期刊文献+
共找到51篇文章
< 1 2 3 >
每页显示 20 50 100
Utilization of cross-regional interconnector and pumped hydro energy storage for further introduction of solar PV in Japan
1
作者 Shota Ichimura 《Global Energy Interconnection》 2020年第1期69-76,共8页
The amount of solar PV installed capacity has steadily increased to 44.5 GW at the end of FY2017,since the introduction of the Feed in Tariff(FiT)to Japan in 2012.On the other hand,since the first curtailment of solar... The amount of solar PV installed capacity has steadily increased to 44.5 GW at the end of FY2017,since the introduction of the Feed in Tariff(FiT)to Japan in 2012.On the other hand,since the first curtailment of solar PV was conducted on October 13th,2018 in the Kyushu area,the curtailment has been frequently executed including wind power after that.In this study,cross-regional interconnector and pumped hydro energy storage(PHES)are focused on mitigating curtailment.In Japan,there are 9 electric power areas which connected each other by cross-regional interconnectors.According to the historical operation,cross-regional interconnectors were secured as emergency flexible measures,but after the implicit auction was started from October 2018,it is used on merit order.Regarding a PHES in Japan,they have been built with nuclear power plants for several decades.Because the output of nuclear power generation is constant,so the PHES is used to absorb the surplus at nighttime when the demand declines.All nuclear power plants in Japan have been shut down after the accident at the Fukushima Daiichi Nuclear Power Plant following the Great East Japan Earthquake that occurred on March 11th,2011.There are several nuclear power plants that have been restarted(9 reactors,as of August 2019).In this study,the amount of curtailment for solar PV in the Kyushu area is sent to the Chugoku area using the cross-regional interconnector(Kanmon line).Then,the PHES in the Chugoku area is pumping with low price.Because the spot price in the market is low when the curtailment is executed.After that,the PHES is generating at night with high price when the solar PV is not generating.It makes a profit by the deference for the cost of pumping and the revenue of generating by the PHES.As a calculation result,for one week from May 2nd to 8th,2019,a profit becomes 152.2 million JPY(about 1.22 million EUR).For this purpose,it is necessary to raise the operation capacity of the cross-regional interconnector up to the rated capacity with the frequency control function of solar PV instead of the capacity to keep frequency in the event of an accident.This will allow the further introduction of solar PV in Japan. 展开更多
关键词 SOLAR PV cross-regional interconnector PUMPED HYDRO energy storage(PHES) Curtailment
下载PDF
Cross-regional emergency scheduling planning for petroleum based on the supernetwork model 被引量:5
2
作者 Tao Lv Yan Nie +1 位作者 Chun-Ling Wang Jian Gao 《Petroleum Science》 SCIE CAS CSCD 2018年第3期666-679,共14页
Petroleum, the most important energy source in the world, plays an essential role in securing economic development. If a petroleum shortage happens, it will severely disrupt production and life. Cross-regional emergen... Petroleum, the most important energy source in the world, plays an essential role in securing economic development. If a petroleum shortage happens, it will severely disrupt production and life. Cross-regional emergency scheduling can effectively alleviate a petroleum shortage and further enhance the efficiency of the emergency response. Considering the general lack of focus on cross-regional petroleum dispatching management, we propose a three-layer emergency scheduling network for petroleum based on a supernetwork model that can increase the regional emergency correlation by adding a transfer management process. Then, we compare the total demand for petroleum and the emergency costs considered in the petroleum emergency scheduling supernetwork model(the single-region and the cross-region scenarios).The result shows that the cross-regional emergency scheduling pattern can effectively enhance the efficiency of the emergency preparations and reduce the emergency costs in most cases. However, when the vulnerabilities in the crossregional link grow or the regional linkage decreases, the effect of single-regional scheduling is better. In addition, the advantages of the cross-regional emergency scheduling network will be strengthened with an increase in its maximum emergency capability. Nonetheless, this advantage will disappear when the petroleum demand in the crisis layer reaches the maximum emergency response capacity. Finally, according to the comparative analysis simulation among scenarios,certain strategic policy recommendations are suggested to improve the petroleum emergency scheduling ability in regions.These recommendations include strengthening the cross-regional coordination mechanism, increasing the modes of petroleum transportation and enhancing the carrying capacity of regional emergency routes. 展开更多
关键词 Petroleum emergency SUPERNETWORK cross-regional scheduling Scheduling strategy Variational inequality
下载PDF
Analysis of radiation diffusion of COVID-19 driven by social attributes
3
作者 年福忠 杨晓晨 师亚勇 《Chinese Physics B》 SCIE EI CAS CSCD 2024年第1期773-779,共7页
This paper first estimated the infectious capacity of COVID-19 based on the time series evolution data of confirmed cases in multiple countries. Then, a method to infer the cross-regional spread speed of COVID-19 was ... This paper first estimated the infectious capacity of COVID-19 based on the time series evolution data of confirmed cases in multiple countries. Then, a method to infer the cross-regional spread speed of COVID-19 was introduced in this paper, which took the gross domestic product(GDP) of each region as one of the factors that affect the spread speed of COVID-19 and studied the relationship between the GDP and the infection density of each region(China's Mainland, the United States, and EU countries). In addition, the geographic distance between regions was also considered in this method and the effect of geographic distance on the spread speed of COVID-19 was studied. Studies have shown that the probability of mutual infection of these two regions decreases with increasing geographic distance. Therefore, this paper proposed an epidemic disease spread index based on GDP and geographic distance to quantify the spread speed of COVID-19 in a region. The analysis results showed a strong correlation between the epidemic disease spread index in a region and the number of confirmed cases. This finding provides reasonable suggestions for the control of epidemics. Strengthening the control measures in regions with higher epidemic disease spread index can effectively control the spread of epidemics. 展开更多
关键词 COVID-19 basic reproduction number gross domestic product(GDP) geographic distance cross-regional spread
下载PDF
2023年电子电路技术亮点
4
作者 龚永林 《印制电路信息》 2024年第2期1-6,共6页
介绍2023年电子电路行业内的一些重要技术议题,包括设计技术方面的人工智能应用、热管理、设计与制造协作,产品制造方面的超高密度互连(UHDI)板与载板技术,检测与可靠性的变化,以及可持续绿色生产发展等,以期为行业技术发展提供启示。
关键词 电子电路 设计技术 超高密度互连板 可靠性 可持续发展
下载PDF
3μm铜箔CO_(2)激光直接烧靶工艺研究
5
作者 汤龙洲 赵伟 王继纬 《印制电路信息》 2024年第3期32-35,共4页
为满足印制电路板(PCB)线路等级需求,需要采用改进型半加成工艺(mSAP)并使用3μm及以下的附载体极薄铜箔。采用3μmmSAP工艺时,激光钻孔加工使用开窗流程。为保证对位精度,高精度曝光时抓取内层靶标来对位。利用CO_(2)激光加工的积热效... 为满足印制电路板(PCB)线路等级需求,需要采用改进型半加成工艺(mSAP)并使用3μm及以下的附载体极薄铜箔。采用3μmmSAP工艺时,激光钻孔加工使用开窗流程。为保证对位精度,高精度曝光时抓取内层靶标来对位。利用CO_(2)激光加工的积热效应,验证了3μm铜箔CO_(2)激光直接烧靶的可行性,其中烧蚀靶标的激光叠孔设计和激光加工参数是影响烧靶效果的关键因子。通过研究输出了最优的叠孔设计方案和最适合的激光加工参数。结果表明,采用CO_(2)激光直接烧靶加工,凹点靶标和凸点靶标都可以100%满足高精度曝光抓取靶标的需求。 展开更多
关键词 高密度互连印制电路板 改进型半加成法 超薄铜箔 CO_(2)激光 直接烧靶 积热效应
下载PDF
Cost-profit analysis for Japan-Russia and Japan-South Korea interconnectors 被引量:4
6
作者 Seiichiro Kimura Shota Ichimura 《Global Energy Interconnection》 2019年第2期114-121,共8页
This paper describes the results of cost-profit analysis related to interconnectors for Japan-Russia and JapanSouth Korea based on the Asia International Grid Connection Study Group 2^(nd) report. The Group has been e... This paper describes the results of cost-profit analysis related to interconnectors for Japan-Russia and JapanSouth Korea based on the Asia International Grid Connection Study Group 2^(nd) report. The Group has been established in 2016 for conducting research on international electric power networks in Asia from the viewpoint of technology, investment and legal framework. 2^(nd) report of the Group was published in June 2018, examining the profitability of an interconnectors between Japan and neighboring countries. The Group has calculated expected profit from operation of these interconnectors.The Group has categorized interconnector business into four models from the survey of preceding and current business on grids and interconnectors. To clarify profitability, expected internal rate of return(IRR) was calculated for each business model based on estimated investment cost for each route. When interconnector is dedicated to specific power plants or suppliers and electricity can be sold at Japan wholesale market at 2016-2017 price level, positive IRR levels are expected in case that Free on Board(FOB) price lower than 7 JPY/kWh. When the investment will be covered by electricity tariff by final consumers, tariff for consumers will just slightly increase by approximately 0.1 JPY/kWh. 展开更多
关键词 interconnector Cost-profit analysis Internal Rate of RETURN Business model Japan RUSSIA SOUTH Korea
下载PDF
Tandem organic light-emitting diode with a molybdenum tri-oxide thin film interconnector layer 被引量:1
7
作者 路飞平 王倩 周翔 《Chinese Physics B》 SCIE EI CAS CSCD 2013年第3期442-446,共5页
A 10-nm-thick molybdenum tri-oxide(MoO3) thin film was used as the interconnector layer in tandem organic lightemitting devices(OLEDs).The tandem OLEDs with two identical emissive units consisting of N,N-bis(naph... A 10-nm-thick molybdenum tri-oxide(MoO3) thin film was used as the interconnector layer in tandem organic lightemitting devices(OLEDs).The tandem OLEDs with two identical emissive units consisting of N,N-bis(naphthalen-1-yl)N,N-bis(phenyl)-benzidine(NPB) /tris(8-hydroxyquinoline) aluminum(Alq3) exhibited current efficiency-current density characteristics superior to the conventional single-unit devices.At 20 mA/cm2,the current efficiency of the tandem OLEDs using the interconnector layers of MoO3 thin film was about 4.0 cd/A,which is about twice that of the corresponding conventional single-unit device(1.8cd/A).The tandem OLED showed a higher power efficiency than the conventional single-unit device for luminance over 1200cd/m2.The experimental results demonstrated that a MoO3 thin film with a proper thickness can be used as an effective interconnector layer in tandem OLEDs.Such an interconnector layer can be easily fabricated by simple thermal evaporation,greatly simplifying the device processing and fabrication processes required by previously reported interconnector layers.A possible explanation was proposed for the carrier generation of the MoO3 interconnector layer. 展开更多
关键词 tandem organic light-emitting device MoO3 thin film interconnector layer
下载PDF
Study on Rare Earth Interconnector of La_(1 -x)Ca_xCrO_3
8
作者 刘晓梅 吕吉吉 +3 位作者 刘江 裴力 何岗鹰 苏文辉 《Journal of Rare Earths》 SCIE EI CAS CSCD 1999年第3期239-240,共2页
As an interconnector of solid oxide fuel cell, La 1-x Ca x CrO 3( x =0 0~0 5) were prepared by sol gel method. The crystal structures of La 1-x Ca x CrO 3 at room temperature are the or... As an interconnector of solid oxide fuel cell, La 1-x Ca x CrO 3( x =0 0~0 5) were prepared by sol gel method. The crystal structures of La 1-x Ca x CrO 3 at room temperature are the orthorhombic perovskite GdFeO 3 type. XPS analysis indicates that chrome ions are in different valence state. The introduction of Ca 2+ into the lattice induces the oxidation of Cr 3+ to Cr 6+ . With x increasing, the amount of Cr 6+ increases. The present of the more Cr 6+ is one of the important factors that effect electric conductivity of La 1-x Ca x CrO 3. 展开更多
关键词 Rare earths La 1-x Ca x CrO 3 High temperature conductivity interconnector
下载PDF
Guang Dong, Hong Kong and Macao Initiates Cross-Region Cooperation in Protecting Intellectual Property
9
作者 Shi Zhihong Mo Yaojiang +1 位作者 Wang Hu Hu Yuzhang 《China's Foreign Trade》 2002年第11期53-53,共1页
关键词 Guang Dong Hong Kong and Macao Initiates cross-region Cooperation in Protecting Intellectual Property
下载PDF
HDI板铜箔压合剥离强度探讨
10
作者 邹定明 陆永平 +2 位作者 金立奎 曾祥刚 李伟 《印制电路信息》 2023年第8期61-64,共4页
随着智能电子产品向轻薄化及多功能化发展,高阶高密度互连板(HDI)12层及以上产品对铜箔剥离强度要求越来越高。铜箔剥离强度在印制电路板(PCB)层压前后变化不大,因此铜箔的剥离强度是影响PCB剥离强度的关键因素。选取A、B、C、D四种不... 随着智能电子产品向轻薄化及多功能化发展,高阶高密度互连板(HDI)12层及以上产品对铜箔剥离强度要求越来越高。铜箔剥离强度在印制电路板(PCB)层压前后变化不大,因此铜箔的剥离强度是影响PCB剥离强度的关键因素。选取A、B、C、D四种不同的铜箔进行对比测试。研究结果表明:剥离强度与设备及压合位置无关,与材料本身及设计强相关。 展开更多
关键词 高密度互连板(HDI) 剥离强度 粗糙度
下载PDF
改善高密度互连板镀铜填孔漏填的研究
11
作者 杨云 吴都 曹大福 《印制电路信息》 2023年第7期30-35,共6页
阐述高密度互连(HDI)板盲孔镀铜填孔过程中常见的漏填、凹陷和空洞3种缺陷,主要对漏填类型进行失效原因分析,其失效形态有盲孔底部钻穿、层压介厚超标、层压杂物、沉铜不良、填孔气泡和槽内杂物6类。根据可能存在的影响因素,对气泡、粉... 阐述高密度互连(HDI)板盲孔镀铜填孔过程中常见的漏填、凹陷和空洞3种缺陷,主要对漏填类型进行失效原因分析,其失效形态有盲孔底部钻穿、层压介厚超标、层压杂物、沉铜不良、填孔气泡和槽内杂物6类。根据可能存在的影响因素,对气泡、粉尘杂物和药水性能进行研究,提出合理的关键控制点,为HDI板填孔漏填改善提供有效的研究方向。 展开更多
关键词 高密度互连(HDI)板 盲孔 镀铜填孔 漏填
下载PDF
高密度互连技术在系统级封装中的应用
12
作者 杨鹏飞 肖安云 +1 位作者 田重庆 黄健铭 《印制电路信息》 2023年第2期40-43,共4页
系统级封装(SiP)在无线通信领域应用广泛,促使无线通信向低成本、便携式、多功能、高性能等方向发展。SiP对印制电路板(PCB)的精密度要求越来越高,在品质要求和制作工艺方面也越来越复杂。由于SiP模组中集成了众多器件,假设每道工序良... 系统级封装(SiP)在无线通信领域应用广泛,促使无线通信向低成本、便携式、多功能、高性能等方向发展。SiP对印制电路板(PCB)的精密度要求越来越高,在品质要求和制作工艺方面也越来越复杂。由于SiP模组中集成了众多器件,假设每道工序良率有一点损失,叠乘后整个模组的良率损失则会变得巨大,故对PCB工艺提出了较高的要求,比如高对准度控制、精细线路加工、板边半孔成型加工、严格的外形成型尺寸控制等。本文对这类SiP可能涉及到的关键工艺、技术等展开研究。研究结果显示,突破各制程关键技术后,产品良率显著提高,其产品质量均符合客户品质要求。该SiP在HDI板制程过程中遇到的难点与解决方案,可供业界同行参考和借鉴。 展开更多
关键词 系统级封装 填孔 高密度互连 制作工艺难点
下载PDF
高密度互连板多张芯板防叠错方法
13
作者 郭达文 孙劼 +1 位作者 曾龙 文伟峰 《印制电路信息》 2023年第6期31-34,共4页
随着电子产品不断向小型化、多功能化、高速化方向发展,高密度互连(HDI)印制电路板(PCB)所用芯板层次也越来越多,预防HDI板多张芯板层次顺序叠错并进行有效控制,成为HDI板制程控制的关键。通过资料设计,利用目视检查、自动光学检查、设... 随着电子产品不断向小型化、多功能化、高速化方向发展,高密度互连(HDI)印制电路板(PCB)所用芯板层次也越来越多,预防HDI板多张芯板层次顺序叠错并进行有效控制,成为HDI板制程控制的关键。通过资料设计,利用目视检查、自动光学检查、设备扫码、附连测试板等过程检测管控方法,可以有效避免HDI多张芯板层次顺序叠错以及流出。该方法可为做好HDI板制程放叠错提供参考。 展开更多
关键词 高密度互连(HDI) 多张芯板 防叠错
下载PDF
高电流测试对激光孔可靠性确认的应用研究
14
作者 金立奎 严志豪 谢家星 《印制电路信息》 2023年第9期44-48,共5页
目前,印制电路板(PCB)厂大多通过高电流测试(HCT)设备对激光孔底部开裂风险进行监控。在实际生产中,偶尔会有HCT测试板经高电流测试时未出现异常,但在组装使用中个别测试板因激光孔底部开裂,导致电子产品功能异常的情况发生。针对盲孔... 目前,印制电路板(PCB)厂大多通过高电流测试(HCT)设备对激光孔底部开裂风险进行监控。在实际生产中,偶尔会有HCT测试板经高电流测试时未出现异常,但在组装使用中个别测试板因激光孔底部开裂,导致电子产品功能异常的情况发生。针对盲孔孔径、盲孔节距及盲孔数3种因子设计不同类型的HCT附连测试板进行测试,分析同叠构不同设计测试板在经高电流测试时的差异情况,得出影响HCT附连测试板测试结果的设计因素及测试条件,供同行参考。 展开更多
关键词 高电流测试 高阶高密度互连 激光孔底部开裂 附连测试板
下载PDF
固体氧化物燃料电池材料的研究进展 被引量:43
15
作者 刘旭俐 马峻峰 +3 位作者 刘文化 徐刚 李海舰 杨琳琳 《硅酸盐通报》 CAS CSCD 2001年第1期24-29,共6页
本文对燃料电池的研究发展进行了概述 ,详细地介绍了固体氧化物燃料电池的电解质材料、阴极材料、阳极材料及互连材料 。
关键词 固体氧化物燃料电池 电解质材料 阴极材料 阳极材料 互连材料
下载PDF
铬酸镧材料的研究现状及应用领域 被引量:15
16
作者 孙良成 李胜利 +2 位作者 刘伟明 敖青 李德辉 《稀土》 EI CAS CSCD 北大核心 2002年第6期53-56,共4页
铬酸镧(LaCrO3)是一种钙钛矿型(ABO3)复合氧化物,具有很高的熔点(2490℃)。它在掺杂Ca、Sr和Mg等二价碱土金属后具有很多特殊的性质。在高温发热材料、固体氧化物燃料电池连接材料、催化剂、NTC热敏电阻等方面都得到广泛的应用,是一种... 铬酸镧(LaCrO3)是一种钙钛矿型(ABO3)复合氧化物,具有很高的熔点(2490℃)。它在掺杂Ca、Sr和Mg等二价碱土金属后具有很多特殊的性质。在高温发热材料、固体氧化物燃料电池连接材料、催化剂、NTC热敏电阻等方面都得到广泛的应用,是一种很有前途的功能陶瓷材料。本文就其应用及研究现状进行了综述。 展开更多
关键词 铬酸镧 SOFC 连接材料 催化剂 NTC 功能陶瓷 结构 钙钛矿型复合氧化物 制备工艺
下载PDF
La_1-_xCa_xCrO_3连接材料的研制 被引量:7
17
作者 刘晓梅 吕喆 +3 位作者 刘江 裴力 何岚鹰 苏文辉 《中国稀土学报》 CAS CSCD 北大核心 1999年第2期191-192,共2页
用溶胶凝胶法制备了单相性和均匀性好的La1-xCaxCrO3(x=0~05)系列材料。X射线衍射分析表明,当0≤x≤05时样品具有畸变的正交钙钛矿(GdFeO3型)结构。XPS测量确定了样品中存在Cr离子从Cr... 用溶胶凝胶法制备了单相性和均匀性好的La1-xCaxCrO3(x=0~05)系列材料。X射线衍射分析表明,当0≤x≤05时样品具有畸变的正交钙钛矿(GdFeO3型)结构。XPS测量确定了样品中存在Cr离子从Cr3+变到Cr6+的变价现象,随着x的增加样品中Cr6+的含量增加。 展开更多
关键词 稀土 镧钙铬 复合氧化物 连接材料 燃料电池
下载PDF
固体氧化物燃料电池复合掺杂材料研究进展 被引量:9
18
作者 马文会 谢刚 陈秀华 《功能材料》 EI CAS CSCD 北大核心 2001年第5期449-452,共4页
概述了中温固体氧化物燃料电池构件使用的新型复合掺杂材料研究及制备进展 ,采用差示扫描量热法 (DSC)、热重法 (TG)与变温度X射线衍射对La1-xSrxMn1-yCoyO3、La1-x-zSrxCazMn1-yCoyO3复合掺杂钙钛矿结构氧化物的固相烧结合成过程进行... 概述了中温固体氧化物燃料电池构件使用的新型复合掺杂材料研究及制备进展 ,采用差示扫描量热法 (DSC)、热重法 (TG)与变温度X射线衍射对La1-xSrxMn1-yCoyO3、La1-x-zSrxCazMn1-yCoyO3复合掺杂钙钛矿结构氧化物的固相烧结合成过程进行了研究 。 展开更多
关键词 中温 固体氧化物 燃料电池 复合掺杂材料 阴极 电解质 互连接
下载PDF
中温固体氧化物燃料电池SUS430/La_(0.8)Sr_(0.2)MnO_3复合连接板材料制备研究 被引量:2
19
作者 刘石明 邢长生 +2 位作者 钱晓良 肖建中 张海鸥 《材料科学与工程学报》 CAS CSCD 北大核心 2005年第1期4-7,共4页
采用溶胶凝胶和等离子喷涂的方法 ,制备了SUS4 30 La0 .8Sr0 .2 MnO3复合连接板材料。通过TG、IR和XRD分析了La0 .8Sr0 .2 MnO3凝胶烧结过程 ;采用SEM、四探针法和氧化增重法分别研究了SUS4 30 La0 .8Sr0 .2 MnO3复合连接板材料的形... 采用溶胶凝胶和等离子喷涂的方法 ,制备了SUS4 30 La0 .8Sr0 .2 MnO3复合连接板材料。通过TG、IR和XRD分析了La0 .8Sr0 .2 MnO3凝胶烧结过程 ;采用SEM、四探针法和氧化增重法分别研究了SUS4 30 La0 .8Sr0 .2 MnO3复合连接板材料的形貌、电子导电能力和高温抗氧蚀能力。经比较研究发现 ,溶胶凝胶和等离子喷涂都可以制备出高性能的SUS4 30 La0 .8Sr0 .2 MnO3复合连接板材料 ,陶瓷涂层致密度分别达到了 94 .6 %和 97% ;且腐蚀速率由SUS4 30材料的10 4 .93μg2 ·cm- 4·h- 1 分别降低到 2 6 .91μg2 ·cm- 4·h- 1 和 2 0 .39μg2 ·cm- 4·h- 1 ,在 80 0°C下它们的电导率分别为 11.17s·cm- 1和 12 .6 6s·cm- 1 。 展开更多
关键词 固体氧化物燃料电池 掺杂锰酸镧 铁基合金 陶瓷涂层 复合连接板
下载PDF
LaCoO_3涂层在SOFC金属连接体中的应用 被引量:4
20
作者 蒲健 华斌 李箭 《电池》 CAS CSCD 北大核心 2006年第5期380-382,共3页
通过溶胶-凝胶技术,在Fe-16Cr合金上施加LaCoO3导电涂层,研究了涂层对Fe-16Cr合金作为SOFC金属连接体的影响。利用X射线衍射和扫描电镜研究涂层和氧化物膜的结构和表面微观形貌。通过比较具有LaCoO3涂层的合金和Fe-16Cr合金之间的氧... 通过溶胶-凝胶技术,在Fe-16Cr合金上施加LaCoO3导电涂层,研究了涂层对Fe-16Cr合金作为SOFC金属连接体的影响。利用X射线衍射和扫描电镜研究涂层和氧化物膜的结构和表面微观形貌。通过比较具有LaCoO3涂层的合金和Fe-16Cr合金之间的氧化动力学过程,发现在200~500h之间,具有LaCoO3导电涂层的合金和Fe-16Cr合金的抛物线常数分别为6.64×10^-10g^2/cm^4·s和6.62×10^-9g^2/cm^4·s,LaCoO3能有效地降低Fe-16Cr金属连接体的氧化速率,提高其高温导电能力。 展开更多
关键词 固体氧化物燃料电池(SOFC) 金属连接体 LaCoO3涂层 氧化动力学
下载PDF
上一页 1 2 3 下一页 到第
使用帮助 返回顶部