packaging material,but it remains challenging to obtain an all-organic PI hybrid film with decreased dielectric constant and loss without modifying the monomer.Herein,a series of allorganic PI hybrid films were successfully prepared by introducing the covalent organic framework(COF),which could induce the formation of the cross-linking structure in the PI matrix.Due to the synergistic effects of the COF fillers and the cross-linking structure,the PI/COF hybrid film containing 2 wt%COF exhibited the lowest dielectric constant of 2.72 and the lowest dielectric loss(tanδ)of 0.0077 at 1 MHz.It is attributed to the intrinsic low dielectric constant of COF and a large number of mesopores within the PI.Besides,the cross-linking network of PI prevents the molecular chains from stacking and improves the fraction of free volume(FFV).The molecular dynamics simulation results are well consistent with the dielectric properties data.Furthermore,the PI/COF hybrid film with 5 wt%COF showed a significant enhancement in breakdown strength,which increased to 412.8 kV/mm as compared with pure PI.In addition,the PI/COF hybrid film achieve to reduce the dielectric constant and thermal expansion coefficient(CTE).It also exhibited excellent thermal,hydrophobicity,and mechanical performance.The all-organic PI/COF hybrid films have great commercial potential as next-generation electronic packaging materials.

Cross-Linking of Sago Starch with Furan and Bismaleimide via the Diels-Alder Reaction

This research paper describes the synthesis of thermo-reversible cross-linking of sago starch by grafting a furan pendant group(methyl 2-furoate)onto the starch backbone,followed by a Diels-Alder(DA)reaction of the furan functional group with 1,1′-(methylenedi-4,1-phenylene)bismaleimide(BM).The proof of principles was provided by FTIR and 1H-NMR analyses.The relevant FTIR peaks are the carbonyl peak(υC=O sym)at 1721 cm^(−1);the two peaks appeared after DA cross-linking,i.e.,at 1510 cm^(−1)(corresponding toυCH=CH BM aromatic rings,stretching vibrations),and at 1173 cm^(−1)(assigned to cycloadduct(C-O-C,δDA ring))while the^(1)H-NMR result shows evidence for the presence of a furan ring in the starch matrices(in the range ofδ6.3-7.5 ppm).The crosslinked starch product is indeed thermally reversible,as is evident from the appearance of exothermal(DA,temperature range of 50℃-70℃)and endothermal(retro DA,temperature range of 125℃-150℃)transitions in the DSC thermograms.This paper not only proves the thermal reversibility but also demonstrates that the final product properties(chemical,morphology,and thermal stability)can be tuned by varying the annealing temperature,BM intake,and reaction time.

Hydration Characteristics and Mechanical Properties of Cement-Based Materials Modified by Calcined Zeolite and Montmorillonite

Montmorillonite and clinoptilolite zeolite were used as representative materials to prepare calcined clay-cement binary cementitious materials in order to study the effect of calcination treatment on the activation of clay minerals and the activity difference between layered and framed clays in this research.The influence of different calcined clay content(2%,4%,6%,8%,10%)on the fluidity,compressive strength,microstructure,phase change,and hydration heat of cement-based materials were analyzed.The calcined clay improves the fluidity of cement-based materials as compared with the uncalcined group.The addition of calcined montmorillonite(CMT)improves the development of mechanical strength,and the optimal compressive strength reaches 85 MPa at 28 days with 8%CMT.However,the activity of calcined clinoptilolite zeolite(CZL)is weak with few reaction sites,which slightly reduced the mechanical strength as compared to the blank sample.The addition of CMT changes the microscopic morphology of hydration products such as C-S-H and C-A-H,leading to the formation and transformation of ettringite in the early stage.It promotes the gradual polymerization of Si-O bonds into Si-O-Si bonds simultaneously,which accelerates the early hydration process.However,CZL acts mainly as a filling function in the cementitious system.In brief,CMT as an admixture can improve the mechanical properties of cement,but CZL has little effect.This work provides a guideline for the applications of calcined clay in cement,considering the influence of clay type on workability and mechanical strength.

Improving physical properties of poly(vinyl alcohol)/montmorillonite nanocomposite hydrogels via the Hofmeister effect

Hydrogel is a kind of three-dimensional crosslinked polymer material with high moisture content.However,due to the network defects of polymer gels,traditional hydrogels are usually brittle and fragile,which limits their practical applications.Herein,we present a Hofmeister effect-aided facile strategy to prepare high-performance poly(vinyl alcohol)/montmorillonite nanocomposite hydrogels.Layered montmorillonite nanosheets can not only serve as crosslinking agents to enhance the mechanical properties of the hydrogel but also promote the ion conduction.More importantly,based on the Hofmeister effect,the presence of(NH_(4))_(2)SO_(4)can endow nanocomposite hydrogels with excellent mechanical properties by affecting PVA chains'aggregation state and crystallinity.As a result,the as-prepared nanocomposite hydrogels possess unique physical properties,including robust mechanical and electrical properties.The as-prepared hydrogels can be further assembled into a high-performance flexible sensor,which can sensitively detect large-scale and small-scale human activities.The simple design concept of this work is believed to provide a new prospect for developing robust nanocomposite hydrogels and flexible devices in the future.

Mechanism of high Li-ion conductivity in poly(vinylene carbonate)-poly(ethylene oxide)cross-linked network based electrolyte revealed by solid-state NMR

Solid polymer electrolytes(SPEs)have become increasingly important in advanced lithium-ion batteries(LIBs)due to their improved safety and mechanical properties compared to organic liquid electrolytes.Cross-linked polymers have the potential to further improve the mechanical property without trading off Li-ion conductivity.In this study,focusing on a recently developed cross-linked SPE,i.e.,the one based on poly(vinylene carbonate)-poly(ethylene oxide)cross-linked network(PVCN),we used solid-state nuclear magnetic resonance(NMR)techniques to investigate the fundamental interaction between the chain segments and Li ions,as well as the lithium-ion motion.By utilizing homonuclear/heteronuclear correlation,CP(cross-polarization)kinetics,and spin-lattice relaxation experiments,etc.,we revealed the structural characteristics and their relations to lithium-ion mobilities.It is found that the network formation prevents poly(ethylene oxide)chains from crystallization,which could create sufficient space for segmental tumbling and Li-ion co nductio n.As such,the mechanical property is greatly improved with even higher Li-ion mobilities compared to the poly(vinylene carbonate)or poly(ethylene oxide)based SPE analogues.

Residual alkali-evoked cross-linked polymer layer for anti-air-sensitivity LiNi_(0.89)Co_(0.06)Mn_(0.05)O_(2)cathode

High-energy density lithium-ion batteries(LIBs)with layered high-nickel oxide cathodes(LiNi_(x)Co_(y)Mn_(1-x-y)O_(2),x≥0.8)show great promise in consumer electronics and vehicular applications.However,LiNi_(x)Co_(y)Mn_(1-x-y)O_(2)faces challenges related to capacity decay caused by residual alkalis owing to high sensitivity to air.To address this issue,we propose a hazardous substances upcycling method that fundamentally mitigates alkali content and concurrently induces the emergence of an anti-air-sensitive layer on the cathode surface.Through the neutralization of polyacrylic acid(PAA)with residual alkalis and then coupling it with 3-aminopropyl triethoxysilane(KH550),a stable and ion-conductive cross-linked polymer layer is in situ integrated into the LiNi_(0.89)Co_(0.06)Mn_(0.05)O_(2)(NCM)cathode.Our characterization and measurements demonstrate its effectiveness.The NCM material exhibits impressive cycling performance,retaining 88.4%of its capacity after 200 cycles at 5 C and achieving an extraordinary specific capacity of 170.0 mA h g^(-1) at 10 C.Importantly,this layer on the NCM efficiently suppresses unfavorable phase transitions,severe electrolyte degradation,and CO_(2)gas evolution,while maintaining commendable resistance to air exposure.This surface modification strategy shows widespread potential for creating air-stable LiNi_(x)Co_(y)Mn_(1-x-y)O_(2)cathodes,thereby advancing high-performance LIBs.

Tuning the cross-linked structure of basic poly(ionic liquid)to develop an efficient catalyst for the conversion of vinyl carbonate to dimethyl carbonate

Dimethyl carbonate(DMC)is a crucial chemical raw material widely used in organic synthesis,lithiumion battery electrolytes,and various other fields.The current primary industrial process employs a conventional sodium methoxide basic catalyst to produce DMC through the transesterification reaction between vinyl carbonate and methanol.However,the utilization of this catalyst presents several challenges during the process,including equipment corrosion,the generation of solid waste,susceptibility to deactivation,and complexities in separation and recovery.To address these limitations,a series of alkaline poly(ionic liquid)s,i.e.[DVBPIL][PHO],[DVCPIL][PHO],and[TBVPIL][PHO],with different crosslinking degrees and structures,were synthesized through the construction of cross-linked polymeric monomers and functionalization.These poly(ionic liquid)s exhibit cross-linked structures and controllable cationic and anionic characteristics.Research was conducted to investigate the effect of the cross-linking degree and structure on the catalytic performance of transesterification in synthesizing DMC.It was discovered that the appropriate cross-linking degree and structure of the[DVCPIL][PHO]catalyst resulted in a DMC yield of up to 80.6%.Furthermore,this catalyst material exhibited good stability,maintaining its catalytic activity after repeated use five times without significant changes.The results of this study demonstrate the potential for using alkaline poly(ionic liquid)s as a highly efficient and sustainable alternative to traditional catalysts for the transesterification synthesis of DMC.

Study on the Mechanism of Innovative Montmorillonite for Diarrhea Treatment

[Objective] This study aimed to investigate the mechanism of innovative montmorillonite for diarrhea treatment. [Method] Thirty healthy weanling piglets （Duroc x Landrace x Yorkshire） were randomly divided into five groups and fed with basal diet, basal diet ＋ 1 g/kg innovative montmorillonite, basal diet ＋ 3 g/kg innovative montmorillonite, basal diet ＋ 5 g/kg innovative montmorillonite and basal diet ＋ 3 g/kg Bacillus subtilis microecologic agent, respectively. After four weeks, blood samples were collected via precaval vein, to detect the content of TFF3, NO and SOD in serum by ELISA kits. [Result] Compared with blank control group, the content of TFF3, NO and SOD in high-dose innovative montmorillonite group was extremely significantly increased, extremely significantly reduced and significantly in- creased, respectively; the content of TFF3 and NO in middle-dose innovative mont- morillonite group was significantly increased and significantly reduced, respectively. [Conclusion] Innovative montmorillonite may exert beneficial therapeutic actions on diarrhea by increasing TFF3 and SOD levels and decreasing NO level.

Cadmium adsorption in montmorillonite as affected by glyphosate

Behaviors of soil heavy metals are often affected by coexisting herbicides due to their physical and chemical interaction. Effect of glyphosate, an herbicide containing -PO 2- 3 and -COOH groups, on cadmium adsorption in montmorillonite was studied in detail. The results showed that the cadmium adsorption quantity in montmorillonite increased with increasing soil solution pH and cadmium concentration as usual, but decreased with glyphosate, which is due to the formation of a low affinity complex of Cd and glyphosate and decreasing solution pH induced by glyphosate addition. When the equilibrium solution pH was below 6.7, glyphosate has little effect on cadmium adsorption, but when the equilibrium solution pH was above 6.7, glyphosate significantly decreased cadmium adsorption quantity in montmorillonite. In addition, the adding order of Cd and glyphosate also influenced Cd adsorption quantity in montmorillonite.

Extractive oxidative desulfurization of model oil/crude oil using KSF montmorillonite-supported 12-tungstophosphoric acid

12-Tungstophosphoric acid（PW） supported on KSF montmorillonite, PW/KSF, was used as catalyst for deep oxidative desulfurization（ODS） of mixed thiophenic compounds in model oil and crude oil under mild conditions using hydrogen peroxide（H2O2） as an oxidizing agent. A one-factor-at-a-time method was applied for optimizing the parameters such as temperature, reaction time, amount of catalyst, type of extractant and oxidant-tosulfur compounds（S-compounds） molar ratio. The corresponding products can be easily removed from the model oil by using ethanol as the best extractant. The results showed high catalytic activity of PW/KSF in the oxidative removal of dibenzothiophene（DBT） and mixed thiophenic model oil under atmospheric pressure at 75 ℃ in a biphasic system. To investigate the oxidation and adsorption effects of crude oil composition on ODS, the effects of cyclohexene, 1,7-octadiene and o-xylene with different concentrations were studied.

Preparation and Properties of Gelatin-Chitosan/Montmorillonite Drug-loaded Microspheres

A kind of slow release drug-loaded microspheres were prepared with gelatin, chitosan and montmorillonite（MMT） by an emulsification/chemical cross-linking method using glutaraldehyde as cross-linking agent and acyclovir as model drug. The microspheres were characterized by X-ray diffraction （XRD）, Fourier transform infrared （FT-IR） and scanning electron microscopy （SEM）, respectively. The morphology, drug content, encapsulation efficiency and drug-release behavior were investigated with different MMT contents. The experimental results indicated that intercalated microspheres could be prepared, the morphology of microspheres was markedly affected by MMT. The glomeration performance of uncross-linked microspheres was improved because of the physical cross-linking of MMT. Drug content and encapsulation efficiency were decreased when increased the content of MMT, but burst release and the drug release were significantly decreased with the addition of MMT. Effective physical cross-linking could be formed when added MMT, and MMT could reduce the content of toxic chemical cross-linking agents.

Synthesis of ethyl acetate by esterification of acetic acid with ethanol over a heteropolyacid on montmorillonite K10

In present work,liquid phase esterification of acetic acid with ethanol over dodecatungestophosphoric acid （DTPA） supported on K10 montmorillonite was systematically studied and optimization of process parameters was carried out.The 20% m/m DTPA/K10 was found to be the optimum catalyst with 90% acetic acid conversion and 100% ethyl acetate selectivity.The study was also explored to see the feasibility of 20% m/m DTPA/K10 as a catalyst for the alkylation of acetic acid with other alcohols like methanol,iso-propanol and n-butanol.The 20% m/m DTPA/K10 has shown increased activity with the increase in carbon number,at the same alcohol reflux.The results are novel.

PROPERTIES AND MORPHOLOGY OF UNSATURATED POLYESTER/ACRYLATE-TERMINATED POLYURETHANE/ORGANO-MONTMORILLONITE NANOCOMPOSITES

Unsaturated polyester resin （UPR）/acrylate-terminated polyurethane （ATPU）/organo-modified montmorillonite （OMMT） nanocomposites were prepared by the in situ intercalative polymerization method. Samples were prepared by the sequential mixing, i.e. mixture of the ATPU and styrene （S） and OMMT were prepared in the first step; UPR was then added to the pre-intercalates of ATPU/S/OMMT. Results indicate that the mechanical properties and thermal properties of UPR/ATPU/OMMT nanocomposites greatly depend on the amount of ATPU and OMMT. Results show that the addition of ATPU could increase the impact strength of UPR/ATPU composites, but the tensile strength, flexural strength and heat resistance of the materials are obviously decreased. When the weight ratio between UPR, ATPU and OMMT were 82：15：3, the impact strength and heat distortion-temperature of nanocomposite were greatly improved, meanwhile there was little change for other properties of the nanocomposites. The synergistic enhancement effects of ATPU and OMMT on the composites were observed. The structures and morphology of the composites were investigated by X-ray diffraction, scanning electron microscopy and transmission electron microscopy.

DISPERSION AND TENSILE BEHAVIOR OF POLYPROPYLENE/MONTMORILLONITE NANOCOMPOSITES PRODUCED VIA MELT INTERCALATION

Most of the articles on polymer nanocomposites focus on the importance of chemistry used to modify the surface of the clay, usually montmorillonite (MMT), and characterization of the nano-scale structure obtained. The role and importance of processing were also discussed recently. However, few papers concerning the correlation between morphology of MMT and mechanical properties were published. In order to understand. the tensile behavior of PP/Montmorillonite (MMT) nanocomposites better, and to further improve the reinforcement efficiency, we first prepared the PP nanocomposites via direct melt intercalation using conventional twin-screw extrusion. The dispersion and tensile property of the composites were then investigated by SEM, XRD, TEM and a video-controlled tensile set-up. The macroscopic and microscopic dispersion of MMT in PP matrix was verified by XRD and TEM, combined with SEM. The tensile properties were obtained by video-controlled tensile set-up, which gives true stress-strain curve. It was found that a partly intercalated and partly exfoliated structure (also called incomplete exfoliation) existed in the system. Though the tensile strength of PP nanocomposites is not much improved in engineering stress-strain curves, more than 20% increase of true stress was found in a true stress-strain experiment at high true strain, which indicates that only oriented silicate layers can have a big effect on tensile properties: Not only orientation of silicate platelets but also the degree of exfoliation is a key factor to determine the reinforcement efficiency. The reinforcement efficiency of MMT has been discussed based on the 'continuum' Halpin-Tsai equations. A good agreement was found between experimental data and theoretical prediction by changing N value (number of platelets per stack) which corresponding to different state of the dispersion of MMT in PP matrix.

Preparation and Properties of Phenolic Resin/Montmorillonite Intercalation Nanocomposites

Phenolic resin/montmorillonite intercalation composites were prepared by using the methods of pressing intercalation and melt intercalation.Properties and structure of the composites were investigated by using XRD,TG and test of softening point.It is indicated that both the pressing intercalation and melt intercalation can be used to prepare the phenolic resin/organo-montmorillonite intercalation nanocomposites.Compared with phenolic resin,the intercalation nanocomposites have better heat-resistance,higher decomposition temperatures and less thermal weight-loss.However,these two intercalation methods have different effects on the softening point of the intercalation nanocomposites.Pressing intercalation almost does not affect the softening point of the intercalation nanocomposites,while melt intercalation significantly increases the softening point of the intercalation nanocomposites, probably due to the chemical actions happening in the process of melt intercalation.

Photocatalytic remediation ofγ-hexachlorocyclohexane contaminated soils using TiO_2 and montmorillonite composite photocatalyst

TiO2 and montmorillonite composite photocatalysts were prepared and applied in degrading γ-hexachlorocyclohexane （γ-HCH） in soils. After being spiked with γ-HCH, soil samples loaded with the composite photocatalysts were exposed to UV-light irradiation. The results indicated that the photocatalytic activities of the composite photocatalysts varied with the content of TiO2 in the order of 10%〈70%〈50% 〈30%, Moreover, the photocatalytic activity of the composite photocatalysts with TiO2 content 30% was higher than that of the pure P25 with the same mass of TiO2. The strong adsorption capacity of the composite photocatalysts and quantum size effect may contribute to its increased photocatalytic activities. In addition, effect of dosage of composite photocatalysts and soil pH on γ-HCH photodegradation was investigated. Pentachlorocyclohexene, trichlorocyclohexene, and dichlorobenzene were detected as photodegradation intermediates, which were gradually degraded with the photodegradation evolution.