The electrical characteristics of Cu and Ni/Al AlGaN/GaN Schottky barrier diodes on Si su bstrates are compared. The onset voltage of Cu Schottky diodes is about 0.4 V less than the Ni/Al contact. For the Cu/Ni Schott...The electrical characteristics of Cu and Ni/Al AlGaN/GaN Schottky barrier diodes on Si su bstrates are compared. The onset voltage of Cu Schottky diodes is about 0.4 V less than the Ni/Al contact. For the Cu/Ni Schottky contact, the leakage current is 4.7 × 10^-7 A/mm at -10 V. After annealing, the leakage current is decreased to 3.7 × 10^-7 A/mm for 400℃ or 4.6 × 10^-8 A/mm for 500℃, respectively. The electrical property is affected by the thickness ratio of Cu to Ni. The Cu/Ni for 80/20 nm shows a low onset voltage, while the Cu/Ni for 20/80 nm shows a low leakage current. Both breakdown voltages are above 720 V.展开更多
An approach for the thermodynamics of the thermoelastic martensitic transformation in β-Cu base alloys is suggested.Driving forces for martensitic transformation,T_0 and M_s tempera- tures in Cu-Zn,Cu-Al and Cu-Zn-Al...An approach for the thermodynamics of the thermoelastic martensitic transformation in β-Cu base alloys is suggested.Driving forces for martensitic transformation,T_0 and M_s tempera- tures in Cu-Zn,Cu-Al and Cu-Zn-Al alloys were calculated and the calculated M_s are in good agreement with the experimental ones.Ordering of the parent phase lowers M_s(T_0)in Cu-Zn and Cu-Zn-Al alloys,but raises M_s(T_0)in Cu-Al alloys.Two methods for the es- timation of the critical driving force for the thermoelastic martensitic transformation are also introduced.展开更多
The combined effect of micro-alloying with Si and Ge and/or plastic deformation prior to ageing at 160°C on age hardening has been studied in an Al-2 at% Cu alloy. The results obtained indicate that the hardness ...The combined effect of micro-alloying with Si and Ge and/or plastic deformation prior to ageing at 160°C on age hardening has been studied in an Al-2 at% Cu alloy. The results obtained indicate that the hardness response is faster and the peak hardness is higher when plastic deformation and micro-alloying are applied together than performing each procedure individually. Different amounts of deformation, ranging from 0% to 30% have been utilized. An optimum deformation degree for the hardening response has been established around 8% for the Al-Cu-Si-Ge alloy. Characterization by transmission electron microscopy (TEM) shows that the peak hardness is due to a complex microstructure that contained θ" disc shaped precipitates, rod-shaped Si-Ge precipitates and θ' plates that were heterogeneously nucleated on the Si-Ge particles. Pre-deformation has been found to stimulate the growth of the θ' plates due to enhanced diffusion along dislocation cores. Increasing deformation reduces the influence of the Si-Ge precipitates on heterogeneous nucleation, leading to reduced peak hardness and faster over-ageing.展开更多
基金Supported by the National High Technology Research and Development Program of China under Grant No 2014AA032606 and No 2014AA032602the Beijing Municipal Science and Technology Project under Grant No Z131100005913001
文摘The electrical characteristics of Cu and Ni/Al AlGaN/GaN Schottky barrier diodes on Si su bstrates are compared. The onset voltage of Cu Schottky diodes is about 0.4 V less than the Ni/Al contact. For the Cu/Ni Schottky contact, the leakage current is 4.7 × 10^-7 A/mm at -10 V. After annealing, the leakage current is decreased to 3.7 × 10^-7 A/mm for 400℃ or 4.6 × 10^-8 A/mm for 500℃, respectively. The electrical property is affected by the thickness ratio of Cu to Ni. The Cu/Ni for 80/20 nm shows a low onset voltage, while the Cu/Ni for 20/80 nm shows a low leakage current. Both breakdown voltages are above 720 V.
文摘An approach for the thermodynamics of the thermoelastic martensitic transformation in β-Cu base alloys is suggested.Driving forces for martensitic transformation,T_0 and M_s tempera- tures in Cu-Zn,Cu-Al and Cu-Zn-Al alloys were calculated and the calculated M_s are in good agreement with the experimental ones.Ordering of the parent phase lowers M_s(T_0)in Cu-Zn and Cu-Zn-Al alloys,but raises M_s(T_0)in Cu-Al alloys.Two methods for the es- timation of the critical driving force for the thermoelastic martensitic transformation are also introduced.
文摘The combined effect of micro-alloying with Si and Ge and/or plastic deformation prior to ageing at 160°C on age hardening has been studied in an Al-2 at% Cu alloy. The results obtained indicate that the hardness response is faster and the peak hardness is higher when plastic deformation and micro-alloying are applied together than performing each procedure individually. Different amounts of deformation, ranging from 0% to 30% have been utilized. An optimum deformation degree for the hardening response has been established around 8% for the Al-Cu-Si-Ge alloy. Characterization by transmission electron microscopy (TEM) shows that the peak hardness is due to a complex microstructure that contained θ" disc shaped precipitates, rod-shaped Si-Ge precipitates and θ' plates that were heterogeneously nucleated on the Si-Ge particles. Pre-deformation has been found to stimulate the growth of the θ' plates due to enhanced diffusion along dislocation cores. Increasing deformation reduces the influence of the Si-Ge precipitates on heterogeneous nucleation, leading to reduced peak hardness and faster over-ageing.
基金the project of the Czech Science Foundation (No.20-19170S)the German Research Foundation (Deutsche Forschungsgemeinschaft (DFG))for financial support within the scope of project (No.SCHA 1484/46-1).
