基于FLUX3D的变压器油箱和夹件杂散损耗分析研究

开展杂散损耗分析有助于提高变压器运行效率。本文利用法国FLUX3D软件建立了一个考虑油箱和夹件损耗的SFL1-20000/35变压器有限元模型,获得了变压器油箱和夹件的涡流分布和损耗估计值。通过自定义B(H)磁滞曲线参数,采用线性表面阻抗法和非线性表面阻抗法分别计算了变压器油箱壁及夹件涡流损耗。与国标参数/出厂测试参数校核结果显示非线性表面阻抗法具有准确性更高的特点。相关模型构建的讨论与计算结论对于标准或特种变压器的优化设计和运行分析具有一定的参考价值。

Physical Properties and Regulating Mechanism of Fluoride-Free and Harmless B_2O_3-Containing Mould Flux

The flux agents in common mould fluxes were fluoride and sodium oxide, which would do great harm to environments. B2O3 was selected as flux. The physical properties of B2O3-containing mould fluxes were studied. The corresponding physical properties of 37. 91% CAO-43.09% SiO2-5% Al2O3-5% MgO-2% Li20-7% B2O3 mould fluxes were as follows： the melting point was 909℃, the flowing temperature was 1 160℃, the viscosity and surface tension at 1300 ℃ were 0. 4 Pa · s and 0.32 N/m respectively, which could meet the demands for certain kinds of steels for mould fluxes in continuous casting.

Characterization of Y_2O_2S∶Eu ^(3+), Mg^(2+), Ti^(4+) Long-Lasting Phosphor Synthesized by Flux Method

Long-lasting phosphor Y2O2S ： Eu^3＋ , Mg^2＋ , Ti^4＋ was synthesized by a flux method and their luminescence properties were investigated. The result indicates that the unit cell parameter c is linearly increased with the increase of Eu2O3 content in Y2O2S： Eu^3＋ （0.01 ≤ x ≤0.10）. On the other hand, the change of unit cell parameter a is not linear dependence. In the Y2O2S： Eu^3 ＋ crystal structure, Eu^3＋ ions only replaced Y^3 ＋ ions＇ places in which it posited center position of c axis. With the increase of Eu2O3 content, the position of the strongest emission peak changed from 540 nm （5D1→^ 7F2 transition） to 626 nm （^5Do→^7TF2 transition）, and the maximum intensity was obtained when x = 0.09 in Y2O2S： Eu^3＋ （0.01 ≤x ≤0.10）. This is due to the environment of trivalent europium in the crystal structure of Y2O2S. Doping with Mg^2＋ or Ti^4＋. ions alone cannot get the good long-lasting afterglow effect, whereas co-doping with Mg^2 ＋ and Ti^4 ＋ ions and excited with 365 nm ultraviolet light, a strong thermoluminesence peak appeared, red and orange long-lasting phosphorescence （LLP） was also observed and the phosphorescence lasted nearly 3 h in the light perception of the dark-adapted human eye （0.32 mcd·m^-2）. Thus the LLP mechanism was analyzed.

Fracture Mechanics,Crack Propagation and Microhardness Studies on Flux Grown ErAlO_3 Single Crystals

Results on fracture mechanics and crack propagation have been obtained, making use of Vickers microhardness studies on two different crystallographic planes [(110) and (001)] of flux grown erbium aluminate crystals in the load ranging from 10-100 g. The variation of microhardness with load which is best explained by Hays and Kendall's law leads to the load independent values of hardness. Classification of cracks is dealt with and it is reported that the transition from Palmqvist to median types of cracks occurs at higher loads. The values of fracture toughness (K_C), and brittleness index (B_i) are calculated using median types of cracks.

Strongly enhanced flux pinning in the YBa_2Cu_3O_(7-X) films with the co-doping of Ba TiO_3 nanorod and Y_2O_3 nanoparticles at 65 K

YBa2Cu3O7-x（YBCO） films with co-doping BaTiO3（BTO） and Y2O3 nanostructures were prepared by metal organic deposition using trifluoroacetates（TFA-MOD）. The properties of the BTO/Y2O3co-doped YBCO films with different excess yttrium have been systematically studied by x-ray diffraction（XRD）, Raman spectra, and scanning electron microscope（SEM）. The optimized content of yttrium excess in the BTO/Y2O3co-doped YBCO films is 10 mol.%, and the critical current density is as high as - 17 mA/cm^2（self-field, 65 K） by the magnetic signal. In addition, the Y2Cu2O5 was formed when the content of yttrium excess increases to 24 mol.%, which may result in the deterioration of the superconducting properties and the microstructure. The unique combination of the different types of nanostructures of BTO and Y2O3 in the doped YBCO films, compared with the pure YBCO films and BTO doped YBCO films, enhances the critical current density（JC） not only at the self-magnetic field, but also in the applied magnetic field.

EFFECT OF Fe_2O_3 ON WELDING TECHNOLOGY AND MECHANICAL PROPERTIES OF WELD METAL DEPOSITED BY SELF-SHIELDED FLUX CORED WIRE

Five experimental self-shielded flux cored wires are fabricated withdifferent amount of Fe_2O_3 in the flux. The effect of Fe_2O_3 on welding technology and mechanicalproperties of weld metals deposited by these wires are studied. The results show that with theincrease of Fe_2O_3 in the mix, the melting point of the pretreated mix is increased. LiBaF_3 andBaFe_(12)O_(19), which are very low in inherent moisture, are formed after the pretreatment. Themechanical properties are evaluated to the weld metals. The low temperature notch toughness of theweld metals is increased linearly with the Fe_2O_3 content in the flux due to the balance betweenFe_2O_3 and residual Al in the weld metal. The optimum Fe_2O_3 content in flux is 2.5 percent approx3.5 percent.

Growth of Emerald Crystals byEvaporation of Na_2O-MoO_3 Flux

Well-formed crystals of emerald, Be3AI2Si6O18:Cr, were easily grown from an Na2O-MoO3 flux by an isothermal technique. The crystal growth was conducted by heating a mixture of solute and flux at 1 100 ℃ for 24 h. The evaporation loss of flux depended on the amount of Na2O added to MoO3. Emerald crystals of lengths up to 2.1 mm and widths of 1. 4 mm were grown. The crystal sizes were dependent on the evaporation loss of the flux. The obtained crystals were transparent and exhibited the typical emerald-green color. The form of the emerald crystals was a twelve-sided prism bounded by well-developed faces. The aspect ratios were in the region of 1. 4 to 2. 3. The density was (2. 64±0.02) g/cm3. The IR absorption bands were in good agreement with the literature data.

Strong flux pinning enhancement in YBa_2Cu_3O_(7-x) films by embedded BaZrO_3 and BaTiO_3 nanoparticles

YBa2Cu3O7-x （YBCO） films with embedded BaZrO3 and BaTiO3 nanoparticles were fabricated by metalorganic deposition using trifluoroacetates （TFA-MOD）. Both X-ray diffraction and transmission electron microscopy revealed that these BaZrO3 and BaTiO3 nanoparticles had random orientations and were distributed stochastically in the YBCO matrix. The unique combined microstructure enhances the critical current density （Jc） of the BaZrO3/BaTiO3 doped-YBCO films, while keeping the critical transition temperature （Tc） close to that in the pure YBCO films. These results indicate that BaZrO3 and BaTiO3 nanoparticles provide strong flux pinning in YBCO films.

Effects of CeF_3 on properties of self-shielded flux cored wire

Effects of CeF3 on properties of self-shielded flux cored wire including welding process, inclusions in weld metal and mechanical properties are systematically studied. Welding smoke and spatter are reduced with the addition of CeF3. The main non-metallic inclusions in weld metal are AlN and Al2O3. CeF3 can refine non-metallic inclusions and reduce the amount of large size inclusions, which is attributed to the inclusion floating behavior during the solidification of weld metal. The low temperature impact toughness is improved by adding suitable amount of CeF3 in the flux.

B_(2)O_(3)对CaO-Al_(2)O_(3)-B_(2)O_(3)三元保护渣熔体结构的影响

通过分子动力学方法对非反应性保护渣CaO-Al_(2)O_(3)-B_(2)O_(3)三元渣系进行了模拟,构建了熔渣的网络结构模型,研究了渣系中B_(2)O_(3)的含量对保护渣熔渣微观结构的影响规律。结果表明:B在网络中与O的结合能力最强,且能够起到简化网络和平衡过剩电荷的作用;Al在熔体中主要以4配位形式存在,同时存在少量高配位Al-O结构,B_(2)O_(3)的含量为5%时,熔渣中[AlO_(4)]含量最高;随着B_(2)O_(3)含量的增多,熔渣网络结构聚合程度降低,复杂Al-O结构减少,熔渣微结构的有序性增加。

Developing a 3D-FEM Model for Electromagnetic Analysis of an Axial Flux Permanent Magnet Machine

Recently, many optimal designs for axial flux permanent magnet (AFPM) motors were performed based on finite- element (FE) analysis. Most of the models are based on reduction of 3D problem to 2D problem which is not accurate for design aspects. This paper describes an accurate electromagnetic analysis of a surface mounted, 28 pole AFPM with concentrated stator winding. The AFPM is modeled with three-dimensional finite-element method. This model in-cludes all geometrical and physical characteristics of the machine components. Using this accurate modeling makes it possible to obtain demanded signals for a very high precision analysis. Magnetic flux density, back-EMF, magnetic axial force and cogging torque of the motor are simulated using FLUX-3D V10.3.2. Meanwhile, the model is paramet-ric and can be used for design process and sensitivity analysis.

Thermal stability and electrical transport properties of Ge/Sn-codoped single crystalline β-Zn4Sb3 prepared by the Sn-flux method

This study prepares a group of single crystalline β-Zn_4Sb_3 with Ge and Sn codoped by the Sn-flux method according to the nominal stoichiometric ratios of Zn_（4.4）Sb_3 Ge_xSn_3（x = 0–0.15）. The prepared samples possess a metallic luster surface with perfect appearance and large crystal sizes. The microscopic cracks or defects are invisible in the samples from the back-scattered electron image. Except for the heavily Ge-doped sample of x = 0.15, all the samples are single phase with space group R3c. The thermal analysis results show that the samples doped with Ge exhibit an excellent thermal stability.Compared with the polycrystalline Ge-substituted β-Zn_4Sb_3, the present single crystals have higher carrier mobility, and hence the electrical conductivity is improved, which reaches 7.48×10~4S·m^（-1） at room temperature for the x = 0.1 sample.The change of Ge and Sn contents does not improve the Seebeck coefficient significantly. Benefiting from the increased electrical conductivity, the sample with x = 0.075 gets the highest power factor of 1.45×10^（-3）W·m^（-1）·K^（-2） at 543 K.

Winding Function Model-based Performance Evaluation of a PM Transverse Flux Generator for Applications in Direct-drive Systems

The magnetic flux in a permanent magnet transverse flux generator(PMTFG) is three-dimensional(3D), therefore, its efficacy is evaluated using 3D magnetic field analysis. Although the 3D finite-element method(FEM) is highly accurate and reliable for machine simulation, it requires a long computation time, which is crucial when it is to be used in an iterative optimization process. Therefore, an alternative to 3DFEM is required as a rapid and accurate analytical technique. This paper presents an analytical model for PMTFG analysis using winding function method. To obtain the air gap MMF distribution, the excitation magneto-motive force(MMF) and the turn function are determined based on certain assumptions. The magnetizing inductance, flux density, and back-electro-magnetomotive force of the winding are then determined. To assess the accuracy of the proposed method, the analytically calculated parameters of the generator are compared to those obtained by a 3D-FEM. The presented method requires significantly shorter computation time than the 3D-FEM with comparable accuracy.

Milk fat globule epidermal growth factor 8 alleviates liver injury in severe acute pancreatitis by restoring autophagy flux and inhibiting ferroptosis in hepatocytes

BACKGROUND Liver injury is common in severe acute pancreatitis(SAP).Excessive autophagy often leads to an imbalance of homeostasis in hepatocytes,which induces lipid peroxidation and mitochondrial iron deposition and ultimately leads to ferroptosis.Our previous study found that milk fat globule epidermal growth factor 8(MFG-E8)alleviates acinar cell damage during SAP via binding toαvβ3/5 integrins.MFG-E8 also seems to mitigate pancreatic fibrosis via inhibiting chaperone-mediated autophagy.AIM To speculate whether MFG-E8 could also alleviate SAP induced liver injury by restoring the abnormal autophagy flux.METHODS SAP was induced in mice by 2 hly intraperitoneal injections of 4.0 g/kg L-arginine or 7 hly injections of 50μg/kg cerulein plus lipopolysaccharide.mfge8-knockout mice were used to study the effect of MFG-E8 deficiency on SAPinduced liver injury.Cilengitide,a specificαvβ3/5 integrin inhibitor,was used to investigate the possible mechanism of MFG-E8.RESULTS The results showed that MFG-E8 deficiency aggravated SAP-induced liver injury in mice,enhanced autophagy flux in hepatocyte,and worsened the degree of ferroptosis.Exogenous MFG-E8 reduced SAP-induced liver injury in a dose-dependent manner.Mechanistically,MFG-E8 mitigated excessive autophagy and inhibited ferroptosis in liver cells.Cilengitide abolished MFG-E8’s beneficial effects in SAP-induced liver injury.CONCLUSION MFG-E8 acts as an endogenous protective mediator in SAP-induced liver injury.MFG-E8 alleviates the excessive autophagy and inhibits ferroptosis in hepatocytes by binding to integrinαVβ3/5.

Effect of B_(2)O_(3) enrichment on microstructural inhomogeneity of high strength steel weldments

The present work attributes the role of boron on the high strength steel submerged arc weld using an undermatching filler wire.Mild steel filler wire was used for welding in constant machine parameters setting to evaluate the joint strength due to the enrichment of boron.To change the chemical composition of the weld metal,boron trioxide powder was blended with virgin flux in various proportions(2.5%−12.5%),which led to an increase in boron weight percentage in the range of 0−0.0065.The results show that weld metals(WM)optical micrographs depict the various types of ferrites,pearlites and secondary phases like martensite-austenite(M-A).Acicular ferrite content was influenced by the boron trioxide addition.Heat affected zone(HAZ)micrographs were not showing appreciable changes with oxide enrichment.Hardness and toughness of weld metals showed the mixed trend with B_(2)O_(3) enrichment whereas,small reduction in ultimate tensile strength(UTS)and yield strength(YS)was observed.

助溶剂法生长的AgNbO_(3)晶体相转变特征、电学和光学性能

AgNbO_(3)具有反铁电性及高的极化强度,在智能器件领域有着重要的应用前景.本文采用助溶剂法合成了高质量的AgNbO_(3)单晶(最大尺寸5 mm×4 mm×4 mm),系统研究了其相转变特征、光学和电学性能.当AgNbO_(3)晶体处于正交M相时,保持着相同的畴结构;由M_(2)相转变至地相时,偏光显微镜(PLM)照片衬度变暗,同时电导率和介电损耗明显上升.当AgNbO_(3)单晶由M_(3)相到顺电O相时,畴结构消失;同时,表现出明显的热滞后现象,属于第一类相变.室温下,AgNbO_(3)单晶的直接带隙拟合禁带宽度为2.73 eV,略窄于AgNbO_(3)陶瓷.在临界电场以下,AgNbO_(3)单晶表现出更高的电致应变(0.076%,E_(m)=130 kV/cm).在绿色激光照射下,介电常数由70增至73,表现出明显的光致介电效应.

Dynamic Modelling of a Hybrid Variable Reluctance Machine Using the 3D Finite Element Method

This paper presents the work carried out to evaluate the dynamic performance of the Hybrid Variable Reluctance Motor (HVRM). The fourth-order Runge-Kutta integration algorithm was employed to solve the equations of the dynamic model, in conjunction with the three-dimensional finite element method. The 3D numerical data was calculated using Comsol Multiphysics, which accounts for the nonlinearity of the ferromagnetic material and the 3D nature of the HVRM. The outcomes of this study are precise and accurately predict the dynamic behaviour of the HVRM in terms of rotor position response, rotational speed and torque. The distinctive contribution of this work lies in the 3D numerical modelling of the HVRM and the subsequent evaluation and analysis of its dynamic operation. Analytical and numerical 2D studies are less resource-intensive and time-consuming, and are more straightforward and rapid to analyse and interpret. However, they are constrained in their capacity to examine spatial, volumetric interactions and intricate dynamics such as flux studies where three 3D effects cannot be disregarded, winding end effects and the configuration and positioning of the interposed permanent magnet.

Contribution to the Full 3D Finite Element Modelling of a Hybrid Stepping Motor with and without Current in the Coils

The paper presents our contribution to the full 3D finite element modelling of a hybrid stepping motor using COMSOL Multiphysics software. This type of four-phase motor has a permanent magnet interposed between the two identical and coaxial half stators. The calculation of the field with or without current in the windings (respectively with or without permanent magnet) is done using a mixed formulation with strong coupling. In addition, the local high saturation of the ferromagnetic material and the radial and axial components of the magnetic flux are taken into account. The results obtained make it possible to clearly observe, as a function of the intensity of the bus current or the remanent induction, the saturation zones, the lines, the orientations and the magnetic flux densities. 3D finite element modelling provide more accurate numerical data on the magnetic field through multiphysics analysis. This analysis considers the actual operating conditions and leads to the design of an optimized machine structure, with or without current in the windings and/or permanent magnet.

白光LED用红色荧光粉α-Gd_2(MoO_4)_3∶Eu的制备及其发光性能研究

以Gd2O3,MoO3,Eu2O3为原料,采用传统的高温固相反应方法制备了一种新的白光LED用红色荧光粉材料α相Gd2(MoO4)3∶Eu。利用XRD,SEM,激发和发射光谱对其进行了研究。分析了助熔剂和激活剂对样品的晶体结构,表面形貌和发光性能的影响。结果表明这种荧光粉可以被近紫外光(395nm)和蓝光(465nm)有效激发,发射峰值位于613nm(Eu3+离子的5D0→7F2跃迁)的红光,激发波长与目前广泛使用的蓝光和紫外光LED芯片相符合。因此,三价Eu离子激活的α相Gd2(MoO4)3是一种可能应用在白光LED上的红色荧光粉材料。

白光LED用红色发射荧光粉Gd2(MoO4)3：Eu^3＋制备与表征

以NH4F为助熔剂采用固相反应法合成了Eu3+掺杂的-αGd2(MoO4)3荧光粉。研究了引入不同含量助熔剂时对材料的结晶、荧光粉颗粒粒径、表面形貌及光谱性质的影响。实验结果表明,引入重量比为3%时样品具有好的结晶和优良的光谱性质;同时,随着助熔剂量的增加Eu3+离子在晶体中所处的格位对称性发生了变化;另外,通过Eu3+掺杂浓度变化的结果讨论了Eu3+的浓度猝灭行为。光谱测量的结果表明,该荧光粉与其他商品荧光粉不同,其最有效的激发波长不在电荷迁移带范围,而是465和395 nm跃迁,该荧光粉可作为近紫外LED和三基色荧光粉组合型白光器件的红色荧光粉的候选材料。