Maintaining stability as well as optimizing recovery of crown pillar, a pillar separating surface area with the uppermost stope in overhand cut and fill underground mining method, is important. Failures in stope may l...Maintaining stability as well as optimizing recovery of crown pillar, a pillar separating surface area with the uppermost stope in overhand cut and fill underground mining method, is important. Failures in stope may lead to crown pillar failures and cause surface subsidence. Increasing crown pillar thickness will increase crown pillar stability yet reduce mining recovery because part of crown pillar is formed by ore body. Preventing stope failure is the key to maintain stability and optimize recovery of crown pillar. Therefore, it is important to study countermeasure method for stope failure especially in crown pillar area. An attempt has been made to investigate the effectiveness of various countermeasures for stope failure in crown pillar area by means of parametric study. The result shows active type support system is effective for supporting stope in high vertical stress condition while the passive one needs to be installed if the stope is opened in high horizontal stress condition. In general, more supporting capacity from both type support systems is needed if the stope is opened in more severe geological condition. Another countermeasures, sill pillar and surface pile, are introduced for stope instability in crown pillar and non-crown pillar area. Sill pillar is an abandoned slice of unstable stope based on stability analysis. Sill pillar is very effective to stabilize stope both in crown pillar and non-crown pillar area, especially for stope in high horizontal stress condition. Sill pillar application in model with stress ratio 2 can optimize 20 meter thickness of crown pillar into 5 meter. Another proposed countermeasure is surface pile. Surface pile can be installed from the surface to improve stability of crown pillar and stope. The most effective use of surface pile is found in simulation of model with stress ratio 0.75 where surface pile can optimize 15 meter thickness of crown pillar into 5 meter.展开更多
Irregular plates are very common structures in engineering,such as ore structures in mining.In this work,the Galerkin solution to the problem of a Kirchhoff plate lying on the Winkler foundation with two edges simply ...Irregular plates are very common structures in engineering,such as ore structures in mining.In this work,the Galerkin solution to the problem of a Kirchhoff plate lying on the Winkler foundation with two edges simply supported and the other two clamped supported is derived.Coordinate transformation technique is used during the solving process so that the solution is suitable to irregular shaped plates.The mechanical model and the solution proposed are then used to model the crown pillars between two adjacent levels in Sanshandao gold mine,which uses backfill method for mining operation.After that,an objective function,which takes security,economic profits and filling effect into consideration,is built to evaluate design proposals.Thickness optimizations for crown pillars are finally conducted in both conditions that the vertical stiffness of the foundation is known and unknown.The procedure presented in the work provides the guidance in thickness designing of complex shaped crown pillars and the preparation of backfill materials,thus to achieve the best balance between security and profits.展开更多
Minerals are now being extracted from deep mines due to drying up of resource in shallow ground. The need for suitable supports and ground control mechanisms for safe mining necessitates proper pillar design with fill...Minerals are now being extracted from deep mines due to drying up of resource in shallow ground. The need for suitable supports and ground control mechanisms for safe mining necessitates proper pillar design with filling technology. In addition, high horizontal stress may cause collapse of hanging wall and footwall rocks, hence designing of suitable crown pillars is absolutely necessary for imposing overall safety of the stopes. This paper provides a methodology for the evaluation of the required thickness of crown pillars for safe operation at depth ranging from 600 m to 1000 m. Analyses are conducted with the results of 108 non-linear numerical models considering Drucker-Prager material model in plane strain condition. Material properties of ore body rock and thickness of crown pillars are varied and safety factors of pillars estimated. Then, a generalized statistical relationship between the safety factors of crown pillars with the various input parameters is developed. The developed multivariate regression model is utilized for generating design/stability charts of pillars for different geo-mining conditions.These design charts can be used for the design of crown pillar thickness with the depth of the working,taking into account the changes of the rock mass conditions in underground metal mine.展开更多
文摘Maintaining stability as well as optimizing recovery of crown pillar, a pillar separating surface area with the uppermost stope in overhand cut and fill underground mining method, is important. Failures in stope may lead to crown pillar failures and cause surface subsidence. Increasing crown pillar thickness will increase crown pillar stability yet reduce mining recovery because part of crown pillar is formed by ore body. Preventing stope failure is the key to maintain stability and optimize recovery of crown pillar. Therefore, it is important to study countermeasure method for stope failure especially in crown pillar area. An attempt has been made to investigate the effectiveness of various countermeasures for stope failure in crown pillar area by means of parametric study. The result shows active type support system is effective for supporting stope in high vertical stress condition while the passive one needs to be installed if the stope is opened in high horizontal stress condition. In general, more supporting capacity from both type support systems is needed if the stope is opened in more severe geological condition. Another countermeasures, sill pillar and surface pile, are introduced for stope instability in crown pillar and non-crown pillar area. Sill pillar is an abandoned slice of unstable stope based on stability analysis. Sill pillar is very effective to stabilize stope both in crown pillar and non-crown pillar area, especially for stope in high horizontal stress condition. Sill pillar application in model with stress ratio 2 can optimize 20 meter thickness of crown pillar into 5 meter. Another proposed countermeasure is surface pile. Surface pile can be installed from the surface to improve stability of crown pillar and stope. The most effective use of surface pile is found in simulation of model with stress ratio 0.75 where surface pile can optimize 15 meter thickness of crown pillar into 5 meter.
基金Project (51504044) supported by the National Natural Science Foundation of ChinaProject (14KF05) supported by the Research Fund of the State Key Laboratory of Coal Resources and Mine Safety(CUMT),China+2 种基金Project (2015CDJXY) supported by the Fundamental Research Funds for the Central Universities,ChinaProject (2015M570607) supported by Postdoctoral Science FoundationProject (2011DA105287-MS201503) supported by the Independent Subject of State Key Laboratory of Coal Mine Disaster Dynamics and Control,China
文摘Irregular plates are very common structures in engineering,such as ore structures in mining.In this work,the Galerkin solution to the problem of a Kirchhoff plate lying on the Winkler foundation with two edges simply supported and the other two clamped supported is derived.Coordinate transformation technique is used during the solving process so that the solution is suitable to irregular shaped plates.The mechanical model and the solution proposed are then used to model the crown pillars between two adjacent levels in Sanshandao gold mine,which uses backfill method for mining operation.After that,an objective function,which takes security,economic profits and filling effect into consideration,is built to evaluate design proposals.Thickness optimizations for crown pillars are finally conducted in both conditions that the vertical stiffness of the foundation is known and unknown.The procedure presented in the work provides the guidance in thickness designing of complex shaped crown pillars and the preparation of backfill materials,thus to achieve the best balance between security and profits.
文摘Minerals are now being extracted from deep mines due to drying up of resource in shallow ground. The need for suitable supports and ground control mechanisms for safe mining necessitates proper pillar design with filling technology. In addition, high horizontal stress may cause collapse of hanging wall and footwall rocks, hence designing of suitable crown pillars is absolutely necessary for imposing overall safety of the stopes. This paper provides a methodology for the evaluation of the required thickness of crown pillars for safe operation at depth ranging from 600 m to 1000 m. Analyses are conducted with the results of 108 non-linear numerical models considering Drucker-Prager material model in plane strain condition. Material properties of ore body rock and thickness of crown pillars are varied and safety factors of pillars estimated. Then, a generalized statistical relationship between the safety factors of crown pillars with the various input parameters is developed. The developed multivariate regression model is utilized for generating design/stability charts of pillars for different geo-mining conditions.These design charts can be used for the design of crown pillar thickness with the depth of the working,taking into account the changes of the rock mass conditions in underground metal mine.
